HH-1001 - Heating Mirpol - Free user manual and instructions

Product Type	Oil-filled radiator heater
Model	HH-1001 (also HH-1002, HH-1011)
Dimensions (L x W x H)	33.5 x 24 x 55 cm
Weight	6 kg
Power Supply	220-240 V, 50-60 Hz
Max Power Consumption	1500 W
Heating Power Settings	600 W (I), 900 W (II), 1500 W (I+II)
Heating Ribs	7
Cable Length	1.8 m
Plug Type	CEE 7/7
Thermostat Control	Mechanical with adjustable knob
Safety Features	Overheating protection, tilt switch (tip-over protection)
Minimum Distances (top/back/sides/front)	100 cm each side
Intended Use	Indoor floor standing, occasional use or well-insulated rooms
Room Volume Minimum	4 m³
Maintenance	Wipe with soft cloth; no detergents; never submerge in water
Wheels Included	Yes, requires assembly
Certifications	CE, complies with EU directives 2014/35/EU and 2014/30/EU

Frequently Asked Questions - HH-1001 Mirpol

How do I assemble the wheels on my Mirpol HH-1001 heater?

Place the heater upside down on a scratch-free surface. Remove nuts from casters, insert caster bolts into the mounting base, and screw nuts back on. Attach yoke bolts between the first and second ribs (front) and between the last two ribs (rear). Secure with wing nuts without overtightening.

What should I do when using the heater for the first time?

An unusual smell may occur during first use or after long storage. This is normal. Ensure the device is placed upright on a stable, level surface, away from flammable materials. Unwind the power cord completely and check for damage before plugging in.

What are the heating power settings and how do I use them?

The heater has three power levels: Switch I (600 W), Switch II (900 W), and both switches simultaneously (1500 W). Use lower power for small rooms and higher power for larger spaces. Turn the thermostat knob clockwise to maximum, then adjust as needed.

Why does my heater make a noise after turning on?

The noise is normal and caused by the heating oil expanding as it warms up. No action is needed. The sound should diminish after the oil reaches operating temperature.

How do I clean and maintain the oil heater?

Always unplug and allow the heater to cool completely before cleaning. Wipe the surface with a soft, dry cloth. Do not use detergents, abrasive cleaners, or submerge the device in water. Keep electrical components dry.

What safety features does the HH-1001 have?

The heater is equipped with overheating protection (safety thermostat) that shuts off the unit if it gets too hot, and a tilt switch that turns off the heater if it tips over. Always place on a flat surface and maintain at least 100 cm clearance from walls and objects.

What should I do if the heater does not turn on?

Check the mains connection, power cord, and house fuses. Ensure the thermostat is set above room temperature. Verify the heater is upright on a flat surface – the tilt switch may have activated. If persistent, wait 10 minutes and try again. If still not working, contact Mirpol service.

Can I use the heater in a bathroom or outdoors?

No. The heater is only for indoor use in closed rooms. Do not use near bathtubs, showers, swimming pools, or any water source. Never use outdoors or in vehicles.

How should I store the heater when not in use?

Turn off and unplug the heater. Allow it to cool completely. Store upright in a cool, dry place away from dust, direct sunlight, and moisture. Do not place heavy objects on top of it.

How do I dispose of the heater at the end of its life?

Do not dispose of with household waste. According to EU Directive 2002/96/EU, return the device to a public collection point or point of sale. The heating oil must be drained and disposed of according to national regulations.

USER MANUAL HH-1001 Mirpol

Exterior view of a silver flat-screen solar oil heater with multiple cooling fans and wheels (no visible text or symbols)

HH-1001/1002/1011

GRZEJNIK OLEJOWY

EN | This product is only suitable for occasional use or for use in well-insulated rooms!

Importer:

Mirpol sp. z o.o.

Notes on the operating manual ....10

Safety 10

Device information ....13

Transport and storage 13

Installation and commissioning 13

Operation 14

Errors and faults ....15

Maintenance ....15

Technical annex 16

READ AND LEAVE THE USER MANUAL FOR ANOTHER REFERENCE!

The distributor is not liable for damage caused during transport, for damage resulting from improper use, voltage fluctuations or the use of modified spare parts.

Please read the information below carefully. They contain important instructions regarding the operation and maintenance of the device and its safe use. Please keep these instructions for future usage and pass it on to any subsequent owner of the device.

The device complies with the applicable technical regulations with the current safety regulations for devices.

The device meets the requirements of the Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limits and Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility (recast).

Notes on the operating manual

Warning against electric voltage

This symbol indicates a health risk and life threat, resulting from the presence of electric voltage.

Hot surface warning

This symbol indicates the health risk and life threat, resulting from touching the hot surface.

Warning

This symbol denotes a medium risk that can cause serious injury or death.

Carefully

This symbol denotes a medium risk that can cause serious injury or death.

Tip

This word identifies important information (e.g. possible material damage) that is not associated with a risk.

Information

Notes marked with this symbol help you to carry out work quickly and safely.

Follow the instruction manual

Information marked with this symbol reminds you to read the operating instructions.

Safety

Before starting the device, read the manual carefully and store the manual near the device or its site of use!

Warning

Read all safety tips and recommendations.

Failure to follow the safety instructions and recommendations may result in electric shock, fire and / or serious injury.

Keep all safety notes and recommendations for future reference.

The device may be operated by children from 8 years old and people with reduced physical, sensory or mental abilities or people without appropriate experience and knowledge, provided that they are supervised or trained in the safe use of the device and that they understand the dangers of using the device.

Children must not play with the device. Cleaning and user maintenance must not be made by unsupervised children.

Warning

Access to the device by children under 3 years of age is prohibited, unless they are constantly supervised.

Children from 3 to 8 years old may turn on the device only when supervised or after training in the safe use of the device and hazards occurring during operation. The condition is that the device is in its normal operating position and installed. Children from 3 to 8 years old may not connect the plug to the power socket, adjust, clean and / or maintain the device within the scope permitted by the user.

Warning

Do not use the device in small rooms with people who are unable to leave the room on their own and who are deprived of constant care.

It is forbidden to use and position the device in rooms or areas where there is a fire hazard.

• Do not use the device in rooms with an aggressive atmosphere.
• Place the device vertically on a firm surface.
• Allow the device to dry after wet cleaning.
• Do not use a wet device.
  Do not operate the device when wet hands.
• Do not aim direct stream of water at the device.
• Never put any objects into the device or body parts.
• Do not cover the working device.
• Do not remove safety signs, stickers or labels. Maintain all safety signs, stickers and labels in good condition.
• Never sit on the device.
• The device is not a toy. Maintain children and pets away from the machine. Do not operate the device without supervision.
• Before each use of the device check that its accessories and connection elements are not damaged. Do not use damaged devices or components.
• Make sure that all electric cables outside of the device are protected against damage (eg caused by animals). Under no circumstances operate the device with a damaged cable or mains connection!
• The power connection must comply with the specifications in the technical appendix.
• Insert the plug into an outlet equipped with an earthing system.
• Select an extension cord taking into account the power of the device, the necessary length and the intended use of the device. Completely unfold the extension cord. Avoid electrical overload.
• Before carrying out maintenance or repair work on the device, disconnect the power plug from the socket.
• When the device is not in use, switch it off and disconnect the power plug from the socket.
• If you find damage to the plugs or cables, do not use the device under any circumstances.
• In order to avoid a hazard, repair of the power supply cable of the device may only be performed by the manufacturer or the manufacturer's service or a qualified employee. Damaged electric cables are a serious health hazard.
• Obey when setting up the device to the guidelines regarding the minimum distance to other objects and to the recommendations on the conditions of storage and use in accordance with the „Technical Annex”.
• Provide a safety distance of at least 1 m between the unit's air outlet and any flammable substances such as textiles, curtains, beds and sofas.
• Make sure the air inlet and outlet are not obstructed.
• Make sure the air intake is not contaminated or obstructed by loose objects.
• Do not place the device on a flammable surface.
• Use original spare parts. Otherwise proper and safe operation the device cannot be guaranteed.

• Before commencing transport and / or carrying out maintenance activities wait for the device to cool down.

• Use the device away from bathtubs, shower trays, swimming pools or other reservoirs containing water. There is a risk of electric shock!

• Do not place the device directly below a power socket.
• Do not start the device if it tips over or shows visible signs of damage.

Intended use

The device is only intended for occasional use or for use in well insulated rooms.

The heater is intended for heating air in closed rooms. The device is intended for home use and is not suitable for professional use. The device will be perfect as an additional heating device. The appliance is intended for floor standing only.

Predictable misuse

• Do not place the device on damp or flooded ground.
• Do not put any objects, such as clothing, on the device.
• Do not operate the device near substances such as gasoline, solvents, paints or other substances generating flammable vapors, or in rooms where such substances are stored.
• Do not use the device outdoors.
• The device cannot be used for heating cars.
• The device must not be used near swimming pools.
• Use the device away from sinks, bathtubs or other tanks containing water. Never immerse the device in water.
• Do not operate in rooms with a volume of less than 4m^3 . Failure to do so may cause overheating!
• Any use of the device other than the intended use is a foreseeable misuse of the device.
• Do not make any structural changes or modifications to the device yourself.

User Qualifications

Users of the device must:

• know the risks associated with the operation of electrical devices in an environment with high air humidity.
• read the operating manual thoroughly, in particular with the chapter „Security”.

Maintenance operations that require opening the housing or opening the oil tank, may only be carried out by an electrical service or by Mirpol.

Symbols on the device.

Symbols

The symbol on the device indicates that it is forbidden to hang objects (e.g. towels, clothes, etc.) above or directly in front of the device. The device must not be covered as it may overheat and cause a fire!

Other dangers

Warning against electric voltage

Work on the electrical installation may only be carried out by an authorized electrical company.

Warning against electric voltage

Before starting any repairs of the device, disconnect the power plug from the socket! Do not touch the mains plug with wet or damp hands. Disconnect the device by pulling the power plug.

Hot surface warning

The parts of the device can be very hot and touching them may result in burns. Be especially careful in the vicinity of children or other people who require attention!

Warning

Incorrect operation carries a risk of electric shock. Use the device only for its intended purpose.

Warning

Additional dangers can arise if this device is used incorrectly! Ensure that your staff is properly trained!

Warning

The devices are not toys and must not be passed on to children.

Warning

Danger of suffocation!

Do not leave the packaging material lying around. It can become a dangerous toy for children.

Warning

There is a risk of fire if the appliance is not positioned correctly. Do not place the device on a flammable surface. Do not place the device on carpets with long bristles.

Warning

The device must not be covered as it may overheat and cause a fire!

Proceeding in an emergency

1. Turn off the device.
2. In an emergency, remove the device from the socket power supply: Disconnect the device by pulling the plug power.
3. Do not connect a damaged device to the power supply.

Overheating protection

The device is equipped with a safety thermostat (against exceeding the permissible operating temperature), activated when the device overheats.

Activating the safety thermostat will automatically turn off the heating. The heating will turn on as soon as the temperature of the device decreases.

Find the cause of the overheating.

In the event of a failure of the safety thermostat, overheating of the device will trigger the overheating protection. This will turn the device off completely. In this case, it is recommended to contact the service in order to replace the overheating protection.

Protection against tipping over

The heater is equipped with a tilt switch. The anti-tipping device is a safety device that prevents fire in the event of the appliance toppling over. The device switches itself off in the event of tipping from vertical position, e.g. due to overturning.

The tilt switch turns the device off when tilted from the vertical position. After placing it back on a hard and flat surface, the device can be switched on again after a few seconds.

Device information

Device description

The HH-1001/1002/1011 oil heater is designed for heating and distributing warm air, e.g. inside rooms.

The heat electrically generated by the heating elements within the device is absorbed by the heating medium oil. The heating medium oil offers the advantages of quick heat-up and long-term heat storage capacity. On these grounds the heating medium oil can guarantee a continuous heat emission. The radiator's fins increase the heat radiating sudace and so enhance its effectiveness. The device is fuffher equipped with an overheating protection and a tilt protection.

Device view

1. Switches
2. Thermostat knob
3. Cable holder
4. Radiator ribs
5. Wheels

Transport and storage

Tip

Incorrect storage or transport of the device may damage it. Observe the information on transport and storage of the device.

Transport

Each time before transport, consider the following tips:

• Turn off the device.
• Disconnect the device by pulling the power plug.
• Do not use the power cord to pull the device.
• Wait for the device to cool down.

Storage

Before each storage, follow the instructions below:

• Disconnect the device by pulling the power plug.
• Wait for the device to cool down.

When the device is not being used, observe the following recommendations regarding storage conditions:

• protect it from moisture, frost and heat,
• store the device in an upright position in place free from dust or direct sunlight,
• if necessary, protect the device from dust using appropriate packaging,
• do not place other devices or on top of the device items in order to avoid its damage.

Installation and commissioning

Before using the unit, install the feet/wheels that are included separately in the box.

Warning!

Do not turn on the unit without wheels installed. The heater will only operate in the upright position. Any other position will cause damage to the unit. It may also lead to fire!

Kit contents

• 1x Oil heater
• 2x Mounting base
  • 2x Yoke bolt with wing nuts
• 4x Wheels
• 1x User manual

Unpacking the device

1. Open the carton and take out the device.
2. Completely remove the device and parts from its packaging.
3. Completely unwind the power cord. Note, that the cord is not damaged and avoid damaging it while unwinding it.

Assembly

1. Place the heater upside down on a surface that will not cause scratches. Make sure the unit is stable and will not tip over.
2. Remove the nut from the caster and then secure the

fig.

caster bolt in the hole in the mounting base. Screw the nut back on and repeat for the caster on the other side.

1. Remove the wing nuts from the yoke bolt (fig. 1), attach it between the first and second ribs of the heater (as seen from the front of the unit - fig. 2).
2. To fix the caster mounting base to the radiator, insert the yoke screw into the holes located on the base (fig. 3).
3. Position the mounting base perpendicular to the heater ribs. Screw the wing nuts to the yoke bolt. Important: do not over tighten the nuts as this may damage the heater.
4. To mount the rear wheels, repeat steps 2, 3, 4 and 5. Remember to mount the rear wheels between the last two ribs of the heater.

Commissioning the device

Information

An unusual smell may arise when using the appliance for the first time or after a long period of non-use.

When positioning the device, follow the guidelines regarding the minimum distance to other objects, specified in the chapter „Technical appendix”.

• Before restarting the device, check the condition of the power cord. In case of any doubts regarding its condition, we recommend contacting the service.
• Place the device in an upright position on a stable, level surface, resistant to increased temperatures.
• Check that curtains and other objects do not obstruct the air flow.
• Especially when setting up the device in the center of the room, avoid placing the power cord or extension cord in such a way that it may tip over. Use masking plates and cable bridges.
• Check that the extension cords used are fully extended.
• Do not place the device directly below a power socket.
• Make sure that the device does not come into contact with moisture or water.

Operation

Avoid leaving doors and windows open.

Control panel

1. Switch / selection of the heating power (I)
2. Switch / selection of the heating power (II)
3. Thermostat knob

	HH-1001 HH-1011 HH-1002
Switch I 600 W 800	W 1000 W
Switch II 900 W 1200	W 1500 W
Switch I+II 1500 W	2000 W 2500 W

Turning on the device

1. Connect the unit to the power supply.
2. Turn the thermostat knob clockwise to the MAX position and turn on the heater as follows to the MAX position and turn on the heater as follows:
3. Switch I - for low heating power
4. Switch II - for medium heat output
5. Both switches at the same time - for high heating power

→ When the power switch (1 or 2) is in the ON position, it will be illuminated with an indicator light.

Setting the heating level

Information

Choose a lower power when operating the device, e.g. in a small room. If the power is insufficient, set a higher level.

• Set the power switch (1) to position I.
  → The device operates at low power.
• Set the power switch (2) to position II.
  → The device operates at medium power.
• To obtain the maximum heat output, set the both power switch (1+2) to position I+II = III.
  → The device operates at high power.

Optimum thermostat setting

Turn the thermostat knob to the maximum position (clockwise). After obtaining the appropriate temperature in the room, turn the thermostat slowly (counterclockwise) until the device turns off. This way the thermostat will keep the set temperature. When the temperature drops below the set value, the device starts up. When the set value is exceeded, heating are turned off. The device has a built-in fuse to protect the device from overheating. The fuse will turn the device off for a while. In this case, disconnect the device and wait for a few minutes. After this time, heating can be continued.

Decommissioning

Warning against electric voltage

Do not touch the mains plug with wet or damp hands.

• Set the thermostat knob (3) to the minimum position.
• Set the power switches (1+2) to position 0.
• Disconnect the device by pulling the power plug.
• Wait for the device to cool down completely.
• Clean the device as described in the chapter „Maintenance”.
• Store the device in accordance with the chapter „Transport and storage”.

Errors and faults

Warning against electric voltage

Activities that require opening the device may only be performed by an authorized service center or by Mirpol.

The correct operation of the device has been checked many times as part of the production process. If there are any faults, check the list below:

The device makes noises after switch-on:

- As the medium oil heats up, it expands in volume, which causes a noise - this is a normal process and no action is required.

The device does not start up:

• Check the mains connection.
• Check that the mains plug or cord is not damaged.
• Check the electrical fuses on the side power.
• Check the room temperature. Thermostat turned off the device after reaching the set temperature in the room.
• Make sure the device is standing upright on a flat surface. Ev. the protection against overturning was triggered by tilting the device. Always place the device on a suitable and completely flat surface.
• The room thermostat may be defective. Have the damaged thermostat replaced by a qualified service center. Overheating protection has tripped. Have the electrical inspection and overheating protection replaced by an electrical service center or by Mirpol.
• Wait 10 minutes before restarting the device. If the device does not start to work, have the electrical system inspected in a qualified service or Mirpol company.

The device is turned on but the air temperature is not increased:

• Check if heating mode is set.
• Check the room temperature. Thermostat turned off the device after reaching the set temperature in the room.
• Check that it has not started up overheating protection (see chapter „Security”).
• The heating element may have burned out. Have a replacement damaged heating element in a qualified service.
• The room thermostat may be defective. Have a replacement damaged thermostat in a qualified service center.

Tip

Wait at least 3 minutes after completing all maintenance and repair operations. Only turn on the device again after this time has elapsed.

The device does not work properly despite carrying out all the checks:

Contact service. Deliver the device for repair to an authorized Mirpol service center.

Maintenance

Activities before starting maintenance

Warning against electric voltage

Do not touch the mains plug with wet or damp hands.

Turn the both power switch to the „0” (OFF) position, disconnect the power supply and allow the device to cool down.

Warning against electric voltage

Activities that require opening the device may only be performed by an authorized service center or by Mirpol.

Note

The heater is filled with the heating medium oil. Tasks which require the oil tank to be opened must only by carried out by an authorized service center or by Mirpol.

Warning against electric voltage

Never submerge the device in water!

Wipe the surface with a soft cloth. Do not use detergents or agents that may scratch the surface.

Protect electrical components from moisture.

Allow the surface of the heater to dry completely before restarting.

Technical annex

Technical data

Parameter Value
Model HH-1001 HH-1011 HH-1002
Heating powerGrade 1Grade 2Grade 3	600 W900 W1500 W	800 W1200 W2000 W	1000 W1500 W2500 W
Supply current 220-240V, 50-60Hz 220-240V, 50-60Hz 220-240V, 50-60Hz
Heating ribs 7 9 11
Maximum power consumption 1500 W 2000 W 2500 W
Nominal current consumption 6,5 A 8,7 A 109 A
Plug type	CEE 7/7	CEE 7/7	CEE 7/7
Cable length	1,8 m	1,8 m	1,8 m
Weight	6 kg	7,2 kg	13 kg
Dimensions (length x width x height)	33,5 x 24 x 55 cm	40 x 24 x 55 cm	48,7 x 24 x 55 cm
Minimum distance from walls / objectsA: topB: backC: sidesD: front	100 cm100 cm100 cm100 cm	100 cm100 cm100 cm100 cm	100 cm100 cm100 cm100 cm

DISPOSAL OF APPLIANCES AND BATTERIES

After the implementation of the European Directive 2002/96/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that

a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.

Heating medium oil

The heating medium oil must be drained from the device and collected. The heating medium oil is to be disposed of according to the national regulations.

Data on electrical equipment located in individual rooms.

Model identifier (s): HH-1001, HH-1002, HH-1011
Parameter Designation Value Unit Parameter Unit
Thermal power				Type of heat supply only for electric storage local space heaters (one option must be selected)
Nominal thermal power P	nom	0.7001/0.8274/0.9003 kW	W Manual heat supply controller with built-in thermostat no
Minimum thermal power (indicative)	Pmin	0 kW		Manual controller for heat supply with temperature measurement in the room or outside	no
Maximum constant thermal power	Pmax, c	0.7001/0.8274/0.9003 kW		Electronic controller for heat supply with temperature measurement in the room or outside	no
Electricity consumption for own needs Fan-regulated heat output no
At nominal heat output	elmax	ND	kW	Type of heat output / room temperature control (one option must be selected)
At minimum heat output	elmin	ND	kW	Single-stage heat output without room temperature control	no
In standby mode	elsB	ND	kW	Two or more manual steps without room temperature control	no
				Mechanical regulation of the room temperature with a thermostat	yes
				Electronic room temperature control	no
				Electronic room temperature control with a daily controller	no
				Electronic room temperature control with a weekly timer	no
				Other adjustment options (multiple selections possible)
				Room temperature control with presence detection	no
				Room temperature control with open window detection	no
				With distance adjustment	no
				With adaptive start control	no
				With reduced working hours	no
				With radiant heat sensor	no
Contact details				Mirpol sp. z o.o., ul. Ciasna 3, 35-232 Rzeszów, [e-mail]