CDF322T-86S - Dishwasher CANDY - Free user manual and instructions

Product Type	Dishwasher
Brand	Candy
Model	CDF322T-86S
Dimensions (H x W x D)	820 x 600 x 600 mm (approx)
Height Adjustable	820 - 885 mm
Capacity	12 place settings
Water Connection	Cold or hot water up to 60 °C
Water Pressure	0.08 - 0.8 MPa
Electrical Supply	220-240 V, 50/60 Hz
Water Softener Settings	5 levels (0-4)
Salt Container Capacity	1.5 - 1.8 kg
Rinse Aid Dispenser	Yes, adjustable 1-6 (recommended 4)
Detergent Dispenser	20-30 g for main wash, 8 g for pre-wash
Filter System	Three-part: central container, flat gauze, micro filter
Spray Arms	Upper and lower rotor arms (removable)
Interior Material	Stainless steel
Half Load Function	Yes (upper or lower basket)
Adjustable Upper Basket	Yes, two positions (low and high)
Cutlery Basket	Detachable two-part basket
Safety Features	Door safety switch, auto shut-off when door opened
Installation	Under counter or free-standing, adjustable feet
Weight	Approx. 45 kg (estimation)

Frequently Asked Questions - CDF322T-86S CANDY

How do I adjust the water softener setting?

Remove the lower rack, unscrew the cap of the salt dispenser, and turn the selector screw to the required position using a screwdriver or knife. Refer to the hardness table in the manual.

How do I load salt into the dishwasher?

Unscrew the cap of the salt container located at the bottom of the tub. Fill with dishwasher-specific salt until full. Some water may overflow. Clean the thread and retighten the cap. Run a rinse cycle afterward.

How do I fill the rinse aid dispenser?

Locate the rinse aid dispenser to the left of the detergent dispenser. Push the reference mark and pull the tab to open. Fill with rinse aid until the indicator eye is dark. Close the lid. Adjust the dosage (1-6) using a coin under the lid.

How often should I clean the filters?

Check and clean the filters after each wash. Remove the filter unit by turning the handle anticlockwise. Wash the central container, gauze, and micro filter under running water. Reassemble correctly and screw back clockwise.

What type of detergent should I use?

Use detergent specifically designed for dishwashers (powder, liquid, or tablets). Avoid hand-washing detergents. 'FINISH' gives good results. Follow the dosage instructions on the detergent packaging.

Why are my dishes not drying completely?

Ensure the rinse aid is filled and the setting is adequate (recommended 4). Leave the door ajar after the cycle to improve air circulation. Check that the rinse aid dispenser is not empty.

Why are there white spots on my dishes?

White spots indicate hard water. Check the salt level and water softener setting. Adjust the rinse aid dosage. If the problem persists, increase the softener setting or contact service.

How do I adjust the upper basket to a higher position?

For Type A: turn front stops outward, remove basket, remount in upper position, and replace stops. For Type B: pull out basket, grasp both sides, lift upwards. Dishes over 20 cm cannot be loaded in upper basket when raised.

What should I do if the dishwasher doesn't start?

Check that the plug is connected, the door is closed, the On/Off button is pressed, and the water tap is open. Ensure the programme selector is correctly positioned. Check the fuse and electricity supply.

Can I install the dishwasher under a counter?

Yes, the dishwasher is designed for under-counter installation. The standard height is 82 cm (adjustable up to 88.5 cm). Use the provided self-adhesive tape if the worktop underside is water-absorbent. Secure with 30 mm screws.

USER MANUAL CDF322T-86S CANDY

DISHWASHER

DISHWASHER

DISHWASHER

DISHWASHER

DISHWASHER

CONTENTS

Salt refill indicator

Cutlery basket (fig. 4)

Lower basket (fig. 6)

M = 8 + 4 deep plates N = 11 + 1 flat plates O = 12 dessert plates P = serving dish Q = cutlery basket

Cutlery basket (fig. 7)

1/2 mixed load (fig. 1) A = glasses B = cups C = deep plates D = dessert plates E = saucers F = saucepan G = roasting pan H = medium bowl I = small bowl

1/2 standard load (fig. 2) A = 6 glasses B = 6 cups C = serving dish D = 6 deep plates E = 6 dinner plates F = 6 dessert plates G = 6 saucers H = medium bowl I = small bowl

Place cutlery in the cutlery basket in the lower basket.

Half load in the lower basket

Lower basket (fig. 3)

A = Medium saucepan B = Large saucepan C = Frying pan D = Lid E = Tureen and serving dish F = Cutlery G = Ovenproof dishes

Lower basket (fig. 4)

M = 8 + 4 Deep plates N = 11 + 1 Flat plates O = 12 Dessert plates P = Serving dish Q = Cutlery basket

FILLING WITH DETERGENT AND RINSE AID

Filling with soap

IMPORTANT

CLEANING THE FILTER

The filter unit (fig. A "4") consists of:

GOOD ADVICE

Fig. 1

Lower basket (fig. 3)

A = medium saucepan B = large saucepan C = frying pan D = lid E = serving dish F = cutlery G = ovenproof dishes

Cutlery basket (fig. 4)

Lower basket (fig. 6)

M = 8 + 4 soup plates N = 11 + 1 main course plates O = 12 dessert plates P = serving platter Q = cutlery

Cutlery basket (fig. 7)

H = bowl, medium I = bowl, small

1 = bowl, item

1/2 Standard load (fig. 2)

A = 6 glasses

B = 6 cups

H = bowl, tea I = bowl, small

Cutlery is placed in the cutlery basket in the lower basket

Half load in the lower basket

(Only in certain models)

Lower basket (fig. 3)

A = medium-sized saucepan

B = large saucepan

C = frying pan

D = 1 ock

F = loading tray

Lower basket (fig. 4)

CLEANING THE FILTERS

The filter system (fig. A "4") consists of:

GENERAL ADVICE

WHEN THE PROGRAM IS FINISHED

Adjusting the upper basket

(only in some models)

Lower basket (fig. 3)

Lower basket (fig. 6)

Lower basket (fig. 3)

A = Medium-sized pot

B = Large pot

C = Frying pan

D = Kannet

CLEANING THE FILTER

GENERAL INSTRUCTIONS

AFTER WASHING

INSTALLATION UNDER AN EXISTING COUNTERTOP

■ The height of the washing machine ("A" in fig. 1) is 82 cm, which is a standard from the International Regulation (ISO) so that the machine fits under the kitchen counter. ■ If the underside of the countertop is made of water-absorbing material, attach the self-adhesive tape supplied with the machine to the underside of the countertop at the front, above the door opening of the machine (fig. 2). - Then place the machine in position and connect the water hoses according to the instructions (fig. 1). The front legs of the machine can be adjusted so that it is level. ■ Then secure the machine to the countertop using the 30 mm long screws "A" as shown in fig. 4.

INSTALLATION UNDER AN EXISTING COUNTERTOP

(Dishwashers with adjustable legs)

Salt indicator

A = Soup plates B = Dinner plates C = Dessert plates D = Bowls E = Cups F = Glasses

Upper basket (fig. 2)

Lower basket (fig. 3)

Lower basket (fig. 6)

M = 8 + 4 soup plates N = 11 + 1 dinner plates O = 12 dessert plates P = Serving dishes Q = Cutlery

Cutlery basket (fig. 7)

1/2 mixed wash (fig. 1)

A = Glass

B = Cups

C = Dinner plates

D = Dessert plates

E = Saucers

E - saucers E - casserole

F = Casserole

G = Frying pan

H = Medium bowl

I = Small bowl

1/2 standard wash (fig. 2)

A = 6 glasses

B = 6 cups

C = Serving dish

Lower basket (fig. 3)

E = Terrines, serving dishes

F = Cutlery

G = Ovenproof dishes

Lower basket (fig. 4)

M = 8 + 4 soup plates

N = 11 + 1 dinner plates

O = 12 dessert plates

P = Serving dishes

Q = Cutlery

FILLING WITH DETERGENT AND RINSE AID

Since not all types of detergent are the same, also read the instructions on the package.

CLEANING THE FILTER

PRACTICAL TIPS

Please read the instructions in this booklet carefully because they contain important information on how to install, use and maintain your dishwasher safely as well as containing useful tips on how to make the most of it.

Keep this booklet safe for future reference.

SAFETY INSTRUCTIONS

There are certain basic safety rules which are valid for any domestic appliance.

Installation

■ Make sure that the plug fitted to the machine is compatible with the power supply socket. If it is not, get a suitably qualified person to fit the correct type, and to make sure that the cables to the mains socket are able to cope with the power rating of the appliance. ■ Ensure that the dishwasher does not crush power cables. ■ In general it is not advisable to use adaptors, multiple plugs and/or extension cables. ■ Should it be necessary to replace the supply cord, call the After Sales Service Centre.

Safety

■ Never touch the appliance when your hands or feet are wet or damp. ■ Do not use when your feet are bare. ■ Do not remove the plug from the mains supply socket by pulling the mains cable or the machine itself. ■ Do not leave the appliance exposed to the elements (rain, sun etc). ■ Do not let children (or others incapable of operating it) use the machine without supervision. ■ Water left in the machine or on the dishes at the end of the wash programme should not be swallowed. ■ The door should not be left in the open position since this could present a potential hazard (e.g. tripping). ■ Leaning or sitting on the open door of the dishwasher could cause it to tip over.

WARNING!

Knives and other utensils with sharp points must be loaded in the basket with their points down or placed in a horizontal position.

Daily use

■ This appliance is designed for domestic use only. ■ The dishwasher is designed for normal kitchen utensils. Objects that have been contaminated by petrol, paint, traces of steel or iron, corrosive chemicals, acids or alkalis must not be washed in the dishwasher. ■ If there is a water softening device installed in the home there is no need to add salt to the water softener fitted in the dishwasher.

■ Cutlery is washed best if it is placed in the basket with the handles downwards.

If the appliance breaks down or stops working properly, switch it off, turn off the water supply and do not tamper with it. Repair work should only be carried out by an approved service agent and only genuine spare parts should be fitted. Any failure to follow the above advice may have serious consequences for the safety of the appliance.

Disposal

■ The dishwasher has been made from materials which can be recycled so that it can be disposed of in an environmentally friendly way. ■ If you wish to dispose of an old dishwasher be careful to remove the door to eliminate the risk of children becoming trapped inside it.

INSTALLATION

(Technical notes)

■ After unpacking, adjust the height of the dishwasher. For the dishwasher to work correctly it must be level. Adjust the feet so that the machine does not tilt by more than 2 degrees. ■ If you need to move the machine after removing the packaging, do not try to lift it by the bottom of the door. Follow the instructions in the figure below. Open the door slightly and lift the machine by holding on the top.

IMPORTANT

When the appliance is located on a carpet floor, attention must be paid to ensure that there is no obstruction to the bottom vents.

Make sure that the plug on the appliance remains accessible after installation.

Electrical connection

This appliance complies with international safety standards, and is fitted with a 3 pin plug with earth connection to ensure complete earthing of the product. Before connecting the appliance to the mains supply it is important to ensure:

1. that the supply socket is properly earthed;
2. that your electricity supply is capable of meeting the consumption requirements listed on the rating plate of your appliance.

WARNING!

Ensure that your product is properly earthed.

In the absence of adequate earthing you will notice that when touching the metal parts of your appliance an electrical dispersion can be felt, due to the presence of a radio interference suppressor.

Manufacturer declines all responsibility for any damage due to non-earthing of the machine.

This appliance complies with Directives 89/336/EEC, 73/23/EEC and following changes.

Water connection

IMPORTANT

The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused.

The inlet and drain hoses can be directed to left or right.

IMPORTANT

The dishwasher can be connected to either cold or hot water, as long as it is no hotter than 60 °C.

Water pressure must be between 0.08 MPa and 0.8 MPa. If the pressure is below the minimum, consult our service department for advice. The inlet hose must be connected to a tap so that the water supply can be cut off when the machine is not in use (fig. 1 B). The dishwasher is fitted with a 3/4" threaded connector (fig. 2). Connect inlet hose "A" to water tap "B" with a 3/4" attachment, making sure that it has been properly tightened. If necessary, the inlet pipe can be lengthened up to 2.5 m. The extension pipe is available from the After Sales Service Centre. If limescale deposits or sand are present in the water, it is advisable to obtain the appropriate filter, art. 92643345-92643394, from the After Sales Service Centre (fig. 3). The filter "D" must be inserted between the tap "B" and the inlet hose "A", remembering to fit the washer "C". If the dishwasher is connected to new pipes or to pipes which have not been in use for a long time, run water through for a few minutes before connecting the inlet hose. In this way, no deposits of sand or rust will clog up the water inflow filter.

Connecting the outlet hose

The outlet hose should discharge into a standpipe, making sure that there are no kinks (fig. 4). The standpipe must be at least 40 cm above floor level and it must have an internal diameter of at least 4 cm. It is advisable to fit an anti-odour air trap (fig. 4X). If necessary, the outlet hose can be extended up to 2.5 m, provided that it is kept at a maximum height of 85 cm above floor level. The extension pipe is available from the After Sales Service Centre.

The hose can be hooked over the side of the sink, but it must not be immersed in water, in order to prevent water from being syphoned back to the machine when this is in operation (fig. 4Y). When installing the appliance under a worktop, the hose pipe clamp must be attached to the wall in the highest possible position under the worktop (fig. 4Z). Check that there are no kinks in the inlet and outlet hoses.

INSTALLATION IN FITTED KITCHENS

The height of the dishwasher ("A" in fig. 1) is 82 cm, as scheduled by the international Regulations (ISO), and the dishwasher will fit perfectly under the kitchen working top. If the underside of the worktop is of water absorbent material (e.g. unfaced chipboard), affix the self adhesive protective tape to it (fig. 2). Insert the dishwasher under the worktop and connect to the electricity and water supplies as shown in the instruction book (fig. 1). The front feet can be adjusted so that correct height is reached. Tighten the dishwasher to the worktop by means of the 30 mm long screws "A" shown in fig. 3.

INSTALLATION IN FITTED KITCHENS

(Dishwasher with adjustable feet)

■ Adjust the height of the dishwasher according to the available space "A" of fig. 1 (maximum 885 mm). ■ Ensure that the appliance is quite level by adjustment of the rear feet (fig. 4). ■ If the underside of the worktop is of water absorbent material (e.g. unfaced chipboard) affix the self adhesive protective tape to it (fig. 2). ■ Insert the dishwasher under the worktop and connect to the electricity and water supplies as shown in the instruction book (fig. 1). ■ If necessary, final height adjustment can be achieved via the front feet and locked by the fitted locking nuts. ■ Tighten the dishwasher to the worktop by means of the 30 mm long screws "A" shown in fig. 3.

The plinth is adjustable to allow perfect cover of the bottom gap.

Opening the door

Put your hand into the recess and pull. If the machine comes open while it is working, an electrical safety device automatically switches everything off.

IMPORTANT

For the machine to work properly, the door should not be opened while it is in operation.

Closing the door

Place the baskets in the machine. Make sure that both the spray arms are free to rotate and are not obstructed by cutlery, crockery or pans. Close the door, pressing on it to make sure it is firmly shut.

WATER SOFTENER UNIT

Depending on the source of the supply, water contains varying amounts of limestone and minerals which are deposited on the dishes leaving whitish stains and marks.

The higher the level of these minerals present in the water, the harder the water is. The dishwasher is fitted with a water softener unit which, through the use of special regenerating salt, supplies softened water for washing the dishes. The softener unit can treat water with a hardness of up to 60°FH (French grading) or 33°FH (German grading) through five different settings.

The degree of hardness of your water can be obtained from your water supply company.

Regulating the water softener

The table below lists different degrees of water hardness with the corresponding setting for the softener unit.

*The water softener unit is set in the factory at level 2, as this is suitable for the majority of users.

If your water is at level 0, you need not use any regenerating salt, nor need you make any adjustment, as your water is soft.

According to the degree of hardness of your water, regulate the softener unit in the following way:

1. remove the lower rack. Unscrew and remove the cap from the salt dispenser located in the bottom of the tub (fig. A"1");
2. turn the selector screw to the required position with a screwdriver or a knife.

N.B.: For models fitted with electronic programmer refer to the programme list enclosed.

Level	Water hardness	Water hardness	Use of regenerating salt	Water softener setting	N° of washes
	°FH (French)	°dH (German)
0	0-9	0-5	NO	FREE
1	10-30	6-16	YES	position N.1	50
*2	31-40	17-22	YES	position N.2	40
3	41-50	23-27	YES	position N.3	30
4	51-60	28-33	YES	position N.4	20

Loading the salt

■ On the bottom of the machine there is a container for the salt for regenerating the softener. ■ It is important to use only a salt that is specifically designed for dishwasher. Other types of salt contain small quantities of insoluble particles which over a long period of time may affect and deteriorate the softener performance. ■ To add salt, unscrew the cap of the container on the bottom and then refill the container. ■ During this operation a little water will overflow: but keep adding salt until the container is full. When the container is full, clean the thread of salt residue and retighten the tap. ■ After loading the salt, it is recommended running a complete washing cycle, or COLD RINSE programme. The salt dispenser has a capacity of between 1.5 and 1.8 kg and, for efficient use of the appliance, it should be refilled from time to time according to the regulation of the water softener unit.

IMPORTANT

(Only for first start up)

When the appliance is used for the first time, after completely filling the salt container, it is necessary to add water until the container overflows.

Salt loading indicator

Some models are provided with an indicator light which signals salt consumption.

The signal will appear according to one of two systems:

■ an indicator light on the control panel which will light up when it is necessary to reload the salt container; ■ the salt container cap with a green mobile light (fig. 1a) which remains visible as long as there is enough salt for regeneration purposes. When the green surface is depressed inside the cap, more salt must be loaded.

Other models are provided with a blind cap (fig. 1b). In this case, the salt level must be checked periodically, according to the regulation of the water softener unit.

IMPORTANT

The appearance of white stains on dishes is generally an important sign that the salt container needs filling.

Fig. 1

Adjustment of the upper basket

(some models only)

If 27 cm to 31 cm plates are normally used, load them onto the lower basket after the upper basket has been placed in its upper position and proceed as detailed below (According to the models):

Type "A":

1. Turn the front stops "A" outwards;
2. Take out the basket and remount it in the upper position;
3. Replace the blocks "A" in their original position.

Dishes that are bigger than 20 cm in diameter can no longer be loaded onto the upper basket and the mobile supports cannot be used when the basket is in the upper position.

Type "A"

Type "B":

1. Pull out the upper basket;
2. Then grasp the basket from both sides and lift it upwards (fig. 1).

Dishes that are bigger than 20 cm in diameter can no longer be loaded onto the upper basket and the mobile supports cannot be used when the basket is in the upper position.

ADJUST BASKET TO THE LOWER POSITION:

1. Grasp the basket from both sides and lift slightly upwards (fig. 2a);
2. Then slowly release into the correct position (fig. 2b).

It is advisable to adjust the basket before loading the dishes.

Type "B"

LOADING DISHES

Using the upper basket

■ The upper basket is provided with mobile racks hooked to the sides of the basket which can be regulated in two positions: upright and lowered. In the lowered position the racks may be used for tea and coffee cups, kitchen knives and ladles. Glasses with stems may be safely hung on the ends of the racks. Glasses, cups, saucers and dessert plates may be loaded under the racks. ■ Soup plates and ordinary plates may be loaded with the rack in the upright position. Plates should be loaded vertically with the underside of the plate towards the back of the dishwasher with a space between each plate to allow water to pass freely. ■ It is advisable to load plates of the same size together in order to utilize maximum basket capacity. ■ Plates may be loaded in a single row (fig. 1) or on both rows (fig. 2). ■ It is advisable to load large plates (approx. 27 or more cm) slightly tilted towards the rear to facilitate introduction of the basket into the machine.

■ Salad bowls and plastic bowls may also be loaded on the upper basket. It is advisable to block these in place so that the jets of water do not make them overturn. ■ The upper basket has been designed to offer maximum flexibility in use and can be loaded with up to 24 plates on two rows, up to 30 glasses on five rows or a mixed load.

Using the lower basket

■ Saucepans, oven dishes, tureens, salad bowls, lids, serving dishes, dinner plates, soup plates and ladles can be loaded on the lower basket. ■ Place the cutlery in the plastic cutlery holder with the handles pointing upwards. ■ Place the cutlery holder on the lower basket (fig. 3), making sure that the cutlery does not get in the way of the rotating arms.

IMPORTANT

The lower basket has a safety-stop device, for its safe extraction, also especially useful with a full load. For loading salt, cleaning filter and for ordinary maintenance, the complete extraction of the basket is necessary.

A standard daily load is represented in figs. 1, 2 and 3.

Upper basket (fig. 1)

A = soup plates B = dinner plates C = dessert plates D = saucers E = cups F = glasses

Upper basket (fig. 2)

A = soup plates B = dinner plate C = dessert plates D = saucers E = cups F = glasses with stems G = glasses H = single section cutlery basket

Lower basket (fig. 3)

A = medium-sized saucepan B = large saucepan C = frying pan D = lids E = tureens, serving dishes F = cutlery G = oven dishes

Please load the dishwasher sensibly to ensure the best wash results.

Cutlery basket (fig. 4)

The cutlery basket is made with two detachable parts which will enable various loading options. The two parts can be detached by sliding the left section away from the right section.

INFORMATION FOR THE TEST LABORATORIES

General programme comparison (Ref. EN 50242 Standards)

(see programmes selection)

1. Upper basket position: low
2. Normal load
3. Shine setting: 6
4. Amount of detergent:

- 8 g for pre-wash;

- 22 g for wash.

12 international place load (Ref. EN 50242)

Correct loading is indicated, in fig. 5 for the upper basket, in fig. 6 for the lower basket and in fig. 7 for the cutlery basket.

Lower basket (fig. 6)

M = 8 + 4 soup plates N = 11 + 1 dinner plates O = 12 dessert plates P = serving dish Q = cutlery

Cutlery basket (fig. 7)

Place the side racks in the lower position and fill with 6 + 6 knives (R); in the spaces left insert cutlery with the handles down. Take care not to load more than two different types of cutlery in the same compartment.

Half load wash upper basket

(some models only)

1/2 mixed load (fig. 1)

A = glasses

B = cups

C = soup plates

D = dessert plates

E = saucers

F = saucepan

G = frying pan

H = medium bowl

I = small bowl

1/2 load standard (fig. 2)

A = 6 glasses

B = 6 cups

C = serving dish

D = 6 soup plates

E = 6 dinner plates

F = 6 dessert plates

G = 6 saucers

H = medium bowl

I = small bowl

Place the cutlery in the plastic cutlery holder on the lower basket.

Half load wash lower basket

(some models only)

Lower basket (fig. 3)

A = medium-sized saucepan

B = large saucepan

C = frying pan

D = lids

E = tureens, serving dishes

F = cutlery

G = oven dishes

Please load the dishwasher sensibly to ensure the best wash results.

Lower basket (fig. 4)

M = 8 + 4 soup plates

N = 11 + 1 dinner plates

O = 12 dessert plates

P = serving dish

Q = cutlery

LOADING THE DETERGENT AND THE RINSE AID

Filling the detergent container

IMPORTANT

It is essential to use a detergent that is specifically designed for dishwashers either in powder, liquid or tablet form.

“FINISH” gives very good results and can be easily obtained.

Unsuitable detergents (like those for washing up by hand) do not contain the proper ingredients for use in a dishwasher, and stop the dishwasher from working correctly.

Normal wash

The detergent container is inside the door (fig. A "2"). If the lid of the container is closed, press the button (A) to open.

At the end of every wash cycle the lid is always open and ready for the next time the dishwasher is used.

WARNING!

When loading the lower basket, please ensure that the plates or others do not obstruct the detergent dispenser.

The amount of detergent to be used varies according to how dirty the dishes are and on the type of dishes to be washed. We advise using 20:30 g of detergent in the wash section of detergent compartment (B).

After pouring the detergent into the container, close the lid, firstly pushing (1) and then pressing on it (2) until you hear the click.

Since not all detergents are the same the instructions on the boxes of detergent can vary. We should just like to remind users that too little detergent does not clean the dishes properly whilst too much detergent will not produce better results and is also a waste.

IMPORTANT

Do not use an excessive amount of detergent and help limit damage to the environment at the same time.

CAUTION!

IMPORTANT NOTE ON THE USE OF COMBINED DETERGENTS

If you are planning to use combined detergents i.e. those with built in salt and/or rinse agent, we would advise the following:

■ read carefully and follow the manufacturer's instructions given on the packaging:

Some combined detergents, particularly those with built-in rinse agents, provide best results when used with specific programmes:

The effectiveness of detergents containing built-in water softener/salt depends on the hardness of your water supply. Check that the hardness of your water supply is within the effective range given on the detergent packaging. In certain circumstances, use of combined detergents can cause: ■ limescale deposits on dishes or in the dishwasher; ■ a reduction in washing and drying performance.

Should this occur, we would recommend using traditional separate products – salt, detergent, and rinse agent. This will ensure that the water softener in the dishwasher operates correctly.

Please note that on return to the use of conventional salt, a number of cycles will be required before the system becomes fully efficient again.

IMPORTANT

Any problems which arise as a direct result of the use of these products are not covered by our warranty.

Filling the rinse aid container

The rinse aid, which is automatically released during the last rinsing cycle, helps the dishes to dry quickly and prevents spots and stains forming.

The rinse aid container can be found to the left of the detergent container (fig. A "3").

To open the lid, push the reference mark and, at the same time, pull the tab of opening.

It is always advisable to use rinse aid that is specifically designed for dishwashers.

Check the rinse aid level through the indicator eye (C) which is located on the dispenser.

Regulating the rinse aid from 1 to 6

The regulator (D) is placed under the lid and can be turned using a coin.

The recommended position is 4. The limestone content of the water considerably affects the formation of limescale and the drying performance.

It is therefore important to regulate the quantity of rinse aid to achieve good washing results.

If, after the wash, streaks occur on the dishes, decrease the amount by one position. If whitish spots occur, increase the amount by one position.

FULL EMPTY dark

light

CLEANING THE FILTERS

The filter system (fig.A "4") consists of:

a central container that traps the larger particles;

a flat gauze that continuously filters the wash water;

a micro filter, located beneath the gauze, that traps the tiniest particles ensuring a perfect rinse.

■ To achieve excellent results every time, the filters should be checked and cleaned after each wash. ■ To remove the filter unit, simply turn the handle anticlockwise (fig. 1). ■ For ease of cleaning, the central container is removable (fig. 2). ■ Remove the gauze filter (fig.3) and wash the whole unit under a jet of water. If necessary a small brush can be used. ■ With the Self-cleaning Micro filter, maintenance is reduced and the filter unit need only be checked every two weeks. Nevertheless, after each wash it is advisable to check that the central container and the gauze filter are not clogged.

WARNING!

After cleaning the filters, make sure that they are correctly reassembled and that the gauze filter is properly positioned at the bottom of the dishwasher.

Make sure that the filter is screwed back, clockwise, into the gauze, as poor seating of the filter unit could have an adverse effect on the efficiency of the appliance.

IMPORTANT

Never use the dishwasher without the filters.

PRACTICAL HINTS

How to get really good wash results

■ Before placing the dishes in the dishwasher, remove any remaining food (bones, shells, pieces of meat or vegetables, coffee grounds, skin of fruit, cigarette ash, toothpicks, etc.) to avoid blocking the filters, water outlet, and washing arm nozzles. ■ Try not to rinse the dishes before loading them into the dishwasher. ■ If saucepans and oven dishes are encrusted with the remains of burnt or roast food, it is advisable to leave them to soak before washing. ■ Place the dishes face downwards. ■ Try to place the dishes in such a way that they are not touching one another. If they are loaded properly, you will get better results. ■ After loading the dishes, check that the washing arms can rotate freely. ■ Pans and other dishes that have particularly stubborn food particles or remnants of burnt food should be left to soak in water with dishwasher detergent. ■ To wash silver properly:

a) rinse the silver immediately after use, especially if it has been used for mayonnaise, eggs, fish, etc.; b) do not sprinkle detergent onto it; c) keep it separate from other metals.

How to make savings

If you want the dishwasher to give a complete wash, place the dishes in the dishwasher at the end of each meal and, if necessary, turn on the COLD RINSE cycle to soften the food remains and remove bigger particles of food from the new load of dishes. When the dishwasher is full, start the complete wash cycle programme. ■ If the dishes are not very dirty or if the baskets are not very full, select an ECONOMY programme, following the instructions in the program list.

What not to wash

It should be remembered that not all dishes are suitable for washing in a dishwasher. We advise against using the dishwasher to wash items in thermoplastic, cutlery with wooden or plastic handles, saucepans with wooden handles, items in aluminium, crystal, leaded glass unless otherwise stated. ■ Certain decorations may fade. It is therefore a good idea before loading the whole batch to wash just one of the items first so as to be sure that others like it will not fade. ■ It is a good idea not to put silver cutlery with non-stainless steel handles into the dishwasher as there could be a chemical reaction between them.

IMPORTANT

When buying new crockery or cutlery, always make sure that they are suitable for washing in a dishwasher.

Useful hints

■ In order to avoid any dripping from the top rack, remove the lower rack first. ■ If the dishes are to be left in the machine for some time, leave the door ajar to let some air circulate and to improve the drying performance.

CLEANING AND MAINTENANCE

To clean the dishwasher outside, do not use solvents (degreasing action) or abrasives, but only a cloth soaked with water. The dishwasher does not require special maintenance, because the tank is self-cleaning. Regularly wipe the door gasket with a damp cloth to remove any food remains or rinse aid. It is advisable to remove limestone deposits or dirt periodically, by doing an empty wash; pour a glass of vinegar on the bottom of the tank and select the light wash. If, in spite of the routine cleaning of the filters, you notice that the dishes or pans are not properly washed or rinsed, check that all the spray heads on the rotor arms (fig. A "5") are clear.

If they are blocked, clean them in the following way:

1. To remove the upper rotor arm, turn it until it lines up with the stop marked by the arrow (fig. 1b). Push it upwards (fig. 1) and, keeping it pushed in, unscrew it in a clockwise direction (to reassemble it repeat the same operation, but turn it anticlockwise). The lower rotor arm can be removed simply by pulling it upwards (fig. 2);
2. Wash the rotor arms under a jet of water to clear any blockage in the spray heads;
3. When you have finished, refit the rotor arms in the same position, remembering to re-align the arrow and screw into position. Both the door lining and the tank lining are in stainless steel; however, should spots caused by oxidation occur, this is probably due to a high level of iron salts present in the water. The spots can be removed with a mild abrasive agent; never use chlorine based materials, steel wool, etc.

WHEN CYCLE IS FINISHED

After every wash it is essential to turn off water supply and to switch off the machine by pressing the On/Off button to the off position.

If the machine is not going to be used for some time, it is advisable to follow these rules:

1. Do an empty wash with detergent in order to clean the machine of any deposits;
2. Pull out the electric plug;
3. Turn off the water tap;
4. Fill the rinse aid container;
5. Leave the door ajar;
6. Keep the inside of the machine clean;
7. If the machine is left in places where the temperature is below 0°C, any water left inside the pipes may freeze. Wait until the temperature rises above zero and then wait for about 24 hours before starting up the dishwasher.

IDENTIFYING MINOR FAULTS

Should the dishwasher fail to operate, before contacting the Service Centre, make the following checks:

FAULT CAUSE REMEDY
1 - Machine completely dead	Plug is not connected to wall socket	Connect electric plug
	O/I button has not been pressed	Press button
	Door is open	Close door
	No electricity	Check the fuse in the plug and the electricity supply
2 - Machine does not draw water	See causes for no. 1	Check
	Water tap is turned off	Turn water tap on
	Programme selector is not at correct position	Turn programme selector to correct position
	The inlet hose is bent	Eliminate the bends in the hose
	The inlet hose filter is not correctly connected	Clean the filter at the end of the hose
3 - Machine does not discharge water	Filter is dirty	Clean filter
	Outlet hose is kinked	Straighten outlet hose
	The outlet hose extension is not correctly connected	Follow the Instructions for connecting the outlet hose carefully
	The outlet connection on the wall is pointing downwards not upwards	Call a qualified technician
4 - Machine discharges water continuously	Position of outlet hose is too low	Lift outlet hose to at least 40 cm above floor level
5 - Spray arms are not heard to rotate	Excessive amount of detergent	Reduce amount of detergent Use suitable detergent
	Item prevents arms from rotating	Check
	Plate and cup filter very dirty	Clean plate and cup filter
6 - On electronic appliances without a display: one or more LED flashing quickly.	Water inlet tap turned off	Switch off the appliance. Turn on the tap. Re-set the cycle.

FAULT CAUSE REMEDY
7 - Load of dishes is only partially washed	See causes for no. 5	Check
	Bottom of saucepans have not been washed well	Burnt on food remains must be soaked before putting pans in dishwasher
	Edge of saucepans have not been washed well	Reposition saucepans
	Spray arms are partially blocked	Remove spray arms by unscrewing ring nuts clockwise and wash under running water
	The dishes have not been properly loaded	Do not place the dishes too closely together
	The end of the outlet hose is in the water	The end of the outlet hose must not come into contact with the outflow water
	The incorrect amount of detergent has been measured out; the detergent is old and hard	Increase the measure according to how dirty the dishes are and change detergent
	The wash programme is not thorough enough	Choose a more vigorous programme
	The lower basket dishes have not been washed	Depress half load button
8 - Presence of white spots on dishes	Water is too hard	Check salt and rinse aid level and regulate amount.Should the fault persist, Contact Service Centre
9 - Noise during wash	The dishes knock against one another	Re-check loading of dishes in the basket
	The revolving arms knock against the dishes	Again re-check loading
10 -The dishes are not completely dry	Inadequate air flow	Leave the dishwasher door ajar at the end of the wash program to allow the dishes to dry naturally

N.B.: Should any of the situations occur and should the machine give a bad wash performance, it is necessary to remove the deposits from the dishes by hand since the final drying cycle hardens the deposits which a second wash in the machine would not be able to remove.

If the malfunction continues contact a Service Centre quoting the serial number of the dishwasher. This is found on the plaque on the inside of the dishwasher door at the top or on the guarantee. This information will make it possible to take more effective action more quickly.

The manufacturers decline any responsibility for any printing mistakes in this instruction booklet. They also reserve the right to modify their own appliances as necessary without altering the essential characteristics.

The manufacturer declines all responsibility in the event of any printing mistakes in this booklet. The manufacturer also reserves the right to make appropriate modifications to its products without changing the essential characteristics.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

05.09 - 41017317.A - Printed in Italy - Imprimé en Italie