CAS3HV100L - Water Heaters & Boilers Infiniton - Free user manual and instructions

Product Type	Electric Storage Water Heater
Capacity	100 liters
Dimensions (H x W x D)	1000 x 500 x 500 mm
Weight (empty)	35 kg
Weight (full)	135 kg
Power Consumption	2000 W
Voltage / Frequency	230 V / 50 Hz
Energy Efficiency Class	C
Maximum Temperature	75°C
Tank Material	Enameled steel
Insulation	Polyurethane foam
Heating Element	Copper / Stainless steel
Anode	Magnesium (replaceable)
Safety Features	Overheat protection, pressure relief valve, thermal cutoff
Ingress Protection	IP24
Installation	Vertical wall-mounted
Water Connections	1/2 inch BSP
Warranty	2 years
Maintenance	Anode check every 2 years, descaling as needed

Frequently Asked Questions - CAS3HV100L Infiniton

How do I adjust the water temperature?

Turn the thermostat dial on the front panel. The recommended setting is 60°C to prevent bacteria growth and scaling.

Can I install the water heater outdoors?

No, this unit is rated IP24 (splash-proof) but is designed for indoor installation only. Avoid exposure to rain or freezing temperatures.

How often should I replace the magnesium anode?

Every 2 years to prevent tank corrosion. Check annually and replace if heavily eroded.

What do the error codes indicate?

Common codes: E1 (sensor fault), E2 (overheat), E3 (pressure issue). Refer to the manual for full list.

How do I drain the water heater?

Turn off power and water supply. Attach a hose to the drain valve at the bottom, open it, and open a hot water tap for venting.

What is the pressure rating of the safety valve?

The pressure relief valve is set to open at 8 bar (800 kPa). Ensure it is not blocked.

How to save energy with this water heater?

Set temperature to 55-60°C, insulate exposed pipes, and use a timer to heat water during off-peak hours.

Can I use an extension cord?

No, the water heater must be directly connected to a dedicated circuit. Extension cords can overheat and cause fire.

How do I clean the water heater?

Drain the tank and flush with fresh water. For scale removal, use a descaler solution following the manufacturer instructions.

What is the warranty period?

The unit comes with a 2-year warranty against manufacturing defects. Register your product online to extend coverage.

USER MANUAL CAS3HV100L Infiniton

Five white water heaters labeled 'INVESTON' arranged in a row, no text or symbols on the devices themselves.

CAS3HV30L CAS3HV50L CAS3HV80L CAS3HV100L CAS3HV150L
ean: 8436546188834 ean: 8436546188841 ean: 8436546188858 ean: 8436546188865 ean: 8436546188872

Line drawing of a white Infiniton electric heater with control panel and gauge (no text or symbols on body)

Five white electric water heaters labeled 'INVESTON' arranged in a row on a tiled floor, no additional text or symbols visible.

CAS3HV30L CAS3HV50L CAS3HV80L CAS3HV100L CAS3HV150L
ean: 8436546188834 ean: 8436546188841 ean: 8436546188858 ean: 8436546188865 ean: 8436546188872

Before using your new Infiniton product, please read this user manual carefully to learn how to safely and efficiently use the features offered by this device.

Index	English
Safety information	14
Installation	15
How to use	18
Cleaning & Maintenance	19
Troubleshooting	20

The installation of this electric water heater must be carried out by professionally qualified personnel.

Before installing this water heater, check and confirm that the grounding of the power outlet is properly grounded. Otherwise, the electric water heater cannot be installed and used. Do not use extension cords. Improper installation and use of this electric water heater can result in serious injury and property loss.

A	Pressure relief valve
B	Hot water outlet
C	Cold water inlet
D	Screw thread
E	Drain lever
F	Pressure relief orifice

Get the most out of your water heater

Electric water heaters are tanks that generate and accumulate hot water. Its operation is very simple, but in your day to day may appear different problems that you could fix yourself. At Infiniton we help you with that and much more.

Where can I install it?

Before making the purchase, it is important to know where we are going to place the appliance. Generally, it should be close to the bathroom, as we do not want it to lower the temperature of the water as it travels through the pipes to the bathroom.

So the best solution to place it is directly in the bathroom, the closest possible place to the point of use of the hot water (it avoids water temperature losses due to the water flowing through the pipes). In addition, we need an electrical outlet and a water outlet as close as possible. The areas that have an exit to the outside, for example, a terrace, balcony, garage, will decrease the energy efficiency since we will need more electrical energy to reach and maintain the desired temperature, since it is a colder area. It is advisable to insulate the roof, as well as the hot and cold water pipes.

Line drawing of a white Infiniton electric heater with control panel and gauge (no text or symbols on body)

Recommendations for care

When installing an electric water heater we must take into account a series of considerations and care for its correct operation. We will show you a list of measures that you should apply for the care of this appliance:

Do not leave it on if you are going on a trip

If you are going on vacation or on business for several days, turn off the water heater completely...

Check your water system

The general functioning of all the pipes in the house influences the performance of the electric boiler.

That is why we must make sure that the pipes are working properly.

Check the water inlet and outlet

One of the places that can present the most problems in an electric water heater is the water inlet or outlet. Check for leaks that waste water and affect the heating.

Clean the inside of the container

It is advisable to clean the inside of the water tank frequently. To do this we must disconnect it from the electric current and uncover the tank, and then clean it with a damp cloth. All this without using any chemical or corrosive agent.

Pay attention to this user's manual

The most effective way to maintain the good condition of an electric water heater is to follow the manufacturer's instructions. That is why we must study with some attention the user, maintenance and installation manuals.

General security

The water heater is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the heater.

The wall on which the electric water heater is installed must be able to withstand the load of more than twice the heater completely filled with water without warping or cracking. If this is not the case, other reinforcement measures must be taken.

The socket outlet must be reliably grounded. The installation height of the socket must not be less than 1.8m. The rated current of the socket must not be less than 16A. The socket and plug must be kept dry to avoid electrical leakage. If the power cord is damaged, the special power cord supplied by the manufacturer should be used and replaced by professional service personnel.

The maximum inlet water pressure is 0.5MPa; the minimum inlet water pressure is 0.1MPa, which is necessary for proper operation.

When using the heater for the first time (or when using it for the first time after maintenance), the heater cannot be started until it has been completely filled with water. During water filling, at least one of the heater's outlet valves must be opened to evacuate air. This valve can be closed once the heater is completely filled with water.

The pressure relief valve enclosed with the heater should be installed on the cold water inlet of this heater, ensuring that it is not exposed to fogging. Water may flow out of the pressure relief valve, so the outlet pipe should be wide open to the air. To drain the water inside the inner vessel, it can be drained from the pressure relief valve. Loosen the threaded screw of the pressure relief valve and lift the drain lever upwards (see Fig. 1). The drain pipe connected to the pressure relief port must be kept sloped downward and in a frost-free environment. Water may drip from the discharge tube of the pressure relief device and that this tube should be left open to the atmosphere.

During heating, water droplets may fall out of the pressure release orifice of the pressure relief valve, which is a normal phenomenon. The pressure release orifice must not be blocked under any circumstances, otherwise the heater may be damaged, even causing accidents. If a major water leakage occurs, contact the customer service center for repair.

The pressure relief valve should be checked and cleaned regularly, to ensure that it is not blocked.

Since the water temperature inside the heater can reach 75^ C. the hot water should not be exposed to the human body when it is used for the first time. Adjust the water temperature to a suitable temperature to avoid scalding.

If any part or component of this electric water heater is damaged, please contact the customer service center for repair.

Product description

Due to technological innovations, the product description in this manual may not completely match your appliance. More detailed information corresponds to the final product.

1 Thermometer

2 On/Off

3 Power indicator light

4 Hot water outlet

5 Temperature adjustment button

6 Cold water inlet

7 Operation indicator light

8 Internal storage tank

9 Thermal insulation

10 Cover

11 Heating element

12 Anode

Rated voltage 220-240V
Rated frequency 50/60HZ
Rated pressure 0.75MPa
Water temperature 75°C
Water resistance IPX4
Power supply 250V~10A
Rated power 800/1200/2000W
Rated current 3.5/5.2/8.7A
Nominal volume 30L/50L/80L/100L	/120L/150L
Useful heating performance >90%
Type of structure	Hermetically sealed
Fixing mode	Hanging type

Electric diagram

1. This electric water heater must be installed on a strong wall. If the wall cannot support a load equivalent to twice the total weight of the water-filled heater, it will be necessary to install a special support. In case the wall is made of a hollow material, be sure to fill it completely with a layer of cement concrete.

2. After selecting a suitable location, determine the position of the two installation holes used for the extension bolts with hook and drill two holes in the wall with the corresponding depth by using a drill bit with the size matching the expansion bolts connected with the heater, insert the bolts, place the hook upwards, tighten the nuts to fix firmly, and then hang the electric water heater (see Fig.2).

Capacity 30L 50L 80L 100L 120L 150L
L(mm)	Vertical installation 185 185 210 210 210
	Horizontal installation	208	470	327	487	647	856

1. Install the wall outlet. The socket must be 220V. It is recommended to place the socket on the right side, above the heater. The height of the socket to the floor should not be less than 1.8m (see Fig.3). In case of failure of the power cord, it must be replaced by the manufacturer, a service technician or a qualified person to ensure safety.

1. If the bathroom is too small, the heater can be installed elsewhere. However, in order to reduce heat losses from the piping, the place of installation of the heater should be as close to the heater as possible.

PIPING CONNECTION

1. Pipe sizes should be G1/2"; Maximum inlet pressure should be expressed in Pa; Minimum inlet pressure should be expressed in Pa.
2. Connection of the pressure relief valve with the heater at the inlet of the water heater.
3. To avoid leakage when connecting the pipes, the rubber sealing gaskets supplied with the heater should be added at the end of the threads to ensure leak-proof joints (see Fig.4).
4. If you wish to make a multi-outlet supply system, refer to the method shown in Figures 5 and 6 to connect the piping.
5. The installation of electrolyte sleeves is mandatory. Recommended by the manufacturer to maintain the warranty.
6. The magnesium anode must be checked annually.

A	Hot water outlet
B	Rubber gaskets
C	Screw for hot water outlet
D	Mixing valve adjustment lever
E	Cold water inlet
F	Rubber gaskets
G	Pressure relief valve
H	Pressure relief orifice
I	Union screw for cold water inlet
J	Shower outlet
K	Power cable

A	Hot water outlet
B	Cold water inlet
C	Triple seal
D	Water tank
E	Mixing valve
F	Power cable
G	Main unit
H	Pressure relief valve
I	Water inlet valve
J	Shower outlet
K	Water inlet valve
L	Running water pipe

Be sure to use the accessories supplied by our company to install this electric water heater. This electric water heater cannot be hung on the bracket until it has been confirmed to be firm and reliable. Otherwise, the electric water heater may fall off the wall, which may cause damage to the heater, including serious injury accidents. When determining the location of the bolt holes, you should ensure that there is a clearance of not less than 0.2 m on the right side of the electric water heater to facilitate maintenance of the heater, if necessary.

Mode of use

First, open one of the water heater outlet valves and then open the water inlet valve. This will fill the water heater with water. When water comes out of the outlet pipe, the water heater is completely filled with water and the outlet valve can be closed.

Note:

During normal operation, the inlet valve should always be kept open.

This electric boiler is equipped with two regulators and two indicator lights on the control panel:

The left regulator regulates the heating power in four different levels:

Level 0: Standby mode (no heating).

Level 1: 800W power.

Level 2: 1200W power.

Level 3: Power of 2000W.

Depending on the needs, each user can choose the desired power.

The right knob is used to adjust the temperature, turn the knob clockwise to increase the water temperature. The adjustable temperature range is from 20°C to 75°C.

Power indicator (far left):

Illuminates when the unit is connected to a power source.

Heating (far right):

Illuminates when the thermos is heating.

WARNING! Before performing any maintenance, turn off the power.

WARNING! Non-professionals are not allowed to disassemble the thermostat to reset it. Please contact professionals to do the maintenance. Otherwise, our company will not be responsible if any accident occurs.

• Check the plug and socket as often as possible. There must be a safe electrical contact and proper grounding. The plug and socket must not become excessively hot.
• If the heater is not used for a long time, especially in regions with low ambient temperature (below 0°C), it is necessary to drain the water from the heater to avoid damage to the water heater due to freezing of the water in the inner tank. (Refer to the precautions in this manual for the method of draining the water from the inner tank).
• To ensure reliable and durable operation of the water heater, it is recommended to regularly clean the inner tank and remove deposits on the electric heating element of the water heater, as well as check the condition (completely decomposed or not) of the magnesium anode and, if necessary, replace it with a new one in case of complete decomposition. The frequency of cleaning the tank depends on the hardness of water located in this territory. Cleaning should be carried out by special maintenance services. You can ask the seller for the address of the nearest service center.

Safety valve

This electric boiler is fitted with a one-way safety valve. It should be installed in the water inlet port sector. When the pressure is higher than 0.8MPa , this valve will automatically release the pressure. There may be a water leakage in the pressure relief orifice sector, therefore, this orifice should never be blocked (Diagram 1).

To empty the tank, follow the instructions below.

If you need to empty the tank, first close the water inlet valve, then lift the plastic water inlet latch, then lift the water inlet latch again and allow the water in the tank to drain naturally (Diagram 2).

Whenever there is a problem with the appliance, check if you can solve it by following the tables below. If the problem persists, contact customer service.

DESCRIPTION POSSIBLE CAUSE SOLUTION
The heating indicator light is off.	Failure of the temperature controller.	Contact service for repair.
No water comes out of the hot water spout.	The mains water supply is cut off. The water pressure is too low. The tap water inlet valve is not open.	Wait for the running water supply to be restored. Resume using the heater when the water pressure increases. Open the tap water inlet valve.
No water comes out of the hot water outlet.	Temperature control system failure.	Contact service for repair.
Water leakage. Pipe gasket sealing problem. Seal the gaskets.

INFINITON

CALDEIRA ELÉCTRICA DE ÁGUA

Five white water heaters labeled 'INVESTON' arranged in a row, no text or symbols on the heaters themselves.

CAS3HV30L CAS3HV50L CAS3HV80L CAS3HV100L CAS3HV150L
ean: 8436546188834 ean: 8436546188841 ean: 8436546188858 ean: 8436546188865 ean: 8436546188872

Line drawing of a white Infiniton electric heater with control panel and gauge (no text or symbols on body)

¿Necesitas ayuda?

Silhouette icon of a person wearing a headset with a wrench inside (no text or symbols)

INFINITON

TÉRMINOS Y REGISTRO DE GARANTÍA