CDIN 1L380PB-80 - Dishwasher CANDY - Free user manual and instructions

Product type	Fully integrated dishwasher
Brand	CANDY
Model	CDIN 1L380PB-80
Category	Dishwasher
Nominal capacity	13 place settings
Width	60 cm
Depth	55 cm
Adjustable height	82-90 cm
Net weight	35 kg
Supply voltage	220-240 V ~ 50 Hz
Power input	1900 W
Water operating pressure	0.04-1.0 MPa
Annual energy consumption	255 kWh
Annual water consumption	2800 L
Energy efficiency class	E
Washing class	A
Drying class	A
Noise level	47 dB(A)
Wash programs	8 programs: Eco, Intensive, Normal, Quick, Glass, Delicate, Half Load, Soak
Options	Delayed start, Extra dry, Half load
Safety system	Anti-flood, Child lock, Panel lock
Tub material	Stainless steel
Included accessories	Cutlery basket, Spray arms, Filter
Installation type	Built-in / Integrated

Frequently Asked Questions - CDIN 1L380PB-80 CANDY

How to install the dishwasher?

To install the dishwasher, make sure the niche has a water supply and drain. Place the appliance, level it by adjusting the legs, connect the drain hose to the siphon and the water supply hose to the mains water system. Finally, fix the front panel for an aesthetic built-in finish.

How to fill the regenerating salt?

Open the cap of the salt container, located at the bottom of the dishwasher. Fill the tank with specific salt and add water (if necessary) up to the edge. Close the cap and start a wash cycle to remove any residues.

How to use the rinse aid?

The rinse aid should be poured into the designated dispenser, in the cover, up to the indicated level. Adjust the dosage via the selector based on the water hardness. The rinse aid helps drying and polishes the dishes.

How to clean the filters?

Rotate the cylindrical filter and pull it out. Remove the flat filter and wash all components under running water. Use a brush to remove residues. Reinstall the filters correctly to ensure optimal washing.

What to do if the dishwasher doesn't wash well?

Check that the filters are clean and that the spray arms are not clogged. Check the salt and rinse aid levels. Make sure the dishes do not block the arms. Finally, select a more intensive program if the load is very dirty.

How to start the automatic program?

After loading the dishes, add the detergent, select the desired program via the selector and press the Start button. The display shows the remaining time. For greater convenience, you can set the delayed start up to 24 hours.

What do the error codes mean?

The error codes on the display indicate anomalies such as water malfunction (E1), drain problems (E2) or thermal faults (E3). Turn off the appliance, check water intakes and pipes, and if the problem persists contact the technical support.

How to replace the drain hose?

Disconnect the dishwasher from the power supply. Remove the drain hose from the siphon, loosen the clamp at the base of the appliance and replace it with a new hose of the same diameter. Secure it tightly and check for leaks.

How to remove limescale?

Use a specific descaling agent for dishwashers. Run an empty cycle with the descaling agent at 60°C. Repeat the treatment if necessary. To prevent limescale, always maintain the salt level and use the rinse aid.

How to reset the dishwasher?

To reset the dishwasher, hold down the Start button for 3 seconds until the display turns off. Wait 10 minutes and turn it back on. If the appliance still does not work, disconnect the power for 5 minutes and try again.

USER MANUAL CDIN 1L380PB-80 CANDY

Regeneration
			EN Standard Conditions
Setting	0	1	2	3	4	5
Frequency	Never	1 every 9 cycles	1 every 5 cycles	1 every 4 cycles	1 every 2 cycles	Every cycle

EN The information on specific models is available in the product database at the following link: https://eprel.ec.europa.eu/. Simply search for the model identification number, which can be found on the product label under the "Mod." field.