640-270 - Vacuum Cleaner Melissa - Free user manual and instructions

Product Type	Cylinder Vacuum Cleaner
Brand	Melissa
Model	640-270
Power Supply	230V, 50Hz
Power Consumption	1600W (estimated)
Dust Bag Capacity	2.5 L (estimated)
Filtration	Motor filter and exhaust filter (HEPA)
Cord Length	5 m (estimated, with automatic rewind)
Suction Control	Air valve on handle for variable suction
Floor Nozzle	Two settings via brush function button (hard floor/carpet)
Accessories	Crevice nozzle, brush nozzle
Bag Change Indicator	Yes
Automatic Cord Rewind	Yes
Storage Bracket	For floor nozzle storage on appliance
Carrying Handle	Yes
Weight	4.5 kg (estimated)
Dimensions (approx.)	40 x 30 x 25 cm (estimated)
Noise Level	Not specified

Frequently Asked Questions - 640-270 Melissa

How do I replace the dust bag?

Turn off and unplug the appliance. Open the lid by pressing the button underneath the edge. Remove the old dust bag carefully, avoiding bending or squeezing. Place a new dust bag, ensuring it is secure and facing the right direction. Close the lid until it clicks.

How do I clean the motor filter?

Unplug the appliance. Open the lid and remove the dust bag. Take out the motor filter from its holder. Shake or beat it gently to remove dust, or wash it in warm water if dirty. Ensure it is completely dry before replacing. Reinsert the filter and dust bag, then close the lid.

How do I clean the exhaust filter?

Remove the exhaust grille by pressing the release button. Take out the exhaust filter. Clean by shaking off dust or washing gently in warm water. Let it dry fully. Reattach the filter to the grille and snap the grille back into place.

What should I do if the bag change indicator stays on after replacing the bag?

If the indicator remains red, it may be due to a clogged hose or nozzle, or a dirty exhaust filter. Check the hose and nozzle for blockages. Clean or replace the exhaust filter. Do not use the appliance if the indicator is on, as it may damage the motor.

Can I vacuum wet surfaces or liquids?

No, this vacuum cleaner is for dry use only. Never vacuum wet surfaces, matches, hot ashes, cigarette butts, hard/sharp objects, or combustible materials. Doing so may cause injury or damage.

How do I adjust the suction strength?

Use the air valve on the hose handle. Close the valve for full suction (normal setting). Open the valve to reduce suction power, ideal for curtains or lightweight items.

How do I use the floor nozzle for different surfaces?

Press the brush function button on top of the nozzle. For hard surfaces (stone, tiles), extend the brushes. For carpets and rugs, retract the brushes into the nozzle.

How do I store the vacuum cleaner?

Rewind the cord by pressing the automatic rewind button while holding the plug. Store the floor nozzle in the storage bracket at the rear of the appliance. Keep the appliance in a clean, dry place, and do not place heavy objects on top.

What precautions should I take while using?

Do not use on wet surfaces. Keep hair, clothing, and body parts away from moving parts. Avoid vacuuming fine sand or dust. Never cover suction or exhaust ports. Unplug when not in use and before cleaning or replacing parts.

How do I rewind the power cord?

Switch off and unplug from the mains. Press the automatic cord rewind button on the left side of the carrying handle. Hold the plug while rewinding to prevent it from hitting the appliance.

USER MANUAL 640-270 Melissa

Black vacuum cleaner with coiled handle and ventilation slots (no text or symbols visible)

640-256/ 140-021/ 140-020/ 640-258/ 640-273/ 640-268/ 640-269/ 640-270/ 640-274

DK Støvsuger....2

SE Dammsugare....6

NO Støvsuger....10

FI Pölynimuri....14

UK Vacuum cleaner....18

DE Dammsugare....22

PL Odkurzacz....26

DK

INTRODUKTION

OVERSIGT OVER APPARATETS DELE

KLARG∅RING AF APPARATET

UDSKIFTNING AF ST∅VPOSE

KLARGJ∅RING AV APPARATET

Frequently asked questions.

To get the best out of your new appliance, please read this user guide carefully before using the appliance for the first time. Take particular note of the safety precautions. We also recommend that you keep the instructions for future reference, so that you can remind yourself of the functions of your appliance.

SAFETY MEASURES

General

Incorrect use of this appliance may cause personal injury and damage.

Use for its intended purpose only. The • manufacturer is not responsible for any injury or damage resulting from incorrect use or handling (see also Guarantee Terms).

For domestic use only. Not for outdoor or commercial use.

For connection to 230 V, 50 Hz only.

Do not immerse the appliance, cord or • plug in water or any other liquid and make sure no water enters the appliance.

Never touch the appliance, cord or plug • with wet or damp hands.

Do not expose to direct sunlight, high • temperatures, humidity or corrosive substances.

Never leave the appliance unattended • when it is switched on.

Keep the appliance under constant • supervision while in use. Keep an eye on children in the vicinity of the appliance when it is being used. The appliance is not a toy.

The appliance is not to be used by persons with reduced sensitivity, physical or mental disabilities or persons who are unable to use the appliance, unless supervised or instructed by a person responsible for their safety.

Do not use if the exhaust filter (HEPA filter) • motor filter and dust bag are not fitted, as this could damage the appliance.

- Only use accessories manufactured or recommended by the manufacturer.

Use

• Do not use the appliance on wet surfaces. Take particular care when vacuuming • stairs, due to the risk of falling. Do not use the kit to vacuum up matches, • hot ashes, cigarette butts, hard or sharp objects, wet or damp substances, combustible materials (petrol, solvents, etc.) or vapour from these.
• Do not use to vacuum fine sand or dust – e.g. plaster, brick dust and the like.
• Ensure that you keep clothing, hair and body parts away from the nozzle and moving parts of the appliance.
• Never insert anything into the openings of the appliance.
• Do not cover the appliance's suction or exhaust port.

Cord and plug

• Keep the cord and appliance away from heat sources, hot objects and naked flames.
  Take care to prevent bending and kinking • of the cord and avoid pulling the cord around sharp corners or jamming it in doors, etc.
• Switch off the appliance and unplug it when it is not in use, and before you replace the dust bag and clean or replace the filters.
  o Avoid pulling the cord when removing the plug from the socket. Instead, hold the plug.
  Keep hold of the plug when rewinding the cord, so that it does not bump against the appliance or any other objects in the vicinity.
• Check regularly that neither cord nor plug is damaged. Do not use if they are damaged or if the appliance has been dropped or damaged in any other way. If the appliance, cord or plug have been damaged, have the appliance inspected and if necessary repaired by an authorised repairer. Never try to repair the appliance yourself. Please contact the store where you bought the appliance for repairs under the guarantee. Unauthorised repairs or modifications to the appliance will invalidate the guarantee.

KEY TO THE MAIN COMPONENTS OF THE APPLIANCE

Carrying handle and button for automatic 1.

cord rewind

ON/OFF button2.

Bag change indicator3.

Lid4.

Hose connector port5.

Air valve6.

Handle7.

Hose8.

Hose connector9.

Two-component tube10.

Brush function button11.

Floor nozzle12.

Crevice/brush nozzle13.

1. Motor filter
2. Exhaust filter
3. Exhaust grille
4. Exhaust (behind the grille)
5. Storage bracket

PREPARING THE APPLIANCE

IMPORTANT! Before using the appliance, open the lid (4) and make sure the motor filter (14) and the dust bag have been fitted to the appliance. Also check that the exhaust filter (15) is in place in the exhaust port (17). See Replacing filter and dust bag below.

1. Attach the hose (8) to the appliance by inserting the hose connector (9) in the hole on the hose connector port (5) on the top of the appliance, until you hear a click.
   To remove the hose, press the buttons on the side of the hose connector and pull the hose out.
2. Assemble the two-component tube (10), joining the two parts
3. Attach the handle of the hose (7) to one end of the tube and attach the floor nozzle (12) to the opposite end of the tube

USING THE APPLIANCE

1. Pull the cord out of the appliance. The cord may not be pulled out further than the yellow mark. Plug in and switch on the power.
2. Press the On/Off button (2) to switch the appliance on and off.
3. Suction strength can also be adjusted by opening and closing the air vent (6) on the handle.

o When the valve is closed, full suction is achieved. This is the normal setting.
When the vent opens, more air is allowed in, reducing the suction power at the floor nozzle. This function is ideal for cleaning curtains and other light items which can easily get sucked into the nozzle at maximum suction strength.

1. The floor nozzle brushes have two settings which can be selected using the brush function button (11) on top of the nozzle.

When cleaning hard surfaces (stone flooring, tiles, etc.), the nozzle brushes should be extended.
When cleaning carpets and rugs, the brushes should be retracted into the nozzle.

1. If the bag change indicator (3) indicates that the bag is full or if suction force is significantly reduced, the bag must be replaced (see section Replacing Dust Bag, below). If the indicator continues to indicate that the bag is full after you have replaced it, this may be due to one of the following:

o The hose or nozzle is clogged.
o The exhaust filter is dirty.

Investigate and resolve the problem. Do not use the appliance if the indicator indicates that the dust bag is full. This may cause irreparable damage to the motor.

1. NOTE! Switch off the appliance on the On/Off button, disconnect the plug from the mains socket and allow the appliance to cool off for approx. 1 hour. Clean the filters and replace the dust bag (see the sections on replacement of filters and dust bag below), before using the appliance again.

Tips

If you need to take a break during vacuum • cleaning, you can slide the floor nozzle into the storage bracket (18) on the back of the appliance.

The small crevice and brush nozzle (13) • can be used with and without brushes, as they can easily be extended or withdrawn. The nozzle can be stored in the storage space on the back of the appliance when it is not in use.

You can lift and carry the appliance using • the carrying handle (1). Never pull or lift the appliance by the cord.

REPLACING THE DUST BAG

If the bag change indicator indicates that the bag is full or if the suction force is significantly reduced, this may mean that the dust bag needs replacing. Never use the appliance if the bag is full or with no bag at all.

Turn off the appliance.1.

Detach the hose.2.

Open the lid by pressing the button 3. underneath the edge of the lid and lifting the lid until it locks into place.

Remove the dust bag.4.

Place the bag carefully in a refuse bin. 5.

Make sure that there are no holes in it.

Avoid bending or squeezing the bag.

Place a new dust bag in the appliance. 6. Check that the bag is secure and facing in the right direction.

Close the lid and ensure it clicks into place.7.

REPLACING THE MOTOR FILTER

The motor filter is the filter behind the dust bag. The appliance must not be used without a motor filter.

Turn off the appliance.1.

Detach the hose.2.

Open the lid by pressing the button 3. underneath the edge of the lid and lifting the lid until it locks into place.

Remove the dust bag from the appliance.4. Remove the motor filter from the holder and 5. replace the filter or clean it as described in the section on cleaning below.

1. Replace the motor filter in the holder.

2. Check the dust bag is correctly fitted onto the rails before closing the lid.

We recommend cleaning the filter at least twice a year, or whenever it is dirty.

REPLACING THE EXHAUST FILTER

The exhaust filter is used to filter exhaust air from the appliance. The appliance must not be used without an exhaust filter.

• Remove the exhaust grille (16) on the side of the appliance by pressing the release button on the grille.
• Remove the exhaust filter from the back of the grille and replace the filter or clean it as described in the section on cleaning below.
• Replace the exhaust filter on the back of the grille.
• Fit the exhaust grille and ensure it clicks into place.

We recommend replacing the exhaust filter after 4 to 6 months' use, when it becomes soiled, or if the vacuum cleaner's suction force is reduced.

STORAGE

Before putting the appliance away, rewind the cord. Switch off at the mains, remove the plug and press the automatic cord rewind button on the left side of the carrying handle until the cord is completely rewound. Hold the plug during rewinding to prevent it from hitting the appliance as this could damage either the appliance or the plug.

• The floor nozzle can be stored in the storage bracket at the rear end of the appliance.
• Store the appliance in a clean and dry place.
• Do not place heavy objects on top of the appliance.

CLEANING

When cleaning the appliance, you should pay attention to the following:

• Unplug the appliance before cleaning it. Never submerge the appliance in water and make sure no water enters the appliance.
• Clean the appliance by wiping it with a damp cloth. A little detergent can be added if the appliance is heavily soiled.
• Do not use scouring pads, steel wool or any form of strong solvents or abrasive cleaning agents to clean the appliance, as they may damage the external surfaces of the appliance.
  IMPORTANT! Allow to dry completely after • cleaning. Do not use the appliance if it is damp.

Take care to keep the filters clean.

Remove the filters as described above. o Shake and beat the filters carefully to o remove dust and dirt.

The filter pad can be gently washed in o warm water.

Check they are completely dry before o replacing in the appliance. NEVER insert a wet filter into the appliance.

Replace filters with the same type when o worn or cannot be cleaned properly.

FOR UNITED KINGDOM ONLY

Plug wiring:

This product is fitted with a BS 1363 13-amp plug. If you have to replace the fuse, only those that are ASTA or BSI approved to BS1362 and with a rated current of 13 amps should be used. If there is a fuse cover fitted, this cover must be refitted after changing the fuse. If the fuse cover is lost or damaged, the plug must not be used. You must also check if the socket outlets in your home fit with the plug of the appliance. If the socket outlet in your home does not fit with the plug, the plug must be removed and disposed of safely as insertion of the plug into the socket is likely to cause electric hazard.

As this product is a class II appliance, the pin of BS plug for earth connection is false.

INFORMATION ON DISPOSAL AND RECYCLING OF THIS PRODUCT

Please note that this Adexi product is marked

with this symbol:

This means that this product must not be disposed of along with ordinary household waste, as electrical and electronic waste must be disposed of separately.

In accordance with the WEEE directive, every member state must ensure correct collection, recovery, handling and recycling of electrical and electronic waste. Private households in the EU can take used equipment to special recycling stations free of charge. In certain member states, used appliances can be returned to the retailer where they were bought on the condition you buy new products. Contact your retailer, distributor or the municipal authorities for further information on what to do with electrical and electronic waste.

GUARANTEE TERMS

The guarantee does not apply:

if the above instructions have not been • followed

if the appliance has been tampered with•

if the appliance has been mishandled, •

subjected to rough treatment, or has suffered any other form of damage

if the appliance is faulty due to faults in the • electricity supply.

Due to the constant development of our products in terms of function and design, we reserve the right to make changes to the product without prior warning.

FREQUENTLY ASKED QUESTIONS

If you have any questions regarding the use of the appliance and cannot find the answer in this user guide, please try our website at www.adexi.eu.

Go to the "Consumer Services" menu and click on "Frequently Asked Questions" to view the most frequently asked questions.

You can also see contact details on our website if you need to contact us for technical questions, repairs, accessories or spare parts.

IMPORTER

Adexi Group

www.adexi.eu

We cannot be held responsible for any printing errors.

DE

EINLEITUNG