CPS1000E - Inverter CyberPower - Free user manual and instructions
Find the device manual for free CPS1000E CyberPower in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Uninterruptible Power Supply (UPS) |
| Model | CPS1000E |
| Brand | CyberPower |
| Topology | Line-Interactive |
| VA Rating | 1000 VA |
| Watt Rating | 600 W |
| Input Voltage | 230 VAC |
| Input Frequency | 50/60 Hz (auto-sensing) |
| Output Voltage (on battery) | 230 VAC ± 10% |
| Number of Outlets | 6 (battery + surge) + 2 (surge only) |
| Battery Type | Sealed lead-acid, maintenance-free |
| Typical Backup Time (half load) | 12 minutes |
| Typical Backup Time (full load) | 4 minutes |
| Battery Recharge Time | 8 hours to 90% capacity |
| Automatic Voltage Regulation (AVR) | Yes (boost and buck) |
| USB Port | 1 (HID-compliant for monitoring) |
| Surge Protection | Yes (RJ11/RJ45, coaxial, phone line) |
| Dimensions (W x H x D) | 8.7 x 11.8 x 14.2 inches (221 x 300 x 361 mm) |
| Weight | 24.3 lbs (11 kg) |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Safety Certifications | UL, cUL, FCC Class B |
| Warranty | 3 years (2 years on battery) |
Frequently Asked Questions - CPS1000E CyberPower
How do I replace the battery in my CyberPower CPS1000E?
The battery is user-replaceable. Turn off the UPS, unplug it, then open the front panel. Disconnect the battery terminals, remove the old battery, and install a new CPS1000E replacement battery (model: RB1290A). Reconnect terminals and close the panel.
Why does my UPS beep continuously?
Continuous beeping indicates the battery is low or the UPS is overloaded. Check the load: ensure connected equipment does not exceed 600W. If the beeping persists, the battery may need replacement.
What is the typical runtime for the CPS1000E?
At half load (300W), runtime is approximately 12 minutes. At full load (600W), runtime is about 4 minutes. Actual runtime varies with equipment and battery age.
Can I connect a laser printer to this UPS?
Laser printers draw high peak power and are not recommended. Connect only sensitive electronics like computers, monitors, and routers. Printers should be plugged into surge-only outlets.
How do I perform a self-test on the CPS1000E?
Press and hold the Power button for about 2 seconds to initiate a self-test. The UPS will switch to battery mode briefly, then return to AC. The display will show test results.
What do the LED indicators mean?
Green LED: normal AC mode. Yellow LED: on battery or AVR active. Red LED: battery low or fault. Refer to the user manual for a full matrix of LED patterns.
Does the CPS1000E have surge protection for phone lines?
Yes, it includes RJ11/RJ45 surge protection for phone/network lines. Connect your modem or router to these jacks for additional protection.
How do I clean and maintain the UPS?
Unplug the UPS and use a dry, soft cloth to wipe the exterior. Do not use liquids or aerosols. Ensure vents are free of dust. Perform a battery self-test every 3 months.
My UPS does not turn on. What should I check?
First, ensure it is plugged into a working wall outlet. Check the input circuit breaker on the back; if tripped, push it in. If still off, the battery may be completely discharged or defective.
What is the warranty on the CyberPower CPS1000E?
The UPS carries a 3-year warranty and the battery has a 2-year warranty. CyberPower also offers connected equipment coverage up to $100,000 with proper registration.
User questions about CPS1000E CyberPower
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Inverter in PDF format for free! Find your manual CPS1000E - CyberPower and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CPS1000E by CyberPower.