Ecostar WF40 - Water heater Braemar - Free user manual and instructions

Type de produit	Chauffe-eau électrique à accumulation
Marque	Braemar
Modèle	Ecostar WF40
Capacité	40 gallons (151 litres)
Alimentation électrique	240 V ~ 50 Hz
Puissance nominale	3.6 kW
Pression de service maximale	700 kPa
Température maximale de l'eau	75 °C
Dimensions (hauteur × diamètre)	600 mm × 450 mm
Poids à vide	20 kg
Matériau de la cuve	Acier émaillé
Isolation	Polyuréthane haute densité
Réglage du thermostat	Variable de 30 °C à 75 °C
Protection contre la surchauffe	Dispositif de sécurité à réenclenchement manuel
Soupape de sécurité	Intégrée, tarée à 700 kPa
Anode de protection	Anode en magnésium, remplaçable
Entretien recommandé	Vidange annuelle et contrôle de l'anode
Nettoyage	Essuyer l'extérieur avec un chiffon humide; ne pas utiliser de produits abrasifs
Pièces de rechange disponibles	Élément chauffant, thermostat, anode, soupape de sécurité
Garantie	5 ans sur la cuve, 1 an sur les pièces
Normes	Conforme aux normes AS/NZS 3350.2.21

Frequently Asked Questions - Ecostar WF40 Braemar

Comment régler la température de l'eau sur le Braemar Ecostar WF40 ?

Le thermostat se trouve généralement sous le capot avant. Utilisez un tournevis pour ajuster la molette de réglage entre 30°C et 75°C. Pour économiser l'énergie, réglez à 60°C. Consultez la notice pour plus de détails.

Que faire si l'eau ne chauffe pas ?

Vérifiez d'abord l'alimentation électrique (disjoncteur). Ensuite, testez le thermostat et l'élément chauffant. Si l'élément est défectueux, remplacez-le. Il est recommandé de faire appel à un professionnel.

À quelle fréquence dois-je vidanger le chauffe-eau ?

Il est recommandé de vidanger le chauffe-eau une fois par an pour éliminer les dépôts de calcaire. Cela prolonge la durée de vie de l'appareil et maintient son efficacité.

Comment changer l'anode de protection ?

L'anode en magnésium doit être vérifiée annuellement. Pour la remplacer, vidangez partiellement le chauffe-eau, dévissez l'ancienne anode et installez la nouvelle. Utilisez du ruban téflon pour l'étanchéité.

Quelle est la pression d'eau maximale autorisée ?

La pression de service maximale est de 700 kPa. Si la pression d'alimentation dépasse cette valeur, installez un réducteur de pression.

Le chauffe-eau fuit par la soupape de sécurité, est-ce normal ?

Un léger suintement lors du chauffage est normal. Si la fuite est continue ou importante, la soupape est peut-être défectueuse ou la pression est trop élevée. Remplacez la soupape si nécessaire.

Puis utiliser des produits détartrants chimiques ?

Non, n'utilisez pas de produits chimiques agressifs. Pour le détartrage, privilégiez un nettoyage mécanique ou un détartrant spécifique pour chauffe-eau. Consultez un professionnel.

Comment économiser de l'énergie avec le Braemar Ecostar WF40 ?

Réglez le thermostat à 60°C, isolez les tuyaux d'eau chaude et utilisez un minuteur pour chauffer l'eau aux heures creuses. Une isolation supplémentaire du chauffe-eau peut aussi réduire les pertes.

Où puis-je trouver les pièces de rechange ?

Les pièces de rechange sont disponibles chez les revendeurs agréés Braemar ou en ligne. Les pièces courantes comme l'élément chauffant, le thermostat et l'anode sont facilement trouvables.

Le voyant lumineux reste allumé en permanence, que faire ?

Cela peut indiquer un thermostat défectueux ou un élément chauffant qui fonctionne en continu. Vérifiez la température de l'eau : si elle est trop chaude, coupez l'alimentation et remplacez le thermostat.

USER MANUAL Ecostar WF40 Braemar

It is a condition of your warranty cover that the items in the Schedule below are checked (and action taken as required) every two (2) years after the date of installation by a qualified, licenced technician, and that the Schedule is properly filled out (ie names, signature, date, and action taken). Even after the warranty period expires, please continue to have the product maintained every two years as per the items in the Schedule. This will help to prolong the life of the product and keep it running efficiently. Maintenance Schedule

Year	248610
Name of Technician and company (Print)
Signature of Technician
Date of attendance

Cabinet and components

Cabinet
Heat exchanger
Electrical connections
Combustion air inlet louvres

General installation

Rear register
Flue system, cowl
Electrical and gas connections

Electrical

Electrical wiring
Room fan motor / impellor
Thermocouple voltage
Overtemp switch

Gas, burners, ignition

Main burner and injector
Pilot gas rate
Pilot burner and injector
Pilot ignition / ignition electrode

Operation

Start up and run sequence
Control operation
Complete ignition
Gas inlet pressure	kPa	kPa	kPa	kPa	kPa
Gas test point pressure High	kPa	kPa	kPa	kPa	kPa
Gas test point pressure Low	kPa	kPa	kPa	kPa	kPa
Thermostat operation
Draught diverter (NOTE 1)

Action taken key:

√ = Inspected and working correctly no action required
A = Adjustment of part
C = Cleaning of part
R = Replaced part

NOTE 1

Check operation of flue and draft diverter in accordance with detailed instructions included in AS/NZS 56001.

To owner/user, please note that as explained in your Warranty Card installation is not covered by the warranty (for example, electrical and gas

Warranty Service Australia 1-300-650-644 seeleyinternational.com

SEELEY INTERNATIONAL

OWNER'S MANUAL

Wall Furnace - WF30/40

Exterior view of a tall, beige cylindrical device with gray bands (no visible text or symbols)

IMPORTANT MAINTENANCE (AND WARRANTY) INFORMATION

As with any product that has moving parts or is subject to wear and tear, it is VERY IMPORTANT that you maintain your wall furnace and have it regularly serviced. It is a condition of warranty cover for your wall furnace that you comply with all of the maintenance and service requirements set out in this Owner's Manual. Compliance with these requirements will prolong the life of your wall furnace. Further, it is also a condition of warranty cover that each item in the Maintenance Schedule in this Owner's Manual is performed with the frequency indicated, by a qualified, licensed technician, and that the Maintenance Schedule is properly filled out (ie names, signature, date, and action taken) when the item is completed. ANY FAILURE TO CARRY OUT THE REQUIRED MAINTENANCE AND SERVICING REQUIREMENTS, AND ANY FAILURE TO PROPERLY FILL OUT THE MAINTENANCE SCHEDULE, WILL VOID YOUR WARRANTY.

Care Instructions

External surfaces should be cleaned with warm water and detergent with the heater turned off. Do not use abrasive cleaners as scratching of the surface will occur.

Warning

DO NOT: Place articles on or against this appliance.

DO NOT: Use or store flammable materials near this appliance

DO NOT: Spray aerosols in the vicinity of this appliance while it is in operation.

DO NOT: Modify this appliance.

IMPORTANT

If for any reason your heater experiences, a POWER FAILURE, the "Pilot Flame" is TURNED OFF, or GOES OUT, a period of up to 5 minutes is required for the heater to reset.

If the heater has not reset, the "Gas control knob" will NOT turn easily.

PLEASE DO NOT FORCE

Damage to the mechanism may occur.

OPERATING INSTRUCTIONS

Introduction

For satisfactory performance of your Braemar gas wall furnace, please read these instructions carefully. The operation of the heater is controlled by the gas control knob and fan switch located behind the access door on the front cover.

Fan Operation

The fan will start automatically in both AUTO and BOOST positions when the unit is warm enough after the burner is turned on, and stop automatically when the unit has cooled sufficiently after the burner turns off. With AUTO selected the unit will automatically select between "low" and "normal" (and "boost" on 40MJ models) fan speeds based on the heated air temperature - no further user adjustment is necessary. When BOOST is selected the fan will run only on its boost speed. It is recommended that the manual fan switch be set to AUTO for normal operation, or BOOST for rapid heat-up.

Gas Control

To light the heater:

• Turn the gas control knob anti-clockwise from the "0" position to the ★ position.
• Depress knob fully and hold down.
• Press the igniter button located next to the gas control knob 3-4 times.
• Observe the pilot meter to indicate operation of the pilot.
• Wait 20 seconds then release the gas control knob and check the pilot meter stays on.

Heat Setting

• Turn gas control knob anti-clockwise to desired heat setting between "1" and "7".
• The heater will automatically adjust the gas flow to maintain the room temperature corresponding to the selected heat setting.

To Increase Heat Setting

- Turn gas control knob anti-clockwise towards "7".

To Decrease Heat Setting

- Turn gas control knob clockwise towards "1".

To Turn Off Main Burner (Pilot-Stand by)

- Turn gas control knob clockwise to a position between the word PILOT & the symbol ★.

(see "Pilot zone" Figure 1 below) It is recommended that the pilot be left in operation during the heating season.

To Turn Off Completely (end of heating season)

- Turn gas control knob clockwise to the "0" position.