AF-7 - Fan Eurolite - Free user manual and instructions

Product Type	Axial Blower with DMX Control
Model	AF-7
Dimensions (L x W x H)	480 x 420 x 500 mm
Weight	7.3 kg
Power Supply	230 V AC, 50 Hz
Power Consumption	170 W
Fan Diameter	310 mm
Maximum Speed	2600 RPM
Maximum Airflow	55 m³/min
DMX Channels	1
DMX Connection	3-pin XLR (input and output)
Control Methods	Rotary dial (standalone) or DMX controller
Display	4-digit LED with menu buttons (Menu, Up, Down, Enter)
Housing Material	Sturdy metal
Mounting	Standing installation only (included stand with tilt adjustment)
Protection Class	I (earth connection required)
Safety Features	Thermal protection? (not specified, but fuse protection)
Fuse	Replaceable fuse of same type and rating
Operating Temperature	-5°C to +45°C
Relative Humidity	Max 50% at 45°C
Cleaning	Disconnect from mains; use soft, lint-free, damp cloth; no alcohol or solvents
Accessories Included	Power cord with safety plug, stand, fixation screws, washers
Intended Use	Professional stage and event technology, indoor use only

Frequently Asked Questions - AF-7 Eurolite

How do I adjust the wind speed on the Eurolite AF-7?

In stand-alone mode, use the rotary control on the front panel to adjust wind speed from OFF (MIN) to maximum (MAX). The display shows 000 (off) to 099 (maximum 100%). After use, turn the control to MIN to switch off.

How do I set the DMX address on the AF-7?

Press the MENU button until 'Addr' appears on the display. Press ENTER, then use UP or DOWN to set the starting address (d001 to d512). Press ENTER to confirm. The device uses one DMX channel.

What is the maximum airflow of the Eurolite AF-7?

The maximum airflow is 55 m³/min at 2600 RPM.

Can I use this fan outdoors?

No, the Eurolite AF-7 is designed for indoor use only. Keep it away from rain, moisture, and extreme temperatures. The operating temperature range is -5°C to +45°C.

How do I clean the AF-7 axial fan?

Always disconnect from mains before cleaning. Use a soft, lint-free, damp cloth. Never use alcohol, solvents, or abrasive cleaners. Avoid letting liquids enter the housing.

How do I replace the fuse on the AF-7?

Unplug the device. Unscrew the fuse holder on the rear panel (anti-clockwise) using a fitting screwdriver. Remove the old fuse and insert a new fuse of the same type and rating. Screw the holder back in place.

What DMX cable do I need for the AF-7?

Use a standard DMX cable with 3-pin XLR connectors. The device has both DMX input and output (male and female). For long runs, ensure proper termination with a 120 Ω resistor at the last fixture.

Why is my AF-7 not responding to DMX?

Check that the DMX cable is securely connected to the input. Ensure the controller is on and sending data. Verify the DMX address is set correctly and does not conflict with other devices. The display should flash when receiving DMX data.

Can I mount the AF-7 on a wall or ceiling?

No, this device is designed for standing installation only using the included stand. It must be placed on a flat, vibration-free, and fire-resistant surface. Do not hang or mount it.

What is the power consumption of the Eurolite AF-7?

The power consumption is 170 W at 230 V AC, 50 Hz. The device comes with a power cord with a safety plug. Ensure the mains outlet is properly earthed.

USER MANUAL AF-7 Eurolite

Technical line drawing of a fan-shaped industrial fan with internal blades and mounting bracket (no text or symbols)

Axial blower with DMX control

No. 80208057

www.eurolite.de

Inhaltsverzeichnis

Table of contents

Deutsch

EINFÜHRUNG 3

Connection with the mains 16

DMX512 control 16

OPERATION 17

Menu structure 17

Adjusting wind speed via rotary control 18

DMX-controlled operation 18

Addressing 18

DMX protocol 18

CLEANING AND MAINTENANCE 19

Replacing the fuse 19

TECHNICAL SPECIFICATIONS.... 19

This user manual is valid for the article number 80208057

You can find the latest update of this user manual in the Internet under:

www.eurolite.de

BEDIENUNGSANLEITUNG

eurolite®

Keep this device away from rain and moisture!

Never open the housing!

For your own safety, please read this user manual carefully before you initially start-up.

Every person involved with the installation, operation and maintenance of this device has to

• be qualified
• follow the instructions of this manual
• consider this manual to be part of the total product
• keep this manual for the entire service life of the product
• pass this manual on to every further owner or user of the product
• download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen an EUROLITE AF-7 Axial Blower DMX. If you follow the instructions given in this manual, we are sure that you will enjoy this device for a long period of time.

Unpack your AF-7 Axial Blower DMX.

SAFETY INSTRUCTIONS

CAUTION!

Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires!

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

English

Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C connection cable or on the casing, do not take the device into operation and immediately consult your local dealer.

This device falls under protection-class I. The power plug must only be plugged into a protection class I outlet. The voltage must exactly be the same as stated on the device. Wrong voltages or power outlets can lead to the destruction of the device and to mortal electrical shock.

Always plug in the power plug least. The power plug must always be inserted without force. Make sure that the plug is tightly connected with the outlet.

Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal electrical shock.

Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.

The cable insert or the female part in the device must never be strained. There must always be sufficient cable to the device. Otherwise, the cable may be damaged which may lead to mortal damage.

Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time.

If extension cords are used, make sure that the core diameter is sufficient for the required power consumption of the device. All warnings concerning the power cords are also valid for possible extension cords.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the device must be disconnected via the mains.

If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More severe dirt in and at the device should only be removed by a specialist.

There must never enter any liquid into power outlets, extension cords or any holes in the housing of the device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced insulation can cause mortal electrical shock.

There must never be any objects entering into the device. Even smallest parts or liquids can harm the machine's perfect operation. This is especially valid for metal parts. If any metal parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries.

Sand or small stones can turn into dangerous bullets if accelerated by the axial fan. Always wear ear protection!

When installing the device make sure that permanent and perfect airflow is guaranteed.

Never place the axial fan directly to an object or wall.

Keep away children and amateurs!

Never leave this device running unattended.

OPERATING DETERMINATIONS

This device is an axial blower for creating wind. This product is only allowed to be operated with an alternating voltage of 230 V, 50 Hz and was designed for indoor use only.

This device is designed for professional use in the field of event technology, e.g. on stage.

Do not shake the device. Avoid brute force when installing or operating the device.

Make sure that the installation complies with the standards and rules that apply in your country. The device must be installed securely and prevented from falling down.

When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture or dust. There should not be any cables lying around. You endanger your own and the safety of others!

The device must only be installed absolutely planar at a vibration-free, oscillation-free and fire-resistant location.

This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or fog may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0.5 meters between smoke machine and device. The room must only be saturated with an amount of smoke that the visibility will always be more than 10 meters.

This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the housing, immediately unplug the unit and contact a service technician before using it again.

The operational surroundings must be free from solid or liquid easy-to-move objects, which could be tilted, absorbed or accelerated by the air flow.

Locate the axial blower in a well-ventilated area. Never cover the unit's vents. The axial blower is best installed 1 meter away from all objects.

The ambient temperature must always be between -5^ C and +45^ C. Keep away from direct insulation (particularly in cars) and heaters.

The relative humidity must not exceed 50 % with an ambient temperature of 45^ C.

This device must only be operated in an altitude between -20 and 2000 m over NN.

Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the device during thunderstorms.

Operate the device only after having familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation!

Please use the original packaging if the device is to be transported.

Please consider that unauthorized modifications on the device are forbidden due to safety reasons!

If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, etc.

WEEE Directive

When to be definitively put out of operation, take the unit(s) to a local recycling plant for a disposal which is not harmful to the environment. Do not dispose of as municipal waste. Contact your retailer or local authorities for more information.

DESCRIPTION OF THE DEVICE

Features

Compact axial blower with DMX control

• Wind machine with DMX control for stage and touring applications
• Sturdy metal housing
- Easy operation
- Great effect when used e.g. with fog, snow and bubble machines
• Control via rotary dial or DMX
- Addressing via control board with 4-digit LED display
- Locking possibility at the brackets
- Ready for connection via power cord with safety-plug
- DMX control via any standard DMX controller

Overview

(1) Stand
(2) Fixation screw
(3) Housing
(4) Ventilator/ventilation grille
(5) Handle
(6) 3-pin DMX input
(7) 3-pin DMX output
(8) Control board
(9) Display
(10) Enter button
(11) Down button
(12) Up button
(13) Menu button
(14) Rotary control wind speed
(15) Power input
(16) Fuse holder

INSTALLATION

Mounting

1. Use the handle to place the ventilator on the stand as shown in the image.
2. Fix the fan to the stand using the two fixation screws and washers.
3. You can now freely adjust the fan's tilt.
4. Further tighten the fixation screws.

The device is designed for standing installation only.

Install the device out of the public area.

Only install the machine on scratch resistant surfaces. The device must only be installed absolutely planar at a vibration-free, oscillation-free and fire-resistant location.

The operational surroundings must be free from solid or liquid easily moveable objects, which could be knocked over, absorbed or accelerated by the air flow.

English

Connection with the mains

Connect the device to the mains with the power-plug.

The occupation of the connection-cables is as follows:

Cable	Pin	International
Brown Live L
Blue Neutral N
Yellow/Green Earth		[523H]

The earth has to be connected!

If the device will be directly connected with the local power supply network, a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.

The device must only be connected with an electric installation carried out in compliance with the IEC-standards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum fault current of 30 mA.

DMX512 control

The wires must not come into contact with each other, otherwise the devices will not work at all, or will not work properly.

Please note, the starting address depends upon which controller is being used.

Only use a DMX cable and 3-pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another.

Occupation of the XLR connection:

DMX-output XLR mounting-socket:

1: Ground 2: Signal (−) 3: Signal (+)

DMX-input XLR mounting-plug:

1: Ground 2: Signal (−) 3: Signal (+)

If you are using controllers with this occupation, you can connect the DMX output of the controller directly with the DMX input of the first device in the DMX chain. If you wish to connect DMX controllers with other XLR outputs, you need to use adapter cables.

Building a serial DMX chain:

Connect the DMX output of the first device in the DMX chain with the DMX input of the next device. Always connect one output with the input of the next device until all devices are connected.

Caution: At the last fixture, the DMX cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (−) and Signal (+) in the DMX output of the last fixture.

OPERATION

After you connected the device to the mains, the device starts running.

The LED display lights up and you can now choose the desired settings via the buttons MENU, UP, DOWN and ENTER.

The device has two operating modes. The wind speed of the fan can be adjusted in stand-alone mode via the rotary control or in DMX-controlled mode via any standard DMX controller.

Menu structure

The main menu is accessed by pressing Menu until the display is lit. Browse through the menu by pressing Menu. Press Enter in order to select the desired menu. You can change the selection by pressing Up or Down. Press Enter in order to confirm. You can leave every mode by pressing Menu. The functions provided are described in the following sections.

Mode	Display		Function
Wind speed	SPed 000 - 099		Wind output - from off (000) to maximum (099)
DMX mode	Addr	d001-512 DMX start address setting
Fan, hold	bLNd	on oFF hoLd	Fan on Fan off Keeps the last DMX setting if there is no longer data being received at the DMX-input
Display turn off	dISP	on 10oF 30oF 60oF	Display turn off when the buttons are inactive on - Display always on. xxoF - Shuts off the display after about 10, 30 or 60 seconds
Software version	uer uxxx Software version

English

Adjusting wind speed via rotary control

Set the rotary control to MIN. Connect the effect to the mains.

Use the rotary control to adjust the desired wind output from OFF/minimum (MIN) to maximum (MAX). The setting is indicated on the display.

000 - OFF

001 - 099 (minimum 20% - maximum 100%)

After operation, set the rotary control to position MIN to switch off the unit.

DMX-controlled operation

You can control the device individually via your DMX-controller. The machine uses one DMX channel for adjusting the fan speed.

Addressing

The Control Board allows you to assign the DMX starting address, which is defined as the first channel from which the device will respond to the controller.

Addr	d001-512 DMX start address setting

Please, be sure that you don't have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX-chain.

If several devices are addressed similarly, they will work synchronically.

Press the MENU button until the display shows "Addr". Press ENTER to confirm. You can now set the desired DMX starting address via the UP or DOWN buttons. Press ENTER to confirm.

After having addressed the device, you may now start operating it via your lighting controller.

Note:

After switching on, the device will automatically detect whether DMX 512 data is received or not. If the data is received at the DMX-input, a dot or the display will flash. If there is no data received at the DMX-input, neither the dot nor the display will flash.

This situation can occur if:

• the XLR plug (cable with DMX signal from controller) is not connected with the input of the device.
• the controller is switched off or defective.
• the cable or connector is defective or the signal wires are swap in the input connector.

DMX protocol

Wind speed

Value Feature
0	2 Fan Off
3	255	Wind speed up linearly (minimum 20% - maximum 100%)

CLEANING AND MAINTENANCE

DANGER TO LIFE!

Disconnect from mains before starting maintenance operation!

We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use alcohol or solvents!

There are no serviceable parts inside the device except for the fuse. Maintenance and service operations are only to be carried out by authorized dealers.

Replacing the fuse

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Unscrew the fuse-holder on the rear panel with a fitting screwdriver from the housing (anti-clockwise).
Step 2: Remove the old fuse from the fuse-holder.
Step 3: Install the new fuse in the fuse-holder.
Step 4: Replace the fuse-holder in the housing and fix it.

Should you need any spare parts, please use genuine parts.

If the power supply cable of this device becomes damaged, it has to be replaced by authorized dealers only in order to avoid hazards.

Should you have further questions, please contact your dealer.

TECHNICAL SPECIFICATIONS

Power supply: 230 V AC, 50 Hz
Power consumption: 170 W
Fan Diameter: 310 mm
Maximum Speed: 2600 RPM
Maximum Airflow: 55 m^3/min
DMX channels: 1
DMX connection: 3-pin XLR
Dimensions (L x W x H): 480 x 420 x 500 mm
Weight: 7.3 kg
Accessory:
EUROLITE DMX cable XLR 3pin 3m bk No. 3022785H
PSSO DMX cable XLR 3pin 3m bk Neutrik No. 30227810
SOMMER CABLE DMX cable XLR 3pin 3m bk Hicon No. 30307457
SOMMER CABLE DMX cable XLR 3pin 3m bk Neutrik	No. 3030746Z

Please note: All information is subject to change without prior notice. 20.02.2018 ©