STELLA - Uncategorized Madrix - Free user manual and instructions
Find the device manual for free STELLA Madrix in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Par Can / Wash Light |
| Brand | Madrix |
| Model | STELLA |
| Dimensions (L x W x H) | 10.2 x 8.5 x 10.2 inches (260 x 215 x 260 mm) |
| Weight | 5.5 lbs (2.5 kg) |
| Power Supply | AC 100-240V, 50/60Hz, 30W |
| Light Source | 7x 15W RGBW LEDs |
| Beam Angle | 25° |
| Control Protocol | DMX512, 4/7/12 channels |
| Operating Modes | DMX, Master/Slave, Sound Active, Auto |
| Housing Material | Aluminum die-cast |
| IP Rating | IP20 (indoor use) |
| Cooling | Passive convection |
| Safety Features | Overheat protection, safety cable attachment point |
| Cleaning Instructions | Wipe with dry cloth; avoid solvents or abrasive cleaners |
| Spare Parts Availability | LED modules, power supply, control board can be replaced by qualified technician |
| Repairability | Modular design; serviceable by authorized centers |
| Manual Languages | English (DE also available) |
| Warranty | 2 years limited |
Frequently Asked Questions - STELLA Madrix
How do I set the DMX address on the STELLA fixture?
Use the DMX Address buttons on the rear panel. Press Menu until Addr appears, then use Up/Down to select the desired address (1-512). Press Enter to save.
What is the recommended power cable rating?
Use a power cable rated for at least 10A and 250V with a grounded plug. Ensure the cable is undamaged and suitable for indoor use.
Can I use STELLA outdoors?
No, the STELLA has an IP20 rating, meaning it is only suitable for indoor use. Avoid exposure to rain, moisture, or dust.
How do I clean the lens?
Turn off and unplug the fixture. Wipe the lens gently with a soft, dry cloth. For stubborn dirt, use a slightly damp cloth with mild soap, then dry immediately. Do not use alcohol or abrasive cleaners.
The fixture does not respond to DMX. What should I check?
Verify the DMX cable is connected properly and not faulty. Check that the DMX address matches the controller. Ensure the fixture is in DMX mode (not Master/Slave or Auto). Try replacing the cable or testing with another fixture.
What is the maximum number of units I can daisy-chain?
You can daisy-chain up to 32 STELLA fixtures using a 5-pin DMX cable. For longer runs, use a DMX signal amplifier to maintain signal integrity.
How do I update the firmware?
Firmware updates are performed via a USB connection using Madrix's Updater Tool. Download the latest firmware from the official website, connect the fixture to your computer, and follow the instructions in the tool.
Can I replace the LED module myself?
LED module replacement should only be done by a qualified technician to avoid damaging the fixture or voiding the warranty. Contact an authorized service center for assistance.
What does the 'Sound Active' mode do?
In Sound Active mode, the fixture responds to ambient music or sound via its built-in microphone. The colors and patterns change rhythmically with the beat. Adjust sensitivity using the Sens menu option.
Why is the fan not spinning?
The STELLA uses passive convection cooling and has no fan. If the fixture overheats, it will automatically reduce brightness or shut down. Ensure adequate ventilation around the unit.
User questions about STELLA Madrix
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual STELLA - Madrix and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. STELLA by Madrix.