QB201A - Subwoofer MB QUART - Free user manual and instructions

Product Type	Active Subwoofer System
Subwoofer Size	20 cm (8")
Output Power RMS	125 Watts
Output Power Max	250 Watts
Lowpass Filter	50 - 150 Hz
Phase Shift	0°/180°
Bass Boost	0 - 12 dB
Input Sensitivity	10 V - 0.2 V
Operating Voltage	+12 V (9 - 15 V), negative ground
Fuse Rating	25 A
Dimensions (W x H x L)	240 x 73 x 325 mm
Mounting Brackets Included	Yes (4 brackets, 8 screws)
Input Types	RCA and High Level (speaker wire)
Remote Bass Control	Included (wired remote)
Auto Turn-On Function	Yes, via DC Offset on High Level input
Protection Circuit	Thermal protection (LED indicator)
Cooling	Radiated heat; requires air circulation
Disposal	Do not dispose with household waste; recycle at appropriate facility

Frequently Asked Questions - QB201A MB QUART

How do I turn on the QB201A subwoofer if my head unit has no remote turn-on wire?

The QB201A features an Auto Turn-On function that detects a voltage rise (DC offset) on the High Level input when the head unit is switched on. Ensure the Auto Turn-On switch on the device is set to ON and connect the speaker wires to the High Level input. The amplifier will turn on automatically with the head unit.

What should I do if the PROTECT LED lights up?

The PROTECT LED indicates the device is overheated due to high power levels without adequate airflow. Turn off the system and allow the amplifier to cool down. Ensure proper ventilation around the subwoofer. If the problem persists, check the vehicle's charging system voltage.

Can I use both RCA and High Level inputs simultaneously?

No, never use both the RCA inputs and the High Level input at the same time. Doing so may seriously damage the device. Choose one input type depending on your head unit's outputs.

How do I set the input sensitivity correctly?

Set your head unit's volume to about 75% of maximum. Then adjust the INPUT LEVEL controller slowly until you hear a moderate sound without distortion. This ensures optimal signal-to-noise ratio.

What is the purpose of the PHASE switch?

The PHASE switch (0° or 180°) allows you to match the subwoofer's output with the vehicle's interior acoustics and other speakers. Toggle the switch to find the position that gives the loudest and most coherent bass at the listening position.

How do I connect the remote bass level controller?

Plug the included remote controller into the REMOTE CONTROL input on the device. This allows you to adjust the bass level from a convenient location, such as the driver's seat.

What gauge wire is recommended for power and ground?

Use a cable with at least 10 mm² cross-section for the power and ground connections. Suitable cable sets are available from car audio retailers. For the remote turn-on wire, 0.5 mm² is adequate.

Why is there a popping noise when turning on the subwoofer?

This can be caused by a noisy turn-on signal from the head unit. Try disconnecting the input signal; if the noise stops, use a delay turn-on module or a relay to isolate the remote lead from the head unit's output.

How can I reduce engine noise (alternator whine)?

Route all signal cables (RCA, speaker) away from power and ground wires. Ensure all ground connections are to clean, shiny metal. Add a secondary ground cable from the negative battery terminal to the chassis. If needed, test the alternator and battery.

What is the power fuse rating and how to replace it?

The fuse rating is 25 A. If blown, replace with an equivalent 25 A fuse. Always disconnect power before replacing the fuse.

USER MANUAL QB201A MB QUART

Black MBOUART Active Semiconductor System device with speaker grille and control buttons (no visible text or symbols on body)

ACTIVE SUBWOOFER SYSTEM

QB201A

QB251A

ENG USER'S MANUAL....2

IMPORTANT INFORMATIONS

QB201A

Subwoofer 20 cm (8")
Output Power RMS 125 Watts
Output Power Max. 250 Watts
Lowpass Filter 50 - 150 Hz
Phase Shift 0°/180°
Bass Boost 0 - 12 dB
Input Sensitivity 10 V - 0.2 V
Operating Voltage ....+12 V (9 - 15 V), negative ground
Fuse Rating 25 A
Dimensions (W x H x L) 240 x 73 x 325 mm

QB251A

Subwoofer 25 cm (10")
Output Power RMS 150 Watts
Output Power Max. 300 Watts
Lowpass Filter 50 - 150 Hz
Phase Shift 0°/180°
Bass Boost 0 - 12 dB
Input Sensitivity 10 V - 0.2 V
Operating Voltage ....+12 V (9 - 15 V), negative ground
Fuse Rating 25 A
Dimensions (W x H x L)....270 x 78 x 355 mm

All Specifications are subject to change.

10 \~ 90%

DISPOSAL

If you need to dispose the device and its components, please note that no electronic devices may be disposed with the household waste. Dispose the device and its components at an appropriate recycling facility in accordance with local waste regulations. If necessary, consult your local authority or dealer.

IMPORTANT NOTES PRIOR TO INSTALLATION

ATTENTION: Before you start with the installation, disconnect the ground connection from the vehicle's battery in order to prevent short circuits. This guide is an installation aid for a proper installation of the sound system. Please read the following instructions:

• This device is only suited for a 12 volt system in a vehicle with negative ground.
• The radiated heat while operation requires sufficient air circulation at the place of installation.
• Ensure the accessibility of the fuse and the operating elements after installation.
• The reliability and performance of the device depends on the quality of installation.
• Please treat all parts of the sound system and the components of your vehicle with caution.
• Follow under all circumstance the regulations of the vehicle manufacturer and do not make any modifications on the vehicle, which could interfere the driving safety.

INSTALLATION

Choose a suitable location for your device. The permanent temperature of the location should not be lower than 5^ C and not higher than 50^ C. Protect the device from moisture and humidity. Ensure that your device will not get loose during the drive and hurt someone in the passenger cabin. Use therefor the included mounting brackets (4 x) and screws (8 x). Then use self-tapping screws (not included) from the specialist trade, to fix the device in your vehicle.

Please observe not to damage any serial components of your vehicle (air bags, wires, gas tank etc.) during the installation of your device by drilling or any other operations.

INTERCONNECTION

POWER SUPPLY AND TURN-ON-CONNECTION

First connect the GND terminal (3) of the device to an appropriate ground connection at the chassis. To ensure a good connection, remove dirt and dust from the connection point. A loose connection may cause malfunctions or interferences noise and distortion.

Use at least a 10 mm ^2 cross-section for the power and ground connection cable. Suitable cable sets are available at the specialist shop.

Then connect the +12 V terminal (2) of the device with the battery by using an appropriate cable including an in-line fuse. This fuse should be located very close to the battery; for safety reasons not more than 30 cm away. Only insert the fuse when the installation has been accomplished.

Then connect the remote turn-on-wire from the head unit with the device's REM terminal (1). A cable with a cross-section of 0.5 mm² is adequate.

AUTO-TURN-ON FUNCTION

The amplifier detects a voltage rise (6 Volts) with a so called "DC Offset" over the connected input signal on the HIGH LEVEL input (5) when the head unit will be switched on. Hence, the amplifier will also be turned on. As soon as the head unit will be turned off, the amplifier turns also automatically off. In this case the turn-on connection at REM (1) is not needed, if the switch (5) is in position ON.

Note: The Auto Turn On-function usually works with 90% of all head units, because they are equipped with "High Power"-outputs. Only with a few older and still existing head units the Auto Turn On-function is not working.

FUSE

Fuse with a rating of 25 A (4). If the fuse is defective, please replace with an equivalent fuse.

INTERCONNECTION

PROTECTION CIRCUIT

If the POWER LED (4) lits up, the device is in normal operation. If the PROTECT LED (3) lits up, the device is overheated. If this occurs, the internal built-in protection circuit shuts down the device automatically. The device should work again properly after cooling down.

AUDIO SIGNAL CABLES

Connect the audio signal cables from the RCA outputs of the head unit to the RCA inputs on the device (1).

HIGH LEVEL INPUT

The HIGH LEVEL input (2) is suitable to connect the device input with speaker wires, if your head unit is not equipped with pre-amplifier RCA outputs. Extend therefore every regarding speaker cable from your head unit with appropriate speaker cables from your car audio retailer to the mounting location of the amplifier. Then connect the each matching loudspeaker cable with the cables of the included HIGH LEVEL input jack.

NOTE: Never use the HIGH LEVEL input (2) and the RCA inputs (1) at the same time. This may damage the device seriously.

OPERATING ELEMENTS

INPUT SENSITIVITY

Turn the volume controller of your head unit to the center medium position and then turn up the INPUT LEVEL controller (2) until you have an average medium level without distortion. This setting usually provides sufficient power reserves at optimum weighted signal-to-noise ratio.

LOWPASS FILTER

Set the desired crossover frequency of the low pass filter by using the LOW PASS controller (4). Hence, only the frequencies below the chosen crossover frequency will be amplified and the subwoofer plays more precisely and efficient.

BASS BOOST

By using the BASS BOOST controller (3) you are able to increase the bass boost level from 0 dB to 12 dB. Caution: Please use the bass boost with care.

Connect the included Bass Level Remote Controller at the REMOTE CONTROL input (1). This allows you to control the bass level f.e. out of the driver's seat.

PHASE

The PHASE switch (5) allows you to set the phase between 0^ or 180^ to match the output signal with the vehicle's interior acoustic and the loudspeakers of the sound system.

TROUBLE SHOOTING

If you are having problems after installation follow the trouble shooting procedures below.

Procedure 1:

Check the device for proper connections.

Verify that POWER LED is on. If POWER LED is on skip to Step 3, if not continue.

1. Check the fuse of the device or the external fuse on battery positive cable. Replace if necessary.
2. Verify that Ground connection is connected to clean metal on the vehicle's chassis. Repair/replace if necessary.
   Please ensure that you have reconnected the GND connection at the battery after the installation.
3. Verify that there are 9 to 16 Volts present at the positive battery and remote turn-on cable. Verify quality connections for both cables at device, head unit and battery/fuse holder. Repair/replace if necessary. Check that the vehicle charging system is maintaining proper voltage.

Procedure 2:

PROTECTION LED is on.

1. If the PROTECTION LED is on, this is a sign of driving the device at very high power levels without adequate airflow around the device.
   Shut off the system and allow device to cool down. If the previous items do not solve the problem, a fault may be in the device.
   Check that the vehicle charging system is maintaining proper voltage.

Procedure 3:

Check the device for a proper audio signal.

1. Verify good RCA input connections at head unit and device. Check entire length of cables for kinks, splices, etc.

Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.

1. Use another audio source for testing to provide an audio signal to the Line Input.

Procedure 4:

Check the device for a popping noise while turning on.

1. Disconnect input signal to device and turn device on and off.
2. If the noise is eliminated, connect the REMOTE lead of device to source unit with a delay turn-on module.

OR

1. Use a different 12 Volt source for REMOTE lead of the device (e.g. battery direct just for testing).
2. If the noise is eliminated, use a relay to isolate the device from noisy turn-on output.
3. Don't connect REMOTE directly to the battery after testing to avoid a discharge of the battery.

Procedure 5:

Check the device if you experience excess Engine Noise.

1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.

OR

1. Bypass any and all electrical components between the head unit and the device. Connect the head unit directly to input of the device. If noise goes away the unit being bypassed is the cause of the noise.

OR

1. Use another audio source for testing to provide an audio signal to the Line Input.

OR

1. Remove existing ground wires for all electrical components. Reground wires to different locations. Verify that grounding location is clean, shiny metal free of paint, rust etc.

OR

1. Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

OR

1. Have alternator and battery load tested by your mechanic. Verify good working order of vehicle electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.

WICHTIGE INFORMATIONEN

QB201A