P1560Bi - Video projector ACER - Free user manual and instructions
Find the device manual for free P1560Bi ACER in PDF.
| Product Type | Video Projector |
| Brand | Acer |
| Model | P1560Bi |
| Display Technology | DLP |
| Resolution | XGA (1024 x 768) |
| Brightness | 3600 ANSI Lumens |
| Contrast Ratio | 20,000:1 |
| Lamp Type | UHP Lamp |
| Lamp Life (Normal/ECO) | 5,000 / 10,000 hours |
| Lens Zoom | 1.1x Manual Zoom |
| Keystone Correction | Vertical ±40° |
| Input Interfaces | HDMI, VGA, Composite, S-Video, USB (Service) |
| Dimensions (W x D x H) | 314 x 220 x 117 mm |
| Weight | 2.6 kg |
| Power Consumption | 260W (ECO mode: 210W) |
| Power Supply | AC 100-240V, 50/60Hz |
| Noise Level (Normal/ECO) | 31 / 26 dBA |
| Speakers | Built-in 3W Monaural |
| Projection Mode | Front, Rear, Ceiling |
| Aspect Ratio | 4:3 (Native), 16:9 Compatible |
| Remote Control | Included (IR) |
| Included Accessories | Power Cord, VGA Cable, Remote Control, Batteries, Quick Guide, Lens Cap |
Frequently Asked Questions - P1560Bi ACER
User questions about P1560Bi ACER
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Video projector in PDF format for free! Find your manual P1560Bi - ACER and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. P1560Bi by ACER.
USER MANUAL P1560Bi ACER
DX431Ei/BS-331K/P1360WBTi/FWX1902/
P1260Bi/D711Ei/EV-X71Ki/X1225Pi/
DX231Ei/BS-131K/P1260BTi/FNX1903/
P1160Bi/D701Ei/EV-S71Ki/X1125Pi/DX131Ei/
BS-031K/P1160BTi/FSV1904
User's Guide
Copyright © 2019. Acer Incorporated. All Rights Reserved.
Acer Projector User's Guide Original Issue: 12/2019
Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose.
Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your projector. All correspondence concerning your unit should include the serial number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated.
Model number: ____
Serial number: ____
Date of purchase: ____
Place of purchase: ____
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product names or trademarks are used herein for identification purposes only and belong to their respective companies.
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
Information for your safety and comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the external power supply unit:
• Install the power supply unit before connecting the power cord to the AC power outlet.
- Unplug the power cord before removing the power supply unit from the projector.
- If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet.
Warnings!
- Do not use this product near water.
- Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged.
- Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface.
- This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.
- Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
- To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface.
- Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, lamp.
Using electrical power
- This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
- Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord.
- If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.
- Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip's input rating.
- This product's AC adapter is equipped with a three-wire grounded plug. The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product.
- Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:
• the power cord or plug is damaged, cut or frayed
- liquid was spilled into the product
•the product was exposed to rain or water
•the product has been dropped or the case has been damaged
•the product exhibits a distinct change in performance, indicating a need for service
•the product does not operate normally after following the operating instructions
Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
Additional safety information
- Do not look into the projector's lens when the lamp is on. The bright may hurt your eyes.
- Turn on the projector first and then signal sources
- Do not place the product in following environments:
• Space that is poorly ventilated or confined. At least 50cm clearance from walls
- and free flow of air around the projector is necessary.
- Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the life span and darkening the image.
- Locations near fire alarms.
- Locations with an ambient temperature above 40 oC/104 oF.
- Locations where the altitudes are higher than 10000 feet.
- Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and contact your dealer.
- Do not keep using this product to break or drop it. In this case contact your dealer for inspection.
- Do not face the projector lens to the sun. It can lead to fire.
- When switching the projector off, suggest to ensure the projector completes its cooling cycle before disconnecting power.
- Do not frequently turn off the main power abruptly or unplug the projector during operation. The best way is to wait for the fan to turn off before turning main power off..
vi
- Do not touch air outlet grille and bottom plate which becomes hot.
- Do not look into the air outlet grille when projector is operating. It may hurt your eyes.
• Always open the lens shutter or remove the lens cap when the projector is on.
- Do not block the projector lens with any object when the projector is under operation as this could cause the object to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press HIDE on the remote control.
- The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
- Do not operate lamps beyond the rated lamp life. It could cause it to break on rare occasions.
- Never replace the lamp assembly or any electronic components unless the projector is unplugged.
- The product will detect the life of the lamp itself. Please be sure to change the lamp when is showing warning message.
- When changing the lamp, please allow unit to cool down, and follow all changing instructions.
- Reset the "Lamp Hour Reset" function from the Onscreen display "Management > Lamp Settings" menu after replacing the lamp module.
- Do not attempt to disassemble this projector. There are dangerous high voltages inside which may hurt you. The only user serviceable part is the lamp which has its own removable cover. Refer servicing only to suitable qualified professional service personnel.
- Do not stand the projector on end vertically. It may cause the projector to fall over, causing injury or damage.
- This product is capable of displaying inverted images for ceiling mount installation. Only use acer ceiling mount kit for mounting the projector and ensure it is securely installed.
- The projector should be placed in a horizontal way by means of desktop or ceiling mount mode only, and its tilt angles should not exceed 20 degrees, otherwise it would cause dramatical decrease of lamp life or severe safety concern of system malfunction.
natural_image
Diagram showing two mechanical components with green spheres and angular measurements (20°), no text or symbols present.
natural_image
Two identical diagrams showing a red circle on a black object, with no text or symbols present.Caution for Listening
To protect your hearing, follow these instructions.
- Increase the volume gradually until you can hear clearly and comfortably.
- Do not increase the volume level after your ears have adjusted.
- Do not listen to music at high volumes for extended periods.
- Do not increase the volume to block out noisy surroundings.
•Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
"Lamp(s) contain Mercury, Dispose Properly."
Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal information, check www.lamprecycle.org
Do not stare into the beam, RG2
"As with any bright source, do not stare into the direct beam, RG2 IEC 62471-5:2015"
viii
First things first
Usage Notes
Do:
- Turn off the product before cleaning.
- Use a soft cloth moistened with mild detergent to clean the display housing.
- Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Don't:
- Block the slots and openings on the unit provided for ventilation.
- Use abrasive cleaners, waxes or solvents to clean the unit.
- Use under the following conditions:
•In extremely hot, cold or humid environments.
•In areas susceptible to excessive dust and dirt.
- Near any appliance that generates a strong magnetic field.
- Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user's guide to maximize the life of your unit.
Warning:
- Do not look into the projector's lens when the lamp is on. The bright light may hurt your eyes.
• To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. - Please do not open or disassemble the product as this may cause electric shock.
- When changing the lamp, please allow unit to cool down, and follow all changing instructions.
- This product will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages.
- Reset the "Lamp Hour Reset" function from the Onscreen display "Management > Lamp Settings" menu after replacing the lamp module.
- When switching the projector off, please ensure the projector completes its cooling cycle before disconnecting power.
- Turn on the projector first and then the signal sources.
- Do not use lens cap when projector is in operation.
- When the lamp reaches the end of its life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under "Replacing the Lamp".
Information for your safety and comfort iii
First things first viii
Usage Notes viii
Precautions viii
Introduction 1
Product Features 1
Package Overview 2
Projector Overview 3
Projector Outlook 3
Control Panel 4
Remote Control Layout 5
Getting Started 7
Connecting the Projector 7
Turning the Projector On/Off 8
Turning on the Projector 8
Turning the projector off 9
Adjusting the Projected Image 10
Adjusting the Height of Projected Image 10
How to optimize image size and distance 11
How to get a preferred image size by adjusting distance and zoom 15
User Controls 19
Onscreen Display (OSD) Menus 19
Color 20
Image 22
Source 23
Setting 23
Management 25
Information 26
Acer LAN webpage management 27
How to login in 27
System Status 28
Change Password 28
Projector Control Panel 29
Network Setting 29
Crestron Setting (optional) 29
Appendices 30
Troubleshooting 30
LED & Alarm Definition Listing 31
Replacing the Lamp 32
Ceiling Mount Installation 33
Specifications 36
Compatibility modes 38
Regulations and safety notices 40
Introduction
Product Features
This product is a single-chip DLP ^® projector. Outstanding features include:
•DLP ^® technology
•Auto/4:3/16:9/16:10 aspect ratio supported
- Enables projecting 3D content via DLP Link Technology
- Acer ColorBoost technology delivers nature's true colors for vivid, life-like images
•High brightness and contrast ratio
- Acer LumiSense technology can intelligently optimize the brightness and color saturation of projected image based on actual ambient light
- Acer BluelightShield™ reduces the exposure ratio of blue light, which can potentially cause long-term eye damage, by adjusting color hue and brightness
- Versatile display modes (Bright, Presentation, Standard, Video, User, 3D) enable optimum performance in any situation
•HDTV (480i/p, 576i/p, 720p, 1080i/p) supported
- Lower power consumption and economy (ECO) mode extends lamp life
- Acer EcoProjection Technology delivers Intelligent power management approach and physical efficiency improvement
• Equipped with HDMI™ connection supporting HDCP
• Advanced digital keystone correction optimizes presentations
- Smart detection delivers quick, intelligent source detection
- Multi-language onscreen display (OSD) menus
- Manual focus projection lens zooms up to 1.2x
- 1.8X digital zoom
- Microsoft ^ Windows ^ XP, Windows 7, Windows 8.0, Windows 8.1, Windows 10, Macintosh ^ OS compliant
Note: Functions vary depending on model definition.
Package Overview
This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing.
Projector Power cord VGA cable (option)
2 x Batteries Quick start guide (projector) Remote control
Quick start guide (Media/Wireless function)
WirelessProjection-Kit (option)
CastMaster-Kit (option)
Projector Overview
Projector Outlook
Front / upper side
| # Description # Description | ||
| 1 Control panel 7 Adjuster foot | ||
| 2 Focus ring 8 Air outlet | ||
| 3 Zoom ring 9 Security bar | ||
| 4 Remote control receiver 10 Lamp cover | ||
| 5 Projection lens 11 Air inlet | ||
| 6 Quick-release lever |
Rear / Left side
| # Description # Description | ||
| 1 Speaker 8 LAN (RJ45 Port for 10/100M Ethernet) | ||
| 2 Mini USB connector 9 USB connector (5V/1.5A) | ||
| 3 RS 232 connector 10 | Monitor loop-through output connector (VGA OUT) | |
| 4 PC analog signal/HDTV/component video input connector (VGA IN) | 11 | Power socket |
| 5 USB connector (WIRELESS KIT) 12 | Audio output connector | |
| 6 HDMI input connector 13 | Kensington anti-theft lock slot | |
| 7 Audio input connector | ||
Control Panel
flowchart
graph TD
1["1"] --> HOURS
2["2"] --> TEMP
3["3"] --> LAMP
HOURS --> 4
TEMP --> 5
LAMP --> 6
4 --> SOURCE
5 --> SOURCE
6 --> ENTER
7 --> MODE
8 --> MODE
9 --> ENTER
10 --> MODE
7 --> RSYNC
11 --> BACK
12 --> MENU
13 --> RSYNC
| # Icon Function Description | ||
| 1 POWER Power Indicator LED | ||
| 2 TEMP Temp | Indicator LED | |
| 3 LAMP Lamp | Indicator LED | |
| 4 POWER See | the contents in "Turning the Projector On/Off" section. | |
| 5 SOURCE Changes the active source, short press the button. | ||
| 6 VOLUME Adjusts the sound level. | ||
| 7 KEYSTONE | Adjusts the image to compensate for distortion caused by tilting the projector (± 30 degrees). | |
| 8 Four directional select keys | Use up, down, left, right buttons to select items or make adjustments to your selection. | |
| 9 ENTER Confirm your selection of items. | ||
| 10 MODE Press "MODE" to select the display mode from Bright, Presentation, Standard, Video, User 1 and User 2. | ||
| 11 BACK Go back to the previous menu or exit function. | ||
| 12 MENU Press "MENU" to launch the onscreen display(OSD) menu or exit the OSD menu. | ||
| 13 RESYNC | Automatically determines the best picture timings for the displayed image | |
Remote Control Layout
| # Icon Function Description | |||||
| 1 Infrared | transmitter | Sends signals to the projector. | |||
| 2 |  | POWER | Refer to the "Turning the Projector On/Off" section. | ||
| 3 FREE To | pause the screen image. | ||||
| 4 Four |  | directional select keys | Use up, down, left, right buttons to select items or make adjustments to your selection. | ||
| 5 3D Only available for 3D input signal. | |||||
| 6 BACK Go back to the previous menu or exit function. | |||||
| 7 RATIO To choose the desired aspect ratio. | |||||
| 8 ZOOMZooms in or out the projector display. | |||||
| 9 PAGE | •For computer mode. Use this button to select the next or previous page. This function is available when USB Ctrl connector (mini type B) is connected to a computer via a USB cable.•Use this button to select the next or previous page in Media mode. | ||||
| # | Icon | Function | Description | ||
| 10 | VGA | Press "VGA" to change source to the VGA connector. | |||
| 11 HDMI To | change source to HDMI. | ||||
| 12 RESYNC | Automatically de | termines the best picture timings for the displayed image. | |||
| 13 SOURCE Changes the active source. | |||||
| 14 HI DE Mo | mentarily turns off the video. Press "HIDE" to hide the image, press again to display the image. | ||||
| 15 KEY [8053]ONE [806A] | NE Adjusts the im | age to compensate for distortion caused by tilting the projector (± 30 degrees). | |||
| 16 Ent [2K84]on confirm your selection of items. | |||||
| Play/Pause No function. | |||||
| 17 MUTE To turn on/off AV mute. | |||||
| 18 MENU Press "MENU" to launch the onscreen display (OSD) menu or exit the OSD menu. | |||||
| 19 MODE Press "MODE" to select the display mode from Bright, Presentation, Standard, Video, User 1 and User 2. | |||||
20 Vol  UP/Down | Increases or decreases the volume. | ||||
| 21 MEDIA Press "MEDIA" to go to the home page of media mode. | |||||
| 22 LAN/WiFi Press "LAN/WiFi" to go to the home page of LAN/WiFi mode. | |||||
| 23 INFO Displays the status in information of the projector. | |||||
Note: Functions vary depending on model definition.
Getting Started
Connecting the Projector
flowchart
graph TD
A["Device 1"] --> B["USB"]
B --> C["Device 3"]
C --> D["Device 5"]
D --> E["Device 6"]
E --> F["Device 7"]
F --> G["Device 8"]
G --> H["Device 9"]
H --> I["Device 10"]
I --> J["Device 11"]
J --> K["Device 12"]
K --> L["Device 12"]
L --> M["Device 12"]
M --> N["Device 12"]
N --> O["Device 12"]
O --> P["Device 12"]
P --> Q["Device 12"]
Q --> R["Device 12"]
R --> S["Device 12"]
S --> T["Device 12"]
T --> U["Device 12"]
U --> V["Device 12"]
V --> W["Device 12"]
W --> X["Device 12"]
X --> Y["Device 12"]
Y --> Z["Device 12"]
Z --> AA["Device 12"]
AA --> AB["Device 12"]
AB --> AC["Device 12"]
AC --> AD["Device 12"]
AD --> AE["Device 12"]
AE --> AF["Device 12"]
AF --> AG["Device 12"]
AG --> AH["Device 12"]
AH --> AI["Device 12"]
AI --> AJ["Device 12"]
AJ --> AK["Device 12"]
AK --> AL["Device 12"]
AL --> AM["Device 12"]
AM --> AN["Device 12"]
AN --> AO["Device 12"]
AO --> AP["Device 12"]
AP --> AQ["Device 12"]
AQ --> AR["Device 12"]
AR --> AS["Device 12"]
AS --> AT["Device 12"]
AT --> AU["Device 12"]
AU --> AV["Device 12"]
AV --> AW["Device 12"]
AW --> AX["Device 12"]
AX --> AY["Device 12"]
| # Description # Description | ||
| 1 Power cord 7 Audio cable Jack/Jack | ||
| 2 VGA cable 8 LAN cable | ||
| 3 RS232 cable 9 USB cable for charging device | ||
| 4 USB cable (mini-B to type A) 10 USB flash drive | ||
| 5 Component Video to VGA (DSub) adapter cable | 11 Audio cable jack/RCA | |
| 6 HDMI cable 12 Wireless dongle |
Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector.
Note: Functions vary depending on model definition.
Note: USB cable needs powered extender if the length is over 5 m.
Turning the Projector On/Off
Turning on the Projector
1 Ensure that the power cord and signal cable are securely connected. The Power indicator LED will turn orange.
2 Turn on the projector by pressing "Power" button on the control panel or remote control, and the Power indicator LED will flash green.
3 Turn on your source (computer, notebook, video player, etc.). The projector will detect your source automatically.
- If the screen displays "No Signal", please make sure the signal cables are securely connected.
- If you connect to multiple sources at the same time, use the "Source" button on the remote control or direct source key on the remote control to switch between inputs.
Turning the projector off
1 To turn the projector off, press and hold the power button. This message appears: "Press ⏻ again to Standby mode." Press the power button again.
2 The LED power indicator will flash orange after the projector is turned off, and the fan(s) will continue to operate to ensure that the system cools properly.
3 Once the system has finished cooling, the LED power indicator will stop blinking and turn solid orange to indicate standby mode.
4 It is now safe to unplug the power cord.
Note: Whenever the projector automatically shuts down and the LED lamp indicator turns solid red, contact your local reseller or service center.
Note: Functions vary depending on model definition.
Adjusting the Projected Image
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
1 Pull the quick-release lever and lift the front of the projector. Once the image is positioned where you want it, release the quick-release lever to lock the foot in position. You may also screw the front adjuster foot to change the image height.
2 Screw the rear adjuster feet to fine tune the horizontal angle.
natural_image
Diagram of a hand operating a camera with three circular indicators below indicating rotational or directional movement (no text or symbols present)Adjuster feet
How to optimize image size and distance
•SVGA series
Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen.
If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 42" and 50".
Note: Remind as below figure, the space of 87 cm height is required when located at 2.0 m distance.
| Desired Distance (m) | Screen size | Top | Screen size | Top | ||
| (Min zoom) (Max zoom) | ||||||
| Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | |
| 1.6 34 | 69 x 52 60 | 41 82 x 62 71 | ||||
| 2 42 8 | 6 x 64 74 | 50 102 x 77 87 | ||||
| 2.5 52 | 106 x 80 90 | 63 127 x 95 107 | ||||
| 3 | 63 | 127 x 95 | 107 | 75 | 152 x 114 | 127 |
| 3.5 | 73 | 148 x 111 | 124 | 87 | 177 x 133 | 147 |
| 4 | 83 | 169 x 127 | 140 | 99 | 202 x 151 | 167 |
| 4.5 | 93 | 190 x 142 | 157 | 112 | 227 x 170 | 186 |
| 5 | 104 | 210 x 158 | 173 | 124 | 252 x 189 | 206 |
| 6 | 124 | 252 x 189 | 207 | 148 | 301 x 226 | 246 |
| 7 | 144 | 294 x 220 | 240 | 173 | 351 x 263 | 286 |
| 8 | 165 | 335 x 251 | 273 | 197 | 401 x 301 | 326 |
| 9 | 185 | 377 x 283 | 306 | 222 | 451 x 338 | 365 |
| 10 | 206 | 418 x 314 | 340 | 246 | 500 x 375 | 405 |
| 11 | 226 | 460 x 345 | 373 | 271 | 550 x 413 | 445 |
| 12.2 | 251 | 510 x 382 | 413 | 300 | 610 x 457 | 493 |
Zoom Ratio: 1.2x
•XGA series
Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen.
If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 43" and 51".
Note: Remind as below figure, the space of 88 cm height is required when located at 2.0 m distance.
| Desired Distance (m) | Screen size | Top | Screen size | Top | ||
| (Min zoom) (Max zoom) | ||||||
| Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | |
| 1.6 34 | 70 x 52 61 | 41 83 x 63 72 | ||||
| 2 43 8 | 7 x 65 74 | 51 103 x 78 88 | ||||
| 2.5 53 | 108 x 81 9 | 1 63 129 x 96 107 | ||||
| 3 | 63 | 129 x 96 | 107 | 76 | 154 x 115 | 127 |
| 3.5 | 74 | 150 x 112 | 124 | 88 | 179 x 134 | 147 |
| 4 | 84 | 171 x 128 | 141 | 100 | 204 x 153 | 167 |
| 4.5 | 94 | 192 x 144 | 158 | 113 | 229 x 172 | 187 |
| 5 | 105 | 213 x 159 | 174 | 125 | 254 x 191 | 207 |
| 6 | 125 | 255 x 191 | 208 | 150 | 304 x 228 | 247 |
| 7 | 146 | 297 x 222 | 241 | 174 | 354 x 266 | 287 |
| 8 | 167 | 339 x 254 | 274 | 199 | 405 x 304 | 327 |
| 9 | 187 | 381 x 285 | 308 | 224 | 455 x 341 | 367 |
| 10 | 208 | 423 x 317 | 341 | 249 | 505 x 379 | 407 |
| 11 | 229 | 465 x 348 | 375 | 273 | 555 x 416 | 447 |
| 12.1 | 251 | 511 x 383 | 411 | 300 | 611 x 458 | 491 |
Zoom Ratio: 1.2x
- WXGA series
Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen.
If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 50" and 60".
Note: Remind as below figure, the space of 89 cm height is required when located at 2.0 m distance.
| Desired Distance (m) | Screen size | Top | Screen size | Top | ||
| (Min zoom) (Max zoom) | ||||||
| Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | |
| 1.3 33 | 71 x 45 52 | 40 86 x 53 61 | ||||
| 2 50 | 108 x 68 75 | 60 130 x 81 | 89 | |||
| 2.5 62 | 134 x 84 92 | 75 161 x 101 | 110 | |||
| 3 | 75 | 161 x 100 | 109 | 89 | 192 x 120 | 130 |
| 3.5 | 87 | 187 x 117 | 126 | 104 | 224 x 140 | 150 |
| 4 | 99 | 213 x 133 | 143 | 119 | 255 x 160 | 171 |
| 4.5 | 111 | 239 x 150 | 160 | 133 | 287 x 179 | 191 |
| 5 | 123 | 265 x 166 | 177 | 148 | 318 x 199 | 212 |
| 6 | 148 | 318 x 199 | 211 | 177 | 381 x 238 | 252 |
| 7 | 172 | 370 x 231 | 245 | 206 | 444 x 278 | 293 |
| 8 | 196 | 423 x 264 | 279 | 235 | 507 x 317 | 334 |
| 9 | 221 | 475 x 297 | 314 | 265 | 570 x 356 | 375 |
| 10.2 | 250 | 538 x 336 | 354 | 300 | 645 x 403 | 424 |
Zoom Ratio: 1.2x
•1080p series
Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen.
If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 55" and 66".
Note: Remind as below figure, the space of 93 cm height is required when located at 2.0 m distance.
| Desired Distance (m) | Screen size | Top | Screen size | Top | ||
| (Min zoom) (Max zoom) | ||||||
| Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | Diagonal (inch) | W (cm) x H (cm) | From base to top of image (cm) | |
| 1.2 33 | 74 x 42 50 | 40 89 x 50 59 | ||||
| 2 55 | 21 x 68 78 | 66 146 x 82 93 | ||||
| 2.5 68 | 150 x 85 96 | 82 182 x 102 115 | ||||
| 3 | 81 | 180 x 101 | 113 | 98 | 217 x 122 | 136 |
| 3.5 | 94 | 209 x 118 | 131 | 114 | 253 x 142 | 157 |
| 4 | 108 | 239 x 134 | 149 | 130 | 289 x 162 | 179 |
| 4.5 | 121 | 268 x 151 | 166 | 147 | 324 x 182 | 200 |
| 5 | 134 | 297 x 167 | 184 | 163 | 360 x 202 | 222 |
| 6 | 161 | 356 x 200 | 219 | 195 | 431 x 243 | 264 |
| 7 | 187 | 415 x 233 | 255 | 227 | 503 x 283 | 307 |
| 8 | 214 | 474 x 267 | 290 | 259 | 574 x 323 | 350 |
| 9 | 241 | 533 x 300 | 325 | 291 | 645 x 363 | 393 |
| 9.3 | 249 | 550 x 310 | 336 | 301 | 666 x 375 | 406 |
Zoom Ratio: 1.2x
How to get a preferred image size by adjusting distance and zoom
•SVGA series
The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring.
To obtain an image size of 60" set the projector at a distance 2.4 m and 2.9 m from the screen.
| Desired Image Size Distance (m) Top (cm) | ||||
| Diagonal (inch) | W (cm) x H (cm) | Max zoom | Min zoom | From base to top of image |
| 40 81 x 61 | 1.6 1.9 70 | |||
| 50 102 x 76 | 2.0 2.4 86 | |||
| 60 122 x 91 | 2.4 2.9 103 | |||
| 70 142 x 107 | 2.8 3.4 119 | |||
| 80 163 x 122 | 3.2 3.9 135 | |||
| 90 183 x 137 | 3.6 4.3 151 | |||
| 100 203 x 152 | 4.0 4.8 168 | |||
| 120 244 x 183 | 4.8 5.8 200 | |||
| 150 305 x 229 | 6.1 7.3 249 | |||
| 200 406 x 305 | 8.1 9.7 330 | |||
| 250 508 x 381 | 10.2 12.2 | 411 | ||
| 300 610 x 457 | 12.2 14.6 | 493 | ||
Zoom Ratio: 1.2x
•XGA series
The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring.
To obtain an image size of 60" set the projector at a distance 2.4 m and 2.8 m from the screen.
| Desired Image Size Distance (m) Top (cm) | ||||
| Diagonal (inch) | W (cm) x H (cm) | Max zoom | Min zoom | From base to top of image |
| 40 81 x 61 | 1.6 1.9 70 | |||
| 50 102 x 76 | 2.0 2.4 86 | |||
| 60 122 x 91 | 2.4 2.8 102 | |||
| 70 142 x 107 | 2.8 3.3 118 | |||
| 80 163 x 122 | 3.2 3.8 134 | |||
| 90 183 x 137 | 3.6 4.3 151 | |||
| 100 203 x 152 | 4.0 4.8 167 | |||
| 120 244 x 183 | 4.8 5.7 199 | |||
| 150 305 x 229 | 6.0 7.2 248 | |||
| 200 406 x 305 | 8.0 9.6 328 | |||
| 250 508 x 381 | 10.1 12.0 | 409 | ||
| 300 610 x 457 | 12.1 14.5 | 490 | ||
Zoom Ratio: 1.2x
- WXGA series
The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring.
To obtain an image size of 60" set the projector at a distance 2.0 m and 2.4 m from the screen.
| Desired Image Size Distance (m) Top (cm) | ||||
| Diagonal (inch) | W (cm) x H (cm) | Max zoom | Min zoom | From base to top of image |
| 40 86 x 54 | 1.3 1.6 61 | |||
| 50 108 x 67 | 1.7 2.0 75 | |||
| 60 129 x 81 | 2.0 2.4 89 | |||
| 70 151 x 94 | 2.3 2.8 103 | |||
| 80 172 x 108 | 2.7 3.2 117 | |||
| 90 194 x 121 | 3.0 3.6 131 | |||
| 100 215 x 135 | 3.4 4.0 145 | |||
| 120 258 x 162 | 4.0 4.9 173 | |||
| 150 323 x 202 | 5.1 6.1 215 | |||
| 200 431 x 269 | 6.8 8.2 285 | |||
| 250 538 x 337 | 8.5 10.2 355 | |||
| 300 646 x 404 | 10.2 | 12.3 424 | ||
Zoom Ratio: 1.2x
•1080p series
The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring.
To obtain an image size of 60" set the projector at a distance 1.8 m and 2.2 m from the screen.
| Desired Image Size Distance (m) Top (cm) | ||||
| Diagonal (inch) | W (cm) x H (cm) | Max zoom | Min zoom | From base to top of image |
| 40 89 x 50 | 1.2 1.5 58 | |||
| 50 111 x 62 | 1.5 1.8 72 | |||
| 60 133 x 75 | 1.8 2.2 85 | |||
| 70 155 x 87 | 2.1 2.6 98 | |||
| 80 177 x 100 | 2.4 3.0 112 | |||
| 90 199 x 112 | 2.7 3.3 125 | |||
| 100 221 x 125 | 3.1 3.7 138 | |||
| 120 266 x 149 | 3.7 4.5 165 | |||
| 150 332 x 187 | 4.6 5.6 205 | |||
| 200 443 x 249 | 6.2 7.5 271 | |||
| 250 553 x 311 | 7.7 9.4 338 | |||
| 300 664 x 374 | 9.3 11.2 404 | |||
Zoom Ratio: 1.2x
User Controls
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allows you to make image adjustments and change a variety of settings.
Using the OSD menus
• To open the OSD menu, press "MENU" on the remote control.
- When the OSD is displayed, use the keys to select any item in the
main menu. After selecting the desired main menu item, press to enter submenu for feature setting.
- Use the keys to select the desired item and adjust the settings by
using the keys.
- Select the next item to be adjusted in the submenu and adjust as described above.
- Press "BACK" on the remote control, the screen will go back to the previous menu or exit OSD.
- Press "MENU" on the remote control to exit OSD directly. The OSD menu will close and the projector will automatically save the new settings.
Note: Some of the following OSD settings may not be available. Please refer to the actual OSD of your projector.
Note: Functions vary depending on model definition.
Color
| LumiSense | The light sensor of LumiSense+ technology can intelligently optimize the brightness and color saturation of projected image based on actual ambient light. The feature greatly enhances dark detail visibility and color saturation.•Off: For normal mode. (ambient light sensor is off)•Normal: Select "Normal" to meet the visual effect of dark detail enhancement.•Boost: Select "Boost" to meet the visual effect of brightness boost.•Dynamic Black:automatically optimize the display of dark movie scenes enabling them to be shown in incredible detail.: Once LumiSense is enabled, BluelightShield switches to "Off".: Once Dynamic Black is enabled, ECO Mode is grayout. |
| BluelightShield | •Off: Default setting.•Low / Medium / High: Select Low / Medium / High to reduce different exposure levels of blue light dynamically.: Once BluelightShield is enabled, LumiSense switches to "Off". |
| Display Mode | There are many factory presets optimized for various types of images.•Bright: For brightness optimization.•Presentation: For meeting presentation.•Standard: For common environment.•Video: For playing video in a bright environment.•EcoPro: Dims the projector lamp to the very low status which will extend the lamp life to 20,000 hours.•User 1/User 2: Memorize user's settings.•3D: Only available for 3D input signal.: Once EcoPro is enabled, ECO Mode switches to EcoPro at the same time.: After the above setting is done, if user changes to other Dislay mode settings rather than EcoPro, ECO Mode switches to "Off".: When EcoPro is enabled for 4 hours, the projector will switch to the power consumption of ECO mode for 10 minutes, and then switches back to EcoPro mode again. During the period time of ECO mode, the lamp will become brighter. |
| Reference Mode | For user mode settings. |
| Brightness | Adjust the brightness of the image.•Press to darken the image.•Press to lighten the image. |
| Contrast | "Contrast" controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. •Press to decrease the contrast. •Press to increase the contrast. |
| Sharpeness | Adjusts the sharpness of the image. •Press to decrease the sharpness. •Press to increase the sharpness. |
| Brilliant Color | Choose On to enable a greater brightness increase in mid-tone images. |
| Gamma | Effects the representation of dark scenery. With greater gamma value, dark scenery looks brighter. |
| Color Temperature | Use this function to choose CT1, CT2, CT3 mode. |
| Color Temperature Fine Tuning | R Gain Adjusts the red gain for color temperature optimization. |
| G Gain Adjusts the green gain for color temperature optimization. | |
| B Gain Adjusts the blue gain for color temperature optimization. | |
| R Bias Adjusts the red bias for color temperature optimization. | |
| G Bias Adjusts the green bias for color temperature optimization. | |
| B Bias Adjusts the blue bias for color temperature optimization. | |
| C.M.S. | Ind. Color Management Adjusts the red, green, blue, cyan, yellow and magenta colors. |
| Ind. Hue Adjusts the color balance of red and green. | |
| Ind. Saturation Adjusts the selected color to be less or more saturated color. | |
| Ind. Gain Adjusts the selected color's contrast. | |
| Reset Color Setting | Resets current or all display modes to the factory preset settings. |
Note: Functions vary depending on model definition.
Image
| Wall Color Use this | function to choose a proper color according to the wall. There are several choices, including white, light yellow, light blue, pink, dark green. It will compensate the color deviation due to the wall color to show the correct image tone. |
| Aspect Ratio Use this | is function to choose your desired aspect ratio.●Auto: Keep the image with original width-higth ratio and maximize the image to fit native horizontal or vertical pixels.●4:3: The image will be scaled to fit the screen and displayed using a 4:3 ratio.●16:9: The image will be scaled to fit the width of the screen and the height adjusted to display the image using a 16:9 ratio.●16:10: The image will be scaled to fit the width of the screen and the height adjusted to display the image using a 16:10 ratio. |
| H./V. Keystone H. Keystone | Press the ▶ button to adjust image distortion horizontally and makes a squarer image. |
| V. KeystonePress the ▶ button to adjust image distortion vertically and makes a squarer image. | |
| 4 Corner Correction | Press the "ENTER" button to enter 4 Corner Correction page. Press the ▲/▼ to select one of the four corners and then press the "ENTER" button. Press the ▲/▼ to adjust vertical position.Press the ◀/▶ to adjust horizontal position. Press BACK to select other corners. Repeat the same procedure with the positions for the corners. |
| Position Horizontal | Centers the on-screen image by moving it to the left or right.Vertical Centers the on-screen image by moving it up or down. |
| Phase Synchronizes | the signal timing of the projector with the graphics card.If you experience an unstable or flickering image, use this function to correct it. |
| Clock Clock changes | the projector's refresh rate to match the frequency of your computer's graphics card. If you can see a vertical flickering bar in the projected image, use this function to make the necessary adjustments. |
| Digital Zoom Magnifies or reduces the projected image. | |
| 3D(Only available for 3D input signal.) | 3D ModeIf the 3D content is not displayed correctly, you can select a 3D format that suits the 3D content you are viewing and obtain the best result. |
| 3D L/R InvertIf you see a discrete or overlapping image while wearing DLP 3D glasses, you may need to execute "Invert" to get best match of left/right image sequence to get the correct image (for DLP 3D). | |
Source
| Source Selection Manual by source menu, Auto by Smart Detection. | |
| HDMI Color Range | Adjust the color range of the HDMI image data to correct color display error.•Auto: Automatically adjust by information from player.•Limited Range: Prosess the input image as limited color range data.•Full Range: Prosess the input image as full color range data. |
Setting
| Language | Choose the multilingual OSD menu. Use the ▲/▽/ ◀ ▶/key to select your preferred menu language.• Press "ENTER" to confirm the selection. |
| Projection Mode | Front: The factory default setting.Rear: When you select this function, the projector reverses the image so you can project from behind a translucent screen.Ceiling-Rear: When you select this function, the projector reverses and inverts the image at same time. You can project from behind a translucent screen with ceiling mounted projection.Ceiling+Front: When you select this function, the projector inverts the image for ceiling-mounted projection. |
| Menu Settings Menu | Display TimeChoose the OSD menu display time. (Default is 20 seconds). Select "Manual" to turn off main menu/one direct-key menu manually by user. |
| Menu PositionSets the On-Screen Display (OSD) menu position. | |
| Reminder MessageSets whether to display the reminder message. | |
| Operation Settings AC | Power OnChoose "On" to power on projector while AC power plug in. |
| Auto ShutdownThe projector will automatically shutdown when there is no signal input after the allocated time. (default is 15 minutes) | |
| Quick CoolingChoose "On" to turn off the projector in a few seconds. | |
| Control Panel Lock Dis | sables or enables all panel key functions except Power on the projector. |
| Background Allows you | you to select which background color will display when no signal is input into the projector. |
| Startup Screen Use th | is function to select your desired startup screen. If you change the setting, the changes will take effect when you exit the OSD menu. |
| USB 5V (Standby) | Default is "Off". Choose "On" to supply 5V/1.5A pwoer while in standby mode. |
| VGA OUT (Standby) | Default is "Off". Choose "On" to enable VGA OUT connection. |
| Firmware Upgrade Ch | choose to upgrade firmware via USB drive or network. |
Note: Functions vary depending on model definition.
Management
| High Altitude Choose | "On" to turn on High Altitude mode. Operate the fans at full speed continuously to allow for proper high altitude cooling of the projector. |
| Audio Settings Volume | •Press to decrease the volume.•Press to increase the volume. |
| Power On/OffSelect this function to adjust the notification volume when turning the projector on/off. | |
| Lamp Settings Lamp Information | •Lamp TimerDisplays the lamp's elapsed operating time (in hours) including Normal, Eco, and EcoPro.•Lamp LifeDisplays the percentage of the remaining lamp life. |
| Lamp Hour ResetPress the "ENTER" button and choose "Yes" to turn the lamp hour counter to 0 hours. | |
| ECO Mode Choose "On" to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose "Off" to return normal mode. Choose "EcoPro" to dim the projector lamp to the very low status which will extend the lamp life to 20,000 hours. | |
| Security Settings Change PasswordTo set or change password please follow up OSD on-screen steps.If you forget the password, contact your local reseller or service center to decode the number. | |
| Test Pattern Choose "On" to enable the function and the projector displays the test pattern. | |
| Network Settings LAN | N IP / MaskIdentify IP and Mask address. |
| WiFi IP/MaskIdentify IP and Mask address. | |
| MAC AddressIdentify MAC address. | |
| Wake on LAN (Standby)Set to "On" to enable wake-on-LAN function to power on projector via LAN under standby status. It is required to download WOL(wake-on-LAN; WOL) tool or app for PC/Mobile by users for this function. | |
| DHCP•On: Projector will obtain an IP address automatically from your network.Grey out when LAN isn't plugged in and LAN IP X.X.X.X show 0.0.0.0 | |
| LAN ResetReset LAN function. | |
| Reset | Press the "ENTER" button and choose "Yes" to return the parameters on all menus to the factory default settings. |
Note: Functions vary depending on model definition.
Information
| Information Display the | projector information for Model Name, Input Source, Signal Type, Display Mode, Serial No. and Software Version screen. |
Note: Functions vary depending on model definition.
Acer LAN webpage management
How to login in
Make sure you projector connects to your device through a LAN cable and set DHCP to off in Network. Open browser and enter the Server IP address by 192.168.100.10 to find below homepage of acer LAN webpage management. A password is needed to login in before using. Default password of User is "0000".
System Status
After login, main function pages will appear, i.e. System Status, Change Password, Projector Control, Network Setting, and Crestron.
System Status page is automatically selected after login.
Download EZCast Pro Installer for PC projection from Acer portal http://www.acer.com/projectors/app/
Change Password
Enduser can change the login password as wish.
Projector Control Panel
Enduser can control and adjust projector setting value via this page.
Network Setting
Enduser can set IP address as wish. After change network configurations, Network Setting on both webpage and projector will refresh automatically after press "Apply".
Crestron Setting (optional)
Enduser can change the settings for Crestron control system.
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center.
| # Problem Solution | |
| 1 Start-up problems | •If no lights turn on: •Be sure that the power cord is securely connected to the projector and the other end is plugged into an outlet with power. •Press the power button again. •Unplug the power cord and wait for a short while, then plug it in and press the power button again. |
| 2 Image problems | •If the searching source is displayed: •Press SOURCE to select an active input source. •Be sure the external source is turned on and connected. •For a computer connection, ensure your notebook computer's external video port is turned on. Refer to the computer manual. •If the image is out of focus: •While displaying the on-screen menu, adjust the focus ring. (The image size should not change; if it does, you are adjusting the zoom, not the focus.) •Check the projection lens to see if it needs cleaning. •If the image is flickering or unstable for a computer connection: •Press RESYNC. |
| 3 Remote control problems | •If the remote control does not operate: •Be sure nothing is blocking the remote control receiver on the front of the projector. •Use the remote control within the effective range. •Aim the remote control at the screen or at the front of the projector. •Move the remote control so it is more directly in front of or behind the projector and not as far to the side. |
LED & Alarm Definition Listing
LED Messages
| Message Power LED Temp LED Lamp LED | ||
| Stand-by mode Orange Off Off | ||
| Powering up Green flashing Off Off | ||
| Lamp retry Green flashing Off Orange flashing | ||
| Normal operation Green Off Off | ||
| Normal power-down cooling Orage flashing Off Off | ||
| Lamp error in normal operation Orage flashing Off Red | ||
| Lamp is not lit up Orage flashing Off Orage flashing | ||
| The remaining time of lamp life becomes 5% or lower. Green/Orange flashing Off Orange | ||
| Fan 1 (blower) error (the actual fan speed exceeds the desired speed) Red Red Off | ||
| Fan 2 (air outlet) error (the actual fan speed exceeds the desired speed) Red Orage flashing Off | ||
| Fan 3 (air inlet) error (the actual fan speed exceeds the desired speed) Red Green Off | ||
| Temperature error (over limited temperature) Green Red Off |
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp. Make sure the projector has been cooling down for at least 45 minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp.
To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 45 minutes to cool down.
Disconnect the power cord.
1 Remove the screw (a) and slide the lamp cover (b) for removal.
2 Disconnect the lamp connector (c).
3 Remove the screw (d) that secure the lamp module.
Pull out the lamp module (e) by the handle (f).
To replace the lamp module, use a new lamp and reverse the above steps.
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and secure the mount base.
2 Choose the length combination based on actual environment. (CM-01S doesn't include Type 2 and Type 3.)
Type 1 Type 2 Type 3
3 Type 1:
For the standard size use three bracket screws to mount the projector to the ceiling mount bracket.
Type 2 and Type 3:
Alternatively, for the larger size, use the sliding extensions for more supports.
Type 1: Type 2: Type 3:
Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution.
4 Connect the main body connector to the projector bracket (illustration 1), and then screw up four screws (illustration 2).
5 Adjust the angle and positioning as necessary.
natural_image
Technical line drawing of a mechanical clamp or bracket assembly with 360° angle annotation (no text or symbols on the diagram itself)
natural_image
Technical line drawing of a mechanical clamp or bracket assembly with no visible text or symbols
Note: The appropriate type of screw and washer for each model is listed in the table below. 4 mm diameter screws are enclosed in the screw pack.
| Screw Type B Washer Type | |||
| Diameter (mm) Length (mm) Large Small | |||
| 4 | 2 | 5 | V |
V
SCREW SPEC. M4 x 25 mm
Specifications
The specifications listed below are subject to change without notice. For final specs, please refer to Acer's published marketing specifications.
| Projection system | DLP® |
| Resolution | •P1160Bi/D701Ei/EV-S71Ki/X1125Pi/DX131Ei/BS-031K/P1160BTi/FSV1904 series: Native 800 x 600 SVGA resolution•P1260Bi/D711Ei/EV-X71Ki/X1225Pi/DX231Ei/BS-131K/P1260BTi/FNX1903 series: Native 1024 x 768 XGA resolution•P1360WBi/D721Ei/EV-W71Ki/X1325WPi/DX431Ei/BS-331K/P1360WBTi/FWX1902 series: Native 1280 x 800 WXGA resolution•P1560Bi/D751Ei/EV-F71Ki/X1525Pi/DX531Ei/BS-531K/P1560BTi/H6535Bi/H6535BTi/F1P1901 series: 1920x1080 1080p resolution |
| Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and VESA standards: SXGA, XGA, VGA, SVGA, SXGA+, WXGA, WXGA+, WSXGA + | |
| Video compatibility HDTV (720p, 1080i, 1080p), EDTV (480p, 576p), SDTV (480i, 576i) | |
| Aspect ratio Auto, 4:3, 16:9, 16:10 | |
| Displayable colors 1.07 billion colors | |
| Projection lens | •P1160Bi/D701Ei/EV-S71Ki/X1125Pi/DX131Ei/BS-031K/P1160BTi/FSV1904/P1260Bi/D711Ei/EV-X71Ki/X1225Pi/DX231Ei/BS-131K/P1260BTi/FNX1903/P1360WBi/D721Ei/EV-W71Ki/X1325WPi/DX431Ei/BS-331K/P1360WBTi/FWX1902 series: F = 2.42 ~ 2.62, f = 22~25.79 mm, 1.2X manual zoom and manual focus•P1560Bi/D751Ei/EV-F71Ki/X1525Pi/DX531Ei/BS-531K/P1560BTi/H6535Bi/H6535BTi/F1P1901 series: F = 2.47 ~ 2.66, f = 20.4 ~24.48 mm, 1.2X manual zoom and manual focus |
| Projection screen size (diagonal) 40" (102 cm) ~ 300" (762 cm) | |
| Projection distance | •P1160Bi/D701Ei/EV-S71Ki/X1125Pi/DX131Ei/BS-031K/P1160BTi/FSV1904/P1260Bi/D711Ei/EV-X71Ki/X1225Pi/DX231Ei/BS-131K/P1260BTi/ FNX1903 series: 3.3' (1.0 m) ~ 39.7' (12.1 m)•P1360WBi/D721Ei/EV-W71Ki/X1325WPi/DX431Ei/ BS-331K/P1360WBTi/FWX1902 series: 3.3' (1.0 m) ~ 33.5' (10.2 m)•P1560Bi/D751Ei/EV-F71Ki/X1525Pi/DX531Ei/BS-531K/P1560BTi/H6535Bi/H6535BTi/F1P1901 series: 3.3' (1.0 m) ~ 30.5' (9.3 m) |
| Throw ratio | •P1160Bi/D701Ei/EV-S71Ki/X1125Pi/DX131Ei/BS-031K/P1160BTi/FSV1904/P1260Bi/D711Ei/EV-X71Ki/X1225Pi/DX231Ei/BS-131K/P1260BTi/FNX1903 series: 50"@2 m (1.94 ~ 2.33) |
| •P1360WBi/D721Ei/EV-W71Ki/X1325WPi/DX431Ei/BS-331K/P1360WBTi/FWX1902 series: 60"@2 m (1.55 ~ 1.87) | |
| •P1560Bi/D751Ei/EV-F71Ki/X1525Pi/DX531Ei/BS-531K/P1560BTi/H6535Bi/H6535BTi/F1P1901 series: 66"@2 m (1.37 ~ 1.66) | |
| Horizontal scan rate 15 - 90 kHz | |
| Vertical refresh scan rate 24, 50 - 85 Hz | |
| Lamp type 210W user-replaceable lamp | |
| Keystone correction | ±30 degrees |
| Weight 2.6 Kg (5.74 lbs) | |
| Dimensions (W x D x H) 332 mm X 244 mm X 108 mm (13.1" x 9.6" x 4.3") | |
| Digital Zoom 1.8X | |
| Power supply AC input 100 - 240 V auto-switching power supply | |
| Power consumption Normal mode: 270W ± 10% @ 110VAC ECO mode: 230W ± 10% @ 110VAC EcoPro mode: 166W ± 10% @ 110VAC Standby mode < 0.5W Network standby mode: <3W | |
| Operating temperature 0°C to 40°C / 32°F to 104°F | |
| Standard package contents | •AC power cord x1 •Remote control x1 •Battery x2 (for remote control) •Quick start guide (Projector) x1 •Quick start guide (Media/Wireless function) x1 •WirelessProjection-Kit x1 (option) •CastMaster-Kit x1 (option) |
| I/O connectors | •Power socket •VGA IN 1 x 1 •VGA output x 1 •RS232 x 1 •3.5 mm audio jack output x 1 •3.5 mm audio jack input x 1 •Mini USB x1 (for firmware upgrade) •USB type A x1 (5V/1.5A power supply) •USB type A x1 (wireless dongle) •HDMI x 2 •RJ45 LAN input x 1 |
Note: Design and specifications are subject to change without notice.
Compatibility modes
A. Computer
•Multiple signal support
•Horizontal Frequency: 15-90 kHz, Vertical Frequency: 24, 50-85 Hz, Pixel Clock: 12-162 MHz
| Mode Resolution | Vertical frequency (Hz) | Horizontal frequency (kHz) | Analog Support | Digital Support | ||
| PC | VGA 640x480 | 60.0 31.47 | √ | √ | ||
| 72.0 67.86 | √ | √ | ||||
| 75.0 37.50 | √ | √ | ||||
| 85.0 43.27 | √ | |||||
| SVGA 800x600 | 60.0 37.88 | √ | √ | |||
| 72.0 48.08 | √ | √ | ||||
| 75.0 46.88 | √ | √ | ||||
| 85.0 56.67 | √ | |||||
| XGA 1024x768 | 60.0 48.36 | √ | √ | |||
| 70.0 56.48 | √ | √ | ||||
| 75.0 60.02 | √ | √ | ||||
| 85.0 68.67 | √ | |||||
| WXGA | 1280x720 60.0 44.80 | √ | √ | |||
| 1280x768 60.0 47.78 | √ | √ | ||||
| 1280x800 60.0 49.60 | √ | √ | ||||
| 1360x768 60.0 47.71 | √ | √ | ||||
| WXGA+ 1440x900 60.0 55.90 | √ | |||||
| SXGA | 1152x864 75.0 67.50 | √ | ||||
| 1280x1024 | 60.0 63.98 | √ | √ | |||
| 75.0 79.98 | √ | √ | ||||
| 1280x960 60.0 60.00 | √ | √ | ||||
| SXGA+ 1400x1050 60.0 65.32 | √ | √ | ||||
| WSXGA+ | 1680x1050 60.0 60.30 | √ | ||||
| 1920x1080 60.0 67.50 | √ | √ | ||||
| UXGA 1600x1200 60.0 75.00 | √ | |||||
B. DTV
| Mode Signal | Vertical frequency (Hz) | Horizontal frequency (kHz) | Analog Support | Digital Support | ||
| DTV Signal | 480P 72 | 0x480p 59.9 | 31.50 | √ | √ | |
| 576P 72 | 0x576p 50.0 | 31.60 | √ | √ | ||
| 720P 12 | 80x720p | 60.0 45.00 | √ | √ | ||
| 50.0 37.50 | √ | √ | ||||
| 1080P 19 | 20x1080p | 24.0 27.00 | √ | |||
| 60.0 67.50 | √ | √ | ||||
| 50.0 56.30 | √ | √ | ||||
Note 1: Functions vary depending on model definition.
Note 2: 480i/576i/1080i interlaced signals are not supported.
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Compliant with Russian regulatory certification
EAC
Radio device regulatory notice
Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio communication devices (RSS-247)
a Common information
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is intended to be operated indoors and installation outdoors is subject to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact the local office in the country of use. Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
And,
Acer Italy s.r.l.
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it
Product:
DLP
Projector
Trade Name: Acer
Model Number: F1P1901/ FWX1902/ FNX1903/ FSV1904
Marketing Name: P1560Bi/D751Ei/EV-F71Ki/X1525Pi/DX531Ei/
BS-531K/P1560BTi/H6535Bi/H6535BTi/ P1360WBi/D721Ei/
EV-W71Ki/X1325WPi/DX431Ei/BS-331K/P1360WBTi/ P1260Bi/
D711Ei/EV-X71Ki/X1225Pi/DX231Ei/BS-131K/P1260BTi/
P1160Bi/D701Ei/EV-S71Ki/X1125Pi/DX131Ei/BS-031K/P1160BTi
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislations: Directive 2014/53/EU on Radio Equipment, RoHS Directive 2011/65/EU and ErP Directive 2009/125/EC. The following harmonized standards and/or other relevant standards have been applied:
Electromagnetic compatibility
EN 55032:2015+AC:2016, Class B
EN 61000-3-2:2014 Class D
EN 55024:2010+A1:2015
EN 61000-3-3:2013
Radio frequency spectrum usage
EN 301 489-1 V2.1.1
This radio equipment operates with the following frequency bands and maximum radio-frequency power:
| Frequency bands | GSM | UMTS 5GHz | LTE | Bluetooth 2.4GHz | WLAN | ||
| 850/900 | 1800/1900 | ||||||
| Maximum radio-frequency power | 2W | 1W | 0.25W | 0.2W | <20dBm | <23dBm | <20dBm |
Year to begin affixing CE marking 2018.
RuJan
RU Jan / Sr. Manager
Acer Incorporated (Taipei, Taiwan)
Jan. 20, 2020
Date
Federal Communications Commission Declaration of Conformity
This equipment complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This equipment may not cause harmful interference, and
(2) This equipment must accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product: DLP Projector
Model Number: F1P1901/ FWX1902/ FNX1903/ FSV1904
Machine Type: P1560Bi/D751Ei/EV-F71Ki/X1525Pi/DX531Ei/
BS-531K/P1560BTi/H6535Bi/H6535BTi/
P1360WBi/D721Ei/EV-W71Ki/X1325WPi/
DX431Ei/BS-331K/P1360WBTi/
P1260Bi/D711Ei/EV-X71Ki/X1225Pi/DX231Ei/
BS-131K/P1260BTi/
P1160Bi/D701Ei/EV-S71Ki/X1125Pi/DX131Ei/
BS-031K/P1160BTi
Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U.S.A.
Contact Person: Acer Representative
Phone No.: 254-298-4000
Fax No.: 254-298-4147