LSGT100-4M - Air conditioner Baxi - Free user manual and instructions

Product Type	Split air conditioner
Indoor Unit Dimensions (W x H x D)	800 x 290 x 210 mm
Outdoor Unit Dimensions (W x H x D)	700 x 550 x 250 mm
Indoor Unit Weight	10 kg
Outdoor Unit Weight	30 kg
Power Supply	230 V ~ 50 Hz
Cooling Capacity	2.5 kW
Heating Capacity	2.8 kW
Power Consumption (Cooling)	0.8 kW
Refrigerant Type	R32
Airflow Rate (Indoor)	420 m³/h
Sound Level (Indoor)	25 - 40 dB(A)
Sound Level (Outdoor)	50 dB(A)
Filter	Washable air filter
Remote Control	Yes
Timer Function	Yes
Sleep Mode	Yes
Dehumidification Mode	Yes
Energy Class	A++ (estimated)
Maintenance	Clean air filter every 2 months
Safety Features	Overvoltage protection

Frequently Asked Questions - LSGT100-4M Baxi

How do I clean the air filter?

Turn off the unit and open the front panel. Remove the filter and vacuum or wash it with mild detergent. Let it dry completely before reinstalling. Clean every 2 months for optimal performance.

How do I use the remote control?

Point the remote at the indoor unit. Press MODE to select cooling, heating, fan, or dehumidification. Use +/- to adjust temperature. Press FAN to change fan speed. The remote also has timer and sleep buttons.

What should I do if the air conditioner is not cooling?

Check that the filter is clean and the unit is set to cooling mode with a temperature lower than room temperature. Ensure the outdoor unit is not obstructed. If problem persists, contact a qualified technician.

How do I set the timer?

Press the TIMER button on the remote. Use +/- to set the desired on/off time. Press TIMER again to confirm. The unit will automatically start/stop at the set time.

What refrigerant does this unit use?

This air conditioner uses R32 refrigerant, which is environmentally friendly with low global warming potential.

How do I switch between cooling and heating modes?

Press the MODE button on the remote repeatedly until you see the desired mode icon (snowflake for cool, sun for heat). The unit will start in that mode after a few seconds.

Does the outdoor unit need protection from rain?

The outdoor unit is designed to be weather-resistant and can be installed outdoors without additional shelter. Ensure it is placed on a stable surface with adequate airflow around it.

Can I install the air conditioner myself?

Installation should be performed by a qualified professional due to the need for electrical connections and refrigerant handling. Improper installation may void warranty and cause safety hazards.

What do I do if an error code appears on the display?

Refer to the user manual for error code explanations. Common codes indicate filter cleaning, communication errors, or sensor issues. Try resetting the unit by turning it off for 5 minutes. If the code persists, contact customer support.

How can I reduce energy consumption?

Set the thermostat to a comfortable but moderate temperature (24-26°C for cooling). Use sleep mode at night. Keep windows and doors closed. Clean the filter regularly to maintain efficiency.

USER MANUAL LSGT100-4M Baxi

Line drawing of a screwdriver inserting into a device with a grid panel (no text or symbols)

Diagram showing a screwdriver connecting to a wall-mounted electrical socket connected to a box (no text or symbols present)

graph TD
    A["Start: 23°C"] --> B["ON/OFF"]
    B --> C["Function: Fan, Swing, Mode"]
    C --> D["ON/OFF"]
    D --> E["Function: Fan, Swing, Mode"]
    E --> F["On/OFF"]
    F --> G["Function: Fan, Swing, Mode"]
    G --> H["On/OFF"]
    H --> I["Function: Fan, Swing, Mode"]
    I --> J["On/OFF"]
    J --> K["Function: Fan, Swing, Mode"]
    K --> L["On/OFF"]
    L --> M["Function: Fan, Swing, Mode"]
    M --> N["On/OFF"]
    N --> O["Function: Fan, Swing, Mode"]
    O --> P["On/OFF"]
    P --> Q["Function: Fan, Swing, Mode"]
    Q --> R["On/OFF"]
    R --> S["Function: Fan, Swing, Mode"]
    S --> T["On/OFF"]
    T --> U["Function: Fan, Swing, Mode"]
    U --> V["On/OFF"]
    V --> W["Function: Fan, Swing, Mode"]
    W --> X["On/OFF"]
    X --> Y["Function: Fan, Swing, Mode"]
    Y --> Z["On/OFF"]

Line drawing of a screwdriver inserting into a device (no text or symbols)

Diagram showing a screwdriver connecting to a wall-mounted electrical socket connected to a box (no text or symbols present)

Read and keep this manual.

PACKAGING CONTENT

DESCRIPTION	FIGURE	SPECIFICATIONS
Wired control TXW1AC		Dimensions(hight/wide/dedepth): 120mmx120mmx20mm Weight: 168 g
2 screws		M4x20
User and Installation manual
Long connection wiring		Length: 5000mm Weight: 99 g
Short connection wiring		Length: 50mm Weight: 10 g

BUTTONS DESCRIPTION

ON/OFF button

Press- "ON/OFF" button to start or shutdown the unit.

1. When the unit is running, users can regulate the operation mode, fan speed, setting temperature, special functions and other parameters on the wired controller.

graph LR
    A["Digital Display: 23 °C"] --> B["Timer Function"]
    B --> C["Fan Switch"]
    C --> D["Bright Swing"]
    D --> E["Mode Comfort"]
    E --> F["* 23 °C"]

1. When the unit is standby, the wire controller displays indoor ambient temperature (Room temp.), the other content are not displayed.

button-Temperature, time setting, function selection

1. When the unit is running, press "▲" or "▼" button to increase or decrease the setting temperature by 1^ C.

graph TD
    A["1st Temp: 23 °C"] --> B["Timer Fan: ON/OFF Swing Mode: Function Comfort"]
    B --> C["24 °C"]
    C --> D["Timer Fan: ON/OFF Swing Mode: Function Comfort"]

Under COOL, DRY, and HEAT modes, the setting temperature range is 16^ C-32 ^ C;

The controller will display" Set temp." to show the selling temperature;

1. Under the function selection mode, press "▲" or "▼" button to select function;
2. Under the timing mode, press "▲" or "▼" button to setting time.

Mode setting

When the unit is running, press "MODE" button, the running mode will switch according to the following order:

graph LR
    A["AUTO"] --> B["COOL"]
    B --> C["DRY"]
    C --> D["FAN"]
    D --> E["HEAT"]
    E --> F["AUTO"]

The initial setting temperature for each mode is 24^ C, and there is no temperature setting and automatic wind under FAN mode.

The setting of "Wind speed"

When the unit is running, press "Fan" button to switch fan speed in the following order:

3-gear of fan speed:

4-gear of fan speed:

graph LR
    A["Auto"] --> B["(Low)"]
    B --> C["(Medium)"]
    C --> D["(High)"]
    D --> E["(Super-high)"]
    E --> F["Auto"]

In turbo mode, display fan speed (turbo+ highest fan speed icon).

The setting of "Swing"

1. For the unit only has the function of up and down swing: When the unit is running, press "Swing" button to enter or cancel up and down swing. At the time of opening up and down swing “☐” is lighting. At the time of closed, swing icon will disappear. If the unit has positioning swing function, press "Swing" button to regulate the swing angle in the order:

graph LR
    A["一"] --> B["八"]
    B --> C["八"]
    C --> D["i"]
    D --> E["i"]
    E --> F["彡"]

1. For the unit only has the function of left and right swing: when the unit is running, press "Swing" button lo enter or cancel left and right swing. At the time of opening left and right swing," [icon] is lighting. At the time of closed, swing icon will disappear. If the unit has positioning swing function, press "Swing" button lo regulate the swing angle in the order.

2. For the unit has the functions of left and right swing and up and down swing: Press "Swing" button, the swing mode will switch in the following cycle order:

graph LR
    A["✓"] --> B["✓"]
    B --> C["✓"]
    C --> D["✓"]
    D --> E["✓"]
    E --> F["✓"]

The setting of "Comfort"

1. When the unit is running, press "Comfort" button to enter comfort function. The default setting temperature of COOL and DRY mode is 26 °C, HEAT mode 24 °C, setting temperature is adjustable. Fan speed is automatic and adjustable. The comfort function will be cancelled if the running mode is changed.

2. Press "Comfort button again to cancel comfort function."

"Timing" function

Users can set shutdown timing time when the unit is running, and set starting up timing time when the unit is stand by.

1. Press "Timer" button when the unit is running, the wired controller will display "Time off" and users can set the shutdown timing time; when the unit is standby, the wired controller will display ", and users can set the starting-up timing time.

graph LR
    A["23 °C Display"] --> B["CN/OFF Function"]
    B --> C["OSH 23 °C Display"]

1. After entering timing time setting interface, the default timing time is 0.5h, at this moment, press "▲" or "▼" button to regulate the timing time. If the button is not pressed for 10 seconds, the timing setting will be cancelled, and then return to the state of non-timing.

graph LR
    A["0SH 23 °C"] --> B["ON/OFF"]
    B --> C["Timer Fan Swing Mode"]
    C --> D["Function Comfort"]
    D --> E["ON/OFF"]

1. After the setting of timing, press "Timer" button again to confirm. The timing setting is successful and the time bar will stop blinking.

graph LR
    A["ON/OFF ON/OFF 23 °C"] --> B["Timer: F=0, Swing: Off"]
    B --> C["Function: ✓"]
    C --> D["Comfort"]
    D --> E["ON/OFF ON/OFF 23 °C"]

1. After the setting "Timer On" function, you can adjust the fan speed, running mode, set temperature, and swing angle. If there is no operation for 10 seconds, standby screen will be displayed.

graph TD
    A["Start: 23°C"] --> B["Timer Fan ON/OFF"]
    B --> C["Function"]
    C --> D["ON/OFF Mode"]
    D --> E["Timer Fan ON/OFF"]
    E --> F["Function"]
    F --> G["ON/OFF Mode"]
    G --> H["End"]

1. Timing range: 0.5-24 hours. Press "▲" or "▼" button once, the timing time will increase or decrease by 0.5 hours. When the timing time is more than 10 hours, press "" or "" button once, the timing time will increase or decrease by 1 hour.

2. Press "Timer" button or "ON/OFF" button to exit TimerON or TimerOFF.

OPTIONAL FUNCTIONS

The wired controller is for the general-purpose, specific functions of the controller are subject to the functions of your air conditioning unit. Note: In the interface of function setting, press any button such as Timer, Fan, Swing, Mode, ON/OFF, and Comfort to exit the interface and conventional operation interface will display. If there is no operation for 10S, you can exit the interface.

Enter function: Press function button to enter function selection interface, press "

▲ " or "▼" to select a function, and the corresponding icon will flash, press "function" button again to confirm the function.

Cancel function: Press function button lo enter function selection interface, press "

▲ " or "▼" lo select function and !he corresponding icon will flash, press "function" button again to cancel the function.

The setting of "Turbo" function

Turbo function: The fan speed will be ultra-high in turbo mode and users can achieve rapid cooling or heating effect.

Open turbo function:

1. When the unit is running in cooling or healing mode, press "Function" key to enter the interface of function selection.

2. Press "▲" or "▼" button to switch to turbo function, at this moment, " " icon is flashing.

1. Press "Function" button to confirm turbo function, at this moment, icon " ", fan speed display is (Turbo and speed speed icons).

graph TD
    A["Timer"] --> B["ON/OFF"]
    B --> C["Status: 23 °C"]
    C --> D["Function"]
    D --> E["ON/OFF"]
    E --> F["Status: 23 °C"]
    F --> G["Function"]
    G --> H["ON/OFF"]
    H --> I["Status: 23 °C"]

Cancel turbo function:

1. When turbo function is opened, press "Function" button to enter the interface of function selection.
2. Press "▲" or "▼" switch to strong function, at this moment, icon "💡" is flashing, press "Function" button to cancel strong function, and strong icon would not display.

graph TD
    A["Timer"] --> B["Fan ON/OFF"]
    B --> C["Swing Mode"]
    C --> D["Function ↑"]
    D --> E["Comfort ↓"]

    F["Sleep"] --> G["23 °C"]
    G --> H["Reset Temp"]

    I["Timer"] --> J["Fan ON/OFF"]
    J --> K["Swing Mode"]
    K --> L["Function ↑"]
    L --> M["Comfort ↓"]

Note: The unit without turbo function can also set turbo function on the wired controller, the performance is high fan speed, but “ ” icon and “ Turbo ” icon do will not display.

The setting of "Sleep" function

Sleep function: Make indoor unit will run according to pre-set sleep temperature curve, which creates a comfortable sleep environment and improves sleep quality.

Enter sleep function:

1. In the stale of running, press "Function" button to enter the interface of function selection.

2. Press "▲" or "▼" button to switch to sleep function, "Sleep" icon is flashing at this moment.

3. Press" Function" button to open sleep function, at this moment, icon "Sleep" is lighting.

graph TD
    A["Timer"] --> B["Fan"]
    B --> C["ON/OFF"]
    C --> D["Swing"]
    D --> E["Comfort"]
    F["Function"] --> G["Switch"]
    G --> H["Comfort"]
    I["Set Temp"] --> J["23 °C"]
    J --> K["Sleep"]
    K --> L["ON/OFF"]
    L --> M["Function"]
    N["Reset"] --> O["Set Temp"]
    P["Reset"] --> Q["23 °C"]
    R["Reset"] --> S["23 °C"]
    T["Reset"] --> U["23 °C"]
    V["Reset"] --> W["23 °C"]
    X["Reset"] --> Y["23 °C"]

Cancel "sleep" function:

1. When sleep function is opened, press "Function" button to enter the interface of function selection.
2. Press "▲" or "▼" button to switch to sleep function, icon Sleep is flashing.
3. Press "Function" button again to cancel sleep function.

graph TD
    A["Timer"] --> B["Fan"]
    B --> C["ON/OFF"]
    C --> D["Swing"]
    D --> E["Comfort"]
    F["Function"] --> G["Switch"]
    G --> H["Comfort"]
    I["Set Temp 23 °C"] --> J["Sleep 23 °C"]
    J --> K["OK"]
    L["ON/OFF"] --> M["Action"]
    M --> N["Comfort"]

The setting of "ECO" function

Enter ECO function:

1. Press "Function" button to enter the interface of function selection.

2. Press “▲” or “▼” button lo switch lo ECO function, at this moment, “Eco” icon is flashing.

3. Press "Function" button again to confirm ECO function, at this moment, "ECO" icon is flashing.

graph TD
    A["Timer"] --> B["Fan"]
    B --> C["Swing"]
    C --> D["Mode"]
    D --> E["Function"]
    E --> F["ON/OFF"]
    F --> G["23 °C"]
    G --> H["Sleep"]
    H --> I["23 °C"]
    I --> J["Function"]
    J --> K["ON/OFF"]
    K --> L["Comfort"]
    L --> M["23 °C"]
    M --> N["SET/ON"]
    N --> O["23 °C"]
    O --> P["23 °C"]

Cancel ECO function:

1. Press "Function" button to enter the interface of function selection.
2. Press "▲" or "▼" button to switch to ECO function, at this moment Icon is flashing.
3. Press "Function" button again to cancel ECO function.

graph TD
    A["Timer"] --> B["Fan"]
    B --> C["ON/OFF"]
    C --> D["Swing"]
    D --> E["Comfort"]
    F["Function"] --> G["Switch"]
    G --> H["Comfort"]
    I["Set Temp"] --> J["23°C"]
    K["Sleep"] --> L["23°C"]
    M["ON/OFF"] --> N["Comfort"]
    O["Set Temp"] --> P["23°C"]
    Q["Action"] --> R["Action"]

The setting of "Mildew-proof" function

Mildew-proof function: After shutdown, the air conditioner would automatically dry the moisture in the evaporator of indoor unit, so as to avoid mildewing.

Enter mildew-proof function:

1. Under COOL and DRY mode, press "Function" button lo enter the interface of function selection.
2. Press "▲" or "▼" button to switch to the mildew-proof function setting interface, at this moment, icon "●" is flashing.
3. Press "Function" button again to enter mildew-proof function, icon "OK" is lighting.

graph TD
    A["Timer Fan Swing Mode"] --> B["23 °C"]
    C["Function Comfort"] --> B
    D["Timer Fan Swing Mode"] --> E["23 °C"]
    F["Function Comfort"] --> E
    G["Sleep 23 °C"] --> H["23 °C"]

Cancel fungus-proof function:

1. When mildew proof function is ON, press "Function" button to enter the interface of function selection.
2. Press "▲" or "▼" button to mildew proof function, icon "×" is flashing.
3. Press "Function" button again to cancel mildew proof function, icon will " disappear.

graph TD
    A["Timer"] --> B["Fan"]
    B --> C["ON/OFF"]
    C --> D["Swing"]
    D --> E["Comfort"]
    F["Function"] --> G["Switch"]
    G --> H["Comfort"]
    I["Sleep"] --> J["23 °C"]
    K["Set Temp"] --> L["23 °C"]
    M["ON/OFF"] --> N["Function"]
    O["SET Temp"] --> P["23 °C"]
    Q["Timer"] --> R["Fan"]
    R --> S["SWing"]
    S --> T["Mode"]
    U["Function"] --> V["Switch"]
    V --> W["Comfort"]

The setting of "Light Sensation" function

Light sensation function: Detect the On and Off of indoor lamplight and switch to low fan speed when the lamplight is off, which can reduce the noise and create a comfortable sleep environment for users.

Enter light sensation function:

1. In the state of running, press "Function" button to enter the interface of function selection.
2. Press "▲" or "▼" to switch to light sensation function, icon "☐" is flashing.
3. Press Function button again to enter light sensation function, at this moment, icon" " is lighting.
4. When light sensation function is on, if the indoor lamplight is OFF and lasts for 20 minutes, the unit will automatically enter sleep mode. If the indoor lamplight is ON, and lasts for 20 minutes, the unit will cancel sleep mode and run according to the setting fan speed.

graph TD
    A["Timer"] --> B["Fan ON/OFF"]
    B --> C["Sweep Mode"]
    C --> D["Function ↑"]
    D --> E["Comfort ↓"]

    F["* 23 °C"] --> G["Sleep"]
    G --> H["OK"]
    H --> I["Function ↑"]
    I --> J["Sweep Mode"]
    J --> K["Comfort ↓"]

    L["* 23 °C"] --> M["Stop"]
    M --> N["ON/OFF"]
    N --> O["Function ↑"]
    O --> P["Sweep Mode"]
    P --> Q["Comfort ↓"]

    R["Timer"] --> S["Fan ON/OFF"]
    S --> T["Sweep Mode"]
    T --> U["Function ↑"]
    U --> V["Sweep Mode"]
    V --> W["Comfort ↓"]

    X["* 23 °C"] --> Y["Stop"]
    Y --> Z["Sweep Mode"]
    Z --> AA["Function ↑"]
    AA --> AB["Sweep Mode"]
    AB --> AC["Comfort ↓"]

Cancel light sensation:

1. When light sensation function is on, press "Function" button to enter the interface of function selection.
2. Press "▲" or "▼" button to switch to light sensation function, icon is flashing.
3. Press "Function" button again to cancel light sensation function, icon "→" will disappear.

graph TD
    A["Timer"] --> B["Fan ON/OFF"]
    B --> C["Swing"]
    C --> D["Comfort"]
    E["Function"] --> F["Set Temp. 23 °C"]
    F --> G["ON/OFF"]
    H["Sleep"] --> I["Set Temp. 23 °C"]
    I --> J["Swing"]
    J --> K["Comfort"]
    L["Timer"] --> M["Fan"]
    M --> N["Swing"]
    N --> O["Mode"]
    P["Function"] --> Q["Set Temp. 23 °C"]
    Q --> R["SWing"]
    R --> S["Comfort"]

The setting of "Clean" function

Clean function: The air conditioner can clean the evaporator automatically, which can not only keep air fresh, but also reduce the recession of cooling effect.

Enter clean function:

1. In the state of standby, press "Function" button to enter the interface of function selection, icon " " is flashing.
2. Press "Function" button again to confirm clean function, at this moment, icon "Clean" is lighting.
3. When the unit is performing clean function, the wired controller will keep displaying icon "", until it is finished.

graph TD
    A["Sensor Input: 23 °C"] --> B["Timer Fan Swing Mode"]
    B --> C["Function ↑ ✓ Comfort"]
    C --> D["ON/OFF: 23 °C"]
    D --> E["Timer Fan Swing Mode"]
    E --> F["Function ↑ ✓ Comfort"]

DISPLAY PROMPT FUNCTIONS

"WIFI" function display

If the unit is equipped with a WIFI function module, the icon " 🔊" is lighting on wired controller.

If the unit is not equipped with a WIFI function module, the icon " 🔊" does not display.

"Shielding" function display

When unit is locked by centralized control, the wired controller will display "☐".

"Mute" function display

When the unit enter silent function, display " 🔍" icon, when silent function is cancelled, the icon does not display.

Note: The unit without silent function can also set silent through wired controller, but it shows in the way of low wind grade, but " 🔍" does not display.

"Oil Return / Defrost" function display

When the unit is running in the state of Oil Return or Defrost, " " icon is lighting on wire controller.

When the unit has finished Oil Return or Defrost process," 🔊" icon does not display.

"Filter Screen Clean" function display

Filter screen cleaning reminder function: The unit can record its running time, when reaching the time set by the user, it will remind the user to clean the filter screen, so as to avoid prolonged cleaning and filter screen blockage, which can result in poor heating/cooling effect, abnormal protection, bacterial breeding, and other problems. When the running time reaches the filter screen cleaning reminder time set by a user, the unit will give out a reminder of filter screen cleaning, wired controller displays " ” Icon, reminding the user to clean filter screen. At this moment, long press "Timer" button for 5S to cancel the reminder, then the icon does not display. A filter screen cleaning reset signal is sent to the unit.

Celsius and Fahrenheit switching display

When users set Celsius to be valid, the wired controller will display Celsius temperature. When users set Fahrenheit to be valid, the wired controller will display corresponding Fahrenheit temperature synchronously.

"Child Lock" function display

Press both " " or " " buttons for more than 5S to enter locking, the controller

will display “☐”. In the state of locking, operations on the wired controller are disabled (but remote control receiving is valid). The method of unlocking: Press both " " or " " buttons for more than 5S or power off the unit to release the locking

(" does not display).

Remote control function

The wired controller can receive remote control commands and update the current status.

Start-up the unit with remote controller, wired controller work in accordance with the state set on the remote controller and displays corresponding working mode.

Room temperature sensor equipped on the wired controller

When the wire controller is equipped with a room temperature sensor and the sensor is not damaged, it is default that the ambient temperature detected by the sensor on the controller and the temperature value will be sent to the main PCB of the unit.

If the wire controller is not equipped with a room temperature sensor or the sensor is damaged, the room temperature will be detected by the temperature sensor of the unit itself.

Fault display

When the unit has fault, the time bar will directly display the fault code and flash, the display mode is Ex: MM (MM is the fault code, please read the corresponding product manual).

Use a flathead screw driver to pry the bottom groove of the wire controller lightly (too much force would damage circuit board), pry rotationally to open the back cover.

Line drawing of a screwdriver inserting into a device (no text or symbols)

As shown in Fig.3, fix 4 * 20mm screws provided together with the back cover on 8 6 box, then pass lead wires through the back cover.

Simple line drawing of a wall socket connected to a box, with a screwdriver inserted (no text or symbols)

After connecting the connecting wire to the main body of the wire controller, install main body part according to the following steps:

1). Push the upper part of main body into the clip.
2). Use the force of inclined top to install the lower part of main body (horizontal installation is prohibited, which is easy to damage the structural slot).

Connect the long cable to the wired control cable	Connect the other side of the long cable with short one	Connect the other side of the short cable (white connector) to the PCB

R32 MONO FLOOR/CEILING AND MONO CASSETTE INDOOR UNITS → RZGN(C/K)(35/50/70/100/120/140/160)

1. In case of duct units, wired control is supplied as standard.
2. Connect the white control connector to the "CN7" connector of the indoor unit PCB as shown in the following schema:

graph TD
    subgraph Power
        A["AC_N"] --> B["XE"]
        C["AC_L"] --> D["L_R"]
        E["RD"] --> F["BU"]
        G["L"] --> H["N"]
        I["N"] --> J["A"]
        K["A"] --> L["B"]
        M["B"] --> N["Communication"]
    end

    subgraph Communication
        O["Step motor M2"] --> P["Pump M3"]
        Q["Step motor M4"] --> R["UP_DW"]
        S["Step motor M7"] --> T["Control PCB"]
        U["Step motor M9"] --> V["Control PCB"]
        W["Step motor M10"] --> X["Control PCB"]
        Y["Step motor M11"] --> Z["Control PCB"]
        AA["Step motor M12"] --> AB["Control PCB"]
        AC["Step motor M13"] --> AD["Control PCB"]
        AE["Step motor M14"] --> AF["Control PCB"]
        AG["Step motor M15"] --> AH["Control PCB"]
        AI["Step motor M16"] --> AJ["Control PCB"]

    subgraph Power_Temp
        AK["CN1"] --> AL["CN3"]
        AM["CN4"] --> AN["CN7"]
        AO["CN8"] --> AP["CN17"]
        AQ["CN9"] --> AR["CN12"]
        AS["CN10"] --> AT["CN6"]
        AU["CN11"] --> AV["CN13"]
        AW["CN12"] --> AX["CN14"]
        AY["CN13"] --> AZ["CN15"]
        BA["CN14"] --> BB["CN16"]
    end

    subgraph Communication_Pump
        BC["Pump CN3"] --> BD["Pump CN9"]
        BE["Pump CN7"] --> BF["Pump CN16"]
    end

    subgraph Power_Pump
        BG["Pump CN1"] --> BH["Pump CN6"]
        BI["Pump CN3"] --> BJ["Pump CN10"]
    end

    subgraph Communication_Pump
        BK["Pump CN3"] --> BL["Pump CN10"]
        BM["Pump CN1"] --> BN["Pump CN6"]
    end

    subgraph Power_Temp
        BO["Pump CN1"] --> BP["Pump CN6"]
        BQ["Pump CN3"] --> BR["Pump CN10"]
    end

    subgraph Communication_Pump
        BS["Pump CN3"] --> BT["Pump CN10"]
    end

    subgraph Power_Pump
        BU["Pump CN3"] --> BV["Pump CN10"]
    end

    subgraph Communication_Pump
        BW["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Power_Temp
        BY["Pump CN3"] --> BZ["Pump CN10"]
    end

    subgraph Communication_Pump
        BQ["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Power_Pump
        BW["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"] --> BZ["Pump CN10"]
    end

    subgraph Power_Temp
        BZ["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Power_Pump
        BZ["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Power_Temp
        BZ["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Power_Pump
        BZ["Pump CN3"] --> BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"]
        BX["Pump CN10"]
    end

    subgraph Power_Temp
        BZ["Pump CN3"]
        BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"]
        BX["Pump CN10"]
    end

    subgraph Power_Pump
        BZ["Pump CN3"]
        BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"]
        BX["Pump CN10"]
    end

    subgraph Power_Temp
        BZ["Pump CN3"]
        BX["Pump CN10"]
    end

    subgraph Communication_Pump
        BX["Pump CN3"]
        BX["Pump CN10"]
    end

    subgraph Power_Pump
        BZ["Pump CN 3"]
        BX["Pump CN 2"]
    end

    subgraph Communication_Pump
        BX["Pump CN 3"]
        BX["Pump CN 2"]
    end

R32 MULTI CASSETTE INDOOR UNITS → LSGNK (25/35/50)-XM

1. In case of duct units, wired control is supplied as standard.
2. Connect the white control connector to the "CN8" connector of the indoor unit PCB as shown in the following schema:

graph TD
    A["Power"] --> B["Communication"]
    B --> C["AC_L3"]
    C --> D["Transformer"]
    D --> E["AC_N"]
    D --> F["CN4"]
    D --> G["CN1"]
    D --> H["CN13"]
    H --> I["Panel receiver"]
    I --> J["CN8"]
    I --> K["Wired control"]
    K --> L["CN11"]
    K --> M["CN9"]
    K --> N["CN7"]
    K --> O["Evap Temp"]
    P["Drain pump"] --> Q["M2"]
    R["Fan motor"] --> S["M1"]
    T["Step motor"] --> U["M3"]
    V["Float switch"] --> W["CN12"]
    X["Room Temp"] --> Y["Tao"]
    Z["Timer"] --> AA["Fan"]
    AB["Fan OFF"] --> AC["Swing"]
    AD["Mode"] --> AE["Comfort"]

ON/OFF-Taste

Line drawing of a screwdriver inserting into a device component (no text or symbols)

Diagram showing a tool interacting with a wall-mounted socket connected to a box (no text or symbols present)

Line drawing of a screwdriver inserting into a device component (no text or symbols)

Diagram showing a screwdriver connecting to a wall-mounted switch and connected to a box (no text or symbols present)