IAN 274849 - Faucet MIOMARE - Free user manual and instructions

Product Type	Single-handle kitchen faucet
Model Number	IAN 274849
Brand	MIOMARE
Material	Chrome-plated brass
Overall Height	15.5 cm
Spout Reach	20.0 cm
Spout Height	13.0 cm
Fitting Connection	1/2" male thread, hot and cold water
Handle Type	Single lever
Cartridge Type	Ceramic disc
Flow Rate	5.7 L/min at 3 bar
Maximum Pressure	6 bar (test pressure 10 bar)
Maximum Water Temperature	60°C (short-term 80°C)
Aerator	Integrated, swivel
Rotation Angle	360°
Mounting Type	Single-hole deck mount
Included Accessories	Mounting kit, hot/cold hoses, wrench
Weight	1.2 kg
Certifications	DVGW, WRAS compliant
Spare Parts Availability	Via IAN number on manufacturer website
Care Instructions	Clean with damp cloth; avoid abrasive cleaners
Warranty	2 years (according to national law)

Frequently Asked Questions - IAN 274849 MIOMARE

How do I install this faucet?

Installation is straightforward for a single-hole setup. Connect the hot and cold water hoses to the corresponding valves, feed the hoses through the sink hole, secure the faucet with the provided mounting nut, and connect the hoses. Tighten all connections by hand and then with a wrench. Open the water supply slowly and check for leaks.

What is the flow rate of this faucet?

The flow rate is approximately 5.7 liters per minute at a pressure of 3 bar. It may vary depending on your water pressure.

Can I use this faucet with an instant water heater?

Yes, the faucet is compatible with most instantaneous water heaters as long as the connection size matches (1/2 inch). Ensure the water temperature does not exceed 60°C for continuous use.

How do I clean and maintain this faucet?

Clean the faucet with a soft, damp cloth. Avoid abrasive cleaners, scouring pads, or harsh chemicals as they may damage the chrome finish. For limescale, use a mild vinegar solution and rinse thoroughly.

What should I do if the faucet leaks?

First, check if the hoses are properly tightened. If leaking from the handle, the ceramic cartridge may need replacement. You can order a spare cartridge via the IAN 274849 number. For persistent leaks, contact a professional plumber.

Is this faucet suitable for low water pressure?

The faucet works well with standard household water pressure. For very low pressure (below 0.5 bar), the flow may be reduced. Consider installing a pressure booster if needed.

How do I replace the aerator?

Unscrew the aerator from the spout tip counterclockwise. Clean or replace it with a new one of the same size (standard M24 thread). Reattach by hand-tightening clockwise.

What is the warranty period?

This faucet comes with a 2-year warranty covering manufacturing defects. Normal wear and tear, limescale damage, or improper installation are not covered. Keep your purchase receipt.

Are spare parts available?

Yes, spare parts such as cartridges, aerators, and hoses are available. Use the IAN 274849 model number to search for compatible parts on the MIOMARE website or contact customer support.

Can I use this faucet outdoors?

This faucet is designed for indoor kitchen use. Outdoor exposure may cause corrosion or damage to the chrome finish. For outdoor use, consider a frost-proof model.

USER MANUAL IAN 274849 MIOMARE

Assembly, operating and safety instructions

DE AT CH

WANNENFÜLL-/BRAUSE-ARMATUR

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

DE AT CH

GB / IE Assembly, operating and safety instructions Page 5

Exploded view diagram of a hairdryer with numbered parts for identification

Table of contents

Introduction

Intended use....Page 6

Parts description Page 6

Technical Data Page 6

Scope of delivery....Page 6

Safety notices Page 7

Installation

Connecting the fitting....Page 7

Connecting accessories (shower hose and shower head)......Page 7

Operation

Start-up......Page 8

Maintenance and Cleaning

Maintaining and cleaning the tap Page 8

Replacing the cartridge Page 8

Disposal Page 9

Information

Potability of tap water....Page 9

Warranty and Service......Page 9

Introduction

List of pictograms used
	Read the instructions!	WARNING!	Potential of serious to fatal injuries.
	Observe the warning and safety instructions!		Beware of electric shock!
	Risk of fatal injury and accidents for infants and small children!		Dispose of packaging and device in an environmentally-friendly way!

Bath & Shower Mixer Tap

- Introduction

Congratulations on the purchase of your new product. You have selected a high quality product. The assembly and operating instructions are part of this product. Please carefully read these assembly instructions / instructions for use before use and observe all instructions. These instructions contain important information about installation, settings and care. Please retain these installation instructions / instructions for use and hand them on to any future owner.

Intendeduse

The product is only designed to regulate the hot and cold water flow. For tub installation only. Suitable for use with all pressure-resistant hot water systems such as central heating, continuous-flow water heater, pressure boiler etc. This product is not suitable for low pressure water heaters or pressure-free small storage reservoirs, e.g. wood- or coal-burning domestic hot water heaters, oil or gas-fired hot water heaters, or open electrically heated cylinders. When in doubt please consult a plumber or heating specialist. Any use not specified or product modification is prohibited and will result in damage. Any form of use other than the stipulated intended purpose can cause danger to life and cause injury. The product is for private use only and is not intended for medical or commercial use. The manufacturer accepts no responsibility if the intended purpose of this unit is not adhered to.

- Parts description

1 Handle*
2 Locking screw*
3 Hot/cold plaque*
4 Cartridge cover ring*
5 Cartridge lock nut*
6 Cartridge*
7 Diverter*
8 Fitting body
9 Aerator*
10 Shower connection*
11 2 Swivel nuts*
12 2 Seals
13 2 Covers
14 2 S-connectors
15 Allen key

* preinstalled

- Technical Data

Swivel nut (water connections): G 3/4"

Shower hose connection: G 12

- Scope of delivery

1 Bath filling- / shower valve 1 - 11
2 Caps 13
2 S-connectors with silencer 14
2 Seals 12
1 Allen key
1 Instructions for assembly / operation

6 GB/IE

miomare

Safety notices

DANGWARNING!

LIFE AND RISK OF ACCIDENTS FOR INFANTS AND CHILDREN!

Never leave children unattended with the packaging material. Suffocation hazard. Keep this product well away from children. This product is not a toy.

BEWARE OF ELECTRIC SHOCK!

Leaking or water discharge can lead to life-threatening danger due to

electric shock. Carefully check that all connections are watertight. Also ensure that all wires of electric appliances are correct and have been securely installed.

CAUTION! RISK OF INJURY! Please ensure

that no parts are damaged and that all parts are correctly assembled. Incorrect assembly could lead to injury. Please note that the seals are wear parts and must be changed from time to time. Damaged parts could impact safety and function.

Be sure all seals are correctly seated.

SCALDINGRISK! When adjusting the hot water temperature be sure the water temperature is not too high.

CAUTION! Ensure that the hot / cold water plaque 3 has been attached the right way round. The correct position is as follows: left = red (hot water) right= blue (cold water).

CAUTION! DAMAGE TO THE ARTICLE!

Please have all installations performed by skilled individuals.

Please note that the seals are wear parts and must be changed from time to time.

Any leakage or sudden escape of water can cause considerable damage to buildings and property. All connections must therefore be checked carefully to ensure that they are tight.

Familiarise yourself prior to installation with all local conditions, e.g. water connections and shut-off device.

The product is only suitable for use in rooms in which a temperature above 0 °C is maintained.

●Installation

Note: Familiarise yourself with the product prior to assembly. Carefully read the following assembly instructions and safety advice. In the event of incorrect installation, all warranty claims – particularly in relation to subsequent damage – are excluded.

CAUTION! Before you start installation turn off the water supply at the mains. Otherwise injuries and / or property damage may occur.

Connecting the fitting

Note: this step requires an SW 30 mm open-end spanner and sealing tape.

Note: cover any parts which will be screwed with a damp cloth or plastic clamps. This will prevent scratches.

Follow these steps:

Wrap sealing tape around the roughened threaded part ( 12 " thread) of the S-connectors 14.
Note: sealing tape not included.
☐ Screw the S-connectors 14 with the sealed threaded parts into the wall connectors.
☐ Horizontally align the screwed in S-connectors 14 with the spacing guide for the fitting.
By hand, tightly screw the caps 13 onto the S - connectors 14 to the wall.
☐ Insert the seals 12 into the swivel nuts 11 and screw the fitting body 8 with the swivel nuts 11 onto the S-connectors 14.

●Connecting accessories (shower hose and shower head)

Note: Shower hose and shower head are not included in delivery.

Note: Cover any parts which will be screwed with a damp cloth or plastic clamps. This will prevent scratches.

☐ Connect a standard shower hose to the shower connector 10.
- Connect a standard shower head to the shower hose.

Installation / Operation / Maintenance and Cleaning

Note: Also refer to the assembly instructions for the accessories.

Operation

- Start-up

After the initial commissioning, carefully check all connections for leaks.

☐ Check the operation of the fitting. To do so, swing the handle 1 into all permissible positions.

Note: If the tap has not been used for a long period, flush the pipes thoroughly to avoid stagnation and build-up of residue.

- Open the main water supply. - Lift the handle 1 and swing it up and down in order to regulate the speed or temperature of the water.

Hot water:

Swing the handle 1 to the left.

Cold water:

Swing the handle 1 to the right.

Note: When the mixer tap is open, pull the diverter button 7 upward in order to switch to the shower function

Depress the diverter button 7 in order to end the shower function.

Note: Upon closing the mixer tap the shower function is automatically ended.

● Maintenance and Cleaning

● Maintaining and cleaning the tap

Please note that sanitary taps require special care and attention. Therefore, please follow the instructions:

- Never clean with petrol, solvents or harsh cleaners or hard cleaning brushes, etc. These can damage the product surface. - Dry your fitting with a cloth after every use to prevent any lime deposits.

☐ Clean the shower valve with a damp, soft cloth and, if necessary, mild detergent.

Non-observance of the above care advice can be expected to result in damage to the surfaces of the product. This will inevitably invalidate the guarantee.

- Replacing the cartridge

A cartridge 6 is a wear part that needs replacing according to the hardness and / or degree of contamination of the water. This becomes evident when the handle 1 becomes difficult to move.

A new cartridges 6 can be obtained from the listed service office.

Note: This step requires an open-end spanner SW 27 mm or fitting pliers.

Proceed as follows to replace the cartridge 6:

☐ Shut off the main water supply. Allow any remaining water in the pipework to drain.

☐ Remove the hot / cold plaque 3 by adjusting the handle to the highest position between the rim and the hot / cold plaque 3 and the outside of the handle 1.

Note: Use light pressure to carefully push the hot/cold plaque 3 outward so as not to scratch the surface.

☐ Loosen the locking screw 2 with an Allen key, turning it counter-clockwise.

CAUTION! Do not completely unscrew the locking screw 2. Only loosen this as far as is necessary to remove the handle 1.

□ Remove the handle 1.

☐ Unscrew the cartridge covering ring 4, do not use pliers or a spanner. Otherwise the product could be damaged.

☐ Loosen the cartridge locknut 5 below with the fitting pliers or an open-ended spanner SW 27 mm and remove the entire cartridge 6 from the fitting body 8.

Place the new cartridge 6 into the body of the tap 8 in exactly the same way.

Note: Be sure that the seal under the cartridge 6 is correctly in place. Make sure that the guides are in the corresponding holes.

☐ Reassemble all the above parts. Tighten the cartridge lock nut 5 using fitting pliers or an

8 GB/IE

miomare

Maintenance and Cleaning/Disposal/Information/Warranty and Service

open-end spanner SW 27 mm while simultaneously securing the fitting from twisting. This will achieve tightness and ensure the handle is not difficult to move.

CAUTION! Be careful not to reverse the hot / cold water plaque 3. The correct position is as follows:

left = red (hot water)

right= blue (cold water).

- Disposal

The packaging is made of environmentally friendly materials, which may be disposed of through your local recycling facilities.

Contact your local refuse disposal authority for more details on how to dispose of your worn-out product.

Information

- Potability of tap water

☐ Find out about the potability of your mains water supply. Your local water authority or water supply company will be able to inform you.

The following general recommendations apply to the potability of tap water:

- Let the water run freely for a short time if it has been stagnating in the pipework for more than four hours. Do not use any of this stagnant water in the preparation of food or for drinking. This applies particularly as far as babies and infants are concerned. Health concerns may otherwise arise. Fresh water can be readily distinguished from stagnant water as fresh water is noticeably cooler as it leaves the pipe.

Do not use stagnant water from chromium-plated pipework to prepare food, for drinking, or for personal hygiene if you are allergic to nickel. This water may contain high quantities of nickel and trigger an allergic reaction.

Do not use water from lead pipework for preparing food baby food and / or to prepare foods during pregnancy. Lead dissolves in drinking water and is particularly damaging to the health of babies and young children.

● Warranty and Service

The warranty period is three years and begins on the day of purchase. Please keep your receipt as proof of purchase.

However, if defects do occur during the warranty period, after first contacting service the defective fitting may be returned freight forward to the service address specified. You will then receive a new or repaired fitting free of charge.

After the warranty period has expired you may also send the defective fitting to the address specified for repair. Repairs made after the expiration of the warranty period are subject to payment.

Note: Eisl Sanitär GmbH will replace defective fittings or supply the respective replacement parts free of charge within the warranty period. Eisl Sanitär GmbH is unable to refund the purchase price for defective fittings.

This warranty does not limit your legal rights.

The warranty period will not be extended by repairs made under warranty. This applies also to replaced and exchanged parts. Complaints are often initiated by difficulties encountered during use. Many of these complaints can be resolved by telephone or email. Please contact the service address set up for you before filing a warranty claim for the fitting with the manufacturer:

Warranty and Service

GB, IE:

Sanifix Limited

Unit 68 Morgan Close

Willenhall

West Midlands

WV12 4LH

United Kingdom

Tel.: [phone]*

E-Mail: [e-mail]

* Free of charge number

IAN 274849

Please have the receipt and item number, e.g.

IAN 12345 ready as your proof of purchase when

making an enquiry.

Product description:

Bath & Shower Mixer Tap

Eisl sanitary No.

NI023DISEWCR-LIDL

Einleitung

links = rot (Warmwasser),

Vertical metallic bar with diagonal shading and a crosshair symbol at the bottom (no text or labels)

Eisl Sanitär GmbH