HBOD 174 - Refrigerator HOOVER - Free user manual and instructions

Product type	Refrigerator with freezer compartment
Brand	Hoover
Model	HBOD 174
Climate class	SN (10-32°C), N (16-32°C), ST (16-38°C), T (16-43°C)
Refrigerant	R600a (isobutane)
Insulating gas	Cyclopentane
Defrost type (refrigerator)	Automatic
Defrost type (freezer)	Manual
Interior lighting	LED
Reversible door hinge	Yes
Power supply	220-240 V, 50 Hz
Temperature adjustment	Rotary thermostat (0-5)
Coldest zone	Indicated by a symbol (some models with OK indicator)
Freezing capacity	Indicated on the rating plate
Maintenance	Clean with warm water and baking soda; vacuum the back
Safety	Disconnect before maintenance; do not use flames for defrosting
Spare parts	Contact authorized after-sales service

Frequently Asked Questions - HBOD 174 HOOVER

How do I adjust the temperature of my Hoover HBOD 174 refrigerator?

Turn the thermostat knob located inside the refrigerator compartment. The higher the number (towards 5), the colder the temperature. Position 0 turns off the appliance.

How do I defrost the freezer?

When the frost layer exceeds 3 mm, set the thermostat to 0, unplug the appliance, remove the food, leave the door open, collect the water, then dry. Never use a flame or sharp object.

Why is my refrigerator making noise?

Noises are normal: humming (compressor), gurgling (refrigerant), clicking (stop). To reduce vibrations, avoid contact between containers and check the fixing of shelves.

How do I reverse the door opening direction?

The reversal must be done by a qualified technician. The manual describes the steps: remove the hinges and reposition them on the other side. This operation is not covered by the warranty.

What should I do if the interior light does not turn on?

Check the power supply, that the appliance is not in position 0, and that the door switch is not blocked. If the problem persists, contact after-sales service.

How do I clean my refrigerator?

Always unplug the appliance before cleaning. Use a cloth with warm water and baking soda or mild soap. Do not use solvents, ammonia, or abrasives. Clean the back with a vacuum cleaner.

Why is there water at the bottom of the refrigerator?

The drain tube may be blocked. Clean it with a stick to allow defrost water to drain.

What foods can be frozen?

Freeze fresh foods in small quantities. Pack them hermetically and label them. Do not refreeze thawed foods. The maximum quantity is indicated on the rating plate.

My refrigerator is not cold enough, what should I do?

Check that the door closes properly, that the seals are tight, that the thermostat is set correctly, and that the appliance is not obstructed. Wait a few hours after adding a lot of food.

What should I do in case of refrigerant gas leak?

Do not use a flame or electrical appliance. Open windows to ventilate the room and immediately contact after-sales service.

USER MANUAL HBOD 174 HOOVER

Congratulations on purchasing this fridge, which has been designed using the latest technologies for an easy-to-use, environmentally friendly appliance.

We recommend you read this guide and the technical datasheet carefully to find out everything you need to know about your new fridge.

Fig. 1

Fig. 4

Fig. 5

Fig. 7

DEFROSTING

MATCHING THE PANELS OF THE BUILT-IN COLUMN TO THE APPLIANCE DOORS

PRODUCT DIMENSION AND BUILT-IN COMPARTMENT.. 17--18

INSTALLATION OF THE APPLIANCE IN THE COLUMN.... 18--18

COUPLING OF THE PANELS OF THE BUILT-IN COLUMN

OF THE APPLIANCE DOORS 19--19

PRECAUTIONS FOR THE CORRECT OPERATION ..... 19--19

SUSPENDING USE OF THE APPLIANCE 19--19

TROUBLESHOOTING 20--20

Thank you for purchasing this product.

Before using your refrigerator, please carefully read this instruction manual in order to maximize its performance. Store all documentation for subsequent use or for other owners. This product is intended solely for household use or similar applications such as:

- the kitchen area for personnel in shops, offices and other working environments

- on farms, by clientele of hotels, motels and other environments of a residential type

- at bed and breakfasts (B & B)

- for catering services and similar applications not for retail sale.

This appliance must be used only for purposes of storage of food, any other use is considered dangerous and the manufacturer will not be responsible for any omissions. Also, it is recommended that you take note of the warranty conditions.

SAFETY INFORMATION

The refrigerator contains a refrigerant gas (R600a: isobutane) and insulating gas (cyclopentane), with high compatibility with the environment, that are, however, inflammable.

We recommend that you follow the following regulations so as to avoid situations dangerous to you:

• Before performing any operation, unplug the power cord from the power socket.
• The refrigeration system positioned behind and inside the refrigerator contains refrigerant. Therefore, avoid damaging the tubes.
• If a leak is noted in the refrigeration system, do not touch the wall outlet and do not use open flames. Open the window and let air into the room. Then call a service centre to ask for repair.
• Do not scrape with a knife or sharp object to remove frost or ice that occurs. With these, the refrigerant circuit can be damaged, the spill from which can cause a fire or damage your eyes.
• Do not install the appliance in humid, oily or dusty places, nor expose it to direct sunlight and to water.
• Do not install the appliance near heaters or inflammable materials.
• Do not use extension cords or adapters.
• Do not excessively pull or fold the power cord or touch the plug with wet hands.
• Do not damage the plug and/or the power cord; this could cause electrical shocks or fires.
• It is recommended to keep the plug clean, any excessive dust residues on the plug can be the cause fire.
• Do not use mechanical devices or other equipment to hasten the defrosting process.
• Absolutely avoid the use of open flame or electrical equipment, such as heaters, steam cleaners, candles, oil lamps and the like in order to speed up the defrosting phase.
• Do not use or store inflammable sprays, such as spray paint, near the refrigerator. It could cause an explosion or fire.
• Do not use electrical appliances inside the food storage compartments, unless they are of the type recommended by the manufacturer.
• Do not place or store inflammable and highly volatile materials such as ether, petrol, LPG, propane gas, aerosol spray cans, adhesives, pure alcohol, etc. These materials may cause an explosion.
• Do not store medicine or research materials in the refrigerator. When storing materials that require strict control of storage temperatures, it is possible that they will deteriorate or an uncontrolled reaction may occur that can cause risks.
• Maintain the ventilation openings in the appliance enclosure or in the built-in structure, free of obstruction.
• Do not place objects and/or containers filled with water on the top of the appliance.
• Do not perform repairs on this refrigerator. All interventions must be performed solely by qualified personnel.
• This appliance can be used by children aged from 8 years and above and by persons with reduced physical, sensory or mental capabilities or with a lack of experience and knowledge, provided that they have been given adequate supervision or instruction concerning how to use the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be made by children without supervision. Turning the knob fully counterclockwise, you will hear a click which corresponds to the switch-off of the product. When the appliance is installed, the electrical cord and the current socket must be easily reached. The socket is compatible with the plug of the appliance. If not, request replacement of the plug by an authorized technician; do not use extension cords and/or multiple connectors. Do not touch the internal parts or frozen food with moist or wet hands as it can cause burns.

Scrapping old appliance

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials. Individuals can play an important role in ensuring that WEEE does not become an environmental issue; it is essential to follow some basic rules:

- WEEE should not be treated as household waste;

- WEEE should be handed over to the relevant collection points managed by the municipality or by registered companies. In many countries, for large WEEE, home collection could be present.

In many countries, when you buy a new appliance, the old one may be returned to the retailer who has to collect it free of charge on a one-to-one basis, as long as the equipment is of equivalent type and has the same functions as the supplied equipment.

Conformity

By placing the C€ mark on this product, we are confirming compliance to all relevant European safety, health and environmental requirements which are applicable in legislation for this product.

INSTALLATION

WARNINGS:

- Do not install the appliance in a damp or wet location as this could compromise the insulation and result in leakage. Furthermore, on the exterior of the same, condensate could accumulate. - Do not place the appliance in locations outside or near sources of heat or exposed to direct sunlight.

The appliance operates properly within the range of environmental temperatures indicated:

+10 +32°C for the climatic class SN +16 +32°C for the climatic class N +16 +38°C for the climatic class ST +16 +43°C for the climatic class T

(See the nameplate of the product)

• Do not place containers with liquids on top of the appliance.
• Wait at least 3 hours after final placement before placing the appliance in operation.

Electrical connection

After shipping, place the appliance vertically and wait at least 2 - 3 hours before connecting it to the electrical system. Before inserting the plug into the electrical socket, make sure that:

• The socket is earthed and in compliance with the law. - The socket can withstand the maximum power load of the appliance, as indicated on the nameplate of the refrigerator. - The power supply voltage is within the amounts indicated on the nameplate of the refrigerator. • The cord must not be folded or compressed. - The cord must be checked regularly and replaced solely by authorized technicians. - The manufacturer declines any liability whenever these safety measures are not respected.

Appliance start-up

Remove all wrapping/packaging present inside the appliance and clean with water and baking soda or neutral soap.

After the installation, wait 2 - 3 hours to allow time for the refrigerator/freezer to stabilize at normal working temperature, before placing fresh or frozen foods inside.

If the power cord becomes disconnected, wait at least five minutes before restarting the refrigerator/freezer. At this point, the appliance is ready for use.

OPERATION

Turning On/Off (no display)

- The thermostat unit for control of the appliance is located inside of the refrigerator compartment (Fig. 1). Rotate the thermostat knob of the thermostat beyond the "0" position. The light is on when the refrigerator door is open. Turning the knob to "0" completely turns off the product.

Fig.1

Temperature adjustment (no display)

Fig. 2

• The temperature adjustment of both compartments is effected by rotating the thermostat knob (Fig. 2). Select the desired position:
• For colder temperature in the refrigerator and in the freezer, by turning towards 5.
• For temperature less cold in the refrigerator and in the freezer, by rotating in the direction of 0.

CONSERVATION

• To maintain the best flavour, nourishment and freshness of foods, it is advisable to store them in the refrigerator compartment as shown in Fig. 6 below, making sure to wrap them in aluminium or plastic sheets or in appropriate covered containers to avoid cross-contamination.

Refrigerator zone

Fruit / Vegetables

- To decrease fruit and vegetable moisture losses they must be wrapped in plastic materials such as, for example, films or bags and then inserted in the fruit/vegetable zone. In this way rapid deterioration is avoided.

FRIDGE ZONE

Indicator of the temperature in the coldest zone (not all models)

Some models are equipped with an indicator of the temperature in the refrigerator compartment in the coldest zone, for you to be able to control the average temperature.

This symbol indicates the coldest zone of the refrigerator (Fig. 5).

Fig. 5

Check that on the temperature indicator, the word OK is clearly shown (Fig. 6). If the word does not appear, this means that the temperature is too high: adjust the temperature to a cooler setting and wait for about 10 hours.

Recheck the indicator: if necessary, proceed with a new adjustment.

Fig. 6

NOTE: If large quantities of food are inserted or the refrigerator door is frequently opened, it is normal for the indicator to fail to show OK. Wait at least 10 hours before adjusting the knob to a higher setting.

Freezer zone

Use the table below for the compartments

Freezing process can only occur in the compartments

Practical recommendations

Place food on the shelves in a homogeneous manner to allow air to circulate properly and to cool it.

• Avoid contact between the food and the far end walls of the refrigerator compartment.
• Do not introduce hot foods as they can cause deterioration of existing ones and increase energy consumption.
• Remove the wrappings of foods before inserting them.
• Do not put in dishes or other containers unless previously washed.
• Do not obstruct the cold air ventilator openings with food.
• Do not cover the glass shelf of the vegetable bin to allow for proper air circulation.
• Do not store bottles in the freezer compartment as they can burst when frozen.
• In the case of prolonged power outage, keep the doors closed so that foods remain cold as long as possible.
• The installation of the appliance in a hot and humid location, with frequent door openings and storing large amounts of vegetables can cause the formation of condensate and affect the performance of the unit itself. • To prevent excessive energy consumption, the frequent or prolonged opening of the doors is not recommended.

FREEZING

• Foods must be fresh.
• Freeze small amounts of food at a time in order to freeze quickly. Never exceed the maximum amount indicated on the rating label.
• During freezing, do not open the freezer door.
• Food must be sealed, airtight.
• Separate food to be frozen by those already frozen.
• Label bags or containers to keep an inventory of frozen foods.
• Once defrosted, do not ever refreeze foods and consume them promptly.

NOTE:

•PRODUCTS WITHOUT DISPLAY

Normally it is not necessary to intervene with the thermostat knob. Only in case you find excessive cooling of the products contained in the refrigerator compartment, gently turning the thermostat knob toward 0 is recommended (Fig. 7).

On completion of freezing, return the knob to the usual position.

Fig. 7

DEFROSTING

Defrosting the refrigerator compartment

During normal functioning, the refrigerator is automatically defrosted. There is no need to dry the drops of water present on the rear wall or to eliminate the frost (depending on functioning).

The water is conveyed to the rear part through the drain hole found there and the heat of the compressor causes it to evaporate.

- Keep the drainage pipe (Fig. 8) clean in the refrigerator compartment to keep it free of water.

The rating plate states the maximum quantity of foods that can be frozen, (see figure 8).

(Figure 8)

Defrosting of the fridge compartment occurs automatically in this product.

We recommend you defrost the freezer area when the layer of frost is more than 3 mm thick.

A small amount of frost or drops of water on the back of the fridge compartment when the fridge is working is normal.

Make sure the water outlet is always clean and make sure foods do not touch the back or sides of the fridge compartment.

N.B. Here you will find your appliance rating plate: it includes all the data to be transmitted to the Customer Service should a fault arise.

Important: if your ambient temperature is high, the appliance may operate continuously, thus building up excessive frost on the inner wall of the fridge. In this case, turn the fridge knob to a warmer setting (1-2).

Defrosting the freezer compartment

(static products without NO-FROST technology)

When the layer of frost present in the freezer compartment exceeds 3mm, it is recommended to proceed with the defrosting as it increases energy consumption.

1) Rotate the knob to the "0" position (Fig. 9)

2) Disconnect the power cord. 3) Remove the frozen food and temporarily place them in a cool place. 4) Leave the freezer door open to speed defrosting. 5) Collect the water on the bottom of the product. 6) Dry the freezer. 7) Reconnect the power cord and set the desired values. 8) Wait a moment and reintroduce the frozen foods.

WARNING:

Absolutely avoid the use of open flames or electrical appliances, such as heaters, steam cleaners, candles, oil lamps and the like to accelerate the defrosting phase.

Do not scrape with a knife or sharp object to remove frost or ice present. These can damage the refrigerant circuit, the leakage of which can cause a fire or damage your eyes.

Defrosting the freezer compartment

(NO-FROST products)

Defrosting is automatic.

MAINTENANCE AND CLEANING

Lighting

LED lighting

The product is equipped with LED lights. Please contact the Technical Assistance Service in case of replacement.

Compared to traditional light bulbs, the LEDs last longer and are environmentally friendly.

Cleaning

NOTICE:

- Before each operation, remove the refrigerator plug from the power socket to prevent electric shocks.

- Do not pour water directly on the outside or inside of the refrigerator itself. This could lead to oxidation and damaging of the electrical insulation.

IMPORTANT:

To prevent cracking of the inside surfaces and plastic parts, follow these suggestions:

• Wipe away any food oils adhered to plastic components.
• The internal parts, gaskets and external parts can be cleaned with a cloth with warm water and baking soda or a neutral soap. Do not use solvents, ammonia, bleach or abrasives.
• Remove the accessories, for example, the shelves, from the refrigerator and from the door. Wash in hot soapy water. Rinse and thoroughly dry.
• The back of the appliance tends to accumulate dust which can be eliminated with the use of a vacuum cleaner, after having switched off and disconnected the appliance from the electrical outlet. This provides greater energy efficiency.

ENERGY SAVINGS

For better energy savings, we suggest:

- Installing the appliance away from heat sources, not exposed to direct sunlight, and in a well-ventilated room.

- Avoid putting hot food into the refrigerator to avoid increasing the internal temperature and therefore causing continuous functioning of the compressor.

- Do not excessively stuff foods so as to ensure proper air circulation.

- Defrost the appliance in case there is ice (see DEFROSTING) to facilitate the transfer of cold.

- In case of absence of electrical energy, it is advisable to keep the refrigerator door closed.

- Open or keep the doors of the appliance open as little as possible.

- Avoid adjusting the thermostat to temperatures too cold.

- Remove dust present on the rear of the appliance (see CLEANING).

AVOIDING NOISES

During its operation, the refrigerator emits some absolutely normal noises, such as:

• HUMMING, the compressor is running. - RUMBLINGS, RUSTLINGS and HISSING, the refrigerant is flowing through the tubes. - TICKS and CLICKS, the operation shutdown of the compressor. Small measures to reduce the vibration noises: - Containers touch each other: Avoid contact between containers and glass recipients. - Drawers, shelves, bins vibrate: Check the proper installation of internal accessories.

NOTE:

The refrigerant gas produces noise even when the compressor is off; it is not a defect, it is normal.

If you hear a clicking sound inside the appliance, it is normal as due to expansion of the various materials.

REVERSIBILITY OF THE DOOR

The doors of the appliance can be reversed to allow opening to the right or left as needed.

NOTE:

- Reversing the doors must be performed by qualified technical personnel.

• Reversing the doors is not covered by the warranty.

REVERSING THE DOOR OPENING

Remove the upper plate and hinge with a screwdriver.

Remove the upper door.

Remove the right bottom hinge and left plastic plugs, and refit them on the opposite side.

Use the spare hinge and cover from the accessories bag, and fit them into the left bottom.

Reassemble the doors and hinges from bottom to top, following steps 1-2.

REVERSING THE FREEZER COMPARTMENT DOOR

PRODUCT DIMENSIONS AND BUILT-IN COMPARTMENT

Insert the appliance into the column, placing it on the opposite side of the hinges, and ensure a 3-5 mm gap.

1

After ensuring the match between appliance door and column door, then screw the appliance upper part to the cabinet

2

Screw the appliance lower part. Fit the seal to the appliance, cut off the

excessive part if necessary. Fit the bottom parts with plastic covers.

3

4

COUPLING OF THE PANELS OF THE BUILT-IN COLUMN OF THE APPLIANCE DOORS

The appliance is equipped with coupling devices for the appliance doors with the column panels (loader slide).

Secure the slide in the inner part of the panel of the built-in column at the desired height and at approx. 20 mm. From the outer wire of the door.

Open the doors of the built-in column and the fridge. Position the built-in loader in the slide, then fit it into the fridge door.

Mark the fixing points for the screws and drill with a bit of a diameter of 2.5mm.

Connect the appliance door to the cabinet panel keeping the loader slots as guidelines.

PRECAUTIONS FOR THE CORRECT OPERATION

Once the product has been embedded, place the rear part of the column in contact with the wall so as to prevent access to the compressor compartment.

For the product to operate correctly it is essential to allow adequate air circulation so as to cool down the condenser located in the rear part of the appliance.

For this reason, the column must be equipped with a rear chimney, whose upper opening must not be blocked, and with a front slot which will be covered with a ventilation grill.

Size of the unit cut outs.

Room to leave between the unit and ceiling.

SUSPENDING USE OF THE APPLIANCE

If the appliance is not to be used for a long time: 1) Turn the appliance OFF (see Operation) 2) Extract the plug or remove the safety device. 3) Clean the appliance 4) Leave the doors of the appliance open.

CAUSE PROBLEM REMEDY

The inside illumination light bulb does not turn on.	Electricity absence.Door switch is blocked.	The power cord is not properly plugged in.Check whether the appliance is switched off.(see Temperature Adjustment).Ensure that there is a current in the house.Check that it is active.
The refrigerator and freezer do not sufficiently cool.	The doors are not closed.The doors are frequently openedErroneous setting of the temperature.The refrigerator and freezer have been excessively filled.Surrounding temperature is too low.No electrical power.	Check that the door and gaskets close properly.Avoid unnecessary opening of the doors for a period of time.Check the temperature setting and, if it is possible, cool even more (see Temperature adjustment)Wait for the stabilization of the temperature of the refrigerator or freezer.Check that the ambient temperature is in accordance with what is indicated on the nameplate (see Installation).The power cord is not properly plugged in.Check whether the appliance is switched off (see Temperature adjustment)Ensure that in the home there is current.
The food in the refrigerator freezes.	Erroneous setting of the temperature.Food in contact with the back wall.The freezing of too much fresh food causes a lowering of the temperature of the refrigerator	Check the temperature setting (see Temperature Adjustment) and, if possible, decrease temperature setting.Separate the food from the back wall of the refrigerator.Do not exceed the maximum amount to be frozen (see Freezing).
The bottom of the refrigerator compartment is wet or droplets are present.	The drain tube could be clogged.	Clean the drain tube with a stick or the like to allow the discharge of water.
Presence of drops or water on the back wall of the refrigerator.	Normal operation of the refrigerator. It is not a defect (see Defrosting).
Presence of water in the vegetable drawer.	Lack of air circulation.Vegetables and fruits with too much moisture.	Verify that your glass shelf tray vegetables are not put foods that prevent air circulation.Wrap the fruit and vegetable materials plastic such as, for example, films, bags or containers.
The motor runs continuously.	The doors are not closed.The doors are opened frequently.Ambient temperature is very high.Thickness of frost than 3mm.	Make sure the doors are closed and if the seals close properly.Avoid unnecessary open ports for a certain period.Verify that the ambient temperature is in accordance with the specifications on the nameplate (see Installation).Set the display/thermostat a warmer temperature.Defrost the unit (see Defrosting).
The frozen food is thawing.	The ambient temperature range below climate class of the product.The compressor starts rarelyThe freezer door is not closed.	Move the unit to a warmer or heat the room.Make sure the door is closed and that the gasket is sealing properly.
WI-FI light flashes 3 sec on - 1 sec off.	Router off.Lacking connection.	Switch the router on.Reset the product (see WI-FI)

IF YOU HAVE NOT SOLVED THE PROBLEM, CONTACT THE SERVICE CENTER. PLEASE GIVE THE TYPE OF FAULT AND THE INFORMATION ON THE PLATE OF THIS APPARATUS TO INSIDE THE REFRIGERATOR COMPARTMENT:

• The model of equipment. • The number of series.

CONTENTS

EN

SAFETY INFORMATION 22--22

INSTALLATION 23--23

OPERATION.... 23--23

STORAGE 24--24

FREEZING 25--25

DEFROSTING.... 25--25

MAINTENANCE AND CLEANING.... 26--26

ENERGY SAVING 26--26

PRODUCT DIMENSIONS AND BUILT-IN COMPARTMENT

BUILT-IN.... 27--28

INSTALLING THE APPLIANCE IN THE COLUMN .... 28--28

ASSEMBLING THE COLUMN PANELS

BUILT-IN APPLIANCE DOORS ..... 29--29

OPERATING PRECAUTIONS

CORRECT 29--29

SUSPEND USE OF THE APPLIANCE 29--29

TROUBLESHOOTING 30--30

Fig. 1

Fig. 5

PRODUCT DIMENSIONS AND BUILT-IN COMPARTMENT

ASSEMBLY OF THE BUILT-IN COLUMN PANELS OF THE APPLIANCE DOORS

PRECAUTIONS FOR CORRECT OPERATION

Fig. 1

Fig. 2

Fig. 5

Fig. 6

NOTE:

PRODUCT AND BUILT-IN RECESS DIMENSIONS

ASSEMBLY OF THE BUILT-IN COLUMN PANELS OF THE APPLIANCE DOORS

Fig. 1

Fig. 5

DIMENSIONS

NOTES FOR CORRECT OPERATION