MAN 2002 - Régulateur Nimo - Free user manual and instructions

USER MANUAL MAN 2002 Nimo

Illustration of a flat-screen computer monitor (no text or symbols visible)

TV

DVD

Users manual for TMURC012

General Description:

The 2 in 1 universal remote control is a new model of preprogrammed universal remote control for European market which has an extensive code library, powerful function and stable quality. It features as:

a. Totally 2 device keys: TV, DVD
b. 4 Operation Modes: Set-up Mode, Manual Search Mode, Auto Search and Display Mode.
c. Back-up memory to keep the set up data no- volatilization.
d. LED flash to indicate when transmission.
e. Set-up indicating LED
f. Device Lock Function
g. Menu Function

Code Set Up:

A. Set Up by brand code:

According to the attached Device Brand Code List, find out the code of the device brand and device code that you want to control. For example, you can find codes for SONY TV: 010, 011, 028, and 030... Then follow the steps as below:

1. Press and hold the [SET] key. Then press the device key that you want to control, such as [TV], [DVD].
2. The LED will be on at moment. Then release the pressed both keys.
3. Enter in the 3-digit Device Code (for example: code 010 under SONY TV).
4. If the entered Device Code is correct, the LED will be off automatically, then gone to step e. If it is incorrect, the LED will blink twice and keep being at set up mode, then return to step c.
5. Try if keys on remote control work or not.

If none key works or some key work but most keys work improperly, please try other codes in the same brand (for example: code 028,030 ...under SONY TV), repeat step a-e till you find one code which work good enough.

Remark: In the process of setup, if you want to quit from setup mode, please press device key. (If no key pressed in 10 seconds, the remote control will leave the set up mode automatically.)

B. Set Up by Manual Search:

After you have set up by device brand code several times, the remote control still doesn't work (i.e. The device still cannot be controlled by this remote control), or you cannot find the correct code in the Device Brand Code List, you can use "Manual Search" to find out the reactive Code:

1. Power on the device that you want to control.
2. Press and hold the [SET] keys. Then press the device key in remote control, such as [TV], etc
3. The LED will be on at moment. Then release the pressed keys.
4. Point the remote control to the device, strike the [POWER] key. If it's DVD, you can press either [POWER] key or [PLAY] key, the remote control enters into" Manual Search" mode and the LED keeps flashing.
5. See if device reacts or not. If it works, turn to step f; if not, repeat step d every 1 second.
6. Test other keys. If keys work well enough, press the device key to quit from the search mode. If most keys don't work well enough, repeat step d-f to find the best code.

Remarks:

a. Whenever you want to leave or change search mode, press the device key to quit, and the LED will turn off.
b. In the Manual Search Mode, besides the [POWER] key ([POWER] key and [PLAY] key in case of DVD), all other keys' function can be checked normally. That is to say you can test other keys without leaving Manual Search mode. It will leave Manual Search mode automatically if no key pressed in 30 seconds.
c. You may use the SET key to change the search direction from forward to backward or from backward to forward.
d. After you press [POWER] 154 times in TV (or 59 times in DVD). If device still does not react from remote control that means this remote control may not work for your device.

C. Set up by Auto Search

This search is similar to Manuel Search except it transmits power signal automatically instead of manually pressing the power key during the search:

1. Power on the device you want to control.
2. Press and hold [SET] key, in the meantime, press and hold the Device key that you want to control (for example: TV) for more than 3 seconds and then release them, the auto search begins. The remote control enters into Auto Search, LED flash, and remote control transmit power signal every 2.0 second automatically.
3. See if device react or not, once the device reacts, press any key (except SET key) to stop the search.
4. Test if other keys work well enough. If most keys don't work well enough, Auto Search again to find next reactive code and try until you find the best code.

Remark:

a. You must point your remote control to the device that you want to control during Auto Search.
b. Whenever you want to leave Auto Search mode, press any key (except SET key) to quit, and the LED will be Off. The search is over.
c. When remote control search through all codes (about 10 minutes), then the remote control will quit from Auto Search process automatically.
d. In case of you did not stop the search on time when device reacted, you may use the Manual Search to search back to find the overlooked code.

Device Lock/Unlock

You can use “Device Lock” function to fix current device code and this device code cannot be changed by code set up or code search. You can use the “Unlock” to quit from this function.

a. Strike the device key that you want to fix such as [TV], [DVD]
b. Press and hold the [SET] key, then press the [7] key, then release the both pressed keys, the LED will blink twice then off, the code of the current device are locked.

c. If you want unlock the current code, press and hold the [SET] key, then press the [8] key, then release the pressed keys, the LED will blink twice and then off, the current code unlocked.

Remark: Only one device can be fixed.

Device Code Display

The device code is a 3-digit number and any one of the 3 digits can be indicated:

1. Strike the device key which code no. You want to display.
2. Press and hold the [SET] key, in the mean time press the digit that you want to display, such as 1, 2, or3.
3. Release the both pressed keys
4. Count the times the LED blinks, and the blinking time is the digit. If there is no blink, the digit is zero.

For example: for code 138

SET+1 (first digit): LED blinks 1 time

SET+2 (second digit): LED blinks 3 times

SET+3 (third digit): LED blinks 8 times

Reset

Use the Reset function to erase all the set up data.

1. Press and hold the [SET] key.
2. Then press and hold the [0] key for more than 3 seconds.
3. Then release the both pressed keys, the LED will blink twice then off, your remote control got reset.

Others

a. After you have finished set-up, first please press the device key (TV or...) on remote control that you want to use, and then operate your remote control normally.

Preprogrammed for almost all brands. Operates all basics functions of your TV, DVD. Menu • Teletext • Colour/brightness • Bass/Treble/Balance • Easy to install.

MAN 2002