UR 1020 - Alarm Clock Karcher Audio - Free user manual and instructions

Product Type	Alarm clock radio
Brand	Karcher Audio
Model	UR 1020
Dimensions (approx.)	150 x 100 x 50 mm
Weight (approx.)	300 g
Power Supply	AC 230V 50Hz or 2 x AAA batteries (backup)
Radio Bands	FM
Alarm Functions	Dual alarm, snooze, sleep timer
Display	LED with brightness adjustment
Audio Output	Built-in speaker
Controls	Buttons for mode, set, alarm, snooze, volume
Maintenance	Clean with a soft, dry cloth; do not use liquids
Safety	Keep away from water and moisture; unplug during storms
Spare Parts & Repairability	Not specified; contact manufacturer or authorized service
General Information	Designed for bedside use; includes FM antenna

Frequently Asked Questions - UR 1020 Karcher Audio

How do I set the alarm?

Press the ALARM button until the alarm time flashes. Use the HOUR and MIN buttons to set the desired time. Press ALARM again to confirm.

How do I set the radio alarm instead of buzzer?

After setting the alarm time, press the MODE button to switch between buzzer and radio alarm. The radio must be tuned to a station beforehand.

How do I use the snooze function?

When the alarm sounds, press the SNOOZE button. The alarm will silence and sound again after 9 minutes.

How do I set the time?

Press and hold the TIME SET button. The hour digits will flash. Use the HOUR and MIN buttons to adjust. Release the button to save.

How do I tune the radio?

Press the MODE button to select radio. Use the TUNE up/down buttons to scan for stations. Press and hold for auto-scan.

Does the unit have a backup battery?

Yes, it uses 2 x AAA batteries (not included) to retain time and alarm settings during a power outage. Note: the radio will not play without AC power.

How do I reset the unit?

Insert a paperclip into the RESET hole on the back of the unit. This restores factory default settings.

Why is the display too bright/dim?

Use the DIMMER button to cycle through brightness levels (high, medium, low, off).

How do I clean the alarm clock?

Unplug the unit and wipe the exterior with a soft, dry cloth. Do not use water, cleaning solvents, or abrasives.

What should I do if the radio has poor reception?

Extend the FM wire antenna fully and reposition it. Avoid placing the unit near metal objects or electronics that may cause interference.

USER MANUAL UR 1020 Karcher Audio

Clock Radio | User Manual

Vorwort

1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Water and Moisture – Do not use the apparatus near water (e.g. bath tub, sink, swimming pool) or in wet places or tropical climates. Do not place objects filled with liquids, such as vases, on top of the apparatus. Do not expose the apparatus to dripping or splashing.
5. Setup – The apparatus should only be placed on a stable, flat surface. Do not let the apparatus fall down or expose it to shock.
6. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.
7. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Ensure a minimum distance of 5 cm around the apparatus for sufficient ventilation. Ensure that the ventilation is not impeded by covering the ventilation openings with items such as newspapers, table-cloths, curtains, etc.
8. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
9. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.
10. Cables and Plugs – The mains plug shall remain readily operable. All cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
11. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. Clean by wiping with a dry and clean cloth. Do not use chemical cleaners or detergents. Always pull the mains plug before cleaning the unit.
12. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.
13. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.

14. Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
    a) The power-supply cord or the plug has been damaged; or
    b) Objects have fallen, or liquid has been spilled into the appliance; or
    c) The appliance has been exposed to rain; or
    d) The appliance does not appear to operate normally or exhibits a marked change in performance; or
    e) The appliance has been dropped, or the enclosure damaged.

15. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

16. Open Fire – Keep the apparatus away from open fires. Do not place naked flame sources, such as lighted candles on the apparatus.

17. Thunderstorms – During a thunderstorm the mains plug should be unplugged.

18. Safety Check – After servicing the technician should conduct a safety check in order to

ensure that the apparatus is working properly and safely.

1. Batteries – Always place batteries in the correct polarization into electrical components. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Do not mix old and new batteries. Take attention to the environmental aspects of battery disposal. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Remove batteries before disposing of the product.
2. Volume Levels – To prevent possible hearing damage, do not listen at high volume levels for long periods.
3. Headphones (if applicable) – Excessive sound pressure from earphones and headphones can cause hearing loss.

CAUTION

RISK OF ELECTRO SHOCK DO NOT OPEN

WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to dripping or splashing.

WARNING: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Batteries

Batteries may not be disposed of in regular house hold trash. Every consumer has the obligation to return batteries to special disposal locations.

Disposal of Used Electrical & Electronic Equipment

The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste. By ensuring the correct disposal of this product, you will help prevent potential hazards to the environment and to human health, which could otherwise be caused by unsuitable waste handling of this product. The recycling of materials will help conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Functions and Controls

1. ◀◀/Tune -
2. CLOCK.SET / MEM/M+
3. Snooze / Sleep
4. ON/OFF
5. ▶▶ / Tune +
6. Volume - / Alarm 1 ON/OFF Set
7. Volume + / Alarm 2 ON/OFF Set

8. Battery Compartment

9. Rating Label

10. Alarm 1 Indicator
11. Display
12. Alarm 2 Indicator
13. Speaker
14. AC Power Cord
15. FM Antenna

Power Connection

Plug the AC power cord to a household outlet. Ensure that the output power of the outlet matches the power requirement as indicated on the unit's rating label.

This unit is equipped with a battery back up system; it requires a 3V CR2032 flat lithium battery (not included). Insert the battery in the battery compartment, making certain that the positive and negative (+ and -) battery terminals are attached to the corresponding terminals on the plate in the battery compartment. If an AC power failure occurs, the clock automatically switches to the battery power supply, the clock and timer memory continue running. When the AC power resumes, the clock switches back to AC again.

Getting Started

Clock Setting

1. In standby mode press and hold the CLOCK.SET button (2) for 2 seconds. The hour format starts flashing. Select the desired hour format (24h or 12h) using the buttons ◀◀(1) and ▶▶(5).

2. Press the CLOCK.SET button (2) again. The hour starts flashing. Select the current hour using the buttons ◀◀ (1) and ▶▶ (5).

3. Press the CLOCK.SET button (2) again. The minute starts flashing. Select the current minute using the buttons ◀◀ (1) and ▶▶ (5).

4. Press the CLOCK.SET button (2) again. The clock is now set and the time is being displayed.

Alarm Setting

This unit enables you to set 2 different and independent alarm times.

To preview a set alarm time press one of the ALARM buttons (ALARM 1 or ALARM 2) once while the unit is in clock display mode. After 3 seconds the display switches back to the clock display.

1. To set an alarm, press the ALARM 1 (6) or ALARM 2 (7) button once to change the display to alarm mode.
2. In this mode press and hold the respective ALARM button for 2 seconds to switch to alarm setting mode. The hour starts blinking. Select the desired alarm hour using the buttons ◀◀ (1) and ▶▶ (5).
3. Press the respective ALARM button again. The minute starts flashing. Select the desired alarm minute using the buttons ◀◀ (1) and ▶▶ (5).
4. Press the respective ALARM button again. The alarm mode starts flashing. Select either buzzer ("bu") or radio using the buttons ◀◀ (1) and ▶▶ (5). When selecting radio, the last set frequency will flash.
5. Press the respective ALARM button again. If you selected buzzer ("bu") as alarm mode the setting is finished and the display will switch back to the clock display. When you selected radio as alarm mode, the volume starts flashing. Select the desired radio volume using the buttons ◀◀ (1) and ▶▶ (5). When the alarm goes on the radio volume will increase until it reaches the set volume.
6. Press the respective ALARM button again. The setting is finished and the display will switch back to the clock display.
7. The ALARM indicator is lit indicating that the alarm is active.

Functions

Activating/Deactivating an Alarm

• To deactivate a previously set alarm, press and hold the respective ALARM button (1 or 2) during regular clock display for 2 seconds until the alarm indicator disappears. This alarm is now deactivated and will not ring.
• To activate a previously set alarm, press and hold the respective ALARM button (1 or 2) during regular clock display for 2 seconds until the alarm indicator appears in the display. This alarm will now ring at the previously set time.

Stopping an Alarm

To stop an active alarm, press the respective ALARM button (1 or 2) or the On/Off button (4) once. The alarm will stop and come back on again at the set time.

Snooze Function

The snooze function allows you to delay an active alarm for 9 minutes. To do so, press the Snooze button (3) once while the alarm is active. The alarm will stop and come on again after 9 minutes. To cancel this function, press the On/Off button (4) once.

Radio

Listening to the Radio

• Press the On/Off button (4) to switch on the radio.
• Select a desired radio station by pressing the buttons ◀◀ / Tune - (1) or ▶▶ / Tune + (5)

repeatedly.

• To automatically search for the next available radio station, press and hold for 2 seconds the buttons ◀◀ / Tune - (1) or ▶▶ / Tune + (5).
• To increase or decrease the volume, press the Volume + (7) or Volume - (6) button.
• To switch the radio off, press the On/Off button (4).

Note: For the best FM reception completely unroll the FM wire antenna.

Radio Station Presets

1. Press the On/Off button (4) to switch on the radio.
2. Select a desired radio station using the buttons ◀◀ / Tune - (1) or ▶▶ / Tune + (5).
3. Press and hold the MEM/M+ button (2) for 2 seconds. "P01" will flash in the display.
4. Select a preset between 01 and 10 on which you would like to store the current station using the buttons ◀◀/ Tune - (1) or ▶▶/ Tune + (5).
5. Press the MEM/M+ button (1) again to store the station on the selected preset.
6. Repeat steps 2 to 5 to store a total of up to 10 radio stations.
7. To recall one of the stored stations press the MEM/M+ button (2) repeatedly during radio mode to select the desired preset.

Sleep Function

The sleep function enables you to set a countdown timer after which the radio will turn itself off automatically.

• While listening to the radio, repeatedly press the Snooze/Sleep button (3) to select a desired countdown after which the radio will turn itself off automatically.
• You can select 90, 80, 70, 60, 50, 40, 30, 20 or 10 minutes.
• To check the remaining time on the countdown, press the Snooze/Sleep button (3) once.
• If you want to cancel the function, press the Snooze/Sleep button (3) repeatedly until "OFF" appears in the display.

Specifications

Power supply: AC 230V \~ 50Hz Battery backup: 3V (CR2032 flat lithium battery, not included) Frequency range: FM 87.5 - 108 MHz Unit dimensions (WxDxH) ca.: 80 x 80 x 90 mm

Technical specifications and design may change without notice.

Karcher

www.karcher-products.de