Scancool

SC 211 SLE - Drink cooler Scancool - Free user manual and instructions

Name: SC 211 SLE
Brand: Scancool
Rating: 8.5 (164 reviews)

Find the device manual for free SC 211 SLE Scancool in PDF.

📄 33 pages

EN ⬇ Download 💬 AI Question ❓ 10 questions ⚙️ Specs

View the manual :

Pick your language and provide your email: we'll send you a specifically translated version.

This manual is not available in your language

Desired language Your email address

Product Type	Drink Cooler
Brand	Scancool
Model	SC 211 SLE
Capacity	Approximately 211 liters
Dimensions (H x W x D)	850 x 600 x 600 mm (estimated)
Weight	40 kg (estimated)
Power Supply	220-240V ~ 50Hz
Power Consumption	120 W (estimated)
Temperature Range	+2°C to +10°C
Cooling Type	Compressor cooling
Adjustable Shelves	Yes, wire shelves
Door Type	Glass door with lock
Interior Light	LED lighting
Defrosting	Automatic defrost
Climate Class	Class N (16°C to 32°C)
Noise Level	< 42 dB(A)
Refrigerant	R600a (environmentally friendly)
Installation	Freestanding, built-in optional
Cleaning	Use mild detergent and soft cloth; avoid abrasive cleaners
Safety Features	Child lock, overheat protection
Spare Parts Availability	Contact Scancool service center
Repairability	Repairable by qualified technician; some parts user-replaceable
Manual Languages	English, German, Swedish, Danish, Dutch (estimated)
Certifications	CE, RoHS

Frequently Asked Questions - SC 211 SLE Scancool

How do I set the temperature on my Scancool SC 211 SLE drink cooler?

Use the electronic control panel on the door. Press SET to enter temperature adjustment mode, then use the UP/DOWN buttons to set the desired temperature between +2°C and +10°C.

My drink cooler is not cooling properly. What should I check?

First, ensure the power cord is plugged in and the circuit breaker is not tripped. Check that the temperature setting is correct. Also, verify that the condenser coils are clean and there is adequate ventilation around the unit.

How often should I clean the condenser coils?

It is recommended to clean the condenser coils every 3 to 6 months to maintain performance. Use a soft brush or vacuum cleaner with a brush attachment to remove dust and debris.

Can I lock the door of the SC 211 SLE?

Yes, the unit is equipped with a key lock. Turn the key clockwise to lock the door and counterclockwise to unlock. Always remove the key after locking to prevent accidental locking.

What is the proper way to defrost the cooler?

The Scancool SC 211 SLE features automatic defrost. However, if manual defrost is needed, turn off the unit, remove all contents, and leave the door open until the ice melts. Do not use sharp objects to remove ice.

How do I change the interior light bulb?

The interior light is LED and should be replaced by a qualified technician. If the light fails, contact Scancool customer service for assistance.

What type of beverages can I store in this cooler?

This cooler is designed for chilled beverages such as canned drinks, bottled water, soft drinks, beer, and wine. Do not store perishable food items requiring precise temperature control.

Can I install the SC 211 SLE under a counter?

Yes, the unit can be used freestanding or built-in. For built-in installation, ensure proper ventilation by leaving 5 cm clearance at the sides and back. Refer to the manual for detailed installation instructions.

What should I do if the cooler makes unusual noises?

Some noise is normal, such as compressor hum or refrigerant flow. If you hear loud or irregular noises, check if the unit is level and on a solid surface. Also, ensure that internal parts are not vibrating against each other. If the problem persists, consult a technician.

Where can I find replacement parts or accessories?

Replacement parts such as shelves, door gaskets, and thermostats can be ordered through Scancool's authorized service centers. Visit the Scancool website or contact customer support for a list of spare parts.

User questions about SC 211 SLE Scancool

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

No questions yet. Be the first to ask one.

Download the instructions for your Drink cooler in PDF format for free! Find your manual SC 211 SLE - Scancool and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SC 211 SLE by Scancool.

USER MANUAL SC 211 SLE Scancool

Original user manual

Please read these instructions completely before operating the units.

SAFETY PRECAUTIONS

To ensure proper use, please thoroughly study these SAFETY PRECAUTIONS before operating the Unit.
The purpose of the safety precautions in this manual is to ensure safe and correct use of the unit to minimize risks that could cause serious damage and injury to you or other persons. The safety precautions are divided into WARNINGS and CAUTIONS. Cases where improper handling of the unit could lead to death or serious injury are listed under the "WARNING" heading. However, the cases listed under the "CAUTION" heading could also lead to serious results. To ensure the safety, adhere strictly to both types of safety precautions.

WARNING: Improper handling of the unit could lead to death or serious injury.

CAUTION: Improper handling of the unit could lead to serious results depending on the circums tance s.

Text set off by the exclamation mark contains information that should be strictly adhered to.
After reading the instruction manual, store it an easily accessible place where the user(s) of this product can easily find it.

PRECAUTIONS FOR INSTALLATION

WARNING

Installation should be performed only by the dealer or a qualified expert. Attempting to install the unit yourself could result in water leakage, refrigerant leakage, electrical shock, or fire.

PRECAUTIONS FOR USE

WARNING!

DONT TAMPER

All repairs, disassembly and modifications should be performed only by qualified technicians. Attempting to perform these yourself could result in a fire, malfunction, and injury.

ELECTRICAL SHOCK HAZARDS

- Never splash water directly onto the product or wash with water as short circuit and electrical leakage could result.

DANGER OF EXPLOSION

- Never put flammable or volatile substances into the unit as explosion and fire could result.

PROHIBITED

- Do not damage, modify, excessively bend, strain, twist or bundle up the power cord.

Also, placing heavy objects the power cord or squeezing it in a tight place could damage it, possible resulting in electrical shock or fire.

PROHIBITED

- Use a dedicated wall outlet. Do not use extension cords or convenience receptacles as this could result in electrical shock, overheating and a fire.

FLAMMABLE

- Never use flammable spray cans or leave flammable substances near the unit. Sparks from electrical switches could result in explosion and fire.

WARNINGS

- The cooler is intended for storage and display of beverages for sale. Do not use for other purpose than intended as this could adversely affect items placed in the unit.

- For indoor use only. Using the unit in a location exposed to rain could result in electrical leakage and electrical shock.

- Install the unit in a location where the floor is sturdy enough to support the load of the unit. Li the lloor is not sturdy enough or installation is incorrectly performed, the unit could tip over and falling shelves and products could cause personal injury.

- Store the unit in a location where it is not exposed to rain. Using a unit that has been exposed to rain could result in electrical leakage and electrical shock.

- Leave disassembly and disposal of the unit to qualified experts.

- Never attempt to insert fingers, sticks, etc. into the cold air suction outlet as a circulation fan is rotating at high speed inside the outlet. Injury, electrical shock and improper operation could result.

- Never place heavy objects or items containing water on top of the unit. Objects could fall down and cause injury and spilled water could deteriorate the insulation of electrical components and result in electrical leakage.

- If you find gas leakage, please don't touch the chest freezer, and close gas and open the door for ventilation. Gas leakage could cause explosion, fire, and fire injury.

- Keep away from hot air sources

Cooling performance is reduced if the unit is placed near heat sources such as hot plates and staves and if it is exposed to direct sunlight.

- Should the unit need temporary storage, make sure not to store the unit in a location where children play and take precautions so that the door cannot be completely closed. This will minimize the risk that a child becomes trapped inside the compartment.

WELL VENTILATED PLACE

Please make sure there is more than 10cm space between upright cooler and the wall. If there is no space, cooling capacity can drop down.

DANGER OF ELECTRICAL SHOCK

If installation in a damp location is unavoidable, also install an electrical leakage circuit breaker. If no electrical leakage circuit breaker is installed, electrical shock could result.

PROHIBITED

Never hang from the door or climb onto the unit. The unit could tip over or fall and cause material damage or injury.

DO NOT PINCH FINGERS

Grasp the handle when closing the door. Holding at other positions could result in pinched fingers and injury.

- When disconnecting the power cord plug from the wall outlet, hold at the plug main body close to the outlet. Pulling the cord could cause wire breakage, possibly resulting in overhealing and fire.

Do not throw items onto the shelves and do not place items totaling more !han 651bs on each shelf. The shelf could fall down, possibly ca using injury.
Disconnect the power cord plug from the wall outlet before moving the unit and make sure that the power cord is not damaged during transport. A damaged power cord could result in electrical shock and/or fire.
Do not push hand against or apply excessive force to glass surfaces as the glass could break and cause injury.
Make sure that the unit does not tip over or fall when it is moved. A falling unit could cause serious injury.
Be sure to attach and secure shelves correctly. An improperly attached shelf could fall down and cause injury.

BEFORE USE

Remove shipping package, tape, etc, and leave doors open ventilate fora while.

The unit is cleaned before shipment. However, clean the compartment interior after delivery.
Please insert power supply plug into the wall outlet, single-phase to cat voltage.
Allow the unit to operate for about 1 hour to cool the compartment before placing items in the cooler.

WAIT 5 MINUTES OR MORE BEFORE RE- STARTING

- Restarting the unit immediately after it has been turned off may cause fuses to blow and activate the circuit-breaker, the compressor may be overloaded, and/or other damage may occur.

DRAIN TRAY

Defrosting is performed automatically and drain water is collected in the drain tray.
Water in the drain tray is evaporated automatically. In humidity, there is a large amount of water in the drain tray, so please throw away drain water once a day.

EFFICIENT USE

To prevent cold air from escaping, open and close the door quickly and keep the door opened for as short a time as possible.
Please install the unit in the place which is well-ventilated.

SHELF HEIGHT ADJUSTMENT

The shelf height can be adjusted.

Arrange the shelves in accordance with the dimensions of the items to be placed in the cooler.

PLACING ITEMS IN THE SHOWCASE

This showcase employs a forced circulation of cold air system. If circulation of cold air is obstructed, the items will not be adequately refrigerated. Pay attention to the following points:

Do not let items obstruct the cold air inlet and suction outlet.
Place items so that they do not protrude from the shelves. The gap between the shelves and the
• Door is used for circulation of cold air.
Place items evenly on all shelves.

WARNING

To prevent any electrical shock hazards or injury by rotating circulation fan, always' disconnect the power cord plug from the wall outlet before cleaning.

EXTERIOR AND COOLER COMPARTMENT

Wipe with a saft, drycloth. If very soiled, wipe with a cloth that has been moistened with a detergent Then wipe with a cloth that has been dipped in water.

WARNING: Do not splash water directly onto the cooler and do not wash with water. ] Short - circuit andelectrical shock could result.

Clean the cooler regularly to keep it clean at all times.
Never use polishing powder, soap powder, benzine, oil or hot water as these will damage the painting and plastic components.

CHECKS

To ensure the safety, perform the following checks after cleaning.

Is the power cord plug firmly inserted into a dedicated wall outlet? Confirm that the plug is not abnormally hot.
Check the power cord for cracks and damage. Should the slightest irregularity be observed, contact the dealer from whom you purchased this unit or our customer's service.

IN CASE OF THE FOLLOWING

POWER FAILURE

Keep opening and closing of the door to a minimum.

Avoid placing new items in the cooler as this will raise the temperature inside the compartment.

WHEN NOT USED FOR A LONG PERIOD

Remove all items from the compartment and disconnect the power cord plug from the wall outlet. Clean the compartment interior and wipe away all water.

To prevent mold formation and bad smell, leave the door open to dry the compartment completely.

TRANSPORTATION

Disconnect the power cord plug from the wall outlet.

When moving the cooler, make sure that the teet do not damage the power cord. Do not let the teet hit against floor steps, thresholds, etc.

TEMPORARY STORAGE

Affix a piece of wood, etc. Between the door and main unit to prevent complete closing of the door. Make sure not to store the unused cooler at a location where children play.

Should a child enter the compartment and the door is closed, the child may not be able to open the door from the inside.

BEFORE REQUESTING SERVICE

Please check the following items if you encounter problems with the unit. If the problem continues after taking the proper remedial actions, disconnect the power cord plug from the wall outlet.

Transfer the items stored in the cooler to a box or other container. Then contact the dealer from whom you purchased this unit and be ready to provide information as listed in "REQUIRED INFORMATION" below.

CAUTION

To prevent any electrical shock ha zards, do not disconnect the power cord plug from the wall outlet with wet hands.

Light source in this product is replaceable only by a professional.

BEFORE REQUESTING SERVICE

No refrigeration at all

• Is the power supply interrupted?
• Is the power cord plug disconnected from the wall outlet?
- Are the shop's power fuses blown and/or the circuit breaker activated?

Inadequate refrigeration

• Is the temperature setting appropriate?
- Are items obstructing the cold air inlet and suction outlet?
• Are stored items packed too tight?
• Is the door open or is it opened and closed frequently?
• Is the condenser clogged?

Excessive noise

• Are all teet in firm contact with the floor?
- Is the rear panel of the cooler contacting the wall or other objects?
• Are other objects in contact with the cooler?

Condensation on cooler exterior

Condensation may condense on the exterior and door during hot and humid days or depending on the place of installation. This occurs when the humidity is high and water particles in the air contact cold surfaces. This is normal.wipe away condensation with a dry cloth.

Showcase sometimes stop running when thermostat turns off.

Elitech ECS-16 Temperature Controller User Manual

General

The temperature controller is specially designed for beverage cabinet. It has user menu and administrator menu.

Control temperature could be set through user menu; and for administrator menu, it has password protection to avoid misoperation. It can switch between heating and refrigeration mode, and the relay capacity is 30A, which could directly drive a single phase 1.SHP compressor. Defrost output is optional and defrost mode could be either natural defrost or in electric defrost (defrost relay needs to be selected). Colorful LED display, and work status is displayed in symbols. It adopts plug-in quick connection terminal, which highly simplify the processing for manufacturers.

Operation and display panel

Scancool SC 211 SLE - Operation and display panel - 1

Specification

Mounting size: 71×29 (mm)

Product size: 78.5 × 34.5 × 82 mm

Technical parameters

Measuring rang: -50^ +90^

Resolution: 1°C

Accuracy: -50^50^,±1^, others, ±2^

Cabinet temperature control range: -50^ 85^

Power supply: 220VAC±10% 50/60Hz

Refrigeration: 30A/240VAC, directly drive a single phase 1.5HP compressor;

Defrost: 5A/250VAC (optional)

Front panel protection level: IP65 9

Ambient temperature: 0°C\~55°C

Storage condition: ...... temperature -25 °C\~75°C

Storage humidity: 20%\~85% (non condensing)

Indicator light status description

Indicator light	Symbol	Status	Meaning
Setting	SET	ON	Parameter setting
Setting	SET	OFF	Status of temperature measuring and controlling
Control load	out	ON	Control load works
		OFF	Control load stops
		FLASH	Control load in time delay
Heating mode	H	ON	Start heating mode
Refrigeration mode	C	ON	Start refrigeration mode
Defrost	def	ON	Start defrosting

Parameter list

Menu	Menu function	Setting range	H1	H2	Unit
User Menu
St	Set temperature	Min. set temperature C3~Max. settemperature C4	3	3	°C
Po	Menu password	0~99 (password is 55, irreversible)	0	0	/
Administrator Menu
rd	Temperature hysteresis	1~15	4	6	°C
C1	Temperature sensor calibration	-10 ~10	0	-3	°C
C2	Control load start delay	0~60	1	2	min
C3	Min. set temperature	-50 ~St	0	0	°C
C4	Max. set temperature	St~85	10	6	°C
A1	Periodical open time after sensor failure	1~60	45	45	min
A2	Periodical close time after sensor failure	0~600:close control load after sensor failure	15	15	min
d1	Defrost cycle	0~900:Defrost forbidden	6	12	hour
d2	Defrost time	1~90	20	20	min
d3	Display during defrost	0:Display cabinet temperature1:Display dF during defrost2:Display defrost start temperature during defrost	2	2	/
HC	Refrigeration/heating switch	0:Refrigeration1:Heating	0	0	/

Keys function

Keys	Function
Set	Enter the status of parameter setting
Set	Switch between menu and parameter
	Adjust menu and parameters
	Adjust menu and parameters ;
	Press 10s to execute parameter one-key recovery
	Exit from parameter setting status
	Exit from one-key recovery status
	Force to start defrost

User parameter setting

In the status of temperature measuring and controlling, press Set key for three seconds to enter user parameter setting state, it displays menu St in the digital tube. At this time, press Set key to display the corresponding parameter value, and press on to adjust the set temperature, and then press Set key to return to menu item St.

In the state of user menu setting, when it displays menu item St in the digital tube, press to switch to the menu item Po, press Set key to display 00, and press and to adjust it to 55, then press Set key again to return to menu item Po. At this time, press key to display rd, indicating that it has entered to the administrator parameter

setting status.

If it doesn't adjust to 55, press Set key to return to menu time Po, then press the key ▲it will exit from user parameter setting status and return to the temperature measuring and control status.

Administrator parameter setting

After enter to the administrator parameter setting, press and to select menu items (St, Po, rd.....);

Scancool SC 211 SLE - Administrator parameter setting - 1

After select the item, press Set key to enter to the current parameter setting, press ▲ and ▼ to adjust parameters, and then press Set key to return to the menu item.

Exit from parameter setting

Under the status of parameter setting, press key or no key operation within 30s, or if Po is not set as 55, press key when it displays menu item Po (i.e. password input error), it will save the current parameter value and exit from parameter setting.

Manual defrost

In the status of temperature measuring and controlling, Press . For three seconds to force the open or close of defrost( d1 is not 0, i.e. defrost is not forbidden).

Parameter recovery

In the status of temperature measuring and controlling, press key for 10S, display H0 in the digital tube, it will execute one key recovery operation. It could continue to select the parameter recovery items by pressing key, and the selection range is H0 \~ H7, press key to execute the parameter recovery and then exit, if there is no parameter recovery operation within 30S, it will automatically exit from the mode without recovery of parameters.

Note: During the operation of one key recovery, it needs a stable power supply. If the power supply is not stable, please electrify the controller again then execute one key recovery.

H0	Give up parameter recovery, no change of each parameter, no display of parameter recovery success code dr
H1	Recovery parameter H1, recovery success display dr
H2	Recovery parameter H2, recovery success display dr
H3	Reserved
H4	Reserved
H5	Reserved
H6	Reserved
H7	Reserved

Control output

Refrigeration/heating:

Normal status:

HC=0, refrigeration mode:

When the cabinet temperature is higher than the set temperature+ hysteresis temperature, and finish the control load start delay time, the refrigeration will start; When the cabinet temperature is lower than the set temperature, the refrigeration will close.

HC=1, heating mode:

When the cabinet temperature is lower than the set temperature, and finish the control load start delay time, the heating will start: When the cabinet temperature is higher than the set temperature + hysteresis temperature, the heating will close.

Note: For the initial use of controller, the control output start delay time is calculated as 3s, and in the future, it is calculated as C2(Control load start delay) In heating model, it needs to set d1 to 0 (Defrost forbidden)

Sensor failure:

A2=0, the function of "Run/stop in a proportional time" is canceled, the control output closes;

A2≠0, the function of "Run/stop in a proportional time" opens, the control output will run and stop periodically according to the set time after the sensor fails.

Defrost:

If the defrost cycle is not 0, the controller will start defrost when it finishes defrost cycle or it can be manually started. Defrost stops when finish defrost time or it could be manually stopped.

Display during defrost:

d3=0: Display real time cabinet temperature

d3=1: Display dF during defrost

d3=2: Display defrost start temperature during defrost

Code	Reason	Control output	Remark
E1	sensor failure	Run/stop control output in a proportional	/
dF	Defrost	With defrost relay: output defrost	/
dF	Defrost	Without defrost relay: off cycle defrost	/
dr	Parameter recovery	The original parameters will be overwritten by the selected parameters	Factory operation mode

Wiring diagram

Scancool SC 211 SLE - Wiring diagram - 1

text_image

Elitech® 30V/m 1 2 3 N L N 22V/WAC 55/60Hz + - + - + - + - + -

Danger:

Strictly distinguish the power wire, relay output, sensor down-lead and data line, and therelay could not be overloaded.

Prohibit connecting the wire terminals without electricity cut-off.

Warning:

Prohibit using this unit under the environment of over damp, high temp., strong electromagnetism interference or strong corrosion.

Notice:

The power supply should conform to the voltage value indicated in the instruction, and make sure a steady power supply.
To avoid the possible interference, the sensor down-lead/data line and power wire should be kept in a proper distance.

BRUKSANVISNING