R 1250 RT (2020) - Motorcycle BMW - Free user manual and instructions

Product Type	Motorcycle
Brand	BMW
Model	R 1250 RT (2020)
Engine Displacement	1,254 cc
Engine Power	100 kW (136 hp) at 7,750 rpm
Torque	143 Nm at 6,250 rpm
Transmission	6-speed constant mesh
Fuel System	Electronic intake pipe injection / BMS-X
Front Suspension	BMW Telelever
Rear Suspension	BMW Paralever
Brakes Front	Dual disc
Brakes Rear	Single disc
ABS	BMW Motorrad Integral ABS (partial integral)
Length	2,222 mm
Width (with mirrors)	1,004 mm
Height (without mirrors)	1,410 mm
Seat Height	805/825 mm (standard/optional low)
Wheelbase	1,555 mm
Unladen Weight (road ready)	279 kg
Fuel Tank Capacity	25 L
Front Tire	120/70 ZR 17
Rear Tire	180/55 ZR 17
Display	TFT color screen with connectivity
Additional Features	Heated grips, cruise control, navigation preparation, Keyless Ride (optional)

Frequently Asked Questions - R 1250 RT (2020) BMW

What type of oil is recommended for the BMW R 1250 RT?

BMW recommends a fully synthetic 5W-40 oil meeting BMW specification BMW Longlife-04 or API SN/ACEA A3/B4. Always check the owner's manual for exact specifications.

How do I adjust the suspension on the R 1250 RT?

The R 1250 RT features electronic suspension adjustment (Dynamic ESA). You can select riding modes (Road, Dynamic, Rain, Eco) via the mode button on the handlebar, which automatically adjusts damping. Manual adjustment of spring preload is available via a knob on the rear shock.

What is the fuel consumption of the BMW R 1250 RT?

Official combined fuel consumption is approximately 4.8 L/100 km (49 mpg US). Real-world consumption varies based on riding style and conditions.

How do I pair my smartphone via Bluetooth?

Ensure your phone's Bluetooth is enabled. On the TFT display, go to Settings > Connectivity > Pair smartphone. Follow the on-screen instructions. The system supports phone calls, music, and navigation prompts.

What is the correct tire pressure for the R 1250 RT?

Recommended tire pressures (cold) are: Front 2.5 bar (36 psi), Rear 2.9 bar (42 psi) for solo riding. For two-up or heavy loads, increase rear to 3.0 bar (43.5 psi). Always refer to the sticker on the swingarm.

How do I replace the battery?

The battery is located under the seat. Remove the seat (two screws or quick-release). Disconnect negative (-) terminal first, then positive (+). Remove the battery hold-down bracket and lift out. Install new battery with proper orientation (vent hose attached). Reconnect positive first, then negative. Perform a reset of the clock and settings if needed.

What is the service interval for the R 1250 RT?

BMW recommends service every 10,000 km (6,000 miles) or 12 months, whichever comes first. This includes oil change, filter check, and general inspection. Valve clearance check is every 20,000 km (12,000 miles). The service indicator will remind you.

Can I add a top case or side cases?

Yes, the R 1250 RT is designed for BMW's optional system cases. Side cases (each 31 L) and top case (49 L) are available. They attach via quick-release mechanisms built into the bike. Ensure you use genuine BMW mounts for proper fit and safety.

How do I use the cruise control?

Activate cruise control by pressing the CRUISE button on the right handlebar. Accelerate to desired speed, then press SET/- to lock. Adjust speed with RES/+ or SET/-. To deactivate, press CRUISE again, pull the brake or clutch lever, or roll off the throttle.

What does the 'Service due' warning mean?

The warning indicates that a scheduled service is overdue based on mileage or time. The display will show Service due with a wrench icon. It is recommended to visit an authorized BMW Motorrad workshop to perform the required inspections and reset the service indicator.

USER MANUAL R 1250 RT (2020) BMW

Údaje o vozidlu

Model

Declaration of con- formity for charging

compartment 337

SEZNAM HESEL 342

VŠEOBECNÁ UPOZORNĚNÍ

01

ORIENTACE 4

ZKRATKY A SYMBOLY 4

VÝBAVA 5

TECHNICKÉ ÚDAJE 5

AKTUÁLNOST 5

DALŠÍ INFORMAČNÍ ZDROJE 6

CERTIFIKÁTY A SCHVÁLENÍ K PROVOZU 6

DATOVÁ PAMĚŤ 6

INTELIGENTNÍ SYSTÉM TÍSŇOVÉHO VOLÁNÍ 10

4 VŠEOBECNÁ UPOZORNĚNÍ

ORIENTACE

CELKOVÝ POHLED NA KOKPIT 18

CELKOVÝ POHLED NA KOKPIT

The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line or separator), not a placeholder for text. According to Rule 2, such stylistic/background lines must be ignored by the OCR result. The OCR content provided is "", which consists of no characters. This correctly represents the line in the GT by ignoring it entirely. Since the OCR output includes no underscores for this line, this complies with the “Stylistic/Background Lines (Ignore)” rule. Therefore, the OCR result is consistent with the Ground Truth.
The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line or separator), not a placeholder for text. According to Rule 2, such stylistic/background lines must be ignored by the OCR result. The OCR content provided is "", which consists of no characters. This correctly represents the line in the GT by ignoring it entirely. Since the OCR output includes no underscores for this line, this complies with the “Stylistic/Background Lines (Ignore)” rule. Therefore, the OCR result is consistent with the Ground Truth.
The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line or separator), not a placeholder for text. According to Rule 2, such stylistic/background lines must be ignored by the OCR result. The OCR content provided is "", which consists of no characters. This correctly represents the line in the GT by ignoring it entirely. Since the OCR output includes no underscores for this line, this complies with the “Stylistic/Background Lines (Ignore)” rule. Therefore, the OCR result is consistent with the Ground Truth.
The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line or separator), not a placeholder for text. According to Rule 2, such stylistic/background lines must be ignored by the OCR result. The OCR content provided is "", which consists of no characters. This correctly represents the line in the GT by ignoring it entirely. Since the OCR output includes no underscores for this line, this complies with the “Stylistic/Background Lines (Ignore)” rule. Therefore, the OCR result is consistent with the Ground Truth.
The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line or separator), not a placeholder for text. According to Rule 2, such stylistic/background lines must be ignored by the OCR result. The OCR content provided is "", which consists of no characters. This correctly represents the line in the GT by ignoring it entirely. Since the OCR output includes no underscores for this line, this complies with the “Stylistic/Background Lines (Ignore)” rule. Therefore, the OCR result is consistent with the Ground Truth.
[Non-Text]
[Non-Text]
The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line or separator), not a placeholder for text. According to Rule 2, such stylistic/background lines must be ignored by the OCR result. The OCR content provided is "", which consists of no characters. This correctly represents the line in the GT by ignoring it entirely. Since the OCR output includes no underscores for this line, this complies with the “Stylistic/Background Lines (Ignore)” rule. Therefore, the OCR result is consistent with the Ground Truth.
[Non-Text]
The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line or separator), not a placeholder for text. According to Rule 2, such stylistic/background lines must be ignored by the OCR result. The OCR content provided is "", which consists of no characters. This correctly represents the line in the GT by ignoring it entirely. Since the OCR output includes no underscores for this line, this complies with the “Stylistic/Background Lines (Ignore)” rule. Therefore, the OCR result is consistent with the Ground Truth.
[Non-Text]
[Non-Text]
The Ground Truth image displays a single, solid horizontal line, which is a stylistic or background element (like a ruled paper line). According to Rule 2, such lines must be ignored by the OCR result. The provided OCR content is "____", which consists of underscores. Underscores are not equivalent to a solid line and are not permitted under the “Stylistic/Background Lines (Ignore)” rule. Outputting underscores for a stylistic line is incorrect because it misinterprets the line as a fill-in-the-blank placeholder. Hence, the OCR result is inconsistent with the Ground Truth.
[Non-Text]
[Non-Text]

36 UKAZATELE

Service over- (56) due!

Venkovní teplota

Remote key not in range. Not possi- to switch on igni- n again.

Možná příčina:

Remote key battery weak. Limited central locking function. Change battery.

Možná příčina:

Vehicle voltage critical! Consumers

were switched off. Check battery condition.

Vehicle voltage low. Switch off

unnecessary consumers.

Battery voltage critical! Accident k. Stop driving.

VAROVÁNÍ

Front right turn indicator faulty!

Low-beam headlight faulty!

Front side light faulty!

Daytime riding light faulty!

Left additional headlight faulty!, popř.

Bight additional headlight faulty!

Tail light faulty!

40 UKAZATELE

Brake light faulty!

servis, nejlépe na partnera BMW Motorrad.

Rear left turn indicator faulty!, popř.

Rear right turn indicator faulty!

Baterie DWA je slabá

Number plate light faulty!

Alarm system batt. capacity weak. No

restrictions. Make an appointment at a specialist workshop.

- Have it checked by a specialist workshop.

bliká žlutě.

Active headlight faulty.

Možná příčina:

Alarm system battery empty. No independent alarm. Make an appointment at a special workshop.

Engine oil level Check engine oil

level.

Možná příčina:

Coolant temperature too high! Check co-nt level. Continueving in part. load to l down.

POZOR

Engine! Have it checked by a specia-workshop.

Možná příčina:

No communication with engine cont- . Multiple sys. af- ted. Ride carefully the next specialist kshop.

Fault in the engine control. Onward

journey possible Ride carefully to next speci- alist workshop.

VAROVÁNÍ

Serious fault in the engine control! Ri-g at mod. speed pos.

Damage possible. Have checked by workshop.

VAROVÁNÍ

Tyre pressure does not match setpoint Check tyre pressure.

Možná příčina:

Tyre pressure does not match setpoint Stop immediately! Check tyre pressure.

Tyre press. control. Loss of pressure. Stop immediately! Check tyre pressure.

VAROVÁNÍ

RDC sensor battery weak. Function limi- Have it checked by a cialist workshop.

Drop sensor faulty. Have it checked by a

specialist workshop.

Možná příčina:

Emergency call failure. Make an ap-

pointment at a specialist workshop.

Side stand monito- ring faulty. Onward

journey possible. Engine stop. when stationary! Have checked by workshop.

Možná příčina:

Limited ABS availability! Onward journey possible. Ride carefully to next specialist workshop.

ABS failure! Onward journey possible.

Ride carefully to next specialist workshop.

Možná příčina:

possible. Ride carefully to next specialist workshop.

Možná příčina:

Traction control de-activated.

Možná příčina:

Traction control limited! Onward journey possible. Ride carefully to next specialist workshop.

Možná příčina:

Traction control failure! Onward journey possible.

Ride carefully to next specialist workshop.

Možná příčina:

Spring strut adjustment faulty! Onward journey possible. Ride carefully to next specialist workshop.

Možná příčina:

refully to cool down.

Avoid dynamic riding.

NEBEZPEČÍ

Brake temp. critical! Continue riding

carefully to cool down. Avoid dynamic riding.

NEBEZPEČÍ

Active cruise control failed. Onward

journey possible. Drive to nearest workshop.

54 UKAZATELE

Možná příčina:

ACC temporarily fai- led. Onward journey possible.

Možná příčina:

Distance control failed. Onward journey possible. Drive carefully to nearest workshop.

Možná příčina:

Service due! Have service performed by a specialist workshop.

Možná příčina:

Service overdue! Have service performed by a specialist workshop.

Možná příčina:

1 Nouzový vypínač

Ukazatele směru

- Spínač 1 posuňte doleva. naSystém se vypne.

zhasne.

Demontáž kufru

- Mobile device - Rider's helmet - Passenger helm.

•Vyvolejte menu Navigation, Active route guidance.
• Vyberte a potvrd'te End route guidance.

•Vyvolejte menu Navigation, Active route guidance.

•Vyvolejte menu Navigation, Active route guidance.
- Vyberte a potvrd'te Current instruction.

MÉDIA

Předpoklad

•Vyvolejte menu Media.

playing, All artists, All albums nebo All tracks.

-Vyberte Playlists.

-Vyberte Output device.

-Vyberte Sound profile.

-Nastavte Equaliser.

! VAROVÁNÍ

se

• Vyklopte ochrannou krytku

POZOR

POZOR

VAROVÁNÍ

POJISTKY

Výměna pojistek

POZOR

1 50 A

1 15 A

OŠETŘUJÍCÍ PROSTŘEDKY

MYTÍ MOTOCYKLU

ELEKTRICKÁ INSTALACE

DECLARATION OF CONFORMITY FOR CHARGING

COMPARTMENT

337

Declaration of Conformity

Radio equipment electronic immobiliser (EWS)

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period

Technical information

Frequency Band: 134 kHz (Transponder: TMS37145 / TypeDST80, TMS3705 Transponder Base Station IC) Output Power: 50 dBμV/m

Manufacturer and Address

Hereby, BECOM Electronics GmbH declares that the radio equipment type EWS4 is in compliance with Directive 2014/53/EU53 The full text of the EU declaration of conformity is available at the following internet address: http://www.becom.at/de/download/

Greece

Hereby, BECOM Electronics GmbH declares that the radio equipment type EWS4 is in compliance with Directive 2014/53/EU53.

The full text of the EU declaration of conformity is available at the following internet address: http://www.becom.at/de/download/

Italy

Ring aerial in the ignition switch

To verify the authorization of the ignition key, the electronic immobilizer exchanges information with the ignition key via the ring aerial.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly

approved by the party responsible for compliance could void the user's authority to operate the equipment.

Certifications Remote Control for central locking system

Česky

Hereby, Meta System S.p.A., declares that this PF240009 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Español

Product name: TX BMW

MR FCC ID: P3O98400

IC:4429A - TXBMWMR

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Declaration Of Conformity

R&TTE Declaration Of Conformity (DoC)

CE0470

We:

Meta System S.p.A.

with the address:

Via Majakovskij 10 b/c/

d/e 42124 Reggio

Emilia -Italy

Declare

Under own responsibility that the product:

TX BMW MR

To which this declaration relates is in conformity with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC).

This product is in conformity with the following standards:

Health & Safety (art.3.1)

EN 60950-1

EMC (art.3.2) Spectrum

ETSI EN 301 489-1/-3

Human exposure

ETSI EN 300 220 - 2

EN 62311

According to Directive 1999/5/

CE Reggio Emilia, 14/07/2010

Technical

Director Lasagni

Cesare

Declaration of Conformity

Radio equipment Keyless Ride

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period

Technical information

Frequency band: 434,42 MHz Maximum Transmission Power: 10 mW

Manufacturer and Address

Manufacturer: Huf Hülsbeck & Fürst GmbH & Co. KG Adress: Steeger Str. 17, 42551 Velbert, Germany

Bülgarski

Hereby, Huf Hülsbeck & Fürst GmbH & Co. KG declares that the radio equipment type HUF5750 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.huf-group.com/eudoc

Español

USA, Canada:

Product name: BMW Keyless Ride ID

Device FCC ID: YGOHUF5750

IC: 4008C-HUF5750

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

Canada:

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

USA:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Argentina:

Declaration Of Conformity

We declare under our responsibility that the product

BMW Keyless Ride ID Device (Model: HUF5750)

camplies with the appropriate essential requirements of the article 3 of the R&TIE and the other relevant provisions, when used for its intended purpose. Applied Standards:

1. Health and safety requirements contained in article 3 (1) a)

- EN 60950-1:2006+A11:2009+A1:2010+A12:2011; Information technology equipment-Safety

1. Protection requirements with respect to electromagnetic compatibility article 3 (1) b)

- EN 301 489-1 (V1 .9.2, 09/2011 ), Electromagnetic compatibility and radio spectrum matters (ERM); Electromagnetic compatibility (EMC) standard for radio equipment and services;

Part 1: Common technical requirements

- EN 301 489-3 (V1.4.1, 08/2002) Electromagnetic compatibility and radio spectrum matters (ERM); Electromagnetic compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for short range devices (SRD) operating on frequencies between 9 kHz and 40 GHz

1. Means of the efficient use of the radio frequency spectrum article 3 (2)

- EN 300 220-1 & -2 (V2.4.1, 05/2012), electromagnetic compatibility and radio spectrum matters (ERM); Short range devices (SRD); Radio equipment tobe used in the 25 MHz to 1000 MHz frequency range with power levels ranging up to 500 mW;

Part 1: Technical characteristics and test methods.

Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TIE directive

The product is labeled with the CE marking:

CE

Velbert, October 15 ^th , 2013

Product Development Systems Car Access and Immobilization - Electronics Huf Hülsbeck & Fürst GmbH & Co. KG

Steeger Straße 17, D-42551 Velbert

Declaration of Conformity

Radio equipment tyre pressure control (RDC)

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period

Technical information

Frequency Band: 433.895 - 433.945 MHz Output Power: <10 mW e.r.p.

Manufacturer and Address

Manufacturer: Schrader Electronics Ltd. Adress: Technology Park, Antrim, N. Ireland BT41 1QS, United Kingdom

Austria

Hereby, Schrader Electronics Ltd. declares that the radio equipment type BC5A4 is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: http://www.tpmseuroshop.com/

documents/

declaration_conformities

Greece

Hereby, Schrader Electronics Ltd. declares that the radio equipment type BC5A4 is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: http://www.tpmseuroshop.com/documents/declaration_conformities

Italy

Certification Tire Pressure Control (TPC)

FCC ID: MRXBC54MA4 IC: 2546A-BC54MA4

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.

FCC ID: MRXBC5A4 IC: 2546A-BC5A4

WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.

Declaration of Conformity

Radio equipment TFT instrument cluster Model name: ICC10in

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period

Technical information

The ICC10in can operate in one of two operating modes:

1. Normal mode, with Bluetooth and WLAN on, and
2. Radio off mode (only available during vehicle manufacturing).

BT operating frq. Range:

2402 - 2480 MHz

BT version: 4.2 (no BTLE)

BT output power:

< +4 dBm (internal antenna)

WLAN operating frq. Range:

2402 - 2472 MHz

WLAN standards:

IEEE 802.11 b/g/n

WLAN output power:

< +14 dBm (internal antenna)

Manufacturer and Address

Manufacturer:

Robert Bosch GmbH

Adress:

Hereby, Robert Bosch GmbH declares that the radio equipment type ICC10in is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://cert.bosch-carmultimedia.net

Italy

Hereby, Robert Bosch GmbH declares that the radio equipment type ICC10in is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://cert.bosch-carmultimedia.net

Declaration of Conformity

Radio equipment TFT instrument cluster

For all Countries without EU

Model name: ICC10in

Technical information

The ICC10in can operate in one of two operating modes:

1. Normal mode, with Bluetooth and WLAN on, and
2. Radio off mode (only available during vehicle manufacturing).

BT operating frq. Range:

2402 - 2480 MHz

BT version: 4.2 (no BTLE)

BT output power:

< +4 dBm (internal antenna)

WLAN operating frq. Range:

2402 - 2472 MHz

WLAN standards:

IEEE 802.11 b/g/n

WLAN output power:

< +14 dBm (internal antenna)

Manufacturer and Address

Manufacturer:

Robert Bosch GmbH

Adress:

(This telecommunication equipments is in compliance with NTC requirements)

Argentinia

RAMATEL

Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Radiofrequency radiation exposure Information: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications made to this equipment not expressly approved by Robert Bosch GmbH may void the FCC authorization to operate this equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Radiofrequency radiation exposure Information: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Japan

This device is granted pursuant to the Japanese Radio Law (電波法) and the Japanese

Telecommunications Business Law (電気通信事業法)

This device should not be modified (otherwise the granted designation number will become invalid)

本製品の改造は禁止されています。

(適合証明番号などが無効となります。)

201-200559

20 0138 201

Korea

Equipment Name: BMW A-Kombi

Basic model number: ICC10in

Manufacturer/Country of Origin:

Robert Bosch GmbH/포르투갈

Zertifikatsnummer:

R-R-BO2-ICC10in

Serbia

ID: И011 20

Mexico

Declaration of Conformity

Radio equipment intelligent emergency call

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period

Technical information

Antenna internal: Frequency Band: 880 MHz - 915 MHz Radiated Power [TRP]: < 22 dBm Not acessable by user: Frequency Band: 1710 MHz - 1785 MHz Radiated Power [TRP]: < 26 dBm Frequency Band: 1920 MHz - 1980 MHz Radiated Power [TRP]: < 22 dBm Frequency Band: 880 MHz - 915 MHz Radiated Power [TRP]: < 23 dBm

Manufacturer and Address

Manufacturer: Robert Bosch Car Multimedia GmbH Adress: Robert Bosch Str. 200, 31139 Hildesheim, GERMANY

Austria

Hereby, Robert Bosch Car Multimedia GmbH declares that the radio equipment type TPM E-CALL EU is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: http://cert.bosch-carmultimedia.net

Greece

Hereby, Robert Bosch Car Multimedia GmbH declares that the radio equipment type TPM E-CALL EU is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: http://cert.bosch-carmultimedia.net

Italy

Declaration of Conformity

Radio equipment anti-theft alarm (DWA)

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period

Technical information

Frequency Band: 433.05-434.79 MHz Output Power: 10 mW e.r.p.

Manufacturer and Address

Manufacturer: Meta System S.p.A. Adress: Via Galimberti 5 42124 Reggio Emilia - Italy

Austria

Hereby, Meta System S.p.A. declares that the radio equipment type TXBMWMR is in compliance with Directive 2014/53/8 The full text of the EU declaration of conformity is available at the following internet address: https://docs.metasystem.it/

Greece

Hereby, Meta System S.p.A. declares that the radio equipment type TXBMWMR is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://docs.metasystem.it/

Italy

Declaration of Conformity

Mid Range Radar MRRe14FCR

Simplified EU Declaration of Conformity under RE-D (2014/53/EU).

Technical information

Frequenzy band: 76 - 77 GHz Nominal radiated power: e.i.r.p. (peak detector): 32 dBm Nominal radiated power: e.i.r.p. (RMS detector): 27 dBm

Manufacturer and Address

Hereby, Robert Bosch GmbH declares that the radio equipment type MRRe14FCR is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://eudoc.bosch.com

Italy

Hereby, Robert Bosch GmbH declares that the radio equipment type MRRe14FCR is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://eudoc.bosch.com

Declaration of Conformity

Mid Range Radar

For all Countries without EU

Model name: MRRe14FCR

Technical information

Frequenzy band: 76 - 77 GHz Nominal radiated power: e.i.r.p. (peak detector): 32 dBm Nominal radiated power: e.i.r.p. (RMS detector): 27 dBm

Manufacturer and Address

Manufacturer: Robert Bosch GmbH Address: Robert-Bosch-Platz 1, 70839 Gerlingen, GERMANY

Type Approved No. ESD-1716172C

IFETEL: RCPBOMR17-0598

TRC No. TRC/LPD/2017/254

CIDF15000490

Complies with IMDA Standards DB03227

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Radiofrequency radiation exposure Information:

This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications made to this equipment not expressly approved by Robert Bosch GmbH may void the FCC authorization to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Radiofrequency radiation exposure Information:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of

20 cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Japan

Translation: This equipment contains specified radio equipment that has been certified to the technical regulation conformity certification under the Radio Law.

Translation: This radio device should not be modified (otherwise the granted designation number will become invalid)

Mexico

HKCA 1035: automotive radar: radio equipment exempted from licensing!

South Korea

[Class B Equipment]

Translation: This equipment has been approved under EMC Registration as a Class B device (for domestic use) and can be used in both residential and commercial areas.

[RF Warnings]

Translation: This radio equipment has potential for interference during operation.

Taiwan, Republic of

注意!

Declaration of Conformity

Radio equipment audio system

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period

Austria

Hereby, ALPS ALPINE CO., LTD. declares that the radio equipment type MCR001 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.alpine.com/e/research/doc/

Italy

Hereby, ALPS ALPINE CO., LTD. declares that the radio equipment type MCR001 is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: http://www.alpine.com/e/research/doc/

Declaration of Conformity

Radio equipment Wireless charging device

Simplified EU Declaration of Conformity acc. Radio Equipment Directive 2014/53/EU after 12.06.2016 and during transition period.

Technical information

Wireless chraging operates in the frequency range from 110 kHz to 115 kHz with a maximum power of 6 W.

Manufacturer and Address

Manufacturer: Bury Sp. z o.o. Address: ul. Wojska Polskiego 4, 39-300 Mielec, Poland

Austria

Hereby, Bury Sp. z o.o. declares that the radio equipment type WCA Motorrad-Ladestaufach is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.bury.com/documents/02-2020_0854_059_BMW_WCA_Motorrad.pdf

Italy

Hereby, Bury Sp. z o.o. declares that the radio equipment type WCA Motorrad-Ladestaufach is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.bury.com/documents/02-2020_0854_059_BMW_WCA_Motorrad.pdf

342 SEZNAM HESEL

A

ABS

Autodiagnostika, 154