Floor One Switch S6 Stretch - Vacuum Cleaner TINECO - Free user manual and instructions

USER MANUAL Floor One Switch S6 Stretch TINECO

Smart Cordless Floor Washer

Instruction Manual

Manual De Uso

Mode D'emploi

*Actual product may differ from illustration.

A

16

17

23
18

24
19

25
20

21

26

22

26

B-1 B

C-1 C

Stop Working Start Again

C-4 C

C-7 C

C-9 C

C-12 C

C-14

①

②

(3)

D-1 D

D-4

①

③

⑤

D-5 D

D-7 D

D-10

D-12

D-14
Uninstall Install

D-16 B

CONTENTS

Important Safety Instructions 7

Specifications 10

Overview 11

Assembly 11

Operation 12

Maintenance 15

Troubleshooting 16

Warranty 17

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS Household use only.

When using an electrical appliance, basic precautions should always be followed, including the following:
- READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE). Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

WARNING - To reduce the risk of fire, electric shock, or injury:

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance shall not be performed by children without supervision.

2. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction.

1. Use only indoors, on non-carpeted floor surfaces such as vinyl, tile, sealed wood, etc. Be careful not to run over loose objects or edges of area rugs. Stalling the brush may result in premature belt failure.
2. Do not allow to be used as a toy. Close attention is necessary when used by or near children, pets or plants.
3. Use only as described in this manual. Use only manufacturer's recommended accessories.
4. Do not use with a damaged cord or plug. If appliance has been dropped, damaged, left outdoors, dropped into water, or is not working as it should, return it to a service center.
5. Do not handle charger, including charger plug, and charger terminals with wet hands.
6. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
7. Keep hair, loose clothing, fingers, and all parts of your body away from openings and moving parts.
8. Use extra care when cleaning on stairs.
9. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
10. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
11. Do not use without filter.
12. Prevent unintentional activation. Ensure the switch is in the off-position before picking up or carrying the appliance. Carrying the appliance with your finger on the switch or energizing appliance that have the switch on invites accidents.

13. Always switch off the appliance before making any adjustments, changing accessories, or storing the appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.

14. Charging only with the charging dock specified by Tineco. A charging dock that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

15. Use appliances only with specifically designated Tineco battery packs. Use of any other battery packs may create a risk of injury and fire.
16. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid comes into eye contact, seek medical help. Liquid ejected from the battery may cause irritation or burns.
17. Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
18. Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 266^ (130^) may cause an explosion.
19. Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
20. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
21. This appliance contains battery cells that are non-replaceable. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.
22. Always turn off this appliance before connecting or disconnecting the motorized nozzle.
23. Do not charge or store the appliance outdoors or inside the car. Only charge,

store or use the battery in a dry indoor area where the temperature is higher than 39.2^ (4^) but lower than 104^ (40^) . The charger is for indoor use only.

1. Do not use to pick up ultrafine particles, such as lime, cement, sawdust, gypsum powder, or ashes.
2. Do not use to pick up sharp objects, such as metallic nails, pieces of glass, metal paper clips, or pins.
3. Do not use to pick up hazardous material and chemicals, such as solvent, drain cleaner, strong acids, or strong alkali.
4. Stop using immediately if the appliance is overheating, making unusual noises, producing unusual odors, performing low suction, or leaks electricity.
5. Turn cleaner OFF and disconnect from electrical outlet for long-term storage.
6. Always clean the Dirty Water Tank after each use to avoid potential blockage, which may lead to low suction power, motor overheating, or reduce the service life of the appliance.
7. Store appropriately indoors in a dry place after use.
8. Do not place or submerge appliance in standing water or try to clean flooded areas.
9. All data and technical instructions of this manual are based on results from lab tests of Tineco or designated third parties. The company reserves all rights for final explanations.
10. The plug must be removed from the socket-outlet before cleaning or maintaining the appliance.
11. A hazard may occur if the appliance runs over the supply cord.
12. Do not use the appliance when the water depth is more than 5mm above the surface.
13. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
14. When battery pack is not in use, keep it away from metal objects such as paper

clips, coins, keys, nails, screws or other small metal objects that could create a connection between the battery terminals. Short-circuiting the battery terminals may result in burns or a fire.
40. To reduce the risk of fire and electric shock - Use only Tineco cleaning products intended for use with this machine.

Range of Usage

1. The cordless hard floor cleaner is to be used on indoor hard floors, such as vinyl, tile, sealed wood, etc. Use on a rough surface may not get the best performance.
2. Keep your appliance away from heat sources, such as fireplace or heater, to avoid casing deformation.
3. Do not use to pick up flammable or combustible liquids, ultrafine particles, sharp objects, hazardous material, chemicals or anything that is burning or smoking, as described above.

About Cleaning Solution

1. A large amount of cleaning solution entering into the motor may cause damage to the appliance.
2. Add solution as instructed in the Operation section. We recommend using the provided cleaning solution. Do not use the product with acidic, alkaline solution, or any substances harmful to the environment.
3. Keep out of the reach of children. Avoid contact with eyes and skin, otherwise, rinse thoroughly with water. If irritation persist, seek medical advice. If product is swallowed seek medical advice.
4. Dirty water and solution disposal should comply with local environmental regulations.

About the Appliance

1. Do not modify or attempt to repair the appliance except as indicated in the

instructions for operating and cleaning.

1. The appliance is only to be used with the power supply provided. The plug must be removed from the socketoutlet before cleaning or appliance maintenance.
2. Use extra care when cleaning on stairs.
3. Ensure that the Power Switch is in the OFF-position before picking up or carrying the appliance. Do not lay flat or lean the appliance so as to prevent dirty water from entering into the motor.
4. To avoid being tripped accidentally, please put away the appliance on the charging base.
5. Always install the Dirty Water Tank and Clean Water Tank properly before use.
6. Do not allow the appliance or charging dock to get wet to avoid risk of fire or injury caused by a short circuit.
7. WARNING: For the purposes of charging the battery, only use the detachable power supply provided with this appliance.
8. Use only with power supply. This appliance contains batteries that are non-replaceable.

FCC Supplier's Declaration of Conformity

TINECO / FLOOR ONE SWITCH S6 SERIES This appliance complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This appliance may not cause harmful interference, and (2) this appliance must accept any interference received, including interference that may cause undesired operation.

TINECO INTELLIGENT, INC.

1700 WESTLAKE AVENUE N., SUITE 200, SEATTLE, WA, 98109, USA
WWW.TINECO.COM

1-855-292-8864

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital appliance, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Note

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment, such modifications could

void the user's authority to operate this equipment.

IC Note

This appliance contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This appliance may not cause interference.
(2) This appliance must accept any interference, including interference that may cause undesired operation of the appliance.

• This Class B digital apparatus complies with Canadian ICES-003.
• This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

SPECIFICATIONS

Product	FLOOR ONE SWITCH S6 SERIES
Voltage 21.6V	=4000mAh Lion
Rated Power 230W
Running Time	Floor Washer: ~35 mins / Hand Vac: ~65 mins
Charging Time 4~5 hrs
Water Flow Rate	20~100ml/min
CWT Capacity ~0.5L
DWT Capacity ~0.45L
Waterproof IPX4
Drying charging dock
Input (drying) 120V~60Hz 3.8A
Input (charging) 120V~60Hz 0.5A
Output 26V	=1A

Disposal

• The battery contains materials that are harmful to the environment and must be removed from the appliance before it is discarded.
• When removing the battery, the appliance must be powered off.
• Batteries, accessories and packaging should be sorted for environmental friendly recycling. Do not put them into fire, water or soil. Do not dispose of batteries and chargers into household waste!
• If battery leakage contacts skin or clothing, immediately flush with water to avoid irritation and seek medical help.

OVERVIEW

Note:

Accessories may vary among markets. If you require more accessories, please go to www.tineco.com or store.tineco.com.

1 Self-cleaning Button
2 Mode Switch
3 Power On/Off
4 Digital Display
5 Main Body
6 Dirty Water Tank Release
7 Dirty Water Tank Handle
8 Dirty Water Tank (DWT)
9 Brush Roller Cover
10 Tube
11 Wifi/Mute/language Switch
12 Clean Water Tank Release
13 Clean Water Tank Handle

14 Clean Water Tank (CWT)
15 Brush Roller
16 Cleaning Tool
17 Dry Filter
18 Deodorizing & Cleaning Solution
19 Zero-Tangle Power Brush
20 Transparent Tray
21 Drying & Charging Dock
22 Vacuum Dock
23 Mini Power Brush
24 2-in-1 Dusting Brush Crevice Tool
25 Dustbin
26 Handle Tube
27 Dirt Monitoring Loop (Blue to red according to the dirt amount)
28WiFi Indicator
29 AUTO Mode
30 DWT Full
31 MAX Mode
32 Floor Washer
33 CWT Empty
34 Brush Roller Tangled
35 Hand Vac
36 MAX Mode in Hand Vac
37 Drying Brush Roller Indicator
38 ECO Mode in Hand Vac
39 Battery Indicator
40 Self-cleaning Icon

Fig.A

ASSEMBLY

How to Assemble/Disassemble Note:

For water tank and brush assembly, please refer to "Operation" and "Maintenance".

• To assemble, install the main body and handle into the appliance until you hear a click.

Fig.B-1

• In the event that the handle needs to be disassembled, first remove the main body. Press the spring to release the handle with a tool (like a screwdriver) and lift the released handle from the appliance.

Fig.B-2

OPERATION

Preparing for Use

• Before first use, please charge the appliance for 4~5 hours (refer to "Charging Instructions" for details).

• Based on results from Tineco lab tests. Lab temperature 39.2°F (4°C) ~ 104°F (40°C).

• Press the button and the appliance will start in AUTO mode by default. Press it again to turn off the appliance. Switch between AUTO and MAX modes by pressing the button.

Fig.C-1

Tips:

• Solution mode/ Water Only mode:
• Appliance starts with Solution mode by default.
• Power on while the appliance is upright, hold for 3s to switch between the two modes.
• Switch to Water Only mode: LED Loop: Red Blue (use water only)

• Switch to Solution mode: LED Loop: Blue Red (use cleaning solution)

• The appliance will stop working when put upright and start running again when reclined.

• Do not recline more than 142^ to avoid water leakage.

Fig.C-2

1. Place the appliance on the charging dock vertically after use for recharge and storage.

Fig.C-3

Note:

• It is crucial to choose the right mode based on the CWT contents to achieve the highest level of dirt detection efficiency.
• Do not vacuum foamed liquid.

Filling Clean Water Tank

1. Press the Clean Water Tank release button to remove it from the appliance.

Fig.C-4

1. Open the tank cap, and fill with tap water to the Max line. When deep cleaning is necessary, add one bottle cap of solution to the CWT and tightly close the cap.

Fig.C-5

Note:

Only use water under 140^ / 60^ DO NOT USE HOT WATER.

1. Place the tank back into the appliance. You should hear a click if done correctly.

Fig.C-6

Charging Instructions

• To charge the appliance, plug in the drying & charging dock and place the appliance on it.
• To avoid tripping hazards, please place the appliance on the charging dock near a wall during charging.

Fig.C-7

Warning:

• Only charge the appliance with the charger supplied by Tineco.
• During long periods of not being used, the appliance must be charged once every 3 months for optimal performance.
• Store indoors in a dry place. Do not expose the appliance to sunlight or freezing temperatures. Recommended temperature range: 39.2^ (4^) 104^ (40^)

Cleaning Mode Selection

AUTO Mode

• In AUTO mode, the iLoop sensor automatically detects how dirty the floor is and applies the appropriate amount of detergent and suction power.
• A red dirt monitoring loop indicates more dirt is detected, and a blue loop indicates less dirt is detected. This mode automatically provides

the best cleaning solution.

Fig.C-8

MAX Mode

• In AUTO mode, press the button to enter MAX mode.
• In Max mode, the appliance will apply max suction power and will spray water/solution for deeper cleaning.

Fig.C-9

ECO Mode (Hand Vac)

• When the main body is used as a hand vac, the appliance will start in ECO mode by default. In ECO mode, the appliance will apply proper suction power to ensure long battery life.

Fig.C-10

MAX Mode (Hand Vac)

• Press the button to switch to MAX mode while using the hand vac.

Fig.C-11

Note:

Keep sharp objects away from the digital display screen to avoid scratches and scrapes.

Usage of Hand Vac

1. Install the dustbin to the main body properly and it clicks into place.
2. Attach the accessory tool onto the dustbin, it will click into position when correctly fitted.

Fig.C-12

• Insert the drying & charging dock into the vacuum dock as shown. Installation is complete when you hear a click.
• Place the appliance and accessories on the vacuum dock for convenient storage after use.

Fig.C-13

• Press the release button to remove the dustbin.
• Pull out the mesh filter as above and empty the contents.
• Press the HEPA lock button to take out the HEPA and sponge filter, clean both parts with the cleaning tool.

Fig.C-14

Note:

• Clean the dustbin and filters after each use.
• To maintain high performance, wash and dry the sponge filter monthly, replacing it every 6 months. Wash and dry the HEPA filter every 3 months, replacing it every 12 months.
  Air dry completely before reinstalling.

Runtime

• The runtime for the Floor Washer is about 35 minutes.
  The runtime for the Hand Vac is about 65 minutes.
• Estimated runtime data was obtained by Tineco Laboratory.

Charging Time

• A full charge takes approximately 4~5 hours.
  Estimated data was obtained by Tineco Laboratory using ambient temperatures ranging from 39.2^ (4^) to 104^ (40^) .

Indicator

When in Use

Battery level >20% : solid green indicator.

Battery level 10% 20% : solid red battery indicator.

Battery level < 10% : battery indicator blinking red.

Battery level ≤ 10% : battery indicator will be blinking.

Off: no power detected or possible battery malfunction.

Indicator blinking: CWT is empty.

Brush roller is tangled	Please clean the brush roller.
Power is off Powered off
Start charging Charging
Begin self-cleaning cycle	Auto-detecting whether to run self-cleaning cycle, please begin self-cleaning cycle
Battery insufficient for self-cleaning	Battery low, charging
Sufficient battery to start self cleaning	Start self cleaning
Cleaning brush roller C	cleaning brush roller
Cleaning the pipe Cleaning	cleaning the pipe
Self-cleaning stopped	Please empty and clean the Dirty Water Tank.
Self-cleaning complete	Please empty and clean the Dirty Water Tank.
Main body uninstalled during selif-cleaning	Please install the main body

MAINTENANCE

Note:

• For optimal performance and to prevent odors, always clean and dry DWT, floater, filters, brush roller, brush roller cover completely after each use.
• Please make sure each part is installed correctly or the appliance may not work properly.
• After maintenance, place the appliance on the charging dock vertically. Do not expose the appliance to direct sunlight, and store it indoors in a dry place.

Main Body

1. To reduce the risk of injury, switch off before performing maintenance.

Fig.D-1

2.Use a cloth to clean the surface with a neutral detergent. The cloth should be dry to prevent

water from entering the appliance.

Fig.D-2

1. Clean the dirt sensor with a damp cloth or the cleaning tool.

Fig.D-3

Dirty Water Tank

• When dirty water reaches the Max line, the appliance will stop working and show a reminder on the display and play a voice prompt.
• Pull up the tank lid to empty the DWT. Throw the debris on the waste separator into the trash.Use the cleaning tool to remove remaining debris. Rinse the inside of the DWT and place back into the appliance. separate hair and debris from dirty water.

Fig.D-4

Dry Filter & Waste Separator

Grasp recessed area on each side of the dry filter and pull upward. Rinse under running water and must be completely dry before recombining with the lid of the DWT.

• A spare dry filter is provided with your appliance for convenient replacement.

The waste separator can be removed and rinsed under the running water.

The function of the waste separator is to separate solid waste.
The appliance can function normally without the waste separator, so users can decide whether to keep it or not.

Fig.D-5

Brush Roller Self-cleaning

1. Place the appliance on the charging dock after use, the sensor will auto-detect the level of dirt.
   2.When you hear the voice prompt "please begin self-cleaning cycle", press the selfcleaning button and begin the process.
   3.Once complete, you will hear the voice prompt "self-cleaning completed, please clean the Dirty Water Tank." At this point, the appliance will begin charging.

Fig.D-6

Note:

• Ensure the charging dock is plugged in and the battery level >20% .
• Before self-cleaning cycle, please clean the DWT and ensure the water level in the CWT>40%.

Brush Roller Cover

1. Squeeze latches on the cover and pull upward to remove.

Fig.D-7

2.Rinse with water.

Fig.D-8

3.When replacing, always latch the brush cover into place to avoid leakage.

Fig.D-9

Brush Roller

1. Remove the brush roller by grabbing the brush roller tab and pulling out.

Fig.D-10

2.Use the cleaning tool to remove the hair and debris wrapped around the roller and rinse the roller with water, and allow it to dry completely before reinstalling.

Fig.D-11

1. Remove hair and debris from the brush roller chamber and the opening with a tissue or a damp cloth.

Fig.D-12

1. Replace the brush roller by inserting the brush roller end into the right side of the holder, then attach the roller tab to the magnetic buckle on the left side to lock into place.

Fig.D-13

Brush Roller Replacement

5.Pull up the roller handle to remove it. Once removed, install the handle into the new brush roller. When uninstalling, do not directly pull on the pull ring of the brush roller.

Fig.D-14

Transparent Tray

1. Move the lock latch to the right, then lift the transparent tray upwards to remove it.

Fig.D-15

1. Clean with water or a towel, and thoroughly dry before reinstalling.

Fig.D-16

Note:

• A spare brush roller is provided with your appliance for convenient replacement.
• To maintain optimal performance, replace the brush roller every 6 months.

SCAN THE QR CODE BELOW TO GET PRODUCT CARE VIDEOS.

TROUBLESHOOTING

Problem Solution
The appliance does not turn on	Restart after cooling down
	Charge the appliance
Weak suction	Install the dry filter or clean and allow it to dry completely
Brush roller tangled indicator blinking Voice prompt: Please clean the brush roller	Remove blockages
WiFi indicator is off	Follow the in-app guide to connect to WiFi
CWT empty indicator blinking Voice prompt: Clean Water Tank empty, please refill water and cleaning solution	Refill CWT
DWT full indicator blinkingVoice prompt:Please clean Dirty Water Tank	Empty the dirty water and then reinstall the DWT
All lights off in operation	Cool the appliance down and restart
Battery indicator blinkingVoice prompt:Low battery, please charge	Charge the appliance, or restart
Self-cleaning icon blinking	Start self-cleaning
All indicators blinking together	Contact Customer Service
Drying malfunction	1. Check if the plug is properly inserted or if the socket has power2. Clean the brush roller3. Check if there are any objects or water at the bottom of the tray that block the air inlet
The transparent tray falls off	To install the transparent tray, press the front end of the transparent tray into place, then press the rear end downwards

Note:

If the above troubleshooting guide fails to provide a solution, please visit our website www.tineco.com for further support.

WARRANTY

2-YEAR LIMITED WARRANTY

• Only applies to purchases made from authorized retailers of Tineco.
• Is subject to the adherence of the requirements outlined in this instruction manual, and is subject to further conditions outlined below.
• This warranty is governed by and construed under the laws of the country in which the purchase took place. We provide 2-year warranty or a warranty period as stipulated by applicable local law, whichever is longer.

WHAT IS COVERED?

• Your Tineco appliance has a 2-year warranty against original defects in material and workmanship, when used for private household purposes in accordance with the Tineco Instruction Manual. Motorized accessories and battery bought separately come with a 1-year warranty.
• This warranty provides, at no extra cost to you, all labor and parts necessary to ensure your appliance is in proper operating condition during the warranty period.
• This warranty will only be valid if the appliance is used in the country in which it was sold.

WHAT IS NOT COVERED?

Tineco shall not be liable for costs, damages or repairs incurred as a result of:

• Appliances purchased from an unauthorized dealer.
• Careless operation or handling, misuse, abuse and/or lack of maintenance or use not in accordance with the Tineco Instruction Manual.
• Use of the appliance other than for normal domestic purposes, e.g. for commercial or rental purposes.
• Use of parts not in accordance with the Tineco Instruction Manual.
• Use of parts and accessories other than those produced or recommended by Tineco.
• External factors unrelated to product quality and use, such as weather, modifications,

accidents, electrical outages, power surges or acts of God.

• Repairs or alterations carried out by unauthorized parties or agents.

• Failing to clear blockage and other hazardous material from the appliance.

• Normal wear and tear, including normal wearing parts, such as clear bin, belt, filter, HEPA, brush bar, and power cord (or where external damage or abuse is diagnosed), carpet or floor damage due to use not in accordance with manufacturer's instructions or failure to turn the brush bar off when necessary.

• Reduction in battery discharge time due to battery age or use.

WARRANTY LIMITATIONS

• Any implied warranties relating to your appliance including but not limited to warranty of merchantability or warranty of fitness for a particular purpose, are limited to the duration of this warranty.
• Warranty coverage applies to the original owner and to the original battery only and is not transferable.
• This limited warranty gives you specific legal rights. You may also have other rights which vary by region.
• Manufacturer's warranties may not apply in all cases, depending on factors such as use of the product, where the product was purchased, or who you purchased the product from. Please review the warranty carefully, and contact the manufacturer if you have any questions.

WARRANTY SERVICE

Register:

• We highly recommend that upon purchase, you register your appliance by logging into our official website (www.tineco.com) or scanning the QR code to enjoy more exclusive benefits. To register, please enter the whole serial number (found on the back of the appliance).

Fig.E-1

• Failure to register your product won't diminish your warranty rights.

How to Claim:

• Please retain your proof of purchase. To make a claim under our Limited Warranty, you need to provide your serial number and the original purchase receipt with the purchase date and order number on it.
• All work will be carried out by Tineco or its authorized agency.
• Any replaced defective parts will become the property of Tineco.
• Service under this warranty will not extend the period of this warranty.

Contact our Customer Service Hotline: [phone] or Visit Tineco website www.tineco.com for expert customer service.

CONTENIDO