YD-27A - Trash can Vevor - Free user manual and instructions

USER MANUAL YD-27A Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

COMMERCIAL SMOKING RECEPTACLES USER MANUAL

YD-27A

YD-27B

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to co all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually Saving Half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

COMMERCIAL SMOKING RECEPTACLES

MODEL:YD-27A YD-27B

Line drawing of a vertical utility pole with a base and two windows, no text or symbols present

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate

www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of o user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you ag there are any technology or software updates on our product.

WARNING:

Read this material before using this product. Failure to do so can result in serious injury.

Assembly precautions

1. Assemble only according to these instructions. Improper assembly c create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or when under the influence of alcohol, or medication.
6. The product capabilities apply to properly and completely assembled products only.
7. Assemble on a flat, level, hard and smooth surface capable of sa supporting the Commercial Smoking Receptacles.
8. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unw and separate all parts in a clean work area.

Use precautions

1. DO NOT SIT OR STAND ON THIS ITEM.
2. This product is not a toy. Do not allow children to play with or item.
3. Do not exceed specified weight capacities.
4. Use only on a flat, level, hard, and smooth surface that can safe support a fully loaded Commercial Smoking Receptacles.
5. Use as intended only.
6. Inspect before every use; do not use if parts are loose or damage

SAVE THIS MANUAL

Technical diagram of a mechanical device with numbered components and exploded view, including base, clamps, and wrench.

1	Main Body Of Ash Colu		4	Key *1
2	Inner Barrel *1		5	19mm Open End Wrench
3	M10*120 Expansion Bolt *2

STEP 1: Select The Installation Position And Drilling

Note: Please ensure that the direction of the door opening in the installation position is free from obstacles.

1. Set the drilling position on the hard ground, the center distance =50mm (as shown below).
2. With a diameter of 12mm drill bit in the selected position, the drilling depth is not less than 60mm.

210mm 210mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

STEP 2: Install

1. Fully open the door, align the base holes with the ground, an insert M10*120mm expansion bolts into the holes in sequence A B.
2. Use the open end wrench to lock the bolt

Technical diagram showing a hammer and screwdriver working on a mechanical assembly with labeled parts A and B

STEP 3: Open Limit

1. Use an open end wrench to push the limiting device ⑥ on panel to both sides.
2. The limit can maintain the opening Angle of the door panel about 20, which is easy to remove the inner barrel and avoid the panel falling directly to the ground.

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

Model	YD-27A	YD-27B
Colour	Silver	Black
Product Size	210*210*1080mm

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODÈLE : YD-27A YD-27B

Line drawing of a vertical utility pole with two square windows and a handle (no text or symbols)

BESOIN D'AIDE? CONTACTEZ-NOUS!

Technical diagram of a street lamp with labeled components including base, panel, and switch parts

210mm 210mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

ÉTAPE 2 : Installer

Technical diagram showing a hammer and screwdriver working on a mechanical assembly with labeled parts A and B

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

MODELL: YD-27A YD-27B

Line drawing of a vertical utility pole with a base and two windows (no text or symbols)

www.vevor.com/support

Technical diagram of a street lamp with labeled components including base, panel, and switch parts

210mm 210mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

SCHRITT 2: Installieren

Technical diagram showing a hammer and screwdriver working on a mechanical assembly with labeled parts A and B

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODELLO:YD-27A YD-27B

Line drawing of a tall industrial trash bin with a side-mounted outlet (no text or symbols)

Technical diagram of a street lamp with labeled components including base, panel, and switch parts

210mm 210mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

FASE 2: Installare

Technical diagram showing a hammer and wrench working on a mechanical assembly with labeled parts A and B

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

Importato in AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Importato negli USA: Sanven Technology Ltd. Suite 250, 9166 Anahei Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODELO: YD-27A YD-27B

Line drawing of a vertical utility pole with two square windows and a handle (no text or symbols)

Technical diagram of a street lamp with labeled components including base, panel, and switch parts

210mm 210mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

PASO 2: Instalar

Technical diagram showing a hammer and screwdriver working on a mechanical assembly with labeled parts A and B

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODELE:YD-27A YD-27B

Line drawing of a vertical utility pole with a base and two windows (no text or symbols)

POTRZEBUJESZ POMOCY? SKONTAKTUJ SIĘ Z NAMI!

www.vevor.com/support

Technical diagram of a street lamp with labeled components including base, switch, and power tool

210mm 210mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

KROK 2: Zainstaluj

Technical diagram showing a hammer and screwdriver working on a mechanical assembly with labeled parts A and B

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

STREETEASTWOOD NSW 2122 Australia

Importowane do USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

Technisch Ondersteuning en E-garantiecertificaat www.vevor.com/support

COMMERCIËLE ROOKCONTAINERS

MODEL: YD-27A YD-27B

Line drawing of a vertical utility pole with two square windows and a handle (no text or symbols)

HULP NODIG? NEEM CONTACT MET ONS OP!

www.vevor.com/support

Technical diagram of a street lamp with labeled components including base, panel, and switch parts

210mm 210mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

STAP 2: Installeren

Technical diagram showing a hammer and wrench working on a mechanical assembly with labeled parts A and B

STAP 3: Open limiet

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

MODELL: YD-27A YD-27B

Line drawing of a vertical utility pole with two square windows and a handle (no text or symbols)

BEHÖVER HJÄLP? KONTAKTA OSS!

Technical diagram of a street lamp with labeled components including base, panel, and switch parts

210 mm 210 mm The arrow indicates the direction of the door The center distance between the two holes is 50mm

Base and mounting hole spacing dimensions

STEG 2: Installera

Technical diagram showing a hammer and screwdriver working on a mechanical assembly with labeled parts A and B

STEG 3: Öppen gräns

⑥ Limiting Device 20°

INSTRUCTIONS FOR USE

First,:Smoke Out, Input

1. Align the burning cigarette with tr
   ① position and rub until the end of cigarette is extinguished.
2. Put the extinguished cigarette or burned cigarette butt into the collected
   from the② position.

Second: Opening/Closing of the Lock Insert the key into the keyhole and it 90 degrees to the left or right to or close the lock.

Thirdly: Clean Up Soot And Cigarette Butts

After unlocking, hold the plastic hand under the hand and pull the door in direction of the arrow.

You can remove the inner liner to (the soot and cigarette butts.

Close the door after cleaning and re step 2 to lock the door.

① Porous smoke extinguishing plate

① ② Flue hole 90° 90°

e door.

Technical line drawing of a vertical pole-mounted structure with a circular arrow indicating rotation (no text or symbols)

PRODUCT PARAMETER

Modell	YD-27 A	YD-27B
Färg	Silver	Svart
Produktstorlek	210*210*1080 mm

Tillverkare: Shanghaimuxinmuyeyouxiangongsi

Adress: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Importerad till AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOI NSW 2122 Australien

Importerad till USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support