08658 - Iron Cleanmaxx - Free user manual and instructions

USER MANUAL 08658 Cleanmaxx

Filling the Water Tank 15

Assembly 15

Use 16

Tips 18

Cleaning and Storage 18

Troubleshooting 18

Technical Data 19

Disposal 19

ITEMS SUPPLIED

1 x motor unit

1 x telescopic rod with drip guard (long)

1 x rod with drip guard (short)

1 x hanger

1 x Y tube

2 x rod

1 x balloon (shirts, blouses)

1 x balloon (trousers)

5 x clamps with integrated weight

1 x measuring cup

1 x operating instructions

Check the items supplied for completeness and transport damage. If you find any damage to the device, the accessories or the connecting cable, do not (!) use them, but contact our customer service department.

Remove any possible films, stickers or transport protection from the device. Never remove the rating plate and any possible warnings!

DEVICE OVERVIEW

(Picture A + B)

1 Hanger
2 Telescopic rod
3 Fan
4 Water tank cover
5 Water tank (in housing)
6 Motor unit
7 Ventilation slots
8 Control panel
9 Mounting flange
10 Drip guard (premounted on the telescopic rod)
11 Clip (for adjusting the height)
12 Collar section
13 Rods
14 Y tube

(Picture C) – Control Panel

15 Operating time display (1 bar = 1 minute)
16 ▲ Increase the operating time
17 Pressing programme with steaming (for dry textiles)
18 + Start / pause
19 ▼ Decrease the operating time
20 Pressing programme without steaming (for damp textiles)

EN

Dear Customer,

We are delighted that you have chosen this steam presser.

Before using the device for the first time, please read through the operating instructions carefully and keep them for future reference. If the device is given to someone else, it should always be accompanied by these operating instructions. They are an integral part of the device.

The manufacturer and importer do not accept any liability if the information in these operating instructions is not complied with.

If you have any questions about the device and about spare parts / accessories, contact the customer service department via our website: www.ds-group.de/kundenservice

SYMBOLS

Danger symbols: These symbols indicate possible dangers. Read the associated safety notices carefully and follow them.

Caution: hot surfaces!

This device works with hot steam!

Read instruction manual before use!

Supplementary information

SIGNAL WORDS

Signal words indicate hazards if the associated notices are not followed.

WARNING – medium risk, may result in serious injury or death

CAUTION – low risk, may result in minor or moderate injury

NOTE – may result in risk of damage to material

INTENDED USE

• This device is intended to be used to dry, steam and press textiles, for example blouses, shirts and trousers. Delicate textiles such as wool or similar fabrics must not be pressed on the presser. Always follow the care labels for the textiles!
• The device is intended for machine-spun or dry, washed laundry.

WARNING: This device is intended only for drying textiles washed in water.

• The device is for personal use only and is not intended for commercial applications.
• The device should only be used as described in the operating instructions. Any other use is deemed to be improper.
• The warranty does not cover faults caused by incorrect handling, damage or attempted repairs. The same applies to normal wear and tear.

SAFETY NOTICES

Warning: Note all safety notices, instructions, illustrations and technical data provided with this device. Failure to follow the safety notices and instructions may result in electric shock, fire and / or injuries.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or a lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
■ Children shallo not play with the appliance.
■ Cleaning and user maintenance shall not be made by children without supervision.
- Keep children younger than 8 years of age and animals away from the device and the connecting cable.

CAUTION: Hot surfaces! The motor unit / rods will become hot during use. You should therefore not touch it during or shortly after use.

CAUTION: hot steam! This device works with hot steam! Operate the device with caution.

■ The device must always be switched off and disconnected from the mains power when it is not being used, before assembling, disassembling, filling or emptying the water tank or cleaning the device.

- Do not make any modifications to the device. If the connecting cable of the device is damaged, it must be replaced by the manufacturer, its customer service department or a similarly qualified person (e.g. a specialist workshop) in order to avoid any hazards.

• Allow the device to cool down completely before the water tank is emptied and / or the device is cleaned and stored away.
• It is essential to follow the instructions in the “Cleaning and Storage” chapter.

EN

WARNING – Danger of Electric Shock

■ Use the device only in closed rooms.
■ Do not use the device in rooms with high humidity.
■ Never immerse the device and the connecting cable in water or other liquids and ensure that they cannot fall into water or become wet.
■ Should the device fall into water, switch off the power supply immediately. Do not attempt to pull it out of the water while it is still connected to the mains power!
■ Never touch the device and the connecting cable with wet hands when these components are connected to the mains power.
■ Never exceed the maximum fill level of the water tank to prevent overflowing (Note the MAX marking on the measuring cup and in the water tank!).
■ Steam may rise during operation. For this reason, do not place the device under other electronic devices.

WARNING – Danger of Injury

• Keep the packaging material away from children and animals. There is a danger of suffocation.
  ■ Make sure that the connecting cable does not present a trip hazard. There is a danger of tripping.
  ■ The device must not be moved during use.
  ■ Make sure that the connecting cable is always kept out of the reach of small children and animals. There is a danger of strangulation.

WARNING – Danger of Fire

■ Do not connect the device along with other consumers (with a high wattage) to a multiple socket in order to prevent overloading and a possible short circuit (fire).
■ Do not use the device in conjunction with extension cables.
■ Do not operate the device in the vicinity of combustible material.

NOTICE – Risk of Damage to Material and Property

■ Only connect the device to a plug socket with safety contacts that is properly installed and matches the technical data of the device. The plug socket must also be readily accessible after connection so that the connection to the mains can quickly be isolated.
Before using the device, read the care instructions for the fabric which is to be smoothed. Some fabrics, leather and suede as well as fabrics with flounces, sequins and appliqués must not be steamed!
■ Always switch off the device first before the plug is pulled out of the plug socket.
■ Never cover up the ventilation slots and do not insert any objects into them.
■ Lay the mains cable in such a way that it does not become squashed or bent and does not come into contact with hot surfaces.
■ Switch off the device and pull the mains plug out of the plug socket if an error occurs during operation, when there is a power cut or before a thunderstorm.
■ Never pull or carry the device by the connecting cable. When you pull it out of the plug socket, always pull on the mains plug and never the mains cable!
■ Protect the device from other heat sources, flames, sub-zero temperatures,

persistent moisture, wet conditions and impacts.

■ Use only original accessories from the manufacturer in order to guarantee that there is no interference that may prevent the device from working and to avoid possible damage.

FILLING THE WATER TANK

Please note!

■ Never pour any descaling or cleaning agent or other chemical additives into the water tank. This may destroy the device and safe working is no longer guaranteed.
■ Only ever use distilled water with the device to prevent calcification and damage to the device.
■ Never pour more than 700 ml (two measuring cups filled up to the MAX marking) of water into the water tank.

Water residues in the water tank are attributable to the fact that this device has been tested and do not constitute a defect.

1. Make sure that the device is not connected to the mains power and has cooled down sufficiently if used previously.
2. Fill the measuring cup up to the MAX marking with water.
3. Open the water tank cover (4) by pressing on the cover on the left.
4. Pour the water from the measuring cup into the water tank (5). Here too you should note the MAX marking.

For the best results, we recommend pouring no more than 350 ml into the water tank for each steaming process.

1. Flip the water tank cover back down again.

ASSEMBLY

Presser for blouses and shirts

1. Plug the telescopic rod (2) into the recess on the top of the motor unit (6).

The drip guard (10) must be located above the fan (3). It prevents any water that may drip down from being able to get into the fan.

1. Place the hanger (1) onto the telescopic rod. When you do this, make sure that the slight bend in the hanger points forwards. The hanger must audibly engage on the telescopic rod.
2. Attach the balloon for shirts / blouses (Picture D):

- Pull it over the hanger. When you do this, make sure that the side with the hole line points forwards.

- Pull the small elastic cord at the top over the collar section (12) on the hanger.

- Pull the large elastic cord at the bottom over the mounting flange (9).

The device is disassembled in the reverse order.

Presser for trousers (Picture E)

1. Insert the rod with the drip guard into the recess on the top of the motor unit (6). The drip guard (10) must be located above the fan (3). It prevents any water that may drip down from being able to get into the fan.
2. Fit the Y tube (14) on the rod with the drip guard.
3. Insert the two rods (13) into the Y tube.
4. Attach the balloon for trousers:

- draw it over the two rods.

- draw the elastic over the mounting flange (9).

The device is disassembled in the reverse order.

EN

USE

Please note!

■ Always place the device with sufficient clear space above it and on all sides on a dry, flat, solid, water-resistant and heat-resistant surface.
■ The device must not be left unattended during operation.
■ Be aware that the clamps with integrated weight may likewise become hot during use. Allow them to cool down suitably before they are detached from the item of clothing.
■ Let the device cool down after every pressing process.
It is essential that you follow the care labels for the textiles which are to be dried / smoothed!

For the best results, the device should ideally be used in a room that is as cool as possible. We recommend a maximum room temperature of 25 °C.

Presser for blouses and shirts

1. Set the height you want. To do this, open the clip (11), pull out the telescopic rod (2) and then close the clip again. We recommend pulling the telescopic rod out to its maximum height (Picture F).
2. If the item of clothing is to be steamed, fill the water tank (5) (see the "Filling the Water Tank" chapter).
3. Pull on the balloon (see the "Assembly" chapter).

The balloon should sit immediately below the mounting flange (9) so that it can fully inflate.

1. Pull the garment which is to be pressed over the balloon and the hanger (1) and do up the buttons if necessary (Picture G). Make sure that

2. the collar is fitted over the collar section (12) on the hanger,

3. any button strip is over the hole line on the balloon.
4. the arms of the balloon fit properly in the sleeves of the garment and are not twisted or scrunched up,

5. all buttons on the garment (including on the sleeves) are done up.

6. Spread the clamps along the bottom of the garment (at the front and back in each case on the outsides and in the middle on the button strip at the front) so that it is weighed down and will not go out of shape when the balloon is inflated.

7. Insert the mains plug into an easily accessible plug socket. The device switches on and on the control panel (8) the symbols (20) and (17) light up.
8. Select the programme you want by touching the appropriate symbol on the control panel:

- - pressing programme without steaming (intended for damp textiles)

- - pressing programme with steaming (intended for dry textiles)

On the control panel, the symbol for the programme you want and the arrow symbols (16 + 19) light up. The symbol (18) flashes.

1. Use the arrow symbols to set the operating time you want (max. 30 minutes). 1 bar represents 1 minute of operating time here.

When setting the time for the pressing programme with steaming, please note that the process of steaming the garment takes approx. 7 minutes and only then does the pressing process start. An operating time of approx. 12 – 15 minutes should therefore be set.

EN

1. Touch the Symbol to start the pressing process. It is now permanently lit. The symbol for the set programme flashes.

The lighting of the control panel switches off after approx. 40 seconds.

To reactivate it, touch the middle of the control panel.

1. Once the balloon has inflated, straight-en out the garment and smooth it down again.

The pressing process can be paused at any time by touching the ▶ symbol. When the process is interrupted, the ▶ symbol flashes.

If the operating time for the pressing process is to be adapted, use the ▲ and ▼ symbols to extend or shorten the operating time. Then touch the □ symbol again to continue the pressing process.

If during the pressing programme with steaming the operating time is adapted, this change only affects the pressing process and not the steaming! Example: The operating time is set to 15 minutes. The process is interrupted after 3 minutes and the operating time is extended by 5 minutes. After the process resumes, the steaming still only takes 4 minutes, and not 7.

PLEASE NOTE: After switching to the pressing programme with steaming, the steaming always starts again and lasts 7 minutes!

1. The device stops automatically after the set operating time has elapsed. The control panel goes out and the device switches to stand-by mode.

If the operating time should be ended prematurely, press the

symbol to pause the process and the ▼ symbol until there is no longer any bar lit up on the operating time display (15). The control panel goes out and the device switches to stand-by mode.

1. Remove the garment from the balloon and hanger.
2. Pull the mains plug out of the plug socket and allow the device to cool down completely.

Presser for trousers

1. If you have not yet done so, attach the balloon (2) (see the "Assembly" chapter).

The balloon should sit immediately below the mounting flange so that it can fully inflate (Picture H).

1. Pull the garment which is to be pressed over the balloon and do up the zip or buttons if necessary. Make sure that

   • the legs of the balloon fit properly into the legs of the trousers and are not twisted or scrunched up,
   • all buttons on the garment (including the legs) are done up.

2. Spread the clamps along the bottom of the garment (at the front and back in each case on the outsides) so that it is weighed down and will not go out of shape when the balloon is inflated.

3. Operate the device as described in the "Presser for blouses and shirts" section.
4. Once the balloon has inflated, straight-en out the garment and smooth it down again.
5. Remove the garment from the balloon after the completion of the drying/pressing process.
6. Switch off the main device, unplug it and allow it to cool.

EN

TIPS

• If in the pressing programme without steaming hand-washed or non-machine-spun laundry is to be pressed, allow it to dry first.
• The pressing process without steaming takes around 10 minutes for a spun-dried shirt or trousers. However, the length of time can vary depending on the material and thickness of the material. We recommend that you start with a shorter time and extend it if necessary.
• The pressing process with steaming takes around 15 minutes for a dry shirt or trousers. Here too the time may vary depending on the material and thickness of the material.
• The balloon for shirts and blouses can be enlarged or reduced in size with the zips. For smaller sizes, the zips should be closed. For larger sizes, the zips should be opened on both sides.
• Wide-apart buttons may result in the button strip crimping slightly during pressing. Here it is advisable to smooth down the button strip again by hand immediately after the pressing process.
• In the case of trousers with a very small waist it may not be possible to pull them over the attachment when it has already been fitted. In this case you

proceed as follows:

• push the balloon upwards slightly, to enable access to the rods (13),
• remove one of the two rods from the Y tube once more (14),
• draw the trousers over the two rods,
• now replace the rods in the Y tube and
• draw the balloon over the mounting flange on the main device again.

- After the drying/pressing process any creases need to be ironed out using a normal iron.

CLEANING AND STORAGE

Please note!

- Do not use any caustic or abrasive cleaning agents or cleaning pads for cleaning. These may damage the surface.

• Clean the device and the balloons if necessary with a slightly damp cloth and a little mild detergent if required. Then wipe with a dry cloth.
• Empty the water tank (5) if the device is not going to be used for a long time or before storing it away. To do this, remove the balloon and telescopic rod (2) take the device apart and tilt the motor unit (6) so that the water can escape from the steam outlet openings beneath the mounting flange (9).
• Allow all parts to dry completely before storing them away.
• Store the device in a clean, dry place which is protected from sunlight and is not accessible to children and animals.

TROUBLESHOOTING

If the device does not work properly, check whether you are able to rectify the problem yourself. If the problem cannot be solved with the steps listed, contact the customer service department.

Do not attempt to repair an electrical device yourself!

The control panel does not light up.

▶ Check the fit of the mains plug.
▶ Try another plug socket.
▶ Check the fuse of the mains connection.
▶ Touch the middle of the control panel.

Unusual noises

▶ Free up the ventilation slots.

The device switches off suddenly.

▶ Free up the ventilation slots.
The device has an automatic safety switch-off function. It switches off automatically if it overheats / the water tank is empty. Allow the device to cool down and switch it on again.

• The device has a protective switch that is activated if the device falls over. Set the device up again and switch it back on.
• Set the operating time again.

Odour produced

▶ You might notice a slight odour caused by production residues the first time you use the device. However, this is harmless and will cease as you use the device.

No steam is produced.

The device has not yet reached operating temperature. Depending on how full the water tank is, it may take a few minutes for the water to be hot enough for steam to be produced.

TECHNICAL DATA

Article number: 08658 (white);

14915 (silver / black)

Model number: LGY-03I

Voltage supply: 220 – 240 V \~ 50 Hz

Power: 1800 W

Protection class: I

Type of protection: IPX1

Capacity of water

tank: approx. 700 ml

ID of operating Z 08658_14915 M DS

instructions: V1 0524 as

DISPOSAL

Dispose of the packaging material in an environmentally friendly manner so that it can be recycled.

The adjacent symbol (crossed-out bin underlined) means that used devices should not be disposed of in the domestic waste, but should instead be taken to special collection and return systems.

Owners of used devices from private households can take them free of charge to the collection points of the public waste disposal authorities or the disposal points which are set up by manufacturers and distributors under the Electrical Equipment Act so that they can be disposed of in an environmentally friendly way and valuable raw materials can be recovered. If they are not disposed of properly, toxic ingredients may escape into the environment and cause harm to the health of humans, animals and plants. Businesses which market electrical and electronic devices are also obliged to take back used devices.

Waste prevention makes an even more valuable contribution to protecting the environment. This means if possible, as well as continuing to use or repair, passing it on to another user also represents an ecologically beneficial alternative to disposal.

All rights reserved.

FR

CONTENU

Composition 20

1 x ballon (chemises, blouses)

1 x ballon (pantalons)

5 Watertank (in de behuizing)

6 Motorblok

7 Ventilatiesleuven

8 Bedieningspaneel

9 Bevestigingsrand

WAARSCHUWING - Verwondingsgevaar

WAARSCHUWING – Brandgevaar