Zeus Battery - Lamp BeamZ - Free user manual and instructions

USER MANUAL Zeus Battery BeamZ

150.646_150.648 V1.3

ZEUS

USER MANUAL

INDEX

ENGLISH

SAFETY INSTRUCTIONS....3

UNPACKING INSTRUCTION 4

POWERSUPPLY 4

APP INSTRUCTION 4

CLEANING 5

MAINTENANCE 5

TROUBLE SHOOTING 6

NEDERLANDS

VEILIGHEIDSINSTRUCTIES 7

UITPAKKEN 8

AANSLUITSPANNING 8

APP INSTRUCTIE 8

REINIGEN 9

ONDERHOUD....9

PROBLEMEN OPLOSSEN 10

DEUTSCH

40/80/160 channels 32

SAFETY INSTRUCTIONS

WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with care for future reference. It contains important information about the installation, usage and maintenance of the unit.

• Unpack and check carefully that there is no transportation damage before using the unit
- Please read these instructions carefully and follow the instructions.
- Observe all safety warnings. Never remove safety warnings or other information from the equipment.
- Be sure that no ventilation slots are blocked; otherwise the unit will overheated.

WARNING! Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

• After connecting the unit, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.
• Make sure that the power cord is never crimped or damaged. Check the unit and the power cord from time to time.
- Always disconnect power from the mains, when unit is not used or before cleaning! Only handle the power cord by the plug. Never pull out the plug by tugging the power cord.
• Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

- Do not switch the unit on and off in short intervals.

- Do not connect the unit to a dimmerpack.

• Install the unit in a well ventilated place.

- Never place any material over the lens.

- Never let the sunlight lights directly to the front lens, even when the unit is not working.

• Always allow free air space of at least 50 cm around the unit for ventilation.

• Make sure that the area below the installation place is blocked when rigging, derigging or servicing the unit.

- For mounting height >100 cm, always fix the unit with an appropriate safety-rope. Fix the safety-rope at the correct fixation points only. The safety-rope must never be fixed at the transport handles!

- Never look directly at the light beam. Please note that fast changes in lighting, e.g. flashing light, may trigger epileptic seizures in photosensitive persons or persons with epilepsy.

- This unit is not designed for permanent operation. Consistent operation breaks will ensure that the unit will serve you for a long time without defects.

WARNING! If the power cord of the unit is equipped with an earthing contact, then it must be connected to an outlet with a protective ground. Never deactivate the protective ground of a power cord.

• Make sure that the unit is not exposed to extreme heat or dust.
- Clean the unit using a dry cloth.
- Do not touch the unit bare-handed during its operation (housing becomes very hot). Allow the unit to cool for at least 5 minutes before handling.

- Do not expose this unit to flammable materials, fluids or gases.

- If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

- Never attempt to bypass the thermostatic switch or fuses.

- Do not dismantle or modify the unit.

- For replacement use fuses/bulb of same type and rating only.

• Repairs, servicing and electric connection must be carried out by a qualified technician.

- The ambient temperature must always be between -5^ and +45^ .

- If this unit is operated in any other way, than the one described in this manual, the product may suffer damages and the warranty becomes void.

- Plastic bags must be kept out of reach of children.

- Unit must be installed out of the reach of children. Never leave the unit running unattended.

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing.

If the unit has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your unit. Leave the unit switched off until it has reached room temperature.

POWERSUPPLY

The label on the backside of the unit indicates the mains voltage to which it must be connected. Check that the mains voltage corresponds to this. Any other voltage than the one indicated may cause irreparable damage to the unit. The unit must also be connected directly to the mains voltage and no dimmer or adjustable power supply may be used.

WARNING! Always connect the unit to a protected circuit (circuit breaker or fuse). Make sure the unit has an appropriate electrical ground to avoid the risk of electrocution or fire.

APP INSTRUCTION

STEP 1:

Find [WIFI] and press to tor[ENTER].

STEP 2:

"Led_XXX" displayed on the screen is the WIFI address of the light fixture.

STEP 3:

Scan the above QR code to install [AEB (UAMP)] mobile phone.

STEP 4:

On the phone, find WIFI and search WIFI address, and the words beginning with LED appear. For example, "LED-XXX", click the link.

STEP 5:

Turn on the [AED] inside on the phone and show the link is successful then you can control it.

QR code with central logo containing 'LUBD' text and a rainbow-colored circular design

CLEANING

The buildup of dust, dirt and other airborne particles will reduce the unit's light output. It will also prevent the unit from cooling correctly, and this will reduce the unit's lifetime. The rate of dirt buildup will vary depending on environmental factors such as airborne dust, use of smoke machines, airflow from ventilation systems, etc. The unit's cooling fans will accelerate buildup, and any smoke particles that are present in the atmosphere will increase the tendency for dirt to clog.

To get the best performance and lifetime from the unit, inspect it regularly and clean it as soon as you see signs of dirt buildup.

Assess the operating environment each time you begin to use the unit. In dusty or smoky conditions, inspect the unit after a few hours and check it frequently the unit may attract dirt faster than you expect. Draw up a cleaning schedule that will make sure that dirt is removed before it can build up.

Use the following guidelines:

• Disconnect the unit from power and allow it to cool completely before cleaning.
• Do not use solvents, abrasives or any other aggressive product to clean the unit.
• Vacuum or use low-pressure compressed air to remove dust and loose particles from surfaces and air vents. Prevent the blades of cooling fans from turning before you aim a vacuum or air jet at the fan, or you may spin the fan too fast and damage it.
• Clean glass components by wiping gently with a soft, clean, lint-free cloth moistened with a weak detergent solution. Put the solution on the cloth and not on the surface to be cleaned. Avoid rubbing glass surfaces.
• Dry the unit with a soft, clean, lint-free cloth or low-pressure compressed air before reapplying power.

MAINTENANCE

This unit is virtually maintenance-free, but you should check the unit regularly for mechanical and electrical aspects.

Assess the operating environment and establish an inspection and cleaning schedule that follows the guidelines below:

• Disconnect the unit from the power supply and allow it to cool completely before inspecting and cleaning.
• Check that the screws and bolts used to install the unit are securely tightened and free from corrosion.
• Check the housing, fixing points and installation points, they must not show any signs of deformation, wear or fatigue.
• Check the mechanically moving parts, these must not show any signs of wear or fatigue.
• Check the electrical power and signal cables, they must not show any damage or fatigue.
• Do not use solvents, abrasives or other aggressive products to clean the unit.
• Wipe the unit and clean the glass plate with a soft, clean, lint-free cloth moistened with a weak cleaning solution. Place the solution on the cloth and not on the surface to be cleaned. Avoid rubbing glass surfaces.
  • Dry the unit, connectors and contacts with a soft, clean, lint-free cloth or low-pressure compressed air before re-powering the unit.

TROUBLE SHOOTING

The checklist below may help you troubleshoot in the unlikely event that a problem occurs while using the product:

SYMPTOM	POSSIBLE CAUSE	SUGGESTED ACTION
No response from unit.	No power to unit.Fuse blown or internal fault.	Check that power is turned on.Check cables and connections.Replace mean fuse or contact Beamz support or Beamz authorized service partner. Do not remove base or yoke covers. Do not attempt to replace a fuse or carry out any repairs or service that are not described in this User Manual unless you have both authorization from Beamz support or Beamz authorized service partner.
Unit resets correctly but does not respond (or does not respond correctly) to the controller.	The controller is not connected.Bad DMX-line.DMX-line has no end resistance.Incorrect unit addressing.A unit is defective and is disturbing data transmission on the DMX-line.Pin 2 and 3 are reversed in XLR connection.	Connect controller.Inspect connections and cables. Correct poor connections. Repair or replace damaged cables.Insert DMX terminator plug in DMX output socket of last unit on DMX-line.Check unit address and DMX mode settings.Unplug DMX IN and OUT connectors and connect them directly together to bypass one unit at a time until normal operation is regained.Have defective unit serviced by an authorized technician.Inspect connections and cables. Install a phase-reversing cable between the units or swap pin 2 and 3 in the unit, that behaves erratically.
Error after unit reset.	Effect requires mechanical adjustment.	Check unit's software version and error messages for more information. Contact Beamz support or Beamz authorized service partner.
Light output cuts out intermittently.	Unit too hot.LEDs damaged.The power supply settings do not match local AC voltage and frequency.	Allow unit to cool. Reduce ambient temperature. Ensure free airflow around unit. Clean unit if necessary.Disconnect unit and contact Beamz support or Beamz authorized service partner.Disconnect unit. Check settings and correct if necessary.

VEILIGHEIDSINSTRUCTIES

QR code with central logo containing 'LED' text and rainbow-colored arc design

REINIGEN

QR code with central logo containing 'LED' text and rainbow-colored circular design

REINIGUNG

QR code with central logo containing 'LED' text and rainbow-colored circular design

LIMPIEZA

QR code with a central logo featuring a rainbow-colored 'LED' and white text.

NETTOYAGE

QR code with a central logo containing the letters 'L' and 'B', likely linking to a digital resource or website.

CZYSZCZENIE

CAUTION! The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote control. Otherwise operation of the remote control is not possible.

If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control press the small bar with the groove to the right (1) and at the same time remove the battery support (2). For operation, one 3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of the button cell shows upwards in the support.

1 2

DMX CHANNELS

4A CHANNELS

CHANNEL	VALUE	DESCRIPTION
1	000-255	Total dimming
2	000-010	No function
	011-255	Strobe
3	000-004	No function
	005-255	Color temperature
4	000-255	Tune GM

4B CHANNELS

CHANNEL	VALUE	DESCRIPTION
1	000-255	Total dimming
2	000-010	No function
	011-255	Strobe
3	000-004	No function
	005-255	Tune RGB mixed color
4	000-255	Color saturation

5 CHANNELS

CHANNEL	VALUE	DESCRIPTION
1	000-255	Red dimming
2	000-255	Green dimming
3	000-255	Blue dimming
4	000-255	Cool white dimming
5	000-255	Warm white dimming

6A CHANNELS

CHANNEL	VALUE	DESCRIPTION
1	000-255	Total dimming
2	000-010	No function
	011-255	Strobe
3	000-004	No function
	005-255	RGB mixed color
4	000-255	Color saturation
5	000-004	No function
	005-255	Color temperature
6	000-255	Tune GM

6B CHANNELS

CHANNEL	VALUE	DESCRIPTION
1	000-255	Total dimming
2	000-255	Red dimming
3	000-255	Green dimming
4	000-255	Blue dimming
5	000-255	Cool white dimming
6	000-255	Warm white dimming

7 CHANNELS

CHANNEL	VALUE	DESCRIPTION
1	000-255	Total dimming
2	000-010	No function
	011-255	Strobe
3	000-255	Red dimming
4	000-255	Green dimming
5	000-255	Blue dimming
6	000-255	Cool white dimming
7	000-255	Warm white dimming

12 CHANNELS

CHANNEL		VALUE	DESCRIPTION
1		000-255	Total dimming
2		000-010	No function
		011-255	Strobe
3	000-010		No function
	011-019		Red
	020-028		Green
	029-037		Blue
	038-046		Cool white
	047-055		Warm white
	056-064		Red + green
	065-073		Green + blue
	074-082		Red + blue
	083-091		Red + green
	092-100		Green + blue
	101-109		Red + warm white
	110-118		Red + green
	119-127		Green + blue
	128-136		Red + blue
	137-145		Blue + warm white
	146-154		Warm white + cool white
	155-163		Green + cool white
	164-172		Green + warm white
	173-181		Red + blue + cool white
	182-190		Red + warm white + coolwhite
	191-199		Green + blue + cool white
	200-208		Green + blue + warm white
	209-217		Blue + warm white + coolwhite
	218-226		Red + green + blue
	227-235		Red + green + blue + cool white
	236-244		Green + blue + cool white + warm white
	245-255		Red + green + blue + cool white + warm white
4	000-016		No function
	017-033		Background red
	034-050		Background green
	051-067		Background blue
	068-084		Background cool white
	085-101		Background warm white
	102-118		Background red + green
	119-135		Background green + blue
	136-152		Background red + blue
	153-169	Background red + green
	170-186	Background green + blue
	187-203	Background red + warm white
	204-220	Background red + green
	221-237	Background green + blue
	238-254	Background red + blue
	255	Background blue + warm white
5	000-001	No function
	002-255	Base tint
6	000-010	No function
	011-220	Effects (68 types, one effect with 3 values)
	221-255	No function
7	000-255	Effect speed
8	000-255	Red dimming
9	000-255	Green dimming
10	000-255	Blue dimming
11	000-255	Cool white dimming
12	000-255	Warm white dimming

40/80/160 CHANNELS

40CH	80CH	160CH	VALUE	DESCRIPTION
1	1	1	000-255	Red dimming 1 group
2	2	2	000-255	Green dimming 1 group
3	3	3	000-255	Blue dimming 1 group
4	4	4	000-255	Cool white dimming 1 group
5	5	5	000-255	Warm white dimming 1 group
6	6	6	000-255	Red dimming 2 group
7	7	7	000-255	Green dimming 2 group
8	8	8	000-255	Blue dimming 2 group
9	9	9	000-255	Cool white dimming 2 group
10	10	10	000-255	Warm white dimming 2 group
11	11	11	000-255	Red dimming 3 group
12	12	12	000-255	Green dimming 3 group
13	13	13	000-255	Blue dimming 3 group
14	14	14	000-255	Cool white dimming 3 group
15	15	15	000-255	Warm white dimming 3 group
16	16	16	000-255	Red dimming 4 group
17	17	17	000-255	Green dimming 4 group
18	18	18	000-255	Blue dimming 4 group
19	19	19	000-255	Cool white dimming 4 group
20	20	20	000-255	Warm white dimming 4 group
21	21	21	000-255	Red dimming 5 group
22	22	22	000-255	Green dimming 5 group
23	23	23	000-255	Blue dimming 5 group
24	24	24	000-255	Cool white dimming 5 group
25	25	25	000-255	Warm white dimming 5 group
26	26	26	000-255	Red dimming 6 group
27	27	27	000-255	Green dimming 6 group
28	28	28	000-255	Blue dimming 6 group
29	29	29	000-255	Cool white dimming 6 group
30	30	30	000-255	Warm white dimming 6 group
31	31	31	000-255	Red dimming 7 group
32	32	32	000-255	Green dimming 7 group
33	33	33	000-255	Blue dimming 7 group
34	34	34	000-255	Cool white dimming 7 group
35	35	35	000-255	Warm white dimming 7 group
36	36	36	000-255	Red dimming 8 group
37	37	37	000-255	Green dimming 8 group
38	38	38	000-255	Blue dimming 8 group
39	39	39	000-255	Cool white dimming 8 group
40	40	40	000-255	Warm white dimming 8 group
	......	......	......	......
	76	76	000-255	Red dimming 16 group
	77	77	000-255	Green dimming 16 group
	78	78	000-255	Blue dimming 16 group
	79	79	000-255	Cool white dimming 16 group
	80	80	000-255	Warm white dimming 16 group
		......	......	......
		156	000-255	Red dimming 32 group
		157	000-255	Green dimming 32 group
		158	000-255	Blue dimming 32 group
		159	000-255	Cool white dimming 32 group
		160	000-255	Warm white dimming 32 group

The products referred to in this manual conform to the European Community Directives to which they are subject:

European Union

Tronios B.V.,

7602KR Almelo, The Netherlands

2014/35/EU

2014/30/EU

2011/65/EC

United Kingdom

Tronios Ltd.

130 Harley Street,

London W1G 7JU, United Kingdom

S.I. 2016:1101

S.I. 2016:1091

S.I. 2012:3032

BEAMZ

is a leading developer of lighting products, including intelligent DMX moving heads, wireless battery operated DMX effects, static washes, sound-activated club effects, strobes & blacklights, LED lighting, fog and special effects machines, lasers and indoor and outdoor architectural lighting, as well as lighting controllers and protective bags.