NXA6-200 - Receiver Ecler - Free user manual and instructions

USER MANUAL NXA6-200 Ecler

b) 0-10 VOLTS DC GENERATOR + ⊕ ⊖

c) MUTE DRY CONTACT

Processing:
A/D & D/A	24 bit, 48kHz. 115dB AKM Codec
DSP	32/64 bits
Latency	2ms
Analog Input headroom:	+18 dBV = +21dBu
Digital Input attenuator:	Stepless from -∞ to +0dB
Input Impedance:	Balanced, 22kΩ
Maximum Delay:	1s (343.4m) for each channel
Delay resolution:	20.8μs (6mm)
Compressor / Limiter:
Threshold	from -36dBV to +18dBV
Ratio	1:1 to ∞:1 (limiter)
Attack time	Auto or from 0.1ms to 500ms.
Release time	Auto or from 1ms to 5s.
Output peak voltage limiter:
Peak voltage upon model (auto settings)	From 10Vpk to 70Vpk
High & Low pass Crossover filters	Butterworth in 6/12/18/24dB/oct.Bessel in 12/18/24dB/octLinkwitz-Riley in 12/24dB/oct.
Parametric Eq. types (8 max. per output)	- Bypass / On-Off all channels- Param. Eq. 20Hz-20kHz; -60/+12dB; Q from =.3 to 200- Low & High Shelf 6/12 dB/oct- Low & High Pass 6/12 dB/oct.- All-Pass 1/2 order
Built In signal generator	- Sine (20Hz to 20kHz)- Polarity(10/20Hz to 10/20kHz)- White- Pink
Signal Mute	Yes
Signal Polarity Invert	Yes
Connectivity:	- Ethernet Base-Tx 10/100Mb, Auto X-Over, Cat5- RS232 57600(fixed)-8-N-1-N

SOFTWARE

EclerNet Software	- Realtime full GUI of all functions and controls thru Ethernet with interactive graphical display- Grouping mode channels or devices- Automated report generation- Remote power on with programmable delay.- Up to 256 devices on same net.- Autodiscovery devices feature- Routing capability through NAT gateways.- Real time metering at input/output (DSP)- Device “Finder” feature- Save & Recall setup and preset functions- Firmware update capability thru Ethernet- Password protection- Default Network configuration:IP: 192.168.0.100Mask: 255.255.255.0Gate: 192.168.0.1UDP Port: 2210
Operating System:	Windows®: XP Prof. (SP3); Vista (SP1); W7(SP1), W8, W10 and W11.
Minimum EclerNet System Requirements:	Pentium IV ® 2GHz500MB RAM100MB HDD free space1024x768 pixels & 16bits colour display10/100/1000 Ethernet Network card

TP-NET PROTOCOL

SOFTWARE

Third-Party NET

USER MANUAL

11 TP-NET PROTOCOL INTRODUCTION

The TP-NET protocol lets a client device (control device) get and/or set the values of several parameters of the EclerNet compatible devices (MIMO and MIMO SG series digital matrices, DUO-NET PLAYER, NXA digital audio manager series, NZA amplifier series, NPA amplifier series, etc.), like volumes, mutes, alarms, etc. It's as well available for eMIMO1616 digital matrix, HUB series digital zoner, MIMO7272DN and MIMO4040CDN digital matrix.

The communication with these digital audio devices can be established using Ethernet and the UDP/IP transport protocol, always by means of the 5800 UDP port.

A second option for this communication is using the RS-232 interface that some of these compatible devices do also have (MIMO series, DUO-NET PLAYER, NXA series, etc.). In this case, the serial connection must fulfil the following specifications:

• Baud rate: 57600 (fixed, no autonegotiation) for all the devices, except for DUO-NET PLAYER, eMIMO1616, HUB series and MIMO4040CDN, which use 115200 baud rate)
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None

In case the Ecler device has an Euroblock connector for the RS-232 interface, the serial cable wiring, from the device's connector to a standard DB9 serial interface connector, must be the following:

WIRING RS232 – DB9
RS232	DB9
Tx	Pin 2 (RxD)
Rx	Pin 3 (TxD)
Gnd	Pin 5 (Signal Gnd)

The protocol is simple and direct, making it easy to read, write and modify the generated code. It is based on messages with no begin and end delimiter: each message is self-delimited by the UDP packet size, which is defined with a maximum of 80 characters. All the messages must be written in capital letters.

To let some control systems (like CRESTRON®, EXTRON®, AMX®, RTI®, VITY®, MEDIALON®, etc.) process the messages more easily, the EclerNet device adds the character LF (0x0A) to the end of each message. This way the client can buffer the messages to process them, if it's required. The EclerNet device can also handle several messages received in a single message packet by using the LF delimiter.

The available messages are built with one or more fields separated with blank spaces ( = blank space):

[PARAM1] [PARAM2] [PARAM3] [PARAM4][LF]

The first field (TYPE) defines the message type and then, the required parameters for it (each kind of message requires a given number of parameters). The field TYPE can have these values:

• SYSTEM
  • GET
• SET
  • INC
  • DEC
• SUBSCRIBE
• UNSUBSCRIBE
• DATA
• ERROR

At the end of this document you'll find all the available messages and their parameters for each model of the EclerNet compatible devices.

The SYSTEM, GET, SET, INC, DEC, SUBSCRIBE & UNSUBSCRIBE messages can be sent from the client to the EclerNet device. The DATA & ERROR messages can be sent from the device to the client. The only exception is the SYSTEM PING message, that is a SYSTEM type message that is sent from the EclerNet device when the initial message from the client to the device was SYSTEM CONNECT PINGPONG.

The communication (using UDP or RS-232) starts when a client sends the message SYSTEM CONNECT to the EclerNet device. As far as the UDP communication requires no connection (unlike the TCP), the EclerNet device stores this client's IP address, and then uses it as the destination IP address for the messages that it generates (DATA & ERROR). After receiving the SYSTEM CONNECT message, the device dumps its entire configuration using several consecutive DATA messages.

Note: if the configuration data dump process (usually a huge list of parameters & values) wants to be avoided after a SYSTEM CONNECT message, a SYSTEM CONNECT ONCE message can be used instead.

The communication can be terminated by two methods:

- Manually: when the client sends the SYSTEM DISCONNECT message, cancelling all the subscriptions and stopping the DATA & ERROR messages

- Automatically: in case the initial message was SYSTEM CONNECT PINGPONG and the client didn't get any SYSTEM PONG message in a period longer than 10 seconds (presuming a communication breakdown)

The SET messages don't have an automatic acknowledgement with a DATA message sent from the EclerNet device after it has processed the SET command. The client must update the values itself and must send the needed GET message if it requires confirmation from the device.

NOTES:

• The numerical values are always integer numbers without +, -, comma or dot symbols.
• [PINGPONG] is an optional parameter used to configure the device-client communication with a periodical check, to see whether the client or the device have terminated it. When configured this way, the device sends a SYSTEM PING once per second, and the client must answer with a SYSTEM PONG message. If anyone doesn't get these messages along a 10 seconds period, the communication will be considered terminated.
• [ONCE] is an optional parameter used to start the device-client communication without a full data dump process (usually a huge list of parameters & values).
• &
  are numerical values that identify an input or output channel of the EclerNet device. For the NXA series it can be within the [1..4] or [1..6] range, for 4 or 6 channel amplifiers.
• is a numerical value that identifies one available Preset stored in the EclerNet device's memory. For the NXA and NZA series it can be within the [1..5] range.
• ,

   y  are numerical values in the [0..100] range that define values in a scale equivalent to [-inf..0] dB.   

• & are numerical values. For the NXA series GPI values can be within the [1..4] or [1..6] range, depending on model.
• is a numerical value within the [0..100] range that indicates the value of an analogue GPI input. For a digital input only 0 or 100 are the possible values.
• is a numerical value within the [0..1] range: it can only be 0 or 1 (opened or closed GPO).
• is a numerical value within the [1..10] range that sets the VU-meter refresh rate, or the number of times the vumeters' values are sent per second (by default = 3).
• "" is the device name inside double quotation marks, to allow for names with blank spaces.
• is a numerical value for an error code.

- "" is a text chain inside double quotation marks, containing an error description.

- is a numerical value that identifies a Virtual Control. - It can be within a [1A..4A] or [1B..4B] range for NXA 4 ch. Models.

- It can be within a [1A..6A] or [1B..6B] range for NXA 6 ch. Models.

ecler

12 NXA DIGITAL AUDIO MANAGER SERIES

IMPORTANT NOTE: The communication must be started with the client sending the first message SYSTEM CONNECT or SYSTEM CONNECT ONCE to the EclerNet device. Otherwise, the commands from the client to the EclerNet device will be ignored. See TP-NET PROTOCOL INTRODUCTION chapter for additional information.

TYPE	PARAM1	PARAM2	PARAM3	PARAM4	DESCRIPTION
SYSTEM	CONNECT	[MASTER]	[PINGPONG]	[ONCE]	MASTER: this parameter, applied in SYSTEM CONNECT, is used to disconnect all clients currently connected to the device, releasing all open and not correctly closed connections, opening a new connection. In this way we guarantee that the client that has set the MASTER option is the only one connected by TP-NET to the device.PINGPONG: this parameter can be used with the MASTER parameter, the difference is that this parameter performs a periodic check to see if the communication is still open (PING PONG) or if after 10 seconds with no response, the communication has ended (PING).ONCE: this parameter is used to prevent the device status dump.
	DISCONNECT				Cancel subscriptions and terminates communication
	SUBSCRIPTION_RATE				Alive message from device
	PING				Alive message from device
	PONG				Alive ACK message from client
GET	ALL				Dumps current device status (with DATA messages)
	POWER				Gets the Device Power status
	PRESET				Gets the current PRESET
	OLEVEL				Gets the current LEVEL of an Output Channel
	XLEVEL				Gets the current LEVEL of a Matrix point
	OMUTE				Gets the current MUTE status of an Output Channel

ecler

	XMUTE				Gets the current MUTE status of a Matrix Point
	OVU				Gets the VU-meter value of an Output Channel
	ALARM_PROTECT				Gets the Protect alarm status of an Output Channel
	ALARM_FAULT				Gets the self-diagnosis system alarm status of an Output Channel
	INFO_NAME				Gets the Device Name
	INFO_MODEL				Gets the Device Model
	INFO_VERSION				Gets the Firmware Version
	INFO_MAC				Gets the Device MAC address
	VIRTUAL_CONTROL				Gets the Virtual Control value
TYPE	PARAM1	PARAM2	PARAM3	PARAM4	DESCRIPTION
SET	POWER	ON/OFF			Sets the Device Power status
	PRESET				Sets the current PRESET
	OLEVEL				Sets the current LEVEL of an Output Channel
	XLEVEL				Sets the current LEVEL of a Matrix point
			Channel>
	OMUTE		YES/NO		Sets the current MUTE status of an Output Channel
	XMUTE				Sets the current MUTE status of a Matrix Point
			Channel>
	VIRTUAL_CONTROL				Sets the Virtual Control value (Value can range from 1 to 100)
INC	OLEVEL				Increases the current LEVEL of an Output Channel by Value (Value can range from ±1 to ±100)
	XLEVEL				Increases the current LEVEL of a Matrix point by Value (Value can range from ±1 to ±100)
DEC	OLEVEL				Decreases the current LEVEL of an Output Channel by Value (Value can range from ±1 to ±100)
	XLEVEL				Decreases the current LEVEL of a Matrix point by Value (Value can range from ±1 to ±100)
SUBSCRIBE	ALL				Subscribes to all VU-meters
	OVU				Subscribes to an Output Channel VU-meter
UNSUBSCRIBE	ALL				Unsubscribe to all VU-meters
	OVU				Unsubscribe to an Output Channel VU-meter
DATA	POWER	ON/OFF			Shows the Device Power status
	PRESET				Shows the current PRESET
	OLEVEL				Shows the current LEVEL of an Output Channel
	XLEVEL				Shows the current LEVEL of a Matrix point
			Channel>
	OMUTE		YES/NO		Shows the current MUTE status of an Output Channel
	XMUTE			YES/NO	Shows the current MUTE status of a Matrix point
			Channel>
	VIRTUAL_CONTROL				Shows the Virtual Control value

	OVU				Shows the VU-meter value of an Output Channel
	ALARM_PROTECT		ON/OFF		Shows the Protect alarm status of an Output Channel
	ALARM_FAULT		ON/OFF		Shows the self-diagnosis system alarm status of an Output Channel
	INFO_NAME	“”			Shows the Device Name
	INFO_MODEL				Shows the Device Model
	INFO_VERSION				Shows the Firmware Version
	INFO_MAC				Shows the Device MAC address
ERROR		“”			Informs about an error

Note: INC and DEC commands are replied with a DATA command from the device with the resulting LEVEL value, after it has been increased or decreased. When the INC or DEC command tries to adjust a LEVEL value beyond its minimum or maximum limits, no reply (DATA command) will be produced.

13 ERROR CODES FOR ECLERNET DEVICES

13.1 COMMON ERROR CODES (to all EclerNet - TP-NET compatible devices)

ERROR ID	DESCRIPTION
0	TPNET_ERROR_NONE = 0,
1	TPNET_ERROR_INVALID_FIELD_TYPE,
2	TPNET_ERROR_INVALID_FIELD_PARAM1,
3	TPNET_ERROR_INVALID_FIELD_PARAM2,
4	TPNET_ERROR_INVALID_FIELD_PARAM3,
5	TPNET_ERROR_INVALID_FIELD_PARAM4,

13.2 NXA SERIES SPECIFIC ERROR CODES

ERROR ID	DESCRIPTION
6	UDP_ERROR_TIMEOUT_PONG,
7	UDP_ERROR_CONNECT_WHILE_CONNECTED,
8	UDP_ERROR_DISCONNECT_WHILE_UNCONNECTED,
9	UDP_ERROR_INVALID_CLIENT_IP,
10	UDP_ERROR_MESSAGE_TOO_LONG,
11	UDP_ERROR_UNSUPPORTED_MESSAGE,
12	UDP_ERROR_UNSUPPORTED_PRESET_NUMBER,
13	UDP_ERROR_UNSUPPORTED_INPUT_CHANNEL_NUMBER,
14	UDP_ERROR_UNSUPPORTED_OUTPUT_CHANNEL_NUMBER,
15	UDP_ERROR_UNSUPPORTED_GPI_NUMBER,
16	UDP_ERROR_UNSUPPORTED_GPO_NUMBER,
17	UDP_ERROR_INVALID_LEVEL_VALUE,
18	UDP_ERROR_INVALID_RATE_VALUE,
19	UDP_ERROR_GPO_VALUE,
20	UDP_ERROR_MAX_CLIENTS_REACHED,
21	UDP_ERROR_MASTER_MODE,

d ecler