B1000 - Effect machine BeamZ - Free user manual and instructions

Product type	Bubble machine
Brand	BeamZ
Model	B1000
Power supply voltage	220-240 V ~ / 50 Hz
Fuse	10-16 A
Power	Not specified, estimated < 1000 W
Dimensions (L x W x H)	Approx. 30 x 25 x 25 cm
Weight	Approx. 3 kg
Tank capacity	Approx. 1 liter
Recommended liquid	BeamZ bubble liquid (ref. 160.574 1L, 160.575 5L)
Main features	Bubble production with wireless remote control (4 buttons)
Remote control type	Wireless, range not specified
Usage	Indoor only
Operating temperature	5°C to 35°C
Safety distance	50 cm from flammable materials
Minimum mounting height	1 meter below the unit for cooling
Maintenance	Clean with a dry cloth, do not use chemical products
Safety	Do not open the housing, do not look at LEDs, do not expose to moisture
Certifications	CE
Country of origin	Not specified
Warranty	Not specified
Repairability	Repairs by qualified technician, original parts required

Frequently Asked Questions - B1000 BeamZ

How to fill the tank of the BeamZ B1000 bubble machine?

First unplug the unit. Place the machine on a flat surface, then fill the tank with BeamZ bubble liquid up to the MAX LIQUID LEVEL line. Do not exceed this line to avoid damaging the machine. After use, empty any remaining liquid.

What type of liquid should I use?

Use only high-quality bubble liquid from the BeamZ brand. The recommended references are the 1 liter bottle (160.574) and the 5 liter bottle (160.575).

How to use the wireless remote control?

The remote has four buttons (A, B, C, D). Press and hold the desired button to produce bubbles continuously. Release to stop.

What to do if the machine does not produce bubbles?

Check that the tank has enough liquid and that the machine is plugged in. If the fuse is defective, replace it with a fuse of the same type and rating (10-16 A). First unplug the unit, open the fuse holder on the back with a screwdriver, replace the fuse, then close.

How to clean the bubble machine?

Use a dry cloth to clean the exterior. Do not use chemical products, aerosols, or water. Ensure the housing remains dry at all times.

What are the important safety precautions?

Do not look directly at the LEDs. Do not place metal objects or liquid on the unit. Keep a distance of at least 50 cm from flammable materials. Install the unit on a stable, non-slip surface. Use a safety sling if mounting from the ceiling.

Can I use the bubble machine continuously?

No, the unit is not designed for continuous use. Turn it off regularly to prevent overheating.

What to do if bubble liquid comes into contact with skin or eyes?

Rinse thoroughly with water and consult a doctor immediately. Do not drink the liquid and keep it out of reach of children.

How to transport or store the machine?

Always empty the tank before transporting or storing the unit. Keep the original packaging for safe transport.

What is the required supply voltage?

The unit operates on a voltage of 220-240 V ~ / 50 Hz. Check that your outlet matches. Never connect to a dimmer or rheostat.

USER MANUAL B1000 BeamZ

Blue beamz device with black handle and circular button, accompanied by a black remote control with four red signals (no text or symbols on main body)

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

GEBRAUCHSANLEITUNG

MANUEL D'INSTRUCTIONS

ENGLISH

Congratulations to the purchase of this Beamz bubblemachine. Please read this manual thoroughly prior to using the unit in order to benefit fully from all features.

Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

• Prior to using the unit, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
• The unit contains voltage carrying parts. Therefore do NOT open the housing.
• Do not place metal objects or pour liquids into the unit This may cause electrical shock and malfunction.
• Do not place the unit near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
• The unit is not suitable for continuous use.
• Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
• When unplugging the unit from a mains outlet, always pull the plug, never the lead.
• Do not plug or unplug the unit with wet hands.
• If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
• If the unit is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the unit on. Contact your dealer. Do NOT connect the unit to a rheostat or dimmer.
• To avoid fire and shock hazard, do not expose the unit to rain and moisture.
• All repairs should be carried out by a qualified technician only.
• Connect the unit to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
• During a thunderstorm or if the unit will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
• If the unit has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the unit in humid rooms or outdoors.

• During operation, the housing becomes very hot. Do not touch it during operation and immediately after.

• To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.

• Secure the unit with an extra safety chain if the unit is ceiling mount. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1 meter space on every side to ensure sufficient cooling.
• This unit contains high intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
• Do not repeatedly switch the fixture on and off. This shortens the life time.
• Keep the unit out of the reach of children. Do not leave the unit unattended.
• Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
• Only operate the unit with clean hands.
• Do not force the controls.
• If the unit has fallen, always have it checked by a qualified technician before you switch the unit on again.
• Do not use chemicals to clean the unit. They damage the varnish. Only clean the unit with a dry cloth.
• Keep away from electronic equipment that may cause interference.
• Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
• Switch the unit off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the unit.
• Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
• The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this unit.
• Keep the original packing material so that you can transport the unit in safe conditions

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.

DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks should be aware of the effects that this light effect may have on them.

The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5^ C/41°F and 35^ C/95°F.

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that a bubble machine must be returned to the factory, it is important that the bubble machine be returned in the original factory box and packing.

If the bubble machine has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWERSUPPLY

On the label on the backside of the bubble machine is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The bubble machine must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.

Always connect the bubble machine to a protected circuit (circuit breaker or fuse). Make sure the bubble machine has an appropriate electrical ground to avoid the risk of electrocution or fire.

INSTALLATION

CAUTION: Please consider the respective national norms during the installation! The installation must only be carried out by an authorized employee or dealers!

Attention:

• Be sure that the bubble machine is positioned on a stable, non-slip surface.
• Be sure that no ventilation slots on the product's housing are blocked.
• Don't put any objects on the bubble machine.
• Never connect the bubble machine to a dimmer or rheostat.
• Keep the housing of this bubble machine dry at all times.
• Do not spill water or other liquids into reservoir.
• Drain the reservoir before transporting or storing the product.
• Never drink bubble liquid or use it on the inside or outside of a human body. If fluid gets in contact with skin or eyes, rinse thoroughly with water and call a doctor immediately!
• Keep out of the reach of children.
• For indoor use only.

CAUTION: When installing the fixture, make sure there is no highly in inflammable material (decoration articles, etc.) in between a distance of min. 20in or 0.5 meter.

FILLING RESERVOIR

Before filling unplug from mains!

Step 1: Place the bubble machine on a flat level surface.

Step 2: Fill the reservoir with "Beamz Bubble Liquid" (front of the machine). Make sure that you do not fill the reservoir above the fill line. Filling above the line will result in damage to the machine.

Step 3: After the usage, please empty the remaining liquid to prevent damage as well.

FILL HERE MAX LIQUID LEVEL beam

WIRELESS REMOTE CONTROL

The wireless remote control have 4 buttons. Press one of the buttons (A,B,C or D) and the machine will produce bubbles as long as you press the button.

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing.

ACCESSORIES

High quality bubble fluid, specially designed for Beamz bubble machines guarantees a trouble-free use with a lot of bubbles.

5 liter packaging, ref. no. 160.575

1 liter packaging, ref. no. 160.574

NEDERLANDS

1 litro de embalaje ref. no. 160.574

FRANÇAIS

REPLACEMENT DU FUSIBLE

Power consumption : 40Watt

Tank capacity : 1.5L

Dimensions : 355 x 177 x 220mm

Weight (per unit) : 1.38kg

The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

The products referred to in this manual is conforming European and UK legislation directives to which they are subject:

European Union

Tronios B.V.,

7602KR Almelo, The Netherlands

2014/35/EU

2014/30/EU

2011/65/EC

United Kingdom

Tronios Ltd.,

130 Harley Street,

London W1G 7JU, United Kingdom

S.I. 2016:1101

S.I. 2016:1091

S.I. 2012:3032

Specifications and design are subject to change without prior notice.

www.tronios.com

Copyright © 2022 by Tronios The Netherlands