GTHS 6045.1 - Hedge trimmers Güde - Free user manual and instructions

Product type	Telescopic hedge trimmer
Brand	Güde
Model	GTHS 6045.1
Order number	95102
Power supply	230 V ~ 50 Hz
Motor power	600 W (P1)
Protection type	II (double insulation)
Protection rating	IP20
Cutting length	450 mm
Cutting bar length (with reinforcement)	530 mm
Maximum cutting thickness	18 mm
Net weight	4.2 kg
Sound pressure level (LpA)	82.7 dB(A)
Measured sound power level (LWA)	95.9 dB(A)
Guaranteed sound power level (LWA)	104 dB(A)
Vibration emission value (ah)	2.37 m/s²
Intended use	Trimming shrubs and hedges in private gardens
Minimum age required	18 years (except vocational training)
Recommended protective equipment	Hearing protection, eye protection, gloves, safety shoes, helmet
Cleaning frequency	Before each use: visual inspection; after use: cleaning and oiling the bar
Warranty	24 months for the end consumer
After-sales service	www.guede.com or [e-mail]

Frequently Asked Questions - GTHS 6045.1 Güde

How to use the hedge trimmer safely?

Read the instruction manual carefully before use. Always wear hearing protection, eye protection, gloves, a helmet, and safety shoes. Make sure no one is in the danger zone. Do not use in rain or damp environments. Unplug the appliance before any maintenance.

What are the power and supply of the appliance?

The Güde GTHS 6045.1 hedge trimmer is powered by 230 V ~ 50 Hz with a motor power of 600 W. It has protection class II (double insulation).

How to adjust the cutting height?

The device is telescopic: you can extend the extension pole to work at height or use it without the pole for low areas. Adjust the length of the safety harness for optimal balance.

What are the cutting characteristics?

The cutting length is 450 mm with a reinforced blade bar of 530 mm. The maximum cutting thickness is 18 mm, suitable for fine and medium branches.

How to maintain the hedge trimmer?

Before each use, perform a visual inspection of the cable and plug. After use, clean the cutting bar with a brush and apply a light oil. Store the appliance in a dry, frost-free place. Have the bar sharpened regularly by an authorized workshop.

What to do if the blades jam?

Immediately unplug the appliance before removing the obstructing object. Never touch moving blades. Wear protective gloves to remove the debris.

What are the noise and vibration levels?

The sound pressure level is 82.7 dB(A) and the guaranteed sound power level is 104 dB(A). Wear hearing protection. The vibration emission value is 2.37 m/s².

Can I use an extension cord?

Yes, only use an extension cord suitable for outdoor use with sufficient cross-section to avoid voltage drops. Ensure it is not damaged.

How to store the appliance?

Clean and lightly oil the cutting bar, then store the appliance in a dry place, protected from light and frost, out of reach of children. Use the blade sheath to protect the bar.

What to do if the appliance does not work or vibrates abnormally?

First check that the plug is properly connected and the cable is not damaged. If the problem persists, the appliance may be defective. Contact Güde after-sales service ([e-mail]) for repair by an authorized technician.

USER MANUAL GTHS 6045.1 Güde

Translation of the original instructions Telescopic hedge trimmer

GTHS 6045.1 95102

GTHS 6045.1

95102

GÜDE GmbH & Co. KG

Birkichstrasse 6

74549 Wolpertshausen

Deutschland

ENGLISH Please read the instructions carefully before starting the machine.

Scanned document with a list of items and a blue button labeled 'SICUNow' in the bottom right corner.

1

Blue and black electric shaver tool with attached spring, shown against white background (no text or symbols)

2

Black plastic object with a triangular handle and circular hole (no text or symbols)

3

Black and white photo of a black athletic belt buckle with a loop handle (no text or symbols visible)

Gerätebeschreibung

EN Device description FR Description du dispositif IT Dotazione ES Descripción del dispositivo NL Beschrijving van het apparaat CZ Popis zařízení SK Opis zariadenia PL Opis urządzenia HU Eszközleírás

(3) (9) (9) (2) (5) (1) (8) (4) (7)(6)

Gerätebeschreibung

EN Device description FR Description du dispositif IT Dotazione ES Descripción del dispositivo NL Beschrijving van het apparaat CZ Popis zařízení SK Opis zariadenia PL Opis urządzenia HU Eszközleírás

English Technical Data / Device description / Safety Warnings / Specified Conditions of Use / Emergency procedure / Symbols / Maintenance / Disposal / Guarantee / Service 19

EN starting-up the device FR Mise en service IT Messa in funzione

ES Puesta en marcha NL Toestel in gebruik nemen cz Uvedení do provozu

Close-up of a blue electric shaver tool with a black cable and spring, no visible text or symbols

Blue handheld device with lock and rotating arm mechanism (no text or symbols)

Close-up of a black handheld device with a handle and connector, showing alignment instructions (no text or symbols)

Mechanical component diagram showing a rotating shaft and housing with a hexagonal nut (no text or symbols)

3 CLICK 3

Illustration of a black tool with a blue handle and a green checkmark above it, against a white background (no text or symbols)

1

2

Warning symbols and hazard icons including power, warning sign, safety signs, head protection, helmet, hand gesture, and person wearing a mask

Three-panel illustration showing a person with a shoe, checkmark, and crossed-out red lines, likely illustrating safety or compliance issues.

START 1 2

STOP

60° ± 10°

Person spraying a leafy hedge with a tool, no text or symbols visible

Person using a manual gun to spray green foliage, no text or symbols visible

TIP 10 cm 100 cm

3D rendered green textured block with a white outline and a green checkmark (no text or symbols)

1

Diagram showing a blue-handled tool emitting red and black spray from a wire, with no visible text or symbols.

Safety warning sign showing three pictograms (no litter, running person, snowflake) above a storage shelf with a green checkmark indicating inspection.

Technische Daten

Teleskop Heckenschere......GTHS 6045.1

Artikel-Nr. 95102

Degree of protection IP 20

Protection class ....II

Cutting length 450 mm

Beam length 530 mm

Max. cut thickness 18 mm

Net weight 4,2 kg

Noise and Vibration Information

Sound pressure level L ^1) 82,7 dB(A)

Measured sound power level L _WA^1) 95,9 dB(A)

Guaranteed sound power level L 104 dB(A)

Wear ear protectors!

Vibration emission value a_h^2) .....2,37 m/s ^2

^1) Uncertainty K=3 dB (A), ^2) Uncertainty K=1,5 m/s ^2

Warning: The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet.

The vibration emission level may be used to compare one tool with another.

It may be used for a preliminary assessment of exposure.

An accurate estimate of the vibratory load should also take into account the times when the tool is shut down or when it is running but not actually in use. This may significantly reduce the vibratory load over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration such as maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

Read and understand the operating instructions before using the appliance. Abide by all the safety measures stated in the

service manual. Act responsibly toward third parties. In case of any doubts about connection and operation refer please to our customer center

Specified Conditions Of Use

The hedge trimmer is designed for trimming shrubs and hedges in private hobby gardens

The device must not be used for crushing compost, as persons or damage to property können. The hedge trimmer is designed for trimming shrubs and hedges in private hobby gardens.

Do not use this product in any other way as stated for normal use. Not observing general regulations in force and instructions from this manual does not make the manufacturer liable for damages.

Requirements for operating staff

The operating staff must carefully read the Operating Instructions before using the appliance.

Qualification : Apart from the detailed instructions by a professional, no special qualification is necessary for appliance using.

Training : Using the appliance only requires corresponding training by a professional or the Operating Instructions. No special training is necessary.

The operator is responsible for accidents or risks to third parties.

Observe to keep out of dangerous zone

Emergency procedure

Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. For the sake of eventual accident, in accordance with DIN 13164, a workplace

has to be fitted with a first-aid kit. It is essential to replace any used material in the first-aid kit immediately after it has been used.

If you seek help, state the following pieces of information:

1. Accident site
2. Accident type
3. Number of injured persons
4. Injury type(s)

Symbols

Caution!

Read the Operating Instructions!

Wear eye protection! Wear ear protectors!

Wear protective helmet!

Wear protective gloves!

Unplug the trimmer from socket before maintenance and working on the trimmer.

Wear safety cut through resistant shoes with safety sole and steel toe!

Warning against thrown-off items

Warning against thrown-off items

Keep distance of persons Observe to keep out of dangerous zone

Warning against cutting injuries

Electrical hazard, keep at least 10 m distance away from electrical power lines.

Protect against humidity Never expose tool to rain.

The trimmer has a protective insulation

Any damaged or disposed electric or electronic devices must be delivered to appropriate collection centres.

General Power Tool Safety Warnings

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term „power tool“ in the warnings refers to your mains-operated (cordepower tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (groundepower tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device

(RCprotected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Additional safety instructions Hedge trimmer

• Keep parts of your body off the cutting blade. Do not remove jammed material while the blades are moving.
• When removing jammed material, make sure the appliance is off.
• Attach the knife protection for transport or storage. Before you start with the work, search the thicket for hidden objects such as wire fences, etc.
• Do not let children, other persons or pets near the cutting scissors.
• Do not use the cutting scissors if the cutting tool is not fitted properly or when it is damaged.
• Before adjusting the cutting scissors, make sure the knives or blades do not touch stones or debris.
• Do not cut any hard objects. This could lead to accidents and damage the cutting scissors.
• Avoid abnormal posture and do not work above shoulder height.
• Respect the system voltage!
• Do not attempt to remove shavings when the knives are moving. When removing any jammed material, make sure the cutting scissors are off and stopped. When lifting or holding the cutting scissors, do not hold the cutting knives.

CAUTION: Knives are still running for a short time after being switched off.

Putting into operation for your safety

Before carrying out any work on the machine, disconnect the plug from the socket.

Please observe the legal provisions of regulations on protection against noise. These provisions can be different in various places.

Attaching the shoulder safety strap

⚠ Caution! Always use the shoulder strap when working. Switch off the appliance before releasing the shoulder strap.

• Place the shoulder strap over your shoulders.
• Adjust the strap length so that the strap holder is at the height of your hips.
  ⚠️ Never wear the strap diagonally over your shoulders and chest but only on one shoulder. By this, the appliance can quickly be taken off your body in case of emergency.

Height adjustment

Depending on the working height, an extension can be fitted or you can work without extension in lower areas..

Maintenance

Before using the appliance, perform a visual inspection at all times to make sure the power cord and the plug, in particular, are not damaged on the charger.

The machine must not be used under any circumstances if the machine or the safety devices are damaged.

If the device is defective, the repair has to be made exclusively by the customer service.

Use only original accessories and original spare parts.

The operating staff must carefully read the Operating Instructions before using the appliance.

Cleaning and storage

Caution! Always remove the battery from the appliance and possibly wear protective gloves before cleaning and storing.

At regular intervals, clean the clamping mechanism by blowing it by compressed air or clean it with a brush.

Keep the handles dry (no oil) for safe holding. Clean the appliance with a damp cloth or a mild detergent.

Keep your appliance and its accessories in a dark, dry and frost-free place inaccessible to children.

Guarantee

Warranty period of 12 months applies to commercial use and 24 months applies to private use and commences on the day of purchase of the device.

The guarantee does not cover any unauthorised use such as appliance overloading, use of violence, damage as a result of any unauthorised interference or caused by foreign items.

Failing to follow the operating and assembly instructions and common wear are.

Service

Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions? We will quickly help you and without needles bureaucracy at our web pages at www.guede.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be found on the type label. Please enter it here for future reference

Serial No.:

Art. No:

Year of production:

Tel.: [phone] / 700-360

Fax: [phone]

E-Mail: [e-mail]

Disposal

Note to the disposal arising from icons placed on the appliance or on the package. Description of the meanings can be found in section "Marking".

Do not dispose of electrical appliances in household waste.

According to European Directive 2002/96/EC on waste electrical and electronic equipment and transposition to the national law, worn electrical equipment must be collected separately and put to recycling.

Recycling alternative to the return requirement:

As an alternative to recycling, the owner of the electrical equipment is obliged to provide assistance in professional recycling. For this purpose, an old appliance can be put to a collection centre that will dispose of it in accordance with the national circulation management and the Waste Act.

This does not apply to accessories connected to old appliances and auxiliary equipment without

electrical components.

Transport packaging disposal

The packaging protects the appliance against damage during transport. Packaging materials are usually chosen according to environmental-friendliness and waste treatment aspects and can therefore be recycled. Returning the packaging to material circulation saves raw materials and reduces waste. Parts of packaging (e.g. foils, styrofoam ^® ) can be dangerous to children.

Risk of suffocation! Keep the packaging out of reach of children and dispose them as quickly as possible.

Inspection and maintenance plan

Generally Whole appliance		Regularly clean the outer partLet regularly checked by authorized workshop
	Plastic bodyKnife/cutter bar	Check for cracks and fissuresLet regularly sharpen
Before any start-up ON/OFF switch Functional test
storage Whole appliance To be cleaned and the knife bar slightly lubricated.
		To be safely stored in a cold room. Have it checked in a specialised workshop.

Failures - Causes - Removal

Failures Causes Removal
Cutting scissors not working.	Appliance is defectiveInternal cables are defective	Consult with the customer service centreConsult with the customer service centre
Unsteady running, strong vibrations	Appliance is defective Consult with the customer service centre

Âge minimal : Persons over 18 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education.

Risk of injury if the On/Off button is pressed unintentionally.

Fonctionnement

Apparaat is randgeaard

Translation of the EC-Declaration of Conformity

We, hereby declare the conception and construction of the below mentioned appliances correspond - at the type of construction being launched - to appropriate basic safety and hygienic requirements of EC Directives.

In case of any change to the appliance not discussed with us the Declaration expires.

TELESKOP HECKENSCHERE

Hedge Trimmer | Taille-Haies | Forbice Tagliasiepi | Heggenschaar | Nǚžky Na Živ. Plot | Nožnice Na Živ. Plot | Sövénynyíróolló | Škarje Za Živo Mejo | Škare Za Živicu | Ножица За Жив Плет | Foarfecă De Gard Viu | Makaze Za Živicu | nożyce do żywopłotu

95102

GTHS 6045.1

Notified Body Name: No: Adress:

Type Ex. Cert.-No.:

97/68/EC_&2016/1628/EU

Emission No.:

2000/14/EC_2005/88/EC