KD-R862BT, KD-R862BTE - Bluetooth Car Stereo JVC - Free user manual and instructions

USER MANUAL KD-R862BT, KD-R862BTE JVC

Warning Do not operate any function that takes your attention away from safe driving. Caution Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level. General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
• USB rating is indicated on the main unit. To view, detach the faceplate. ( 3) Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately. Maintenance How to read this manual
• Operations are explained mainly using buttons on the faceplate of KD-R861BT.
• English language is used for the display explanation in this manual.
• [XX] indicates the selected items.
• ( XX) indicates references are available on the stated page. Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth. Cleaning the connector: Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector. Handling discs:
• Do not touch the recording surface of the disc. Connector (on the reverse
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it. side of the faceplate)
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.

JS_JVC_KD_R961BT_E_EN_1.indd 2 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 23/7/2014 1:45:05 PM BASICS Faceplate Remote control (RM-RK52) Display window KD-R961BT KD-R961BT can be remotely controlled with an optionally purchased remote control. Remote sensor (Do not expose to bright sunlight.) Volume knob (turn/press) Loading slot Pull out the insulation sheet when using for the first time. Detach button Attach Remote control functions are not available for KD-R864BT / KD-R862BT / KD-R861BT. Detach How to reset How to replace the battery Your preset adjustments will also be erased.

On the faceplate Turn on the power Press

• Press and hold to turn off the power. On the remote control Adjust the volume Turn the volume knob. Press Press the volume knob to mute the sound or pause playback.
• Press again to cancel. Press to mute the sound or pause playback.
• Press again to cancel. Select a source

• Press repeatedly. , then turn the volume knob within 2 seconds. Press SOURCE repeatedly. Change the display information Press repeatedly. ( 20)

Cancel the demonstration Press and hold Turn the volume knob to select [DEMO], then press the knob. Turn the volume knob to select [DEMO OFF], then press the knob. Press to exit.

AM * AUX * YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated). For details on how to update the firmware, see: <http://www.jvc.net/cs/car/>. CLOCK CLOCK SYNC AUTO: The clock time is automatically set using the Clock Time (CT) data in FM Radio Data System signal. ; OFF: Cancels. CLOCK DISP ON: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels. ENGLISH Selected language is use as the display language for menu and Tag information (folder name, file name, song title, artist name, album name) if applicable. By default, the menu language is: ENGLISH

• Not displayed when the corresponding source is selected. Set the basic settings

1 Press and hold 2 Turn the volume knob to make a selection (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit. To return to the previous setting item, press

On the faceplate Reverse / Fast-forward*3 Press and hold Select a track/file Press

Press Select a folder*4 Press

Press Repeat play*5 Press repeatedly.

: iPod or ANDROID *1 Do not leave the cable inside the car when not using. *2 When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting. ( 19) *3 For ANDROID: Applicable only when [AUTO MODE] is selected. ( 6) *4 For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID. *5 For iPod/ ANDROID: Applicable only when [HEAD MODE]/ [AUTO MODE] is selected. ( 6) ENGLISH JS_JVC_KD_R961BT_E_EN_1.indd 5 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

On the faceplate Select control mode While in iPod source, press repeatedly. HEAD MODE: Control from the unit. IPHONE MODE: Control from the iPod/iPhone. However, you can still play/pause or file skip from the unit. While in ANDROID source, press repeatedly. AUTO MODE: Control from the unit (using JVC MUSIC PLAY application). AUDIO MODE: Control other media player applications from the Android device (without using JVC MUSIC PLAY application). However, you can still play/pause or file skip from the unit. Select music drive Press repeatedly. The stored songs in the following start playback.

• Selected internal or external memory of a smartphone (Mass Storage Class).
• Selected drive of a multiple drives device. Change the playback speed of the Audiobook Select a file from a folder/list 1 Press 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob. Quick Search If you have many files, you can search through them quickly. For MP3/WMA/AAC/WAV or JPC / JMC file: Turn the volume knob quickly. For iPod: You can search for a file according to the first character. Press or turn the volume knob quickly to select the desired character (A to Z/ 0 to 9/ OTHERS).
• Select “OTHERS” if the first character is other than A to Z, 0 to 9.
• To return to the previous setting item, press

• For iPod, applicable only when [HEAD MODE] is selected. ( Select control mode)
• For ANDROID, applicable only when [AUTO MODE] is selected. ( Select control mode) While listening to the iPod and [HEAD MODE] is selected ( Select control mode).... 1 Press and hold 2 Turn the volume knob to select [IPOD], then press the knob. 3 Press the volume knob to select [AUDIOBOOKS]. 4 Turn the volume knob to make a selection, then press the knob. 0.5× SPEED / 1× SPEED / 2× SPEED: Select the desired playback speed of the Audiobooks sound file in your iPod/iPhone. (Default: Depends on your iPod/iPhone setting.) 5 Press to exit. To return to the previous setting item, press

JS_JVC_KD_R961BT_E_EN_1.indd 6 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 23/7/2014 1:45:12 PM RADIO Select a stored station Press one of the number buttons (1 to 6). (or) 1 Press 2 Turn the volume knob to select a preset number, then press the knob to confirm. “ST” lights up when receiving an FM stereo broadcast with sufficient signal strength. Search for a station repeatedly to select FM or AM. 1 Press 2 Press (or press on RM-RK52) to search for a station automatically. (or) Press and hold (or press and hold on RM-RK52) until “M” flashes, then press repeatedly to search for a station manually. Other settings 1 Press and hold 2 Turn the volume knob to select [TUNER], then press the knob. 3 Turn the volume knob to make a selection (see the following table), then press the knob. 4 Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item. to exit. To return to the previous setting item, press

5 Press Default: XX Settings in memory You can store up to 18 stations for FM and 6 stations for AM. Store a station While listening to a station.... Press and hold one of the number buttons (1 to 6). (or) 1 Press and hold the volume knob until “PRESET MODE” flashes. 2 Turn the volume knob to select a preset number, then press the knob. The preset number flashes and “MEMORY” appears. RADIO TIMER Turns on the radio at a specific time regardless of the current source. 1 ONCE/ DAILY/ WEEKLY/ OFF: Select how often the timer will be turned on. 2 FM/ AM: Select the source. 3 01 to 18 (for FM)/ 01 to 06 (for AM): Select the preset station. 4 Set the activation day *1 and time. “M” lights up when complete. Radio Timer will not activate for the following cases.

• The unit is turned off.
• [OFF] is selected for [AM] in [SRC SELECT] after Radio Timer for AM is selected. ( 4) *1 Selectable only when [ONCE] or [WEEKLY] is selected in step 1. ENGLISH JS_JVC_KD_R961BT_E_EN_1.indd 7 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

23/7/2014 1:45:12 PM AUX RADIO SSM SSM 01 – 06 / SSM 07 – 12 / SSM 13 – 18: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select SSM 07 – 12 / SSM 13 – 18 to store the following 12 stations. LOCAL SEEK*2 ON: Searches only stations with good reception. ; OFF: Cancels.

• Settings made are applicable only to the selected source/station. Once you change the source/station, you need to make the settings again. IF BAND AUTO: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain. MONO ON: Improves the FM reception, but the stereo effect will be lost. ; OFF: Cancels. NEWS-STBY*2 ON: The unit will temporarily switch to News Programme if available. ; OFF: Cancels. REGIONAL*2 ON: Switches to another station only in the specific region using the “AF” control. ; OFF: Cancels. AF SET*2 ON: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor. ; OFF: Cancels. TI SET*2 ON: Allows the unit to temporarily switch to Traffic Information if available (“TI” lights up). ; OFF: Cancels. PTY SEARCH*2 Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in. Use a portable audio player 1 Connect a portable audio player (commercially available).

3.5 mm stereo mini plug with “L” shaped connector

(commercially available) Auxiliary input jack Portable audio player 2 Select [ON] for [AUX] in [SRC SELECT]. ( 4) 3 Press repeatedly to select AUX. 4 Turn on the portable audio player and start playback. Use a 3-core plug head stereo mini plug for optimum audio output. PTY code: NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music), DOCUMENT *2 Only for FM source.

JS_JVC_KD_R961BT_E_EN_f.indd 8 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 28/8/2014 2:16:17 PM BLUETOOTH® BLUETOOTH — Connection Pair a Bluetooth device Supported Bluetooth profiles – Hands-Free Profile (HFP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) Supported Bluetooth codecs – Sub Band Codec (SBC) – Advanced Audio Coding (AAC) Connect the microphone Rear panel Microphone (supplied) Microphone input jack Adjust the microphone angle Secure using cord clamps (not supplied) if necessary. When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device. 1 Press to turn on the unit. 2 Search and select “JVC UNIT” on the Bluetooth device. “BT PAIRING” flashes on the display.

• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN) code immediately after searching.
• Refer also to the manual supplied with your Bluetooth device. 3 Perform (A) or (B) depending on what scrolls on the display. For some Bluetooth devices, pairing sequence may vary from the steps described below. (A) “[Device Name]” “XXXXXX” “VOL – YES” “BACK – NO” “XXXXXX” is a 6-digit passkey randomly generated during each pairing. Ensure that the passkey which appears on the unit and Bluetooth device is the same. Press the volume knob to confirm the passkey. Operate the Bluetooth device to confirm the passkey. (B) “[Device Name]” “VOL – YES” “BACK – NO” Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. You can change to a desired PIN code before pairing. ( 13)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. “PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the Bluetooth connection is established.
• Up to five devices can be registered (paired) in total.
• Only one Bluetooth device can be connected at any time.
• This unit supports Secure Simple Pairing (SSP).
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, 13, [DELETE PAIR].
• When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed the device name. Automatic pairing request is activated only if: – Bluetooth function of the connected devcie is turned on. – [AUTO CNNT] is set to [ON]. ( 13) – JVC MUSIC PLAY application is installed on the Android device. ENGLISH JS_JVC_KD_R961BT_E_EN_2.indd 9 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

7/8/2014 1:45:08 PM BLUETOOTH® BLUETOOTH — Mobile phone Improve the voice quality While talking on the phone.... 1 Press and hold 2 Turn the volume knob to make a selection (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit. To return to the previous setting item, press

Receive a call When there is an incoming call: – All the buttons flash. – The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 11) During a call: – The buttons and display illuminate according to the settings made for [COLOR]. ( 17) – If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected. Default: XX

On the faceplate On the remote control Answer a call Press Reject a call Press and hold knob. or the volume Press and hold

Adjust the phone volume [00] to [50] (Default: [15]*) Turn the volume knob during a call.

• This adjustment will not affect the volume of the other sources.

Switch between handsfree and private talk modes Press the volume knob during a call.

• Operations may vary according to the connected Bluetooth mobile phone.

or the volume knob. Press MIC LEVEL –10 — +10 (–4): The sensitivity of the microphone increases as the number increased. NOISE RDCT –5 — +5 (0): Adjust the noise reduction level until the least noise is being heard during a phone conversation. ECHO CANCEL –5 — +5 (0): Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.

• Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.

JS_JVC_KD_R961BT_E_EN_ff.indd 10 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 29/9/2014 4:17:53 PM BLUETOOTH® Make the settings for receiving a call to enter Bluetooth mode. 1 Press 2 Turn the volume knob to make a selection (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected or activated. To return to the previous setting item, press Default: XX SETTINGS AUTO ANSWER 01 SEC — 30 SEC: The unit answers incoming call automatically in the selected time (in seconds). ; OFF: Cancels. Make a call You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature. 1 Press to enter Bluetooth mode. 2 Turn the volume knob to make a selection (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. To return to the previous setting item, press RECENT CALL 1 Press the volume knob to select a name or a phone number.

• “>” indicates call received, “<“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number. 2 Press the volume knob to call. PHONEBOOK 1 Press to select the desired letter (A to Z, 0 to 9, and OTHERS).
• “OTHERS” appears if the first character is other than A to Z, 0 to 9. 2 Turn the volume knob to select a name, then press the knob. 3 Turn the volume knob to select a phone number, then press the knob to call.
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.) ENGLISH JS_JVC_KD_R961BT_E_EN_1.indd 11 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

23/7/2014 1:45:15 PM BLUETOOTH® DIAL NUMBER VOICE 1 Turn the volume knob to select a number (0 to 9) or character ( , #, 2 Press to move the entry position. Repeat steps 1 and 2 until you finish entering the phone number. 3 Press the volume knob to call. Speak the name of the contact you want to call or the voice command to control the phone functions. ( Make a call using voice recognition) Make a call using voice recognition to activate the connected phone. 1 Press and hold 2 Speak the name of the contact you want to call or the voice command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of iPhone. Delete a contact to enter Bluetooth mode. 1 Press 2 Turn the volume knob to select [RECENT CALL], then press the knob. 3 Turn the volume knob to select a contact. 4 Press and hold to enter delete mode. 5 Turn the volume knob to select [DELETE] or [DELETE ALL], then press the knob. DELETE: Selected name or phone number in step 3 is deleted. DELETE ALL: All names or phone numbers in [RECENT CALL] in step 2 is deleted. 6 Turn the volume knob to select [YES], then press the knob.
• To return to the previous setting item, press

• Not applicable for mobile phone that supports PBAP. Settings in memory Store a contact in memory You can store up to 6 contacts into the number buttons (1 to 6). 1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK], or [DIAL NUMBER], then press the knob. 3 Turn the volume knob to select a contact or enter a phone number. If a contact is selected, press the volume knob to show the phone number. 4 Press and hold one of the number buttons (1 to 6). “MEMORY P(selected preset number)” appears when the contact is stored. To erase a contact from the preset memory, select [DIAL NUMBER] in step 2 and store a blank number. Make a call from memory to enter Bluetooth mode. 1 Press 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call. “NO PRESET” appears if there is no contacts stored. Bluetooth mode settings 1 Press and hold 2 Turn the volume knob to select [BLUETOOTH], then press the knob. 3 Turn the volume knob to make a selection ( 13), then press the knob. 4 Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item. to exit. To return to the previous setting item, press

JS_JVC_KD_R961BT_E_EN_2.indd 12 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 7/8/2014 2:50:55 PM BLUETOOTH® Default: XX PHONE*1 AUDIO*1 Selects the phone or audio device to connect or disconnect. “ ” appears in front of the device name when connected. APPLICATION*1 Shows the connected phone name using the JVC Smart Music Control *2 app. “ ” appears in front of the device name when connected. DELETE PAIR 1 Turn the volume knob to select a device to delete, then press the knob. 2 Turn the volume knob to select [YES] or [NO], then press the knob. SET PINCODE (0000) Changes the PIN code (up to 6 digits). 1 Turn the volume knob to select a number. 2 Press to move the entry position. Repeat steps 1 and 2 until you finish entering the PIN code. 3 Press the volume knob to confirm. AUTO CNNCT ON: The unit automatically reconnect when the last connected Bluetooth device is within range. ; OFF: Cancels. AUTO PAIR ON: The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/ Android device) when it is connected through USB input terminal. Depending on the operating system of the connected device, this function may not work. ; OFF: Cancels. INITIALIZE YES: Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.). ; NO: Cancels. INFORMATION MY BT NAME: Displays the unit name (JVC UNIT). ; MY ADDRESS: Shows address of this unit. *1 You can only connect another Bluetooth device by disconnecting the connected Bluetooth device first. “ ” disappears when disconnected. *2 JVC Smart Music Control is designed to view JVC car receiver status and perform simple control operations on Android smart phones. For JVC Smart Music Control operations, visit JVC website: <http://www.jvc.net/cs/car/>. Bluetooth compatibility check mode You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired. 1 Press and hold “BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW USING PHONE” “PIN IS 0000” scrolls on the display. 2 Search and select “JVC UNIT” on the Bluetooth device within 3 minutes. 3 Perform (A), (B) or (C) depending on what appears on the display. (A) “PAIRING” “XXXXXX” (6-digit passkey): Ensure that the same passkey appears on the unit and Bluetooth device, then operate the Bluetooth device to confirm the passkey. (B) “PAIRING” “PIN IS 0000”: Enter “0000” on the Bluetooth device. (C) “PAIRING”: Operate the Bluetooth device to confirm pairing. After pairing is successful, “PAIRING OK” “[Device Name]” appears and Bluetooth compatibility check starts. If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device to allow phonebook access to continue. The connectivity result flashes on the display. “PAIRING OK” and/or “H.FREE OK”*1 and/or “A.STREAM OK”*2 and/or “PBAP OK”*3 : Compatible *1 Compatible with Hands-Free Profile (HFP) *2 Compatible with Advanced Audio Distribution Profile (A2DP) *3 Compatible with Phonebook Access profile (PBAP) After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.
• To cancel, press and hold to turn off the power, then turn on the power again. ENGLISH JS_JVC_KD_R961BT_E_EN_2.indd 13 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

8/8/2014 4:21:18 PM AUDIO SETTINGS BLUETOOTH® BLUETOOTH — Audio Audio player via Bluetooth repeatedly to select BT AUDIO (or press SOURCE 1 Press

On the faceplate On the remote control 4 Turn the volume knob to make a selection, Playback / pause Press Press Select group or folder Press

Press Reverse / Fast-forward Press and hold Repeat play repeatedly. Press

TRACK RPT, ALL RPT, RPT OFF

Random play repeatedly. Press

[USER2], then press the knob. then press the knob. For settings, refer to step 2 of [EASY EQ]. ( 15)

3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. to exit. To return to the previous setting item, press

Operations and display indications may differ according to their availability on the connected device.

Q FIX Q FIX) AUDIO BASS BOOST +01 / +02: Selects your preferred bass boost level. ; OFF: Cancels. LOUD 01 / 02: Boosts low or high frequencies to produce a well-balanced sound at low volume. ; OFF: Cancels. SUB.W LEVEL *1 SPK-OUT *2 00 to +06 (+03): Adjusts the output level of the subwoofer connected via speaker lead. ( 16) PRE-OUT *3 *4 –08 to +08 (00): Adjusts the output level of the subwoofer connected to the lineout terminals (REAR/SW) through an external amplifier. ( 16) SUB.W *3 *4 ON / OFF: Turns on or off the subwoofer output. SUB.W LPF *1 THROUGH: All signals are sent to the subwoofer. ; LOW 55HZ / MID 85HZ / HIGH 120HZ: Audio signals with frequencies lower than 55 Hz/ 85 Hz/ 120 Hz are sent to the subwoofer. ENGLISH JS_JVC_KD_R961BT_E_EN_20_1.indd 15 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

20/10/2014 11:08:56 AM AUDIO SETTINGS SUB.W PHASE *1 REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for [SUB.W LPF].) HPF (For KD-R961BT) OFF: All signals are sent to the front/rear speakers. ; LOW 100HZ / MID 120HZ / HIGH 150HZ: Audio signals with frequencies lower than 100 Hz/ 120 Hz/ 150 Hz are cut off from the front/rear speakers. FADER R06 — F06 (00): Adjusts the front and rear speaker output balance. BALANCE *5 L06 — R06 (00): Adjusts the left and right speaker output balance. VOL ADJUST –05 — +05 (00): Presets the volume adjustment level of each source (compared to the FM volume level). Before adjustment, select the source you want to adjust. (“VOL ADJ FIX” appears if FM is selected.) AMP GAIN LOW POWER: Limits the maximum volume level to 30. (Select if the maximum power of each speaker is less than 50 W to prevent damaging the speakers.) ; HIGH POWER: The maximum volume level is 50.

(Digital Track Expander) ON: Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression. ; OFF: Cancels.

Selects the appropriate setting to get the desired output.

Subwoofer output Connection via speaker leads ( 25)

Displayed only when [SUB.W] is set to [ON]. ( 15) *2 Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W].

• For unit with 3-pair lineout terminals: Displayed only when [SPK/PRE OUT] is set to [REAR/REAR] or [SUB.W/SUB.W]. *4 For unit with 1-pair lineout terminals: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W]. *5 This adjustment will not affect the subwoofer output.

Subwoofer output Rear speaker lead Setting L (left) R (right) REAR/REAR Rear speakers output Rear speakers output

Subwoofer output (Mute) If [SUB.W/SUB.W] is selected: – [HIGH 120HZ] is selected in [SUB.W LPF] and [THROUGH] is not available. – [R01] is selected in [FADER] and selectable range is [R06] to [00]

DISP ZONE: DAY: 31 ; NIGHT: 12) SCROLL *2 ONCE: Scrolls the display information once. ; AUTO: Repeats scrolling at 5-second intervals. ; OFF: Cancels. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item. to exit. To return to the previous setting item, press

COLOR (for KD-R961BT) 4 Press PRESET Default: XX DISPLAY DIMMER Selects the display and button illumination adjusted in the [BRIGHTNESS] setting. OFF: Selects the day adjustments. ; ON: Selects the night adjustments. ; DIMMER TIME: Adjusts the dimmer on and off time. Turn the volume knob to adjust the [ON] time, then press the knob. Turn the volume knob to adjust the [OFF] time, then press the knob. (Default: [ON]: 18:00 or 6:00 PM [OFF]: 6:00 or 6:00 AM) AUTO: Changes between the day and night adjustments when you turn off or on the car headlights. *1 For KD-R961BT, the display and button colors change according to the settings made on [COLOR]. You can select a color for [ALL ZONE], [ZONE 1], [DISP ZONE], or [ZONE 2] separately. For [ALL ZONE], you can also select a color pattern. Default color: ALL ZONE: [COLOR 06], ZONE 1: [COLOR 06],

DISP ZONE: [COLOR 01], ZONE 2: [COLOR 27]

1 Select a zone for setting. ( Illustration on left) 2 Select a color for the selected zone.

• COLOR 01 to COLOR 29
• USER: The color you have created for [DAY COLOR] or [NIGHT COLOR] is shown.
• COLOR FLOW01 to COLOR FLOW03: Color changes at different speeds.
• GROOVE/ TECHNO/ EMOTION/ RELAX/ SPECTRUM/ SWEEP/ POP: The selected color pattern is shown.*3 (Selectable only when [ALL ZONE] is selected in step 1.) *1 The illumination control wire connection is required. ( 25) *2 Some characters or symbols will not be shown correctly (or will be blanked). *3 If one of these color pattern is selected, the [ZONE 1], [DISP ZONE], [ZONE 2] illumination color will change to the default color. ENGLISH JS_JVC_KD_R961BT_E_EN_20_1.indd 17 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

20/10/2014 11:09:31 AM DISPLAY SETTINGS MORE INFORMATION DAY COLOR About discs and audio files

• This unit can only play the following CDs: NIGHT COLOR COLOR GUIDE Store your own day and night colors for different zone. 1 Select a zone for setting. ( 17) 2 RED / GREEN / BLUE: Select a primary color. 3 00 to 31: Select the level. Repeat steps 2 and 3 for all the primary colors.
• Your setting is stored to [USER] in [PRESET].
• If [00] is selected for all primary colors for [DISP ZONE], nothing appears on the display. ON: Changes the button, display, USB input terminal and auxiliary input jack illumination when settings are performed on menu and list search. Display zone will automatically change depending on volume level. ; OFF: Cancels. [NIGHT COLOR] or [DAY COLOR] is changed by turning on or off your car’s headlight.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped during playback.
• Unplayable discs: - Discs that are not round. - Discs with coloring on the recording surface or discs that are dirty. - Recordable/ReWritable discs that have not been finalized. - 8 cm CD. Attempting to insert using an adapter may cause malfunction.
• DualDisc playback: The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product cannot be recommended.
• Playable files: - File extensions: MP3 (.mp3), WMA (.wma), AAC (.m4a) - Bit rate: MP3: 8 kbps — 320 kbps WMA: 32 kbps — 192 kbps AAC: 8 kbps — 320 kbps - Sampling frequency: MP3: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz, 16 kHz, 12 kHz, 11.025 kHz, 8 kHz WMA: 8 kHz — 48 kHz AAC: 8 kHz — 48 kHz - Variable bit rate (VBR) files.
• Maximum number of characters for file/folder name: It depends on the disc format used (includes 4 extension characters—<.mp3>, <.wma> or <.m4a>). - ISO 9660 Level 1 and 2: 32 characters - Romeo: 32 characters - Joliet: 32 characters - Windows long file name: 32 characters

JS_JVC_KD_R961BT_E_EN_1.indd 18 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 23/7/2014 1:45:18 PM MORE INFORMATION About USB devices

• This unit can play MP3/WMA/AAC/WAV files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
• The maximum number of characters for: - Folder names: 64 characters - File names: 64 characters - MP3 Tag: 64 characters - WMA Tag: 64 characters - AAC Tag: 64 characters - WAV Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders (999 files per folder including folder without unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1 A. About iPod/iPhone Made for - iPod touch (2nd, 3rd, 4th, and 5th generation) - iPod classic - iPod nano (3rd, 4th, 5th, 6th, and 7th generation) - iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• It is not possible to browse video files on the “Videos” menu in [HEAD MODE].
• The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone.
• If some operations are not performed correctly or as intended, visit: <http://www.jvc.net/cs/car/>. About Bluetooth
• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit.
• This unit may not work with some Bluetooth devices.
• Signal conditions vary, depending on the surroundings.
• For more information about Bluetooth, visit the following JVC website: <http://www.jvc.net/cs/car/>. About JVC Playlist Creator and JVC Music Control
• This unit supports the PC application JVC Playlist Creator and AndroidTM application JVC Music Control.
• When you play audio file with song data added using the JVC Playlist Creator or JVC Music Control, you can search for audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site: <http://www.jvc.net/cs/car/>. Available Cyrillic letters Available characters Display indications About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory (AOA) 2.0.
• If the Android device supports both mass storage class device and AOA 2.0, this unit always playback via AOA 2.0 as priority.
• For more information and the latest compatible list, see: <http://www.jvc.net/cs/car/>. ENGLISH JS_JVC_KD_R961BT_E_EN_1.indd 19 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

23/7/2014 1:45:18 PM TROUBLESHOOTING MORE INFORMATION Change the display information Press repeatedly. Playing time Day/Clock Disc name*3 Album title/Artist*4 Track title*5 Folder/file name*6 (back to the beginning) *3 Only for CD-DA: If not recorded, “NO NAME” appears. *4 Only for MP3/WMA/AAC/WAV files: If not recorded, “NO NAME” appears. *5 If not recorded, “NO NAME” appears. *6 Only for MP3/WMA/AAC/WAV files. USB-IPOD/ Playing time Day/Clock Album title/Artist*7 USB-ANDROID to the beginning) *7 If not recorded, “NO NAME” appears. AUX BT AUDIO Playing time Day/Clock Album title/Artist*8 to the beginning) *8 If not recorded, “UNKNOWN” appears. (back Day/Clock Track title*8

• Adjust the volume to the optimum level.
• Check the cords and connections. “MISWIRING CHECK

appears. Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again. “PROTECTING SEND SERVICE” appears. Send the unit to the nearest service center. Source cannot be selected. (back CD / USB / iPod AUX Track title*7 Remedy Sound cannot be heard. Title*1*2 General CD or USB Station name (PS)*1 Frequency Program type (PTY)*1*2 Day/Clock (back to the beginning) *1 For FM Radio Data System stations only. *2 If unavailable, “NO PTY” / “NO TEXT” appears. Radio FM or AM Symptom

• Radio reception is poor.
• Static noise while listening to the radio. Check the [SRC SELECT] setting. ( 4)
• Connect the antenna firmly.
• Pull the antenna out all the way. Disc cannot be ejected. Press and hold to forcibly eject the disc. Be careful not to drop the disc when it is ejected. “IN DISC” appears. Make sure nothing is blocking the loading slot when you eject the disc. “PLEASE” and “EJECT” appear alternately. Press , then insert the disc correctly. Playback order is not as intended. The playback order is determined by the file name (USB) or the order in which files were recorded (disc). Elapsed playing time is not correct. This depends on the recording process earlier. “NOT SUPPORT” appears and track skips. Check whether the track is a playable format. ( 18) “READING” keeps flashing. • Do not use too many hierarchical levels and folders.
• Reload the disc or reattach the USB device. “CANNOT PLAY” flashes and/or connected device cannot be detected.

• Check whether the connected device is compatible with this unit and ensure the files are in supported formats. ( 18)
• Reattach the device.

JS_JVC_KD_R961BT_E_EN_2.indd 20 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 8/8/2014 4:21:25 PM TROUBLESHOOTING Remedy Symptom Remedy The iPod/iPhone does not • Check the connection between this unit and iPod/iPhone. turn on or does not work. • Detach and reset the iPod/iPhone using hard reset. No Bluetooth device is detected.

• Search from the Bluetooth device again.
• Reset the unit. ( 3) Correct characters are not displayed. Pairing cannot be made.

• Make sure you have entered the same PIN code to both the unit and Bluetooth device.
• Delete pairing information from both the unit and the Bluetooth device, then perform pairing again. ( 9) Echo or noise occurs.

• Adjust the microphone unit’s position. ( 9)
• Check the [ECHO CANCEL] setting. ( 10) Phone sound quality is poor.

• Reduce the distance between the unit and the Bluetooth device.
• Move the car to a place where you can get a better signal reception. Sound is being interrupted or skipped during playback of a Bluetooth audio player.

• Reduce the distance between the unit and the Bluetooth audio player.
• Turn off, then turn on the unit and try to connect again.
• Other Bluetooth devices might be trying to connect to the unit. The connected Bluetooth audio player cannot be controlled.

• Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.)
• Disconnect and connect the Bluetooth player again. This unit can only display uppercase letters, numbers, and a limited number of symbols. Uppercase Cyrillic letters can also be displayed if [РУССКИЙ] is selected. ( 4)

• Sound cannot be heard • Reconnect the Android device.
• If in [AUDIO MODE], launch any media player application during playback.
• Sound output only from on the Android device and start playback. the Android device.
• If in [AUDIO MODE], relaunch the current media player application or use another media player application.
• Restart the Android device.
• If this does not solve the problem, the connected Android device is unable to route the audio signal to unit. ( 19)
• Make sure JVC MUSIC PLAY APP is installed on the Android device. ( 5)
• Reconnect the Android device and select the appropriate control mode. ( 6)
• If this does not solve the problem, the connected Android device does not support [AUTO MODE]. ( 19) “NO DEVICE” or “READING” keeps flashing.

• Switch off the developer options on the Android device.
• Reconnect the Android device.
• If this does not solve the problem, the connected Android device does not support [AUTO MODE]. ( 19) ANDROID Cannot playback at [AUTO MODE]. Playback is intermittent or sound skips. “CANNOT PLAY” Bluetooth® CD / USB / iPod Symptom “PAIRING FULL” The number of registered devices has reached its limit. Retry after deleting an unnecessary device. ( 13, DELETE PAIR) “PLEASE WAIT” The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again. Turn off the power saving mode on the Android device.
• Make sure Android device contains playable audio files.
• Reconnect the Android device.
• Restart the Android device. ENGLISH JS_JVC_KD_R961BT_E_EN_1.indd 21 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

87.5 MHz — 108.0 MHz (50 kHz step)

FOUND” The unit failed to search for the registered Bluetooth devices during [AUTO CNNCT]. Turn on Bluetooth from your device and connect manually. ( 13) Usable Sensitivity (S/N = 26 dB) “NOT SUPPORT” The connected phone does not support Voice Recognition feature. Frequency Response (±3 dB) 30 Hz — 15 kHz Signal-to-Noise Ratio (MONO) 64 dB Stereo Separation (1 kHz)

50 μV “ERROR” Try the operation again. If “ERROR” appears again, check if the device supports the function you have tried.

Reset the unit and try the operation again. If “H/W ERROR” appears again, consult your nearest service center.

Quieting Sensitivity (DIN S/N = 46 dB)

AM Frequency Range Usable Sensitivity (S/N = 20 dB) CD player If you still have troubles, reset the unit. ( 3) Laser Diode GaAIAs Digital Filter (D/A) 8 times over sampling Spindle Speed 500 rpm — 200 rpm (CLV) Wow & Flutter Below measurable limit Frequency Response (±1 dB) 20 Hz — 20 kHz Total Harmonic Distortion (1 kHz)

Signal-to-Noise Ratio (1 kHz) 105 dB Dynamic Range 90 dB Channel Separation 85 dB MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio AAC Decode AAC-LC “.m4a” files

Output Power +4 dBm (MAX), 0 dBm (AVE) Power Class 2 Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Pairing SSP (Secure Simple Pairing) Profile HFP1.6 (Hands-Free Profile) A2DP (Advanced Audio Distribution Profile) AVRCP1.4 (Audio/Video Remote Control Profile) PBAP (Phonebook Access Profile) SPP (Serial Port Profile)

Maximum Current Consumption 10 A Operating Temperature Range 0°C to +40°C Installation Size (W × H × D) 182 mm × 53 mm × 158 mm Weight

20/10/2014 11:09:43 AM INSTALLATION / CONNECTION Warning

• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation. Installing the unit (in-dash mounting) Do the required wiring. ( 25) Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50 W. If the maximum power of the speakers is lower than 50 W, change the [AMP GAIN] setting to avoid damaging the speakers. ( 16)
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with one that has the same rating. Basic procedure 1 Remove the key from the ignition switch, then disconnect the Hook on the top side Orientate the trim plate as illustrated before fitting. Dashboard of your car Bend the appropriate tabs to hold the sleeve firmly in place. When installing without the mounting sleeve How to remove the unit Use only the specified screws. Using wrong screws might damage the unit. Flat or round head screws (not supplied) 5 × 8 mm terminal of the car battery. 2 Connect the wires properly. See Wiring connection. ( 25) 3 Install the unit to your car. See Installing the unit (in-dash mounting). 4 Connect the terminal of the car battery. 5 Reset the unit. ( 3) Pocket Bracket (not supplied)

JS_JVC_KD_R961BT_E_EN_1.indd 24 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 23/7/2014 1:45:20 PM Wiring connection KD-R961BT Rear output KD-R864BT/ KD-R862BT/ KD-R861BT Front output Subwoofer output Signal cord (not supplied) Rear/subwoofer output Remote wire (not supplied) *1 Firmly connect the ground wire of the amplifier to the car’s chassis to avoid To Blue/white wire of damaging the unit. the wiring harness (D) JVC Amplifier *1 Part list for installation (A) Faceplate Fuse (10 A) Antenna terminal To the steering wheel remote control adapter For some VW/Audi or Opel (Vauxhall) automobiles You may need to modify the wiring of the supplied power cord (D) as illustrated. If the unit does not turn on with modified wiring 1, use modified wiring 2 instead. Y: Yellow R: Red Microphone input jack ( 9) ( or ) Modified wiring 2 (B) Trim plate STEERING WHEEL REMOTE If your car does NOT have an ISO terminal Original wiring Modified wiring 1 ISO connector Light blue/yellow *2 Custom wiring harness (separately purchased) IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is recommended for connection. Pin Color and function A4 Yellow : Battery A5 Blue/White : Power control A6 Orange/white : Car light control switch A7 Red : Ignition (ACC) A8 Black : Earth (ground) connection B1 Purple ª : Rear speaker (right) B2 Purple/black · B3 Gray ª : Front speaker (right) B4 Gray/black · B5 White ª : Front speaker (left) B6 White/black · B7 Green ª : Rear speaker (left) *3 B8 Green/black · *3 You can also connect a subwoofer speaker directly without an external subwoofer amplifier. For setting, 16. (C) Mounting sleeve (D) Wiring harness (E) Extraction key ENGLISH JS_JVC_KD_R961BT_E_EN_20_1.indd 25 Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm)

3/9/2014 11:35:55 AM

“BT DEVICE NOT FOUND”

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Android is trademark of Google Inc.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners. © 2014 JVC KENWOOD Corporation JS_JVC_KD_R961BT_E_C_00.indd 2 0914DTSMDTJEIN Data Size: Book Size: B6L (182 mm x 128 mm) B6L (182 mm x 128 mm) 22/7/2014 3:27:58 PM