FBHD 900 PT X - Basket Fulgor Milano - Free user manual and instructions

USER MANUAL FBHD 900 PT X Fulgor Milano

The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure they do not play with the appliance.

• The exhausted air can't be conveyed through or into a duct used to let out fumes from appliances fed by energy other than electric power (eg. centralized heating, radiators, water-heaters, etc.).
• To evacuate the air outlet, please comply with the pertaining rules given by competent authorities.
• Provide the room with an adequate aeration when a cooker hood and appliances fed by energy other than electric power (gas-, oil-, or coal- stoves, etc.) are used simultaneously. The cooker hood, when evacuating the exhausted air, could generate a negative pressure in the room.

• The cooker surface and the inferior part of the cooker hood must be at a minimum distance of 65 cm.

• When performing the electrical connections on the appliance, please make sure that the current-tap is provided with earth connection and that voltage values correspond to those indicated on the label placed inside the appliance itself.

Before carrying out any cleaning or maintaining operations, the appliance needs to be removed from the electric grid.

If the appliance is not provided with a non-separable flexible cable and plug, or with another device ensuring omnipolar disconnection from the grid, with an opening distance between the contacts of at least 3mm then such disconnecting devices must be supplied within the fixed installation. If the fixed appliance is endowed with a supply cord and a plug, the appliance has to be put in a place where the plug can be reached easily.

• The use of materials which can burst into flames should be avoided in close proximity of the appliance. When frying, please pay particular attention to fire risk due to oil grease. Being highly inflammable, fried oil is especially dangerous. Do not use un-covered electric grills. In order to avoid possible fire risk, all instructions for grease-filter cleaning and for removing eventual grease deposits should be strictly followed.

Before installing the appliance, make sure that none of the parts is damaged in any way. In case of damaged parts, contact your retailer and do not proceed with installation.

Read all of the following instructions with care before installing the appliance.

• Use an air outlet pipe of the shortest possible length.
• Limit the number of pipe bends.
• Use a material approved by standards and regulations.
• Avoid any sudden changes in pipe section (recommended constant diameter: 150mm or equal surface area).

For failure to comply with the above-mentioned instructions, the supplier will disclaim any liability for problems concerning flow rate or noise and will not grant any warranty.

USES

The appliance is already arranged both for filtering and for suction performances.

• In its filtering version the air and fumes conveyed by the appliance are depured both by a grease filter and by an active coal filter.

In its exhausting version fumes are directly conveyed outside, through an evacuation duct connected with the superior part of the wall or the ceiling.

In this case, it is not necessary to use a charcoal filter.

INSTALLATION FBHD 700 PT X - FBHD 900 PT

Before the installation, in order to avoid any damage, remove the grease filter with the proper handle, rotating the filter downwards and removing it.

Before removing the grease filter, remove the perimetrical panel turning it downwards as per Fig. 1.

Make a hole taking care of the following dimensions:

252mm x 649mm for FBHD 700 PT X

252mm x 849mm for FBHD 900 PT X

Should the depth of the cabinet be more than 380mm , fixing levers (fig. 4-5) can be used.

In case of cabinets with lower depth, use the fixing screws as shown in fig. 6.

Adjust the position of the lateral springs considering the thickness of the material you are fixing the unit on (Fig.2).

Connect the appliance with the electric mains.

Insert the unit from below, making sure that the springs, previously adjusted(Fig. 2), are strong enough to keep the product fixed (fig. 3).

Insert the four blocking levers and fix them using the screws, as showed in fig. 4 and fig. 5.

Mount the grease filter previously removed.

Reinstall the perimetal panel.

WORKING

(Fig. 7)

A: Light switch on/off
B: Motor switch on/off (1st rate level)
C: 2^nd rate level switch
D: 3^rd rate level switch
E: 4^th rate level switch
F: 10 - minute timer.

All products are endowed with an electronic device which allows the automatic switching off after 4 hours working from the last operation.

TIMING

As a result of the new EU65 "Energy label" and EU66 "Ecodesign" regulations issued by the European Commission, which came into force as from January 1^st , 2015, our products have been adapted to comply with these new requirements.

All of the models complying with the energy label requirements are equipped with new electronics including a timer device for suction speeds control, when the air capacity exceeds 650m^3 /h

Internal motor models, with maximum air capacity higher than 650m^3 /h are equipped with a timer device that automatically switches the suction speed from 4 th to 3^rd speed, after 5 minutes operation.

External motor models are equipped with remote motors that, as for internal motor versions, include a timer device that switches down the suction speed when it exceeds 650m^3 /h . (See External Motors Instructions).

Remote motors, whose air capacity exceeds 650m^3 /h at both 4^th and 3^rd speed, will have the following by default timer control functions: the suction speed is automatically switched from 4^th to 2^nd speed, after 6 minutes operation.

If the appliance is working at 3^rd speed, it is automatically switched to 2^nd speed, after 7 minutes operation. Operation speeds can also be changed during operation.

The energy consumption of the appliance in stand - by mode is lower than 0.5W.

MAINTENANCE

An accurate maintenance guarantees good functioning and long-lasting performance.

Particular care is due to the grease filter panel.

Before removing the grease filter, it is necessary to open the light panel by rotating it downwards as per Fig. 1.

The grease filter needs cleaning by regular handwashing or in dishwashers every two months at least or depending on its use.

• In case the appliance is used in its filtering version, the active coal filter

needs to be periodically replaced. The coal filter can be removed by removing the grease filter first, and by pulling its special plastic tongue until it is un-fastened from its slot. Reinsert the coal filter by operating in the opposite way. The coal filter needs replacing depending on the use, at least once every six months.

To clean the appliance, tepid water and neutral detergent are recommended, while abrasive products should be avoided.

Replacement of LED Lamps

If there is no access to the rear, use a tool with a fine tip and insert it between the lamp and the canopy of the hood, where the two retaining tabs are located; then, press and release the lamp (Fig. 8).

Attention

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. This appliance is marked according to the European directive 2012/19/EC on waste electrical and electronic equipment (WEEE).