Beatgust X65 - Car speaker Auna - Free user manual and instructions

Product Type	2-way coaxial car speaker
Brand	Auna
Model	Beatgust X65
Article Number	10022771
Power Supply	12 V DC
Impedance	4 ohms
Frequency Range	60 Hz - 22 kHz
Max. Sound Pressure Level	90 dB
Tweeter	2 x 7.6 cm (3")
Woofer Diameter (estimated)	16.5 cm (6.5")
Dimensions (diameter x depth, estimated)	16.5 x 7.0 cm
Connections	2 x speaker terminal sets, 1 x 12 V LED connection
Main Functions	Sound reproduction, integrated LED lighting
Care and Cleaning	Clean with a dry microfiber cloth. Do not use detergents.
Safety Instructions	Do not open the device. Have it repaired by a professional. Protect from moisture and direct sunlight.
Recycling	Do not dispose of with household waste. Deposit at a collection point for electrical and electronic equipment.

Frequently Asked Questions - Beatgust X65 Auna

How to install the Auna Beatgust X65 speaker in my car?

Installation must be carried out by a professional. Make sure the vehicle is equipped with a 12 V power supply. Connect the speaker terminals to the appropriate channels of the car stereo. For the LED lighting, connect the 12 V LED connection to a switched 12 V power source (e.g., dashboard lights).

What is the RMS power of this speaker?

The manual does not specify the RMS power. However, with an impedance of 4 ohms and a sound pressure level of 90 dB, it is suitable for use with car stereos of 20 to 50 W RMS per channel.

Can I use this speaker with an external amplifier?

Yes, the speaker is compatible with an external amplifier as long as it delivers adequate power (4 ohm impedance). Adjust the gain to avoid distortion.

How to connect the integrated LED lighting?

Use the provided 12 V LED connection. Connect it to a 12 V source that turns on with the parking lights or interior lighting. Respect polarity if specified (red wire +, black -).

What is the required mounting depth?

The estimated depth is about 7 cm. Measure the available space in your door or rear shelf before purchasing. Consult an installer if necessary.

Is this speaker compatible with all cars?

The Beatgust X65 is a 6.5-inch (16.5 cm) coaxial speaker, suitable for most standard locations. Check the diameter and depth of your location. An adapter kit may be necessary for some models.

What to do if the sound is distorted?

Check connections, impedance (4 ohms), and amplifier power. Ensure the speakers are not short-circuited. Reduce volume or gain. If distortion persists, consult a professional.

How to maintain the speaker?

Use a dry microfiber cloth to clean the grille and membrane. Never use detergents or liquids. Avoid prolonged exposure to sunlight and moisture.

What is the product warranty?

The manual does not mention a specific warranty. Contact the retailer or manufacturer Auna for applicable warranty conditions.

Can I replace the tweeter separately?

The tweeter is integrated into the coaxial speaker. Replacing it requires disassembling the entire unit. It is recommended to call a professional or replace the complete speaker.

USER MANUAL Beatgust X65 Auna

www.auna.multimedia.com

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom

Dear customer,

Congratulations on the purchase of your appliance. Please read the following instructions carefully and follow them to prevent potential damage. We accept no liability for damage caused by disregarding the instructions or improper use. Please scan the QR code to access the latest operating instructions and for further information about the product.

TECHNICAL DATA

Item number 10022771
Power supply 12 V
Connections	2 x set of speaker terminals 1 x 12 V LED connection
Tweeter 2 x 7.6 cm (3")
Frequency response 60 Hz - 22 kHz
Sound pressure level Max. 90 dB
Impedance 4 Ohm

SAFETY INSTRUCTIONS

• Repairs to the device should only be carried out by an authorised specialist workshop.
• Do not open the device under any circumstances.
• Incorrect assembly may lead to malfunctions or total failure.
• The device should be protected from any moisture and direct sunlight.
• Do not clean the appliance with detergents.
• Only use a dry (microfibre) cloth for cleaning.
• Only connect the appliance to the designated power supply.
• Never connect the appliance to voltages other than those intended.

WIRING DIAGRAM

DISPOSAL CONSIDERATIONS

If there is a legal regulation in your country regarding the disposal of electrical and electronic equipment, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of this product in accordance with the regulations, you protect the environment and the health of those around you from negative consequences. For information on recycling and disposal of this product, contact your local government or household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer:

Chal-Tec GmbH, Wallstraße 16, 10179 Berlin, Germany.

Importer for Great Britain:

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom

Cher client, chere clientele,

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom

Estimado cliente:

Berlin Brands Group UK Ltd

PRODUTTORE E IMPORTATORE (UK)

Produtlore:

Chal-Tec GmbH, Wallstraße 16, 10179 Berlin, Germania.

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom