EG411VTUU - Range hood Atag - Free user manual and instructions

USER MANUAL EG411VTUU Atag

3D diagram of a mechanical component with a conical base and top assembly (no text or symbols)

ATAG

instructions for use/installation instructions

WS90..MM - WS12..MM - ES12..MM Waal

WS90..NM - WS12..NM - ES12..NM Dinkel

Diagram illustrating a waste sorting or sorting process with labeled components and a recycling symbol

afvoer

Technical diagram of a mechanical component with labeled parts and dimension lines

Technical diagram showing a mechanical assembly with a magnified inset view of a component (no text or symbols present)

kap ophangen

Technical diagram showing mechanical assembly steps with numbered components and directional arrows

NL 12NL 12

montage (vervolg)

Simple line drawing of a box with a hanging object and two diagonal lines above it (no text or symbols)

The extractor hood has been designed for domestic use and for the purposes stated. Atag extractor hoods are available in many different models, which fit elegantly into all interiors. The Atag range offers various types of hoods, some with built-in motors and others suitable for recirculation.

When you have read this manual, you will quickly be aware of all the facilities the appliance can offer you. You can read about safety and how you should look after the appliance. In addition you will find environmental tips and instructions that can help to save energy.

Keep the manual. Any later user of this appliance could benefit from them.

table of contentsintroduction

general 1 - 2

introduction 1

for your safety 2

instructions for use 3 - 7

lighting 3

fan 3-4

faults 5

how to keep the appliance looking good 6 - 7

installation instructions 8 - 14

installation 8 – 9

assembly 10 – 13

technical data 14

disposal of packaging and appliances 14

Please note!

Separate installation instructions are supplied for the Island models.

for your safety

please note

This appliance should be connected by a registered fitter. Damage arising from incorrect connection or incorrect fitting is not covered by the guarantee.

Disconnect the appliance before starting with cleaning or reparation. It is recommended that you do this by removing the plug from the socket or by setting the isolation switch to zero.

Never flambe under an extractor. The high flames can cause fire. Even if the ventilator is switched off.

When deep-frying, always keep a close watch.

If the appliance is used together with equipment which uses gas or other fuels, then a sufficient supply of fresh air must be ensured.

Switch the extractor hood on before starting to cook. After cooking, allow the extractor hood to continue to run for approx. 10 minutes. This can also be done automatically (see 'automatic continued running').

Clean the appliance regularly, as shown in 'maintenance'. This minimises the chance of a fire starting.

Switch off the electricity before replacing the light bulbs! Only use the same sort of light bulbs with the same Wattage.

In view of possible sharp edges on the chimney we advise you to wear working gloves when fitting the chimney.

lighting

1

2

3

4

ATAG

switching lighting on and off

Press the lighting button

The lighting comes on at its highest setting.

Press the button again and the lighting is dimmed.

Press the button for a third time and the lighting goes out. The indicator light in the button also goes out.

fan

The extractor hood comes on at the setting selected. The figure in the button lights up.

adjusting the extractor capacity

Press a button with a higher or lower value.

The figure in the button lights up.

intensive setting

Press the button.

The figure in the button lights up.

fan (continued)

1

2

3

4

ATAG

Press the button with the illuminated symbol.

The extractor hood switches off and the light of the symbol in the button goes out.

automatic continued operation

Choose the fan setting desired and press the button.

The symbol in the button lights up.

After approximately 10 minutes, the extractor hood switches back automatically and finally switches off. If the lighting was switched on during the automatic continued running, it will remain switched on.

cleaning the grease filter

If the grease filter indicator light comes on, the filter should be cleaned immediately.

Replace the filter after cleaning and erase the electronic memory by pressing the button for approx. 5 seconds. The indicator light goes out.

faults

Please check the following points which may solve the problem, before calling the service department.

If the connection cable is damaged, it should be replaced by the service department of the manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.

NB: Disconnect the appliance from the mains before starting any repairs, preferably by removing the plug from the socket or by setting the isolation switch to zero.

fault

Lighting does not work.

cause

Lamp defective.

solution

Pull the inner ring downwards using a screwdriver (see illustration).

NB:

Only use the same type of lamp with the wattage stated.

NB: the glass is loose! Pull the halogen lamp out of the fitting and replace it with a new 20 W halogen lamp (wall hoods) or 10 W halogen lamp (island hoods). Use a clean cloth to hold the new lamp.

Extractor hood makes a lot of noise.

Discharge duct too long or has too many bends.

Change the discharge duct (see installation instructions).

Motor defective.

Phone the Service department.

No extraction.

Motor or controls defective.

Phone the Service department.

Connection lead defective.

Phone the Service department.

maintenance

extractor hood

Clean the grease filters as soon as the grease filter indicator light comes on.

The stainless steel on the outside of the hood can be cleaned with soapy water and a damp cloth. The stainless steel will regain its shine if you occasionally use a stainless steel care product or polish. The polish imparts a dirt-resistant layer to the stainless steel. Always clean the stainless steel in the direction of polishing,

Never use abrasive cleaning agents (such as Vim, green scouring pads or other scourers) or polishing cleaning products (such as liquid scourers).

Never use caustic cleaning agents. These can cause stainless steel to discolour.

maintenance (continued)

removing/replacing grease filters

Remove the filters as follows: switch the fan and the lighting off.

Push the filter at the edge of the niche to the back and pull the front end down. You can now remove the filter from the hood.

The filter can only be put back into place in one way. Take note of the correct position of the filter (see illustration). Hold the filter in such a way that the covered part of the underside is at the centre rear. This is recognizable on the outside by the pattern with the smaller holes.

Put the filter back into place by first pushing the rear side into the holder. Then push the front upwards until it cannot go any further and let the filter slide forwards. The filter is now once again in place. Erase the electronic memory by pressing the button for approx. 5 seconds.

cleaning the grease filters

You can clean the grease filters in the dishwasher. Allow the filter to drain well - through the slits in the side - before putting it back.

replacing the carbon filter

Replace the carbon filter twice a year. This only applies to recirculation hoods.

Put the carbon filter in the place intended for it above the filters.

installation

some preliminary remarks

An extractor hood should be installed in accordance with national and local regulations. The minimum distance between the underside of the extractor hood and the hob should be 65 cm.

The appliance should be connected by a registered fitter. Damage arising from incorrect connection or incorrect fitting is not covered by the guarantee.

NB:

If an extractor hood and a heat source (for example, gas-, oil- or coal-fired cookers) which take air from the same room are in use at the same time, there is a possibility that the extractor hood will cause an underpressure in that room. The maximum permitted underpressure is 4 Pa, so that no combustion gases from the heat source can find their way back into the room. For this reason, an air supply is required - to provide a constant supply of fresh air to the room.

electrical connection

The extractor hood's plug should be accessible after fitting or the extractor hood should be isolated by a bipolar switch with 3 mm plug pins.

When making the electrical connections, make sure that the socket is earthed and that the voltage and frequency correspond to the values given on the data plate.

If the connection cable is damaged, it should be replaced by the service department of the manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.

installation (continued)

discharge

The discharge should not be connected to a duct which is also used for other purposes under any circumstances.

Bear in mind any local regulations concerning the ventilation of gas appliances.

The discharge may pass straight through the wall to the outside, provided that the wall opening is protected - by means of a grating - against rain, leaves, and the like getting in. The passage of the discharge may not be restricted by the wall grating by more than 20%.

We advise the use of as large a discharge duct as possible. A duct with a smaller diameter will have a low extraction capacity and produce higher noise levels.

Bends produce resistance. Make sure that the duct has a smooth run and has as few bends as possible. Draw the flexible pipe out as far as possible.

Before starting to drill, check that there are no installed pipes present.

The discharge stump has a diameter of 150 mm. It is best if the discharge pipe also has this diameter.

A reducing piece (150 mm to 125 mm) is supplied with the appliance for connection to a 125 mm discharge pipe.

transport protection device

The cooker hood comes with a transport protection device that has to be removed before installation. Remove the 4 screws at the rear of the motor module (see fig.) and detach the motor module from the cooker hood. Observe the assembly instructions on the following pages.

Diagram illustrating a waste sorting or sorting process with labeled components and a recycling symbol

assembly

building-in dimensions wall hood

6150-125 850-210 2.6 395 500 235 240 600 300 min 850 WG3/4X

a150/125 700-1065 160 235 240 530 900 min. 850 WG3/411

240 235 min 720 - max 1080 530 900-1200 80 WS9011MM WS1211MM

ø150/125 765-1125 235 240 150 530 900 min. 650 WG34V

min. 720 max. 1080 530 240 235 420 45 36 600 900 WS9611NM

min.745 - max.1105 230 235 420 59 48 680 1200 530 WS1211KM

assembly (continued)

installation wall hood

The most important dimensions are shown on the previous page. You can set the height of the telescopic pipe. Take the allowable tolerances into account. Position the discharge and the electrical connection in such a way that it will be easy to hook up the hood.

Remove the transport safety device prior to assembly, see page 9.

marking out and fitting fixing materials

Draw a vertical centre line on the wall (centre of the extractor hood).

Place the fastening clip against the wall so that it rests against the ceiling. The arrow on the flanged rim indicates the middle of the cooker hood. Mark the attachment holes to be drilled. Drill the holes (ø 8 mm).

Put the plugs into the wall and fix the fixing bracket to the wall with the screws supplied (5 x 50 mm).

marking out and fitting motor module

Mark the position of the underside of the hood on the wall (bear in mind the minimum distance to the hob). Mark the (vertical) centre line.

Fold or cut the template depending on type and mark the upper fixing holes.

Drill the fixing holes (2 x ø 10 mm).

Fix the plugs. Screw two nuts onto the threaded ends in the opposite direction. Screw the threaded ends into the wall leaving 20 mm projecting (see illustration).

Remove the nuts.

assembly (continued)

Technical diagram of a mechanical device with labeled components and directional arrows

Suspend the motor module on the threaded ends (1). Screw the nuts on. Make sure that the motor module is exactly level.

Drill holes (2 x ø 6 mm) and secure the motor module with the fixing pins supplied (6 x 60) (2).

Fit the discharge duct.

Connect the motor module electrically.

Technical diagram showing a mechanical assembly with directional arrows and a magnified view of the component.

fitting the hood

Fit the hood to the motor module. First hook the rear of the hood into the motor module at the bottom (1).

Then lift the front up (2) so that the two bolts supplied (M5 x 12) can be screwed in (3). Use these bolts to level the hood.

Use these screws to level the hood.

Make the plug connections in the hood.

Technical diagram showing mechanical assembly with labeled components and motion indicators

GB 12GB 12

assembly (continued)

Simple line drawing of a box with an upward arrow and two vertical lines above it (no text or symbols)

fitting the telescopic pipe

NB: During recirculation, the ventilation slits must not be covered by the lower telescopic pipe.

Slide the flanged end of the upper telescopic pipe upwards between the fixing bracket and the wall, and slide the telescopic pipe against the ceiling. The telescopic pipe locks into position.

Hook the lower telescopic pipe onto the upper part and allow the lower part to drop so that it slides into the edge of the hood.

Put the filters in place and test the extractor hood.

technical data

type number: see data plate in the hood

power supply: 230 V - 50 Hz

connected load: see data plate

dimensions (h x w x d): see "fitting dimensions"

approvals mark: Kema

This appliance complies with the CE directives.

external motors

NB: For appliances with an external motor, ATAG

recommends the use of the following types of external

motors:

WA111C5U WA300C5U

disposal of packaging and appliances

The packaging of the appliance is recyclable. It can be made up of:

-cardboard
- polyethylene
– CFC free polystyrene (PS rigid foam)
– polypropylene straps around the box

Please dispose of these materials in a responsible way in

accordance with the regulations of your local authority.

Your local authority will also be able to give you information about disposing disused household appliances in a responsible way.

préface

installation (suite)

Diagram illustrating a waste sorting or sorting process with labeled components and a recycling symbol

évacuation

Technical diagram of a mechanical component with labeled parts and dimension indicators

Technical diagram showing a mechanical assembly with a magnified detail view of the component being inserted into a bracket.

Technical diagram showing mechanical assembly steps with numbered components and directional arrows

FR 12FR 12

montage (suite)

Simple line drawing of a 3D box with a small object inside, no text or symbols present

Installation (Forts.)

Diagram illustrating a waste sorting or sorting process with labeled components and a recycling symbol

Technical diagram of a mechanical device with labeled components and directional arrows

Technical diagram showing a mechanical assembly with a magnified inset view of a bracket (no text or symbols present)

Haube aufhängen

Technical diagram showing mechanical assembly with labeled components and motion indicators

Simple line drawing of a box with a small object inside, no text or symbols present

Technische Daten