DD24SCTX9 N - Dishwasher Fisher & Paykel - Free user manual and instructions

USER MANUAL DD24SCTX9 N Fisher & Paykel

USER GUIDE3 CONTENTS Safety and warnings 5 First use 8 Loading suggestions 10 Wash programs 11 Operating instructions 12 Wash modifiers 13 Delay start 15 Keylock & Childlock 16 Detergent 17 Rinse aid 20 Water softener (some models only) 22 Preferences 24 Wi-Fi connection & remote mode 26 Racking features 28 Maintenance 33 Troubleshooting 37 Fault codes 41 Warranty and service 43 Registration To register your product visit our website: fisherpaykel.com/register USER GUIDE5

READ AND SAVE THIS GUIDE

When using your DishDrawer™ Dishwasher, follow basic precautions, including the following: General

The information in this guide must be followed to minimise the risk of fire or explosion or to prevent property damage, personal injury or loss of life.

Use the DishDrawer™ Dishwasher only for its intended function as described in this user guide.

This appliance is intended to be used in household and similar applications such as:

staff kitchen areas in shops, offices and other working environments

by clients in hotels, motels and other residential environments

bed and breakfast environments.

NSF 184-Certified residential dishwashers are not intended for licensed food establishments.

Use only detergents or rinse aid recommended for use in a domestic dishwasher and keep them out of reach of children. Check that the detergent dispenser is empty after the completion of each wash program.

When loading items to be washed, locate sharp items so that they are not likely to damage the internal lid of the DishDrawer™ Dishwasher and load sharp knives with the handle up to reduce the risk of cut injuries.

Do not touch the filter plate in the DishDrawer™ Dishwasher base during or immediately after use, as it may be hot.

Do not operate your DishDrawer™ Dishwasher unless all enclosure panels are properly in place.

Do not tamper with the controls.

Do not abuse, sit on, stand in or on the drawer or dish rack of the DishDrawer™ Dishwasher.

The drawer should not be left in the open position since this could present a tripping hazard.

The foldaway cup racks are designed to support cups, glasses and kitchen utensils. When the foldaway cup racks are in the drawer do not lean on or use them to support your body weight.

To reduce the risk of injury, do not allow children to play in or on the DishDrawer™ Dishwasher.

Under certain conditions, hydrogen gas may be produced in a hot water heater system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the DishDrawer™ Dishwasher, turn on all hot water taps and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

Some dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with the skin and eyes and keep children away from the DishDrawer™ Dishwasher when the door is open.

Under no circumstances should you open the drawer whilst the DishDrawer™ Dishwasher is in operation.

Always press to pause and wait until you hear four beeps before opening the drawer.

The DishDrawer™ Dishwasher must be used with the motor assembly, filter plate, drain filter and spray arm in place. To identify what these parts are refer to 'Maintenance'.

Take care not to load dishware items so they prevent the internal lid from properly sealing with the drawer. Items should be placed so they do not protrude above the drawer.

Cleaning and maintenance shall not be done by children without supervision.

Do not allow children to play inside, on or with this appliance or any discarded appliance.

If the DishDrawer™ Dishwasher is not being used for long periods of time, turn the electricity and water supply off.

Household appliances are not intended to be used by children. Children of less than 8 years old must be kept away from the appliance unless continuously supervised. This appliance can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they have been given supervision or instruction concerning the use of the appliance in a safe way and they understand the hazards involved.

If a dishwasher cleaner is used, we recommend running a wash program with detergent immediately afterward to prevent any damage.

The DishDrawer™ Dishwasher is designed for washing normal household utensils. Items that are contaminated by petrol, paint, steel, iron debris, corrosive, acidic or alkaline chemicals are not to be washed in the DishDrawer™ Dishwasher.

Do not wash plastic items unless they are marked dishwasher safe or equivalent. For plastic items not marked, check the manufacturer’s recommendations. Installation

This DishDrawer™ Dishwasher must be installed and located in accordance with the Installation instructions before it is used. If you did not receive Installation instructions with your DishDrawer™ Dishwasher, you can order them by calling your Authorised Repairer or download them from our local Fisher & Paykel website, listed on the back cover.

Installation and service must be performed by a Fisher & Paykel trained and supported service technician.

If the power supply cord is damaged, it must be replaced by a Fisher & Paykel trained and supported service technician or a qualified trades person in order to avoid a hazard.

Ensure the DishDrawer™ Dishwasher is secured to adjacent cabinetry using the brackets provided. Failure to do so may result in an unstable product, which may cause damage or injury.

Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or has missing or broken parts, including a damaged power supply cord or plug.

Do not store or use petrol, or other flammable vapours and liquids in the vicinity of the DishDrawer™ Dishwasher.

Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.

Ensure the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress.

Do not install or store the DishDrawer™ Dishwasher where it will be exposed to temperatures below freezing or exposed to weather.

Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket outlet box) to connect the DishDrawer™ Dishwasher to the power supply.7

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or Fisher & Paykel trained and supported service technician if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance; if it will not fit the outlet, contact a Fisher & Paykel trained and supported service technician or qualified electrician.

If the DishDrawer™ Dishwasher is installed as a permanently connected appliance, this appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Maintenance

Disconnect the appliance from the power supply before any cleaning or maintenance.

When disconnecting the appliance pull the plug rather than the power supply cord or junction of cord to avoid damage.

Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in this guide. We recommend contacting a Fisher & Paykel trained and supported service technician or Customer Care.

Keep the floor around your appliance clean and dry to reduce the possibility of slipping.

Keep the area around/underneath your appliance free from the accumulation of combustible materials, such as lint, paper, rags and chemicals. Wi-Fi

Do not change or modify the wireless communication device in any way. Changes or modifications not expressly approved by Fisher & Paykel could void the user’s authority to operate the equipment.

This device contains licence-exempt transmitter /receiver that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.

This device must accept any interference, including interference that may cause undesired operation of the device.

WARNING: The incorporated Wi-Fi module in this appliance is to operate only from

channel 1 to channel 11 as per FCC rules.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

this device must accept any interference received, including interference that may cause undesired operation.

Ensure the installer has completed the ‘Final checklist’ in the Installation instructions.

Read this guide, taking special note of the 'Safety and warnings' section.

Remove all internal and external packaging and dispose of it responsibly. Recycle items that you can. *double models only | **water softener models only Control panel features 1 On/Off + Drawer selector* 2 Wash program selector 3 Wash modifier selector 4 Start + Delay start 5 Delayed start indicator 6 Salt indicator** 7 Wi-Fi indicator 8 Lock indicator 9 Wash program indicators !0 Wash modifier indicators !1 Wash stage indicators !2 Display !3 Drawer indicator*

Double model illustrated

8 Lock indicator 9 Wash program indicators !0 Wash modifier indicators !1 Wash stage indicators !2 Display !3 Drawer indicator* FIRST USE Cutlery & silverware All cutlery and silverware should be rinsed immediately after use to prevent tarnishing, RINSE cycle is recommended. Silver should not come into contact with stainless steel, mixing these can cause staining. Remove silver cutlery from the DishDrawer™ Dishwasher and hand dry immediately. Aluminium Aluminium can be dulled by detergent. The degree of change depends on the quality of the detergent or aluminium. Other metals Iron and cast iron can rust and stain other items. Copper, pewter and brass tend to stain. Woodware Woodware is generally sensitive to heat and water. Regular use in the DishDrawer™ Dishwasher may cause deterioration over time. Glassware Most glassware is dishwasher safe. Crystal, very fine and antique glassware may etch and will develop a cloudy appearance. Plastics Some plastics may change shape or colour with hot water. Refer to the manufacturer’s guide. Dishwasher safe plastic should be weighed down so it does not flip and fill with water or fall through the base rack during the wash. Decorated items Most modern china patterns are dishwasher safe. Antique items, those with a pattern painted over the glaze, gold rims or hand painted china may be more sensitive to machine washing. Glued items Certain adhesives are softened or dissolved in machine washing. If your home has hard water

Refer to 'Powdered detergent quantity recommendations'.

Use rinse aid. We recommend you raise the rinse aid setting to 5 to help improve wash performance. Refer to 'Preferences' for details. Use a dishwasher cleaner/descaler regularly, or whenever you notice a build-up of limescale deposits in your DishDrawer™ Dishwasher. If your home has soft or softened water

Avoid using too much detergent. Dishware The combination of high temperatures and dishwasher detergent may cause damage to some items. Refer to the manufacturer's guidance or wash by hand if in doubt. Water hardness Hard water is water with a high concentration of minerals such as calcium and magnesium. It can be detrimental to the performance of your DishDrawer™ Dishwasher and parts can fail over time. Glassware washed in hard water will become cloudy and dishes will become spotted or covered in a white film over time. Water hardness varies by geographical location. If you live in a hard water area, and your DishDrawer™ Dishwasher does not have a built-in water softener, we recommend fitting a water softener to the household water supply.10 LOADING SUGGESTIONS Ensure

Spray arms can rotate freely.

Glass and other fragile items are stable.

All dish openings are facing downwards.

Plates are evenly spaced.

All sharp objects are located securely to avoid injury or damage to the product. Avoid

Any protrusions below the racks and basket that may prevent spray arm rotation.

Any protrusions at the top of the drawer.*

Blocking water from any items on the foldaway cup racks. Remove all food scraps before carefully loading into the drawer. When loading your drawer ensure items are placed so water coming from the rotating spray arm below can reach all areas. Wash performance will be reduced if it can't. *maximum dishware height for standard tub models is 280mm and 310mm for tall tub models.11 Your DishDrawer™ Dishwasher has a number of wash programs designed to suit your needs. Selecting the most appropriate cycle for each load will help ensure the best wash results. The Eco program is the most efficient program in terms of combined energy and water consumption. Loading the dishwasher to capacity will contribute to water and energy savings. Pre-rinsing of tableware items will increase water and energy consumption and is not recommended. Washing tableware with a household dishwasher usually consumes less energy and water than hand washing, when used according to manufacturer's instructions. WASH PROGRAMS

WASH PROGRAM DESCRIPTION

HEAVY Designed for heavily soiled pots, pans and dishes MEDIUM Best for dishes that are quite heavily soiled or to remove food soils that have been left to dry overnight ECO For normally soiled dishes for optimum water and energy use FAST Lightly soiled dishes DELICATE For lightly soiled and heat sensitive crockery and glassware such as wine glasses RINSE Prevents odours and soils from drying on dishes Ensure DishDrawer™ Dishwasher is turned on and detergent has been added. Press to scroll through the available wash programs. The selected wash program will illuminate on the display. Press to start the wash.

Setting a wash program12 OPERATING INSTRUCTIONS Pausing a wash Resuming a wash Cancelling a wash To pause the current wash program, press

WASH and * will flash in the display Wait for three short and one long tone before opening the drawer. Forcing it open mid cycle may cause damage or injury. If the drawer is not restarted within 7 minutes it will tone intermittently until it is restarted. Press

If there is any water in the drawer, it will drain before the DishDrawer™ Dishwasher turns off. To resume, press again. *double models only13 WASH MODIFIERS After setting the wash program, you may select one of the following the additional options. Only one modifier can be set at a time. EXTRA DRY Increases the final rinse temperature and the length of the drying phase. QUICK Uses additional water and energy for a faster wash time. SANITIZE Raises the water temperature during the rinse phase to sanitize.

WASH PROGRAM MODIFIER AVAILABLE

HEAVY Extra Dry, Quick, Sanitize MEDIUM Extra Dry, Quick, Sanitize ECO n/a FAST Extra Dry DELICATE Extra Dry, Quick RINSE n/a Setting a wash modifier Ensure DishDrawer™ Dishwasher is turned on, detergent has been added and a wash program has been selected.

Press to scroll through the available wash modifiers. The selected wash modifier indicator will illuminate on the display. Press to start the wash.

WASH MODIFIERS Using SANITIZE The SANITIZE wash modifier adjusts the wash program to meet the conditions required by

Section 6, NSF 184 for sanitization to occur. While SANITIZE is running, the wash program is

monitored to ensure that these conditions are met. Only programs utilising the SANITIZE wash modifier are certified to meet the conditions required by Section 6, NSF 184. Other wash programs may not reach the temperatures required for sanitization to occur. See table on previous page for wash programs that have sanitize available. For sanitization to occur, the temperature of the water needs to reach 70°C. Ensure all items are dishwasher safe before running the sanitize modifier. If the wash is interrupted or the water supply is turned off during the program, the heating conditions for sanitization may not be met. You may need to run the program again. If sanitization has been successful The DishDrawer™ Dishwasher will beep,

will show in the display and the SANITIZE indicator will remain lit. After 30 seconds the display will turn off. If sanitization has not been successful An alert will sound and an alert code will show in the display. The SANITIZE indicator will not be lit. 1 Check if the water supply has been turned off or the wash program interrupted. 2 Press once to stop the beeping and then again to clear the alert code. 3 Run the SANITIZE cycle again. For more information, refer to 'Fault codes'.15 Single models Press

Double models Press and hold

Press and hold until 1h appears in the display to enter DELAY START mode. DELAY START can delay the start of the wash program between 1–12 hours. The display will show the number of hours until the wash program is set to begin. Cancelling Delay start

DELAY START *double models only Press to increase the delay start time. and * will flash in the display and the countdown will begin. The wash will start once the delay time is over, provided the door is closed. If the drawer is opened after DELAY START has been set, DELAY START will be paused after closing the drawer. Press to resume. If you scroll past 12 hours the dishwasher will exit DELAY START mode Setting Delay start16 KEYLOCK & CHILDLOCK Keylock Childlock To activate KEYLOCK Press and hold and together until you hear a tone and illuminates in the display. To cancel KEYLOCK Press and hold and together until you hear a tone sound and dims in the display. KEYLOCK disables all buttons across the control panel and door, and locks all drawers closed. CHILDLOCK disables all buttons across the control panel and door and locks all drawers closed. To activate CHILDLOCK Press and hold and together until you hear two tones and illuminates in the display. To cancel CHILDLOCK Press and hold and together until you hear two tones sound and dims in the display.17 DETERGENT Press the latch down to open the dispenser. Check that the dispenser is empty and dry.

Add detergent and close the dispenser until it clicks shut. The detergent will automatically be released into the drawer during the wash program. main dispenser secondary dispenser When washing heavily soiled dishware in hard water, more detergent may be required. Refer to 'Powdered detergent quantity recommendations'.

WARNING: Dishwasher detergents are strongly alkaline. They can be extremely dangerous

if swallowed. Avoid contact with the skin and eyes and keep children and infirm persons away from the dishwasher when it is open. Check the powdered detergent dispenser is empty after each wash. Unsuitable detergents These types of detergent are not suitable and may damage your DishDrawer™ Dishwasher and lead to a service call that is not covered by warranty:

Hand washing liquids

Disinfectants Using powdered detergent Use the markings to help you measure the correct quantities. Do not place tablets or pouches in the dispenser. Refer to the following 'Powdered detergent quantity recommendations' table and the detergent manufacturer’s guidance. No detergent is needed for RINSE.18 DETERGENT Using solid tablets or pouches Using tablets could improve wash performance in hard water areas. Follow manufacturer guidance. Some tablets or pouches may not be suitable for all wash programs. Place directly in tub Place the tablet or pouch between the racking at the side as shown. Do not place on the base of the drawer as it may interfere with the spray arm rotation and affect wash performance. Place on tablet tray Place tablet or pouch on tablet tray in cutlery basket ensuring it doesn't come in direct contact with dishes or cutlery. Place in cutlery basket Place tablet or pouch in cutlery basket, ensuring it doesn't come in direct contact with dishes or cutlery.19 DETERGENT Powdered detergent quantity recommendations

If you have hard water in your area, more detergent may be required. Refer to 'Water hardness' for more details

WASH PROGRAM DETERGENT QUANTITY PER DRAWER

HEAVY 2/3 MEDIUM 2/3 ECO 2/3 FAST 1/3 DELICATE 1/3 RINSE n/a20 RINSE AID Rinse aid provides a streak-free finish to glass and dishware as well as preventing metal from tarnishing. We recommend using a liquid rinse aid regularly for optimal drying results. During dispensing, a pulsing sound may be heard, this is normal. The rinse aid dispenser is located on the inside of the drawer underneath the detergent dispenser. It holds approximately

1.7 fl oz (50ml) of rinse aid.

How much rinse aid to use The amount of rinse aid dispensed in each wash may need adjusted to suit your water conditions. Refer to 'Preferences' and 'Water softener' for guidance. When to refill rinse aid

If the indicator glows or flashes dimly or not at all, you do not need to refill – there is enough rinse aid for the wash. When using lighter coloured rinse aids, the indicator may not dim as prominently as when using darker rinse aids. rinse aid dispenser rinse aid indicator21 RINSE AID How to refill rinse aid Turn the plug anticlockwise and remove.

Pour rinse aid into the opening taking care not to spill any into the drawer. Any accidental spillages must be wiped up. If not wiped up, spilt rinse aid will cause excessive foaming which may result in a service call that will not be covered by warranty Refit the plug, turning clockwise until secure. Ensure the plug is closed tight with the hand grip in a vertical position.22 WATER SOFTENER (SOME MODELS ONLY) The salt reservoir is located on the inside of the drawer next to the detergent dispenser. It holds up to approximately 0.8lb (350g) of salt (actual capacity will vary depending on brand and grain size of salt used). Double models: each drawer has a separate salt reservoir. The salt reservoir must always be filled with granular salt designed for dishwasher water softening. We do not recommend the use of cooking salt like table salt, rock salt or pellets as they may contain impurities that will damage the water softener. Do not add detergent or rinse aid to the salt reservoir. This will cause damage. salt indicator light salt reservoir cap SETTING

Use the table below to determine the optimal water hardness setting. Your local water company will be able to help.

If you have a household water softener installed, use the setting recommended for water with a hardness under 100 ppm/6 gpg, irrespective of the water hardness in your area.

If your water hardness is above 625 ppm/36 gpg, the wash performance of your DishDrawer™ Dishwasher will decline over time. The rinse aid setting should be at 5.23 When to refill the salt reservoir

If the salt indicator is red, the salt reservoir must be filled. If the salt indicator is black, there is enough salt in the reservoir.

will also illuminate on the display if the salt reservior must be filled. WATER SOFTENER (SOME MODELS ONLY) Using the salt reservoir You may hear some noises when the water softener is operating, this is normal. Turn the cap anticlockwise and remove.

Refit the cap, turning clockwise until secure. If you are not washing your dishes immediately after filling the salt reservior, we recommend running a RINSE cycle to remove any salt water or spilt granules. Place the salt into the salt container and carefully pour into the reservior. When filling the salt reservior, you may notice water being displaced from the water softener overflow. This is normal.24 PREFERENCES

OPTION DISPLAY SETTINGS

Wi-Fi Con Disconnected n/a Connected Rinse aid

bPo Off bP- You can adjust any of the settings of the below options prior to starting a wash cycle. Wi-Fi Allows your DishDrawer™ Dishwasher to connect to your home network. Refer to 'Wi-Fi connection & remote mode' for details. Rinse aid Controls the amount of rinse aid dispensed. Refer to 'Rinse aid' for details. Water softener* Refer to 'Water softener' for details. Auto power-on** Your DishDrawer™ Dishwasher is set to automatically power on for 30 seconds after a drawer is opened. This can be turned off. Autolock Allows the drawer to automatically lock 30 seconds after it’s closed. Tones Adjusts tone settings. When set to OFF all tones will be silenced except fault alerts. *Some models only | **Suitable as a Sabbath option.25 PREFERENCES Changing the settings Ensure there is no wash in progress, then press

Press and hold and together for four seconds.

Press to scroll through the available options. Press to change the setting within an option. Press to save the new setting and leave the preference menu. Double models Changing the settings in one tub will set your preferences for both drawers.

Your appliance can be connected to your home wireless network and operated remotely using the app. Getting started

Ensure your home Wi-Fi network is turned on.

You will be given step by step guidance on both your appliance and mobile device.

It may take up to 10 minutes to connect your appliance.

For further guidance and troubleshooting, please refer to the app. On your mobile device: 1 Download the app from www.fisherpaykel.com/connect 2 Register and create an account. 3 Add your appliance and set up the Wi-Fi connection. Connecting to your home Wi-Fi Ensure there is no wash in progress. Press and hold and together for four seconds.

Press and hold to save and leave the menu after Wi-Fi is connected. Press and hold to connect to the Wi-Fi network. When flashes, follow the prompts within the app to complete set-up.27

WI-FI CONNECTION & REMOTE MODE

Enabling remote mode Disabling remote mode REMOTE MODE will automatically be disabled after 72 hours or if a fault occurs. Opening the drawer will also disable REMOTE MODE. Double models only: Select a drawer to operate remotely. With your DishDrawer™ Dishwasher connected to your Wi-Fi network, press and hold for four seconds. A tone will sound and will flash. REMOTE MODE is now enabled. If the drawer is open: While is flashing, close the drawer to enable REMOTE MODE. If the drawer is not closed within 4 seconds while is flashing, REMOTE MODE will not be enabled.

RACKING FEATURES Removable anti-nesting grid Use the anti-nesting grid to separate cutlery items and stop them from nesting together. The grid clips onto the top of the cutlery basket. Cutlery basket To reduce the risk of injury, we recommend loading knives and sharp utensils with handles facing up. Mix spoons, knives and forks within each section to stop cutlery nesting together and to ensure the water circulates freely. Keep stainless steel from touching silver cutlery to avoid staining. Cutlery basket accessories Cutlery basket features and accessories 1 Cutlery basket 2 Removable anti-nesting grid 3 Removable tablet tray 4 Removable small items container

RACKING FEATURES Removable tablet tray If you are using dishwasher tablets or gel packs, place them on the removable tablet tray. Ensure the tablets are not in direct contact with dishes or cutlery. See 'Detergent' for more information. Removable small items container Small, light items like baby bottle teats are best placed into the small items container to prevent them from being displaced during the wash. The container can clip to the side of the cutlery basket, into the cutlery basket or can be placed elsewhere in the drawer. If you place the container elsewhere in the drawer, ensure water from the spray arm can still access items in and around the container. If laid flat, ensure the solid plastic side is facing up.30 RACKING FEATURES To adjust height 1 Fold up to unlock the rack. 2 Adjust the height to suit by sliding up or down. 3 Fold back down to lock in the position. Foldable cup racks Each cup rack can be folded away independently to create more space within the drawer and are height adjustable. Racking features 1 Folding tine rack 2 Adjustable tine rack 3 Base rack 4 Trap door Not illustrated: foldable cup racks, knife clip, glass supports

4 Trap door Not illustrated: foldable cup racks, knife clip, glass supports RACKING FEATURES Knife clip Glass supports These removable clips provide extra stability when needed. This clips onto the adjustable racks and supports knives and other utensils during the wash. Always ensure that knife blades are facing down. To remove 1 Fold tines down towards each other. 2 Unclip the rack at each end by pulling firmly towards you. To replace 1 Line up the clips with the base rack. 2 Push firmly to click rack into place. Folding tine rack The folding tines can be removed if desired, however it is recommended the tines are folded down rather than removed if more space required.32 RACKING FEATURES Adjustable tine rack This rack is designed to fit deep bowls or small plates by adjusting the spacing of the tines. To adjust spacing To remove To replace Slide the tines backward or forward by pushing or pulling the front handle. Grip the front and back handles and pull up to unclip. Align front and rear clips with the base rack and clip into place.33 MAINTENANCE Tub features 1 Drain filter 2 Filter plate 3 Spray arm Disconnect the DishDrawer™ Dishwasher from the power supply and allow it to cool before undertaking any cleaning or maintenance.

Cleaning surfaces Wipe with a damp cloth and dry using a lint-free cloth. Take care not to wet the LCD display. We do not recommend using the following cleaning aids as they may damage the surfaces:

Plastic or stainless steel scouring pads

Abrasive, solvent, household cleaners

Acid or alkaline cleaners Cleaning the drain filter, spray arm and filter plate We recommend that the drain filter and filter plate in each drawer are removed and cleaned once a month or whenever there is evidence of food particles. The spray arm in normal use should require cleaning less frequently. These parts can be shaken to remove any foreign material, cleaned in hot water, then rinsed in clean water. The DishDrawer™ Dishwasher must be used with the filter plate, drain filter and spray arm correctly in place. We recommend that you always use the DishDrawer™ Dishwasher with the right hand folding tine rack in place. If a dishwasher cleaner/descaler is used, you must run a wash program with detergent immediately afterward to prevent any damage to your DishDrawer. Extended periods of disuse If the DishDrawer™ Dishwasher is not going to be used for some time we recommend turning off the power and water supply, leaving it clean and empty with the drawers ajar. When using your DishDrawer™ Dishwasher for the first time after a long period away, we recommend pouring 3 cups of water into the drawer before use. This helps lubricate components that may have dried out during dis-use.

Hand washing liquids or soap

Stainless steel cleaners or polishes

Laundry detergents or disinfectants34 Twist the drain filter counter-clockwise and lift to remove. Separate the holder and the mesh by pinching one side of the mesh and pulling. Do not attempt to remove the mesh by pinching both sides as this may cause damage. Clean under hot soapy water and rinse thoroughly. Click the drain filter mesh back onto the holder and twist until the arrows on the mesh and holder align.

For ease of access to the drain filter and filter plate, the base rack can be removed by lifting it from the rear. Alternately, remove the cutlery tray, lift the trap door and remove the fixed tine rack. Refer to 'Racking features' for details. Removing and cleaning the drain filter Replacing the drain filter Push the drain filter back into the tub and rotate clockwise until the arrows on the filter and base of the drawer align.

holder mesh MAINTENANCE35 MAINTENANCE With the drain filter removed, carefully lift the drain filter plate up and out. Clean under hot soapy water and rinse thoroughly. Lift the spray arm off the impeller. Shake to dislodge any loose particles, rinse under running water and wipe with a damp cloth. Push the drain filter plate back onto the tub ensuring there are no particles in the recess. Place the spray arm to the impeller. Ensure the arm rotates freely when refitted. Removing and cleaning the drain filter plate Removing and cleaning the spray arm Refitting the drain filter plate Refitting the spray arm impeller36 MAINTENANCE Winterizing (cold climates) If the DishDrawer™ Dishwasher is installed in a cold climate where temperatures fall below zero, we recommend winterizing. Turn off the water supply. Disconnect the drain hoses from the sink drain pipe and the water inlet pipe from the water valve. Drain the water from the hoses, inlet pipe and water valve, using a bucket or pan to collect the water. Reconnect the water inlet pipe to the water valve and hoses to the sink drain pipe.

Remove the drain filter and the filter plate from the bottom of the drawer. Use a sponge to remove any remaining water from underneath before replacing.37 TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Unclean dishes Unsuitable wash program for load selected. Select the appropriate wash program for the load. Refer to 'Wash programs'. Spray arm unable to rotate. Ensure no items are obstructing the spray arm path. Make sure the spray arm is mounted correctly and free to rotate. Drawer incorrectly loaded. Refer to 'Loading suggestions'. Filter plate or filter is incorrectly inserted. Refer to 'Maintenance'. Filter plate or filter is blocked. Clean the filter plate and drain filter. Refer to 'Maintenance'. Detergent put in the wrong compartment of the dispenser. Detergent must be placed in the large compartment. Refer to 'Detergent'. Incorrect detergent use. Refer to 'Detergent' and follow the detergent manufacturer’s instructions. Excess food on dishware. Scrape all food scraps prior to loading. Spray arm holes are blocked. Clean the spray arm. Spray arm rotation blocked. Remove any protrusions below the rack and ensure the spray arm can rotate freely. Hard water. Increase the rinse aid setting and the amount of detergent used. Refer to 'Water hardness'. Hard water Increase the rinse aid setting and the amount of detergent. Refer to 'Water hardness'. Water softener models: Increase the water softener setting. Refer to 'Water softener'. Non-water softener models: If living in an area with very hard water, consult a plumber on installing a household water softener.38 TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Foaming Incorrect detergent use. Refer to 'Detergent'. Egg left on plates. Rinse excess egg prior to loading. Rinse aid setting too high. Decrease the rinse aid setting. Rinse aid dispenser plug not closed properly. Ensure the plug is closed tight with the hand grip in a vertical position. Refer to 'Rinse aid'. Water leaking Drain hose disconnected from waste pipe. Reconnect the drain hose to the waste pipe. Water inlet hose not connected correctly. Ensure the inlet hose is connected securely. Other leaks. Turn water and power supplies to the DishDrawer™ Dishwasher off. Call Customer Care or your Authorised Service Centre. Rinse aid dispenser plug not closed properly. Ensure the plug is closed tight with the hand grip in a vertical position. Refer to 'Rinse aid'. Drawer will not open (no tones or wash in progress) CHILDLOCK is on. Turn CHILDLOCK off. Refer to 'Keylock & Childlock'. Closed drawer auto lock is on. Press any button and open drawer within 30 seconds. Power failure during wash program Power outage in your home or area. Wait until power resumes, program will restart in same part of wash program. Continuous beeping with A / F code in display A fault has occurred. Refer to 'Fault codes'. Intermittent beeping DishDrawer™ Dishwasher is paused. Close the drawer and press to resume the program.39 TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

DishDrawer™ Dishwasher will not start Power supply is not connected. Connect the power supply. The drawer is not closed properly. Ensure the drawer is firmly closed. KEYLOCK or CHILDLOCK feature is on. Turn KEYLOCK or CHILDLOCK off. See your Quickstart guide for instructions. Cycle not started. Press

DishDrawer™ Dishwasher is in Demo mode. Contact Customer Care. Fan noise after a wash program has finished This is normal. The fan continues to run to assist with drying. The fan will automatically stop after a set time, or when the drawer is opened. The fan may resume when the drawer is closed again. Fan noise starts when I close the drawer, even though I didn’t start a new wash This is normal. In some cases, the fan will run when the drawer is closed for a set time after a program has finished. No action required. The fan will automatically stop after the set time is over. No powdered detergent dispensed Detergent dispenser was wet when loaded. Clean the dispenser and ensure it is dry before adding detergent. Refer to 'Detergent'. The wash seems to have finished, but the drawer will not open The wash program is still in progress. It is in a quiet phase that is needed for optimal performance. No action required. The program will transition into a more audible phase after the quiet phase is over. Water pooling on inner rim of drawer after a wash This is normal condensation. Wipe dry. Water under the filter This is normal. No action required. Excess water in the drawer Drain hose(s) bent. Straighten the drain hose(s). Blocked filters. Refer to 'Maintenance'.40 TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES WHAT TO DO

Water marks on the dishes Rinse aid depleted. Refill the rinse aid dispenser. Rinse aid setting too low. Increase/turn on the rinse aid setting. DishDrawer™ Dishwasher overloaded/ incorrectly loaded. Refer to 'Loading suggestions'. Drawer interior is stained Some foods may stain the inside of the drawer. Pre-rinse dishes before placing in the drawer. Alternatively, use RINSE after adding the dishes may minimise staining.41 FAULT CODES How do I know if there is a fault? Your DishDrawer™ Dishwasher will beep continuously and a fault code will flash in the display. There are two types of fault codes – ‘F’ and ‘A’. Double models only

There may be a fault in one or both of the drawers and the fault codes may be different in each.

The drawer indicator also flash to show which drawer has a fault.

If there is a fault in both drawers, both drawer indicators will flash.

If a fault occurs in one drawer only you are still able to use the other drawer. If you have paused a drawer during a wash program, and the other drawer then faults, the paused drawer indicator will continue flashing but will be dimmed. To fix a fault First try to fix the issue and clear the code according to the steps in the following tables. If the problem persists: 1 Note down the fault code. Double models only: Press to scroll between the drawers and note down the code for each drawer. 2 Contact Customer Care for support or to organize a visit by a service technician. Refer to the Service and Warranty booklet for contact details. ‘F’ fault codes You may be able to clear the fault by resetting the DishDrawer™ Dishwasher. Follow the steps below: 1 Press to stop the beeping, then again to turn the DishDrawer™ Dishwasher off. 2 Wait a few seconds. Press again to turn the DishDrawer™ Dishwasher back on. When the fault code has disappeared, the fault has been reset and you can continue to use your DishDrawer™ Dishwasher.42 FAULT CODES ‘A’ fault codes Follow the steps below to try and fix the issue.

DISPLAY POSSIBLE CAUSE WHAT TO DO

Water supply fault. 1 Ensure the water supply is turned on. 2 Press once to stop the beeping, then again to clear the fault. 3 Press to resume the wash program.

Drawer cannot drain. The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. 1 Ensure the drainage hose and connection to pipes are not blocked. 2 Press once to stop the beeping, then again to clear the fault. 3 Press to resume the wash program.

The spray arm has loosened or come off its mounting, or water pressure is too low. 1 Open the drawer and check the spray arm. 2 If the spray arm has loosened or come off its mounting, re-fit it. Check that it is firmly seated and turns freely. Refer to 'Maintenance'. 3 Press once to stop the beeping, then again to clear the fault. 4 Press to resume the wash program.

Auto recovery program: DishDrawer™ Dishwasher has detected excess foam in the drawer. 1 Let the auto recovery program run until it is complete. The wash program will resume when the auto recovery program has completed. 2 Check that you are using the right detergent before running another wash program. 3 If the drawer is still filled with foam at the end of the wash program, contact Customer Care. A09 Sanitize cycle hasn’t met temperature needed to sanitize dishes. 1 Check if the water supply has been turned off or the wash program interrupted. 2 Press once to stop the beeping, then again to clear the fault. 3 Run the sanitize cycle again.43 Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Suburb Town Country

WARRANTY AND SERVICE

Before you call for service or assistance Check the things you can do yourself. Refer to the installation instructions and your user guide and check that: 1 Your product is correctly installed. 2 You are familiar with its normal operation. If after checking these points you still need assistance or parts, please refer to the Service & Warranty book for warranty details and your nearest Authorised Service Centre, Customer Care, or contact us through our website www.fisherpaykel.com. Wash program data & standards test information Wash program data and standards test information can be viewed online by going to https://www.fisherpaykel.com and searching your model code.592816B 09.24 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2024. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time. For current details about model and specification availability in your country, please go to our website or contact your local Fisher&Paykel dealer.GUIDE D’UTILISATION

PROBLÈME CAUSES POSSIBLES SOLUTION

Vaisselle sale Le programme de lavage sélectionné ne convient pas àlavaisselle chargée. Sélectionnez le programme de lavage approprié pour la vaisselle chargée. Reportez- vous à 'Programmes de lavage'. Le bras gicleur ne tourne pas. Assurez-vous qu’aucun article ne bloque latrajectoire du bras gicleur. Assurez-vous que le bras gicleur est correctement installé et qu’il peut tourner librement. Le tiroir est chargé demanière incorrecte. Reportez-vous à 'Suggestions pour le chargement'. La plaque de filtration ou le filtre n’est pas installé correctement. Reportez-vous à 'Entretien'. La plaque de filtration ou le filtre est bloqué. Nettoyez la plaque de filtration et le filtre devidange. Reportez-vous à 'Entretien'. Le détergent se trouve dans le mauvais compartiment dudistributeur. Placez le détergent dans le grand compartiment. Reportez-vous à 'Détergent'. Utilisation d’un détergent incorrect. Reportez-vous à 'Détergent' et suivez lesinstructions du fabricant du détergent. Restes de nourriture sur la vaisselle. Délogez tous les restes de nourriture avant de charger la vaisselle. Les ouvertures du bras gicleur sont bloquées. Nettoyez le bras gicleur. La rotation du bras gicleur est entravée. Retirez tout article dépassant sous la grille et assurez-vous que le bras gicleur peut tourner librement. Eau dure. Augmentez le réglage du produit derinçage et la quantité de détergent utilisée. Reportez- vous à 'Dureté de l’eau'.38 DÉPANNAGE

PROBLÈME CAUSES POSSIBLES SOLUTION

Eau dure Augmentez le réglage du produit de rinçage et la quantité de détergent. Reportez-vous à'Dureté de l’eau'. Modèles avec adoucisseur d’eau: Augmentez le réglage de l’adoucisseur d’eau. Reportez- vous à ‘Adoucisseur d’eau’. Modèles sans adoucisseur d’eau: Si vous habitez dans une région où l’eau est très dure, consultez un plombier au sujet de l’installation d’un adoucisseur d’eaudomestique. Formation demousse Utilisation d’un détergent incorrect. Reportez-vous à 'Détergent'. Restants d’œufs sur lesassiettes. Rincez les restants d’œufs avant de charger la vaisselle. Le réglage du produit de rinçage est trop élevé. Réduisez le réglage du produit de rinçage. Le bouchon du distributeur de produit de rinçage n’est pas fermé correctement. Assurez-vous de fermer le bouchon de manière hermétique, avec la poignée dans une position verticale. Reportez-vous à'Produit de rinçage'. Fuite d’eau Le tuyau d’évacuation est débranché du conduit d’évacuation. Raccordez le tuyau d’évacuation au conduit d’évacuation. Le tuyau d’alimentation en eau n’est pas raccordé correctement. Veillez à ce que le tuyau d’alimentation soit solidement raccordé. Autres fuites. Coupez l’alimentation en eau et en électricité du lave-vaisselle DishDrawer™. Appelez leservice à la clientèle ou un centre deservice autorisé. Le bouchon du distributeur de produit de rinçage n’est pas fermé correctement. Assurez-vous de fermer le bouchon de manière hermétique, avec la poignée dans une position verticale. Reportez-vous à'Produit de rinçage'. Le tiroir ne s’ouvre pas (aucune tonalité ou lavage en cours) CHILDLOCK (VERROU POUR ENFANTS) estactivé. Désactivez CHILDLOCK (VERROU POUR ENFANTS). Reportez-vous à 'Verrou des touches et verrou pour enfants'. Le verrouillage automatique du tiroir fermé est activé. Appuyez sur n’importe quelle touche et ouvrez le tiroir dans un délai de 30secondes.39 DÉPANNAGE

PROBLÈME CAUSES POSSIBLES SOLUTION

PROBLÈME CAUSES POSSIBLES SOLUTION