SL B22 AA0 - Vacuum Cleaner HOTPOINT ARISTON - Free user manual and instructions

USER MANUAL SL B22 AA0 HOTPOINT ARISTON

Before you begin using the appliance, it is important that you carefully read these instructions and keep them for further reference.

GENERAL SAFETY RULES

The safety features of your vacuum cleaner comply with the technical specications and regulations in force. Do not use the appliance for any use other than its intended use. Any improper use could cause damage to persons and/or property. The voltage of your system must match the voltage of the vacuum cleaner (220- 240 V). Any connection error could cause irreversible damage to the appliance and void its warranty.

• If the plug, power cord or appliance appear to be damaged or if any visible damage is found, do not operate the vacuum cleaner.

2. Bristle-adjustment pedal

7. Pipe length regulator

12. Trolley System opening/closing button

13. Dust compartment opening button

20. Buttons +/- for electronic power adjustment

22. Battery compartment

24. Remote Power Control signal receiver

28. Attachment compartment

Version with dust bag:

33. Dust bag support

38. Dust compartment

Version without dust bag:

38. Dust compartment

INTRODUCTION Thank you for purchasing our Trolley Power vacuum cleaner. In doing so you have opted for an effective, high performance appliance. We advise you to register this product on www.hotpoint. co.uk to make sure you are entitled to all the benets made available by Hotpoint Customer Service. The Trolley Power was designed to ensure optimum performance and consistent usability. The exclusive Trolley System ensures maximum manouverability and helps you move freely around the house without knocking against the furniture. The Remote Power Control (if available) enables you to adjust the suction power directly and effortlessly from the hand grip, with no need to bend. This appliance was developed for household use only and should not be put to industrial use.hotpoint.eu

• Never suck up any sharp or cutting objects as this could damage the appliance.

• If very ne dust or powders are sucked up such as our, etc. small electrostatic discharges could occur. When sucking up materials previously mentioned, we advise not to use the metal extension pipe, but only the plastic exible hose and to set a low suction power level.

• For your safety, every repair or maintenance action should be carried out on the appliance only by Hotpoint authorised staff.

• No responsibility shall be accepted in case of damage resulting from any improper use of the appliance.

Remove all adhesives, protective plastic materials and cardboard packaging. Make sure all adhesive parts are removed with a soft damp cloth. Assembling

1. Fasten the plastic exible hose (10) to the

suction inlet (15) until it clicks into place. To remove it, press the release (16) and pull it out.

2. Fit the metal extension pipe (8) into the hand

grip (9) until it locks into place. Use the length regulator (7) to adjust the length of the pipe.

3. Fit the standard/carpet brush (1) or

the attachment you need (see chapter “Attachments”) into the end of the metal extension pipe until it locks into place. If your appliance is equipped with a Remote Power Control, you will need to insert the batteries supplied (see paragraph “Remote Power Control” under chapter “Features”). USING THE VACUUM CLEANER (A) Do not use the vacuum cleaner without lters, Pure Clean dust bag, dust bag support or dust container, as the appliance could get damaged.

1. Unwind the power cord (32) and plug the

appliance into an electrical outlet (220/240V). In such cases have it checked exclusively by Hotpoint authorised staff in order to avoid any hazardous situation.

• Regularly check the condition of the power cord.

• This appliance was not designed to be used by persons (including children) with reduced physical, sensory or mental capabilities . Nor, in addition, persons lacking experience or familiarity with the product, unless they are supervised or instructed on the use of the appliance by a person responsible for their safety.

• Supervise children to prevent them from playing with the appliance.

• Never leave the appliance unattended when it is plugged into an electrical outlet.

• Never use the power cord to move or carry the appliance around.

• After use, disconnect the plug from the electrical outlet and rewind the power cord.

• Do not bend the power cord and keep it away from sharp edges to avoid any damage.

• Never leave or use the appliance over or close to ames, ovens, ammable materials or other sources of heat.

• Do not use the vacuum cleaner on persons or animals. Keep the suction ends away from your body while it is in operation.

• Before changing an attachment, when cleaning or maintaining the appliance, and in any case after every use, unplug it from the electrical outlet.

• Should you suspect a failure, immediately unplug it from the electrical outlet.

• Never immerse the vacuum cleaner in water or any other liquid. Never spray any liquid substances onto the appliance.

• Do not leave the appliance in the open air and exposed to inclement weather conditions.

• For safety, we advise you to keep the vacuum cleaner always lower than your own position when cleaning the stairs. Never suck up any liquid or damp substances as this could affect the operation of the appliance.

• Never suck up any ammable materials or incandescent objects such as ash, cigarette ends etc. Some parts of the vacuum cleaner could catch re.hotpoint.eu

Trolley System (12) to pull out the carry handle (11) until it locks into place at the desired length.

2. Having completed your cleaning, press

the opening/closing button on the Trolley System and close the carrying handle until it locks into place. Use the Trolley System's carrying handle to store the appliance, making sure you have correctly locked it into place. Remote Power Control (C) The Remote Power Control (if available) enables you to adjust the suction power directly and effortlessly from the hand grip (9), with no need to bend. When using the vacuum cleaner, you can keep it on standby by pressing the standby button (21). To insert or change the batteries of your Remote Power Control:

1. Open the battery compartment (22).

2. Insert two AAA batteries, making sure of the

positive and negative poles.

3. Close the battery compartment until it clicks

into place. Start & Stop (D) The Start & Stop function (if available) lets you keep the vacuum cleaner on stand-by and lock the cleaning head in the park position: just insert the brush into its horizontal housing (29). Dual System (E) The Trolley Dual Clean version of the Trolley Power makes your use of the appliance extremely versatile because it can be used with or without dust bag. Just assemble the conversion kit in the package: it comprises a Pure Clean dust bag (34), dust bag support (33), gasket (37), and motor lter grill (36) already tted to the motor lter (35). The assembling takes place as follows:

1. Make sure the appliance is disconnected

from the electrical outlet.

2. Press the dust-compartment opening button

(13) to open the dust compartment lid (14) and remove the dust container (39).

3. Fit the gasket into the special groove along

the perimeter of the dust compartment (38).

4. Fit the motor lter grill (already tted to

We advise you to unwind the entire power cord (app. 7m) to avoid any overheating and damage.

2. Press the start/stop button (18) to start the

3. Press the Trolley System opening/closing

button (12) to extend the carrying handle (11) to the desired length until it locks into place. Then manoeuvre the vacuum cleaner using the carrying handle when cleaning the house.

4. To select the desired suction intensity

(based on the model) use the +/- button and electronically adjust the power (20) of the Remote Power Control; or manually rotate the electronic power regulator (25). We advise you to use a low suction power on delicate surfaces such as curtains, fabrics, cushions etc to avoid any damage; or at least open the air regulator to reduce the suction effect.

5. To pause the vacuum cleaner, if this feature

is available, you can use the standby button (21) on the Remote Power Control or the Start & Stop function (based on the model). Just insert the brush into its horizontal housing (29).

7. Disconnect the plug from the electrical

outlet and press the cord-rewind button (19) until rewinding is complete. Make sure the cord does not get entangled during rewinding.

8. Secure the oor head into its horizontal /

vertical housing and store the appliance. Do not start the vacuum cleaner if the plastic exible hose is entangled, as this could damage the appliance. FEATURES Trolley System (B) The Trolley System allows you to move your vacuum cleaner easily when cleaning and carry it from room to room effortlessly.

1. Press the opening/closing button on thehotpoint.eu

container correctly and close the dust compartment lid until it clicks into place. The appliance is equipped with a safety device that prevents the dust compartment lid from closing unless the dust bag / container has been correctly installed. Replacing the Pure Clean dust bag (G) We recommend always using Hotpoint original Pure Clean dust bags, because their special fabric allows optimum air ltration, maximum dust/powder retention, high performances and a long motor life. As the Pure Clean dust bags (34) are made of fabric, they are more resistant than conventional paper bags and can retain very ne dust/powder particles more effectively, thus ensuring maximum hygiene. We recommend replacing the Pure Clean bag as soon as the full-bag indicator illuminates. Change at least once a year to be always sure of the hygienic condition of your vacuum cleaner. The pores of a bag clogged with dust/powder particles reduce the motor's suction power and can cause damage.

1. Make sure the appliance is disconnected

from the electrical outlet.

2. Press the dust-compartment opening button

(13) to open the dust compartment lid (14).

3. Release the bag support (33) and remove

the Pure Clean dust bag (34). Dispose of the dust bag in compliance with all local regulations on waste disposal.

4. Slide a new Pure Clean dust bag into the

dust bag support completely; then place it back into the special compartment.

5. Close the dust compartment lid until it clicks

into place. If you are nding it difcult to close the dust compartment lid, it is likely that the Pure Clean dust bag and/or its dust bag support have not been assembled correctly. Do not force the dust bag lid to close, make sure both parts are in the correct position to allow lid closure. the motor lter) into the special dust- compartment guides.

5. Slide the Pure Clean dust bag into the dust

bag support all the way; then place it into the special dust compartment. The appliance is equipped with a safety device that prevents the dust compartment lid from closing unless the dust bag / container has been correctly installed.

6. Close the dust compartment lid until it clicks

into place. To use the vacuum cleaner with the dust container, remember to remove all the following parts: Pure Clean dust bag, dust bag support, gasket, motor lter and motor lter grill. CLEANING AND MAINTENANCE Before cleaning or maintaining the vacuum cleaner, make sure it has been unplugged from the electrical outlet. Do not use aggressive substances or abrasive materials to clean the appliance, its internal parts and attachments. Make sure it is thoroughly dry before using again. Cleaning the appliance Use a dry or slightly damp soft cloth to clean the plastic parts (body, dust compartment, exible hose etc) and the metal extension pipe (8). Cleaning the attachments Before cleaning the attachments refer to the chapter “Attachments”. Cleaning the dust compartment (F) For the routine cleaning of the dust compartment (38):

1. Press the dust-compartment opening button

(13) to open the dust compartment lid (14).

2. Based on the model, remove the Pure Clean

dust bag (34) or the dust container (39).

3. Clean the dust compartment by removing

any residual dirt with a small brush. If needed, use a damp soft cloth, taking care to wipe all its parts entirely dry.

special guides in the dust compartment.

14. Fit the Pure Clean dust bag using the special

dust bag support. The appliance is equipped with a safety device that prevents the dust- compartment lid from closing unless the dust bag has been correctly installed. Do not force the dust bag lid to close and make sure all the parts are in the correct position to allow you to close the lid.

15. Close the dust compartment lid until it clicks

into place. Cleaning the dust container (I) model without dust bag For the routine cleaning of the dust container:

1. Press the dust-compartment opening button

(13) to open the dust compartment (14) and remove the dust container (39).

2. Open the lid and empty the dust container.

3. Remove any residual dirt by washing the

dust container under running water.

4. Let it dry at room temperature until all its

parts are thoroughly dry.

5. Close the dust container lid until it clicks

into place and replace it into the dust compartment.

6. Close the dust compartment lid until it clicks

into place. Cleaning the lters (J) model without dust bag This model comprises two Pure Clean Hepa 13 lters. The Pure Clean Hepa 13 lter ensures maximum protection against allergens and high air quality, because the air given back by the appliance is entirely free from dust/powder residues (ltering power > 99.95 %). We advise you to clean the lter at least every 4 months to restore its ltering power. In any case we recommend replacing the lter at least every year to ensure maximum performance. To clean the Pure Clean Hepa 13 lter (30) in the back:

2. Remove the Pure Clean Hepa 13 lter by

Cleaning the lters (H) model with dust bag The Pure Clean Hepa 13 lter ensures maximum protection against allergens and maintains high air quality, as the air given back by the appliance is entirely free from dust/ powder residues (ltering power > 99.95 %). We advise you to clean the lter at least every 4 months to restore its ltering power. In any case we recommend replacing the lter at least every year to ensure maximum performance. To clean the Pure Clean Hepa 13 lter (30):

2. Remove the Pure Clean Hepa 13 lter by

releasing the opening tab.

3. Wash the lter under running water, taking

care that the jet of water is not too strong.

4. Hold it so that the water ows parallel to its

5. Let it dry at room temperature until all its

parts are thoroughly dry.

6. Replace the Pure Clean Hepa 13 lter,

paying attention to the position of the notches.

7. Fit the air grill into its housing until it clicks

into place. To clean the dust compartment lters (38):

8. Press the dust-compartment opening button

(13) to open the dust compartment lid (14).

9. Remove the Pure Clean dust bag (34), motor

lter grill (36) and motor lter (35) from the motor lter grill.

10. Clean the motor lter by washing it under

running water, taking care that the jet of water is not too strong. Then gently shake water loose.

11. When cleaning the motor lter grill, remove

any dust/powder residues with a small brush. If needed, use a damp soft cloth. Make sure all its parts are thoroughly dry before replacing them.

12. Fit the motor lter into the motor lter grill

again, taking care to position it gently into the special notches.

13. Slide the motor lter grill assembly into thehotpoint.eu

all the parts are in the correct position to allow lid closure.

19. Close the dust compartment lid until it clicks

into place. ATTACHMENTS The attachments can either be supplied as standard features (based on the model) or be purchased separately from Hotpoint authorised centres. Before changing an attachment, during maintenance, disconnect the plug from the electrical socket. Do not use aggressive substances or abrasive materials to clean the appliance, its internal parts and attachments. Make sure the appliance is thoroughly dry before using it again. Standard/Carpet brush (K) The standard/carpet brush (1) is suitable for vacuuming hard and smooth oors as well as carpets on a daily basis. Use the bristle- adjustment pedal (2) to clean: Hard oors Carpets To clean the plastic parts of the standard/carpet brush, remove the brush from the metal extension pipe (8) and wipe with a dry or slightly damp soft cloth. To clean the bristles, remove any dirt using, if needed, the precision nozzle (26). Parquet brush (L) The Parquet brush (3) is suitable for vacuuming delicate areas such as wooden oors. The special natural bristles enable you to use on very delicate surfaces without harm. To clean the plastic parts of the Parquet brush, remove the brush from the metal extension pipe (8) and wipe with a dry or slightly damp soft cloth. To clean the bristles, suck up any dirt using the precision nozzle (26). Turbo brush (M) The Turbo brush (4) is ideal for the in-depth vacuuming of short-pile carpets and removing pet hair. The rotation of the brush is operated by the vacuum cleaner's suction power.To clean the plastic parts of the Turbo brush, remove the brush from the metal extension pipe (8) and wipe with a dry or slightly damp soft cloth. Remove any releasing the opening tab.

3. Wash the lter under running water, taking

care that the jet of water is not too strong.

4. Hold it so that the water ows parallel to its

5. Let it dry at room temperature until all of it’s

parts are thoroughly dry.

6. Re-place the Pure Clean Hepa 13 lter,

paying attention to the positions of the notches.

7. Fit the air grill into its housing until it clicks

into place. To clean the dust compartment lters (38):

8. Press the dust-compartment opening button

(13) to open the dust compartment (14).

9. Remove the dust container (39).

10. Release the opening tab and then remove

the Pure Clean Hepa 13 lter, pre-lter (41) and lter protection grill (40).

11. When cleaning the lter protection grill,

remove any dust/powder residues with a small brush. If needed, use a damp soft cloth.

12. Clean the pre-lter by washing it under

running water, taking care that the jet of water is not too strong. Allow to dry.

13. Wash the Pure Clean Hepa 13 lter under

running water, taking care that the jet of water is not too strong.

14. Hold it so that the water ows parallel to its

15. Let it dry at room temperature until all its

parts are thoroughly dry. Make sure all its parts are thoroughly dry before replacing them.

16. Fit the pre-lter into the special indentation

of the Pure Clean Hepa 13 lter, locking both lters in place using the protection grill.

17. Fit the pre-lter, Pure Clean Hepa 13 lter

and protection grille assembly onto the dust container, paying attention to the positions of the notches, until it clicks into place.

18. Re-place the dust container into the dust

compartment. The appliance is equipped with a safety device that prevents the dust compartment lid from closing unless the dust container has been correctly installed. Do not force the dust bag lid to close it and make surehotpoint.eu

to be cleaned, thus ensuring maximum on fabrics. To clean the plastic parts of the Upholstery brush, remove the brush from the metal extension pipe (8) and wipe with a dry or slightly damp soft cloth. To clean the rotating bristles, release the lid by releasing its fastening elements, then disassemble the rotating brush and start cleaning. Remove any hairs or threads that got entangled using scissors, taking care not to damage the bristles. Precision nozzle (P) The precision nozzle in the attachment compartment (28) helps you vacuum corners, crevices and other difcult-to-reach areas. To clean the precision nozzle, remove the nozzle from the metal extension pipe (8) and wipe with a dry or slightly damp soft cloth. Nozzle for delicate surfaces (Q) The nozzle for delicate surfaces in the attachment compartment (28) is suitable for vacuuming surfaces requiring special care such as radiators, furniture etc. Its special natural bristles enable you to use it on very delicate surfaces without any harm. To clean the plastic parts of the nozzle for delicate surfaces, remove the nozzle from the metal extension pipe (8) and wipe with a dry or slightly damp soft cloth. To clean the bristles, remove any dirt using, if needed, the precision nozzle (26). hairs or threads that got entangled in the rotating brush using scissors, taking care not to damage the bristles. Deluxe Parquet brush (N) The Deluxe Parquet brush (5) is suitable for vacuuming delicate and parquet oors. The brush is equipped with very delicate rotating bristles, which are operated by the vacuum cleaner's suction power, and soft wheels protecting delicate oors. To clean the plastic parts of the Deluxe Parquet brush, remove the brush from the metal extension pipe (8) and wipe with a dry or slightly damp soft cloth. To clean the rotating bristles, turn the safety lock into position and remove, then disassemble the rotating brush and start cleaning. Remove any hairs or threads that got entangled using scissors, taking care not to damage the bristles. For your safety, never put your hands close to the suction nozzle or rotating brush while operating the appliance. Upholstery brush (O) The Upholstery brush (6) is suitable for vacuuming surfaces such as sofas, mattresses, blankets, cushions etc. It is equipped with rotating bristles operated by the vacuum cleaner’s suction power that enable you to clean in depth and remove any fur, hairs or mites from fabrics. The protection grill prevents the bristles from touching the surfaces

• The plug was not inserted or is not making contact.

• Change the dust bag. If large quantities of very ne dust/ powder are sucked up (e.g. our, etc), the full dust bag indicator may light up although the bag is not full yet. The reason is that the Pure Clean dust bag is able to retain very ne dust/powder particles, thus ensuring maximum hygiene.

• Clean the dust container in models without dust bag.

• Clean the lters and, if needed, replace them.

• Make sure the expansion pipe, exible hose and brush are not blocked.

• Clean the lters and, if needed, replace them.

• Make sure the expansion pipe, exible hose and brush are The vacuum cleaner cannot be switched on. The full dust bag/container indicator lights up although it is not full yet. Low suction power. TROUBLESHOOTING Problem Possible causes / Solutionshotpoint.eu hotpoint.eu

• Change the dust bag. If large quantities of very ne dust/ powder are sucked up (e.g. our, etc), the Pure Clean dust bag may become clogged.

• Clean the dust container and its lters.

• Battery not charged.

• The batteries were positioned incorrectly inside the battery compartment. Position the two AAA batteries making sure of the positive and negative poles.

• Remove batteries; then position them again, making sure of the positive and negative poles.

• Electronic appliances or obstacles may be interfering or shielding with the infrared signal.

• If very ne dust or powders are sucked up such as our, etc. small electrostatic discharges could occur. When sucking up materials previously mentioned, we advise not to use the metal extension pipe, but only the plastic exible hose and to set a low suction power level.

• One or more attachments were assembled incorrectly. Make sure the lters and brushes were assembled according to these instructions. In the model with dust bag make sure that the gasket is correctly in place too.

• The dust bag/container is full. Replace the dust bag or clean the dust container.

• Clean the lters and, if needed, replace them.

• The air regulator is open. Make sure it was closed correctly.

• The Pure Clean dust bag or dust container was assembled incorrectly. Make sure it is correctly in place so that the safety lever will let you close the dust compartment lid. Remote Power not working. Small electrostatic discharges occur while sucking up. The vacuum cleaner whistles or vibrates when in use. The dust compartment lid cannot be closed. and recycling of the materials they contain and reduce the impact on human health and the envi- ronment. The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

ELECTRICAL APPLIANCES The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsor- ted municipal waste stream. Old appliances must be collected sepa- rately in order to optimise the recoveryhotpoint.eu