Speedy 30JIL - Hand blender Aigostar - Free user manual and instructions

USER MANUAL Speedy 30JIL Aigostar

Exterior view of a kitchen brush and a glass of liquid (no text or symbols visible)

Model: 8433325504335

The material in contact with the food is PP (polypropylene) and Stainless Steel, free.

IMPORTANT SAFEGUARDS

Before using the electrical paliance, the following basic precautions should always be followed including the following:

1. Red all instructions.
2. Before using check that the vqeta of wall outlet opened to the one shown on theg patite.
3. Do noperate any appliance with a daged cord or plug or after the appliance malfunctions, r is dropped or damaged in any manner. Return appliance to the nearest author service facility for examination, pair electrical omechanical adjustment.
4. If the pply cord is damaged it must be replaced by the manufacturer or a authorized service gent to a qualified technician in order to avoid a hazard.
5. Uplug from outlet when not inbefore putting on or taking off parts, ad before cleaning. a l was disconnect theender from the spply if it is left unattended before assembling, disassembling or cleaning;
6. Do not letd hong over edge of t a b l e hoot surface.
7. Do not immerperupart oblender into wates this would giverisetoelectricshock.
8. Close pervision is necessary when your appliance is being used near children r infirm persons.
9. Avod contacting moving parts.
10. Keep hands and utensils out of container whelding to reduce the risk of severity in persons to damage to the blender. As proper may be used but must be used only when the blender is not running.
11. The appliance cannobe used for chopping ice oblending hard and dry substance, otherwise theade could be blunted.
12. To reduce the riskjury, nine vreplace cutting blade or base without firsputting bowl properly in place.
13. Be sure proper lid is secured locked in place before perating

appliance.

1. The use of accessor recommended by the manufacture may cause injuries to persons.

2. Do noperate the paliance for oththan its intended use.

3. This paliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concegnise of the possibilities by a person responsible for their safety.

4. Children should be supervised to ensure that ythe noplay with the paliance.

5. Do not use outdoors.

19.Save these instructions.

1. Take care p6tential injury from misuse.

2. Care shalbe taken when hangthe shar cutting blades, emptying the bowl ad during cleaning.

3. Switch off thepliance ad disconnect from sply before changing accessories approaching parts that move in use.

SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY

Know your blender (It is suitable for blending vegetable and fruit)

1 2 3 4 5 6

1. Speed knob
2. Lower speed button
3. High speed button
4. Lock
5. Blend rod
6. Cap
   The max capacity is 700ml

Using your blender

Before the first use, clean the blender according to the section of “quick cleaning”. The time running unit without load can’t exceed 15s.

Important: Blades are very sharp, handle with care. Ensure that the hand-held blender unplugged from the power outlet before assembling or removing attachments.

Instruction for blender

Max operation duration per time less than 30 seconds, and 3 minutes rest time mus maintained at two consecutive cycles.

1. To assemble the detachable shaft with the motor unit, turn the shaft anti-clockwise direction until tightened. To disassemble, just turn in the adverse direction.

2. Simply plug the hand-held blender to power outlet.

3. Lower the hand-held blender into food. Then press and hold the low speed button operating. At the same time you can select desired speed setting by dialing the speed dial, the speed will be higher gradually when you dial the speed control dial from left to right.

4. You also can start operating by pressing and hold the high speed button (turbo appliance will operate at the highest speed all the time. The speed will not change dial the speed control dial.

5. To stop the hand-held blender by releasing the low speed button or high speed

Caution:

-To reduce the risk of injury, never place cutting blade on base without first putting properly in place.

-Be sure chopper lid is securely locked in place before operating appliance.

- after chopping, for safety, you shall disassemble the motor unit from the chopper lid firstly,

then remove the chopper lid. Never remove the chopper lid with the motor unit in

CLEANING AND MAINTENANCE

1. Unplug the appliance and remove the detachable stem.

Note: Do not immerse the detachable stem of the blender in water because overtime lubrication on the bearings may wash away.

1. Wash the detachable stem under running water, without the use of abrasive clean detergents. After finishing cleaning the detachable stem, place it upright so that any which may have got in, can drain out. The stem is dishwashing safe component.

2. Wash the cup, bowl, beater and blade in warm soapy water. The bowl and the recommended to place in dishwashing machine as the plastic component deteriorates th prolonged use of dishwasher cleaning.

3. Wipe the motor unit with a damp cloth. Never immerse it in water for cleaning shock may occur.

4. Dry thoroughly.

Caution: Blades are very sharp, handle with care.

1. Reassemble the blender shaft to motor unit then place it upright hang it up for saving space.

Quick cleaning

Between processing tasks, hold the hand-held blender in the cup half filled with water on for a few seconds.

Environment friendly disposal

You can help protect the environment!

Please remember to respect the local regulations: hand in the non-working electrical equipments to an appropriate waste disposal center

WARRANTY: 2 YEARS

Labeled diagram of a laboratory apparatus with numbered parts for identification

Diagram of a laboratory apparatus with numbered parts, likely a cleaning or testing device.

Diagram of a laboratory apparatus with numbered parts, showing a funnel and cup assembly.

Technical diagram of a laboratory apparatus with numbered parts, likely a cleaning or testing device.

Labeled diagram of a laboratory apparatus with numbered parts, showing a funnel and cup assembly.

QR code image with a central logo, likely linking to a digital resource or website.

AIGOTECH ONSYNK, S.L..

C/LOS TRANSPORTISTAS N.43 NUMANCIA DE

LASAGRA 45230, TOLEDO, ESPAÑA.

C.I.F.:B-85712198

MADE IN P.R.C.