100 Performace - Iron TERMOZETA - Free user manual and instructions
Find the device manual for free 100 Performace TERMOZETA in PDF.
| Technical Specifications | Power: 2400 W, Ceramic soleplate, Tank capacity: 300 ml |
|---|---|
| Usage Features | Vertical steam, Anti-drip function, Temperature adjustment, Eco mode |
| Maintenance and Repair | Cleaning the soleplate recommended after each use, Regular descaling advised |
| Safety | Automatic shut-off after 8 minutes of inactivity, Overheat protection |
| General Information | Weight: 1.5 kg, 360 b0 swivel cord, Warranty: 2 years |
Frequently Asked Questions - 100 Performace TERMOZETA
Download the instructions for your Iron in PDF format for free! Find your manual 100 Performace - TERMOZETA and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 100 Performace by TERMOZETA.
USER MANUAL 100 Performace TERMOZETA
4. Steam control dial
6. Shotofsteambutton
7. Self-cleaning button
- After taking off the packing make sure that the appliance is intact. In case of doubt do not use it and contact an assistance centre authorised by TERMOZETA.
- Do not leave pieces of packing (plastic bags, polystyrene foam, nails etc.) within reach of children or persons with reduced mental capacities since these are potential sources of danger.
- The electrical safety of this appliance is ensured only if it is correctly connected to an effective earthing system in compliance with the existing electrical safety standards. TERMOZETA shall not be held responsible for any damage caused by the lack of an earthing system.
- Before connecting the plug to the outlet check that the working voltage of the appliance corresponds to the one in your house. If in doubt, contact professionally qualied staff.
- Use of adaptors, multiple outlets and extension leads is not advisable. In case of need use exclusively approved appliances in conformity with the current safety regulations while making sure that they are compatible with the appliance power. If in doubt, contact professionally qualied staff.
- Any installation which doesn’t comply with what is specied can endanger your safety and the warranty expires.
- The appliance must only be used to iron fabrics for domestic purposes.
- For safety reasons pay attention: - do not use the appliance when you are barefoot or having wet hands or feet - do not use the appliance outside the domestic environment - do not leave the appliance exposed to atmospheric agents (sun, rain, etc.) - never pull the power cord or the appliance itself in order to disconnect the plug from the outlet - do not leave the appliance unattended when it is plugged into the main power supply - never immerse the appliance in water or other liquidsENGLISH
- The appliance can be used by children aged from 8 and above and by people with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, only if they have been given supervision or instructions concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Keep the iron and its cord out of reach of children less than 8 years of age when it is supplied with power or when it is cooling down.
- The power cord of the appliance should never be replaced by the user himself. In case of necessity contact an assistance centre authorised by TERMOZETA or professionally qualied staff.
- In case of failure and/or malfunctioning of the appliance, turn it off and do not tamper with it. For any repairs contact an assistance centre authorised by TERMOZETA and ask for the use of original spare parts.
- At the end of the life cycle of the appliance, put it out of service by cutting the power cord after disconnecting the plug from the outlet. For the disposal of the appliance follow the regulations which are valid in your place of residence.
- Termozeta cannot be considered responsible for any damage to persons, animals or things caused by the incorrect installation or as a result of an illegitimate, mistaken or unreasonable use.
- Before and during use make sure the work surface is stable and heat resistant.
- Never leave the iron unattended when it is connected to the power supply.
- Do not use the iron if it has been dropped, if there are signs of damage or if water leaks.
- Do not try to iron clothes if they are worn by a person: the steam is very hot, you could cause serious burn injuries.
- Do not come into contact with the water coming out of the soleplate, since it is very hot and could cause burns.
- Before carrying out any cleaning operation, disconnect the plug from the power outlet and wait for the iron to cool down.SYMBOL FUNCTION DESCRIPTION Dry ironing No steam Steam ironing Steam level: minimum Steam ironing Steam level: maximum max Ironing using steam at high temperature (cotton, linen) Ironing at medium temperature (wool, silk) Ironing at low temperature (synthetic bres)
- Always proceed with this operation with the plug disconnected from the power outlet.
- Make sure the steam control dial (4) is in the “ ” position (dry ironing).
- Open nozzle (2) and ll the tank through the proper hole without exceeding the MAX level (13) indicated. Do not put any perfumed substances into the tank.
- While ironing, check the water level inside the tank. SUGGESTION If water in your area is particularly calcareous, it is advisable to use distilled water.
2• Fill the tank with water.
- Choose the desired steam output by turning the steam control dial (4). NOTE
- Steam is delivered only if knob (12) was set to symbols , max.
- When the iron is placed vertically during ironing pauses, the steam delivery is automatically cut off.
- Some water drops can come out together with the steam on rst use. This is to be considered normal. Before ironing your linen carry out some tests on an old cloth.
- Make sure the steam control dial (4) is in the “ ” position (dry ironing).
- Completely unroll the power cord (10), put the iron in a vertical position and connect the plug to the power outlet.
- With the temperature control knob (12) select the temperature which is most suitable for the type of fabric to be ironed.
- The thermostat light (9) turns on and will then turn off when the soleplate reaches the selected temperature. The iron is now ready for use. IMPORTANT
- Before and during use make sure the work surface is stable and heat resistant.
- Never leave the iron unattended when it is connected to the power supply.
- Do not use the iron if it has been dropped, if there are signs of damage or if water leaks. SUGGESTIONS
- First iron more delicate fabrics which require low temperature and then the more resistant ones which require higher temperatures.
- Before ironing pass the iron over a small hidden area of your item of linen to make sure the temperature selected is suitable for that type of fabric.
- Place the appliance on a rm at surface.
- Select the proper temperature by turning the control knob (12) on the iron.
- Completely unwind the power cord (10) and plug into the outlet.
- When the pilot light (9) goes out, the iron is ready for use.
- The pilot light (9) on the iron will light up and go out automatically while you are ironing to show that the soleplate is being kept at a constant temperature.
- When you have nished ironing to turn off the appliance. Let the iron cool down. FOR DRY IRONINGTo enable this function, press the super-steam button (4) several times: the iron will supply an instantaneous high power steam jet.
- Do not press button (4) too many times consecutively, as this may cause non-steamed water drops to be discharged.
- Use this function only with the temperature control knob (12) set to symbols , max.
- When the super-steam function is used for the rst time some limestone pieces could come out. We therefore recommend not to discharge the rst steam jets directly onto the linen. This system prevents the iron from dripping onto the linen. The device is automatically enabled if, for whatever reason, the temperature of the soleplate lowers. To “liven up” the clothes hung on cloth hangers, curtains, etc. you can use the iron vertically:
- Set the temperature control knob (12) to the max position.
- Hold the iron in a vertical position at a distance of about 15-20 cm from the fabric.
- Press the super-steam button (4) several times. NOTE
- Do not press the super-steam button too many times consecutively. Observe pauses of some seconds between one operation and the following one. IMPORTANT
- Do not use this function on fabrics made up of synthetic bres.
- Keep an adequate distance between the fabric and the iron soleplate in order to avoid burns.
- Use this function only on clothes hung on clothes hangers. Do not try to iron clothes if they are worn by a person: the steam is very hot, you could cause serious burn injuries. SUPER-STEAM FUNCTION ANTI-DRIP SYSTEM VERTICAL IRONING SPRAY FUNCTION
- This function allows moistening the linen during both steam and dry ironing.
- To enable it press the spray button (5) several times and direct the water jet onto the most resistant creases. ENGLISH• Disconnect the plug from the power outlet.
- Always set the steam control dial (4) to the “0” position.
- Let the iron cool down.
- Wind the cord around the rear part of the appliance.
- Place the iron in a vertical position. SELF-CLEANING SYSTEM AFTER USE WARNING! Before carrying out any cleaning operation, disconnect the plug from the power outlet and wait for the iron to cool down.
- Clean the iron body only with a soft and dry cloth.
- Clean the soleplate using a non-abrasive sponge in order not to damage the soleplate surface.
- Do not use chemical or abrasive substances.
- Do not immerse the appliance in water or other liquid substances.
CLEANING AND MAINTENANCE
ENGLISH Your iron is supplied with a self-cleaning system which allows to reduce the formation of limestone deposits. In order that it produces its benets it is necessary to regularly effectuate the operation, at least once a month. Proceed as following:
- Set the dry ironing function.
- Fill up the tank up to MAX level
- Make the iron function as normal bringing the plate to the maximum temperature.
- Disconnect the plug from the current socket when the iron is ready.
- Holding down the self-cleaning button (7) wag the iron in horizontal position, above a sink or a basin. Let the tank get empty. The water-steam mixture will eliminate a part of limestone residues present in the plate.
- Afterwards connect the plug to the current socket and moving the iron above an old cloth, eliminate all the residue water present in the plate. Important: Pay attention not to get in contact with the water that is comes out from the plate since it is bowling and you could get burned. Note: Before re-using the iron to iron the clothing, pass the cold plate on a dry cotton cloth.TermozetaS.p.A.reservestherighttointroducetechnicaland/oraestheticchangestoitsproducts intended to improve performances. Termozetaisaninternationaltrademark.Copyright©1995.Allrightsreserved. TermozetaS.p.A.-ViaMagenta,41/43-20010Bareggio(MI)Italy
INFORMATION FOR USERS
In accordance with European Directives 2011/65/CE, 2002/96/CE and 2003/108/CE on the restriction of the use of dangerous substances in electric and electronic equipment as well as their waste disposal.
- Theadequateseparatecollectionforthesubsequentstart-upoftheequipmentsenttoberecycled,tre- ated and disposal of in an environmentally compatible way contributes to preventing possible negative effectsontheenvironmentandhealthandoptimisestherecyclingandreuseofcomponentsmakingup theapparatus.
ManualGo.com