BW700 - Bottle warmer ALECTO - Free user manual and instructions

Frequently Asked Questions - BW700 ALECTO

USER MANUAL BW700 ALECTO

Power consumption: 500 Watts

Operational ambient temperature: between +7^ and +37^

Heating system: PTC with temperature controlled protection

24 months guarantee

GB

SPECIFICHE TECNICHE

The final temperature of the milk or food is determined by the amount of water in the bottle warmer. If the temperature is too high, it is recommended to use less water in the bottle warmer. In case the temperature is too low, use more water.

It is advised to regularly take out the bottle or pot and shake or stir well for an even heating of the content.

IMPORTANT SAFEGUARDS

• Read and save these instructions.
• Never use the unit without water in it.
• Do not move an appliance containing hot liquids.
• Do not immerse appliance, cord or plugs in water or other liquid.
• Place the Baby Bottle Warmer out of the reach of children and on a dry, non-slip, horizontal surface.
• Close supervision is necessary when the unit is used near children.
• Do not let cord hang over edge of table or counter.
• Do not place on hot surfaces or in a heated oven.
• Only use the Baby Bottle Warmer when the ambient temperature is between +7^ and +37^ .
• Change the water in the bottle warmer each time after use for hygienic reasons.
• Watch out for hot water splashes when the water is boiling. For protection, place the steam cover on the bottle warmer.

OPERATION

To quickly warm up:

1. Place the bottle warmer on a stable surface, out of reach of children.
2. Pour 50ml of water into the bottle warmer.
3. Place the jar (without lid) or bottle into the bottle warmer.
4. Insert the plug into a 230Volts wall socket.
5. Press the button to switch on the bottle warmer.
6. Now within 5 seconds, use the M button to select:

use the V or button to increase or decrease the recommended warm-up time, see the next page

1. 5 seconds after making your selection the heating element of the bottle warmer will switch on while the display starts counting down to 0.

2. When the countdown reaches 0:00, the display starts flashing for 1 minute. During this minute, leave the jar or bottle in the warm water.

Depending on the amount of milk or food, the initial temperature and the material of the bottle or jar, you may have to adjust the warm-up time.

The following chart only serves as a reference:

Amount of milk:	Food at room temperature		Food from the fridge
	Plastic	Glass	Plastic	Glass
60ml	2:00	1:40	2:16	2:05
90ml	2:03	1:50	2:37	2:15
120ml	2:22	2:10	3:20	3:03
150ml	2:30	2:18	3:46	3:25
180ml	2:35	2:22	4:10	3:55
210ml	3:00	2:40	4:25	4:06
240ml	3:15	3:00	4:40	4:25
270ml	3:20	3:05	4:55	4:38
jar:
120gr	2:20		3:10
200gr	2:30		4:00

1. After this minute 5 beeps are emitted while the bottle warmer switches itself off.
2. Remove the bottle/jar from the bottle warmer and shake the milk or stir the food to ensure an even temperature.

3. First check the temperature of the food with the back of your hand before feeding your baby, to ensure the food is at a temperature that's safe for your baby.

4. If the temperature is too low, briefly put the bottle or jar back into the warm water of the bottle warmer. You don't have to switch the device on again. The water will still be warm enough. Perhaps next time you could increase the warm-up time somewhat.

5. If the temperature is too high, let the milk or food cool down and next time set a somewhat shorter warm-up time.

To slowly heat up:

1. Place the bottle warmer on a stable surface, out of reach of children.
2. Place the jar (without lid) or bottle into the bottle warmer.
3. Fill up the space between the bottle warmer and the bottle or jar with tap water at room temperature. Fill with water until you reach the same level as the milk or food in the jar. When filling, never exceed the maximum mark indicated.
4. Insert the plug into a 230Volts wall socket.
5. Press the button to switch on the bottle warmer.

1. Now within 5 seconds, use the M button to select:
2. Use the button to select the starting temperature; or food at room temperature or food from the fridge.
3. 5 seconds after making your selection the heating element of the bottle warmer will switch on while the display starts counting down to 0.
4. When the warm-up time is finished, 5 beeps are emitted and the bottle warmer will switch itself off.
5. Remove the bottle/jar from the bottle warmer and shake the milk or stir the food to ensure an even temperature.

6. First check the temperature of the food with the back of your hand before feeding your baby, to ensure the food is at a temperature that's safe for your baby.

7. If the temperature is too low, briefly put the bottle or jar back into the warn water of the bottle warmer. You don't have to switch the device on again. The water will still be warm enough. The next time you may want to pour some more water into the bottle warmer.

8. If the temperature is too high, let the milk or food cool down and the next time pour a little less water into the bottle warmer.

To defrost:

1. Place the bottle warmer on a stable surface, out of reach of children.
2. Place the jar or bottle with the frozen food into the bottle warmer.
3. Fill up the space between the bottle warmer and the bottle or jar with tap water at room temperature. Fill with water until you reach the same level as the milk or food in the jar. When filling, never exceed the maximum mark indicated.
4. Insert the plug into a 230Volts wall socket.
5. Press the button to switch on the bottle warmer.
6. Now within 5 seconds, use the M button to select
7. 5 seconds after making your selection the heating element of the bottle warmer will switch on while the display starts counting down to 0.
8. After the 20 minutes defrosting time, 5 beeps are emitted and the bottle warmer switches itself off.

To sterilize pacifiers:

1. Place the bottle warmer on a stable surface, out of reach of children.
2. Pour 65ml of water into the bottle warmer. (see the short marking mark)
3. Put the pacifiers you'd like to sterilize down into the bottle warmer.
4. Place the steam cover onto the bottle warmer to both keep the heat inside and to prevent hot splashes from harming you.

KEEP IN MIND THAT THIS STEAM COVER

MAY BECOME VERY HOT DURING USE.

1. Insert the plug into a 230Volts wall socket.
2. Press the button to switch on the bottle warmer.
3. Now within 5 seconds, use the M button to select the option
4. 5 seconds after making your selection the heating element of the bottle warmer will switch on while the display starts counting down to 0. During the sterilizing process, the display icon will rotate.
5. After the 5 minutes sterilizing time (or longer, the sterilizing lasts until all the water is evaporated), 5 beeps are emitted and the bottle warmer switches itself off.
6. Attention: the steam cover may become very hot. First wait several minutes until the temperature has decreased sufficiently for you to safely remove the steam cover. Use kitchen pliers (not included) to remove the pacifiers from the bottle warmer.

MAINTENANCE INSTRUCTIONS

Cleaning:

Disconnect the Baby Bottle Warmer from the mains socket (or the cigarette lighter socket) and allow it to cool down. Clean the container and the outside of the Baby Bottle Warmer with a damp cloth. Never immerse the Baby Bottle

Warmer in water. Do not use cleaning orscouring agents.

Decalcify:

Hard water deposits must be removed. To do this use white vinegar only. Pour the vinegar into the tank at mid-level, allow to rest until the hard water deposits have been completely eliminated. Rinse well and wipe with a damp

cloth.

Warning:

If a fault occurs, consult the Alecto service centre at www.ALECTO.NL. Under no circumstances should you try to repair the Baby Bottle Warmer yourself; do not dismantle. Servicing should be performed by qualified service

personnel only.