GV36FAB - Fireplace FABER - Free user manual and instructions

Product type	Gas fireplace
Brand	Faber
Model	GV36FAB
Power source	Gas
Control	Manual and remote control (optional)
Flame adjustment	Button B for flame height
Pilot light	Manual ignition via button A
Safety	Safety device in case of flame extinguishment
Remote control batteries	2 AAA/LR03 alkaline batteries, lifespan ~1 year
Glass cleaning	Soft cloth or ceramic hob cleaner
Safety distance	100 cm minimum from flammable materials
Installation	By approved installer, compliance with local standards
Annual maintenance	Chimney cleaning by a professional
Recycling	Recyclable packaging, batteries to be disposed of separately

Frequently Asked Questions - GV36FAB FABER

How to light the pilot light?

Press button A and turn it to the left to the small flame position. A spark occurs. Hold it down for a few seconds until the pilot light ignites, then hold for another 10 seconds before releasing.

How to adjust the flame height?

Use button B to adjust the flame height between the pilot and full position. The remote control can also adjust the height.

What to do if the pilot light goes out?

Wait at least 5 minutes before relighting. Check that there is no malfunction of the gas system or venting. If this happens regularly, contact your installer.

How to use the remote control?

First turn on the fireplace manually. Then use the large flames or small flames button on the remote. The receiver beeps if the signal is received.

How to replace the remote control batteries?

Remove the back cover, gently pull the battery clip, insert 2 AAA/LR03 alkaline batteries, then reassemble. If necessary, re-pair the receiver.

How to clean the glass?

Wait for the appliance to cool down. Open the door by unscrewing the lock. Use a soft cloth or a ceramic hob cleaner. Avoid fingerprints.

What safety distances to observe?

Do not place flammable materials within 100 cm of the appliance. Use a fire screen if children or elderly people are present.

Can I use the appliance during or after renovations?

No, wait until the renovation work is dry. Air drafts can draw in paint or construction residues that deposit as soot on cold surfaces.

Who should install the appliance?

Installation must be carried out by an approved installer in accordance with local gas, ventilation, and venting regulations.

How to dispose of the appliance at the end of its life?

Remove the remote control batteries and dispose of them separately. The packaging is recyclable. Contact your local authorities for the best disposal method.

USER MANUAL GV36FAB FABER

Hand service and remote control

2.1 Safety instructions for the user 7
2.2 (Manual)control 8
2.3 Remote control (optional) 9
2.4 Battery replacement transmitter 9
2.5 Cleaning and service instructions 9
2.6 Disposal of packaging and appliance 10

1.2.4 Hoofbrander doven

2.1 Safety instructions for the user

• If a gas leak is found or suspected, turn off the gas supply at the meter and contact your installer or gas emergency service
  These instructions should be read carefully and retained for future reference
• Remove any stickers, protection foil and protection rubber of the glass
• Do not use the fire with a broken or damaged glass
• The fire has a safety device which turns off the gas supply if there is a build up from flue gasses in the combustion room or a temporary gas cut-off. Wait at least 5 minutes before turning the appliance on again. Contact a qualified installer when the appliance goes off regularly
• Since the appliance has been designed for heating purposes all surfaces, including the glass, can become very warm (over 100^ ). An exception to this is the lower side of the door and the control buttons
• Due to the newness of materials, they may give off a slight smell for a period after initial lighting. This is normal, odours will disperse after a few hours use
• Do not place curtains, clothing, laundry, furniture or other flammable materials near the appliance. The required minimum distance is 100cm
• Switch off the receiver of the remote control if you don't use the fire for a long time. Do not let children use the remote control without supervision

IMPORTANT: A suitable Fireguard conforming to BS6539 and BS6778 should be used with this appliance to protect children, the elderly or infirm. Care should also be taken with pets. In your own interest and that of safety, all gas appliances must be installed by competent persons. Installation must be in accordance with National Regulations. CORGI registered installers are required to work to recognised standards. See also the installation guide.

Note: Since the appliance is a source of heat, circulation of air occurs. Therefore it is of importance that you do not use the appliance shortly after a renovation of the home. Due to the natural circulation of air, moist and volatile components from paint, building materials, carpet etc. will be attracted to the lit fire. These components can settle onto cold surfaces in the form of soot. As on all heat producing appliances, soft furnishings such as blown vinyl wallpaper placed too near to the appliance may become scorched or discoloured. This should be born in mind when installing the appliance.

2.2 (Manual)control

Depending on the model, the gas control block is positioned either:

behind a stainless steel door on the underside of the appliance
- mounted in the middle of the floor plate of the appliance
- behind the frame (accessible by tilting the frame upwards)

These appliances are fitted with a manual GV36 gas control (see fig.2.1) that optionally can be adjusted with a G30 remote control.

The pilot light always has to be lit before the main burner can be used. Rotary knob A functions as a main valve and has to be used to lit the pilot light. Use rotary knob B to adjust the height of the flames.

Warning! When the pilot extinguishes, for whatever reason, you should wait at least 5 minutes before trying again. Possible causes of pilot extinguish are:

• operation error
• interference of the safety device
• failure in the pilot flame system

Contact a qualified installer when the appliance extinguishes regularly.

2.2.1 Pilot ignition

To ignite the pilot light:

• simultaneously press and turn rotary knob A anti-clockwise to the (small flame) position at the (spark) position a click will be heard and the piezo-electric element starts to ignite
• hold the knob in this position for some seconds to clear the air from the pipe and allow gas to reach the pilot burner
• if the pilot light does not light return to the ● (stop) position and restart
  hold the knob for about ten seconds after the pilot light ignites
• turn the knob anti clockwise to the (large flame) position to allow the main burner to be ignited (see main burner ignition)

2.2.2 Pilot extinguish

To extinguish the pilot light:

• first turn rotary knob B clockwise till the (off) position
• turn rotary knob A clockwise to the (small flame) position
  simultaneously press and turn rotary knob A clockwise to the (off) position

2.2.3 Mainburner adjustment

To adjust the flame height turn rotary knob B between the (off) position and (large flame) position

2.3 Remote control (optional)

This version of the remote control is only meant to adjust the height of the flames. It only functions when the pilot burner is ignited and knob A is in the (large flame) position. Therefore it isn't possible to ignite the pilot flame with the remote control or to extinguish the pilot flame. The radio-frequency remote control is intended for fireplaces installed in a domestic setting in all EU countries except Austria, Denmark, Finland and Greece.

2.3.1 Transmission code

The transmission code of the remote control is already set at the factory and can not be adjusted by the customer.

Adjust the mainburner

First always ignite the pilot light (see 2.1.1 pilot ignition) and turn the rotary knob to the (large flame) position.

Adjust the fire as desired with the buttons at the remote control (see figure 2.2):

• use the button to raise the flames
• use the button to lower the flames

2.4 Battery replacement transmitter

• remove the cover on the back of the remote control to access the battery compartment
• carefully remove the batteries. Pay attention not to pull the wires
• replace with one alkaline 9V MN1604 or 6LR61 battery
• replace the cover

2.5 Cleaning and service instructions

• Turn off the fire and allow it to cool down before commencing cleaning.
• It is recommended that the fire is inspected/ serviced, by a competent person at least once a year.
• To maintain the finish on the trim wipe with soft damp cloth only. Do not use abrasive cleaners, polish or solvents as these can damage the surface finish.
• In case of a B1 appliance always sweep the flue at least once a year

2.6 Disposal of packaging and appliance

The appliance packaging is recyclable. The packaging could include the following materials:

cardboard
CFC-free foam (soft)
- wood
plastic
paper

These materials should be disposed responsibly and in conformity with government regulations.

Batteries are considered chemical waste. The batteries should be disposed of responsibly and in conformity with government regulations. Remove the batteries before disposing of the remote control.

Information on how to responsibly dispose of discarded appliances can be obtained from local authorities.