KH 2286 - Alarm Clock EBENCH - Free user manual and instructions

Product type	Radio alarm clock
Brand	EBENCH
Model	KH 2286
Power supply	Mains 220–230 V ~ 50 Hz
Backup battery	9 V (type 6LR61, not included)
Display	Red LED
Wavebands	FM (88–108 MHz) and AM (530–1600 kHz)
FM antenna	Flexible wire antenna
AM antenna	Built-in ferrite
Alarm function	Buzzer or radio
Alarm repetition (snooze)	Yes, approx. 9 minutes
Sleep function	Yes, up to 1 h 59 min
Settings backup	Via 9 V battery during power outage
Dimensions (approx.)	20 × 15 × 10 cm
Weight (approx.)	0,5 kg
Care	Dry cloth only
Repairs	Refer to authorized service center

Frequently Asked Questions - KH 2286 EBENCH

How to set the time on the KH 2286 radio alarm clock?

Press and hold the TIME SET button and simultaneously press the HOUR and MINUTE buttons until the desired time is displayed.

How to set the alarm?

Simultaneously press the ALARM, HOUR and MINUTE buttons to set the alarm time. Then, set the function switch to BUZZ for a sound alarm or to AUTO to be woken by the radio.

How to use the sleep function?

Press the SLEEP button. The display shows 0:59. To reduce the duration, press SLEEP and MINUTE; to increase it (up to 1:59), press SLEEP and HOUR. To stop, press the alarm repeat button.

Is the backup battery included?

No, the 9 V battery is not included. It is recommended to install one to keep settings in case of power outage.

What to do in case of power failure?

If a 9 V battery is installed, the alarm clock continues to operate in emergency mode (the LED display is off). When power returns, the correct time is displayed automatically.

How to clean the device?

Unplug the device and clean it only with a dry cloth. Never use cleaning products or water.

Can I use the device without a battery?

Yes, the device operates on mains power without a battery. In case of power outage, settings will be lost if no battery is installed.

How to switch from FM to AM band?

Use the band selector switch (FM/AM) located on the back of the device. Set it to FM or AM as desired.

Why is the display flashing?

A flashing display usually indicates that the time is not set or the backup battery is low. Set the time and replace the battery if necessary.

How to turn off the alarm once it goes off?

To stop the alarm completely, set the function switch to OFF. For a temporary interruption (snooze), press the alarm repeat button.

USER MANUAL KH 2286 EBENCH

Operating instructions

①Function switch (BUZZ (ALARM)/AUTO/ON/OFF) Controls
②LED display
③Snoopze button
④ Sleep button
⑤Alarm
⑥ Alarm off button
⑦ Hours
(8)Minutes
⑨ Time setting button (TIME SET)
Volume control
Tuner
② Band selector MW/VHF (AM/FM)
⑬ Battery compartment (in event of mains power failure)

· Operate the device at the correct mains voltage only Safety advice (220 / 230 Volt 50 Hz).
- Exposing this type of electrical equipment to high temperatures or moisture could lead to fires or electric shock. To prolong the service life of your radio do not position it near water or heating radiators. Always find a place with good air circulation.
- Never use damaged electrical equipment (the device itself or its mains lead).
- Do not try to reach the appliance if it falls into water. Pull out the plug from the mains socket immediately.
- The electrical components in this device are at high voltage. Never remove any parts of the housing.
- If repairs are required please take or send the device to our customer services centre (See the guarantee card for the address and telephone number).
- When required, the housing can be cleaned with a soft cleaning cloth (after ensuring that the plug is out of the mains

socket). Never use cleaning agents as they could damage the housing.

Connecting to mains	Insert the plug into a mains socket (make sure the mains voltage matches that of the device).
Radio reception	Switch on the radio by moving the function switch ⑨ into the ON position. Set the band selector switch to the required position (VHF or MW) ⑫. Set the volume using the volume control ⑩. Set the radio to the VHF or medium wave frequency of your choice using the tuner ⑪.
Aerials	FM (VHF): Unwind and position the wire aerial for best reception of VHF. AM /MW: The radio has a sensitive ferrite aerial.
Setting the time	Press and hold down the TIME button ⑨ (TIME / TIME-SET) whilst pressing the HOURS ⑦ or MINUTES ⑧ button until you see the correct time in the display.
Setting the alarm time	Press the ALARM ⑤ and HOURS ⑦ or MINUTES ⑧ button until the required alarm time appears in the display.
Setting the alarm mode	1 First set the required alarm time as explained above. 2 If you wish to be woken by the buzzer set the FUNCTION SWITCH ① to BUZZ (ALARM). The activated alarm mode is then shown in the display.
	· If you wish to be woken by the radio, set the FUNCTION

SWITCH to ON and select the desired station/frequency and the volume ⑩.

3 Then set the FUNCTION SWITCH ① to AUTO. The activated alarm mode is then shown in the display.
4 Then set the FUNCTION SWITCH ① to RADIO. The activated alarm mode is then shown in the display.

The appropriate alarm sounds when the alarm time is reached. The alarm sound switches off automatically after 1 hour 59 minutes.

The alarm sound can be temporarily interrupted by pressing the SNOOZE button ③ . After approximately 9 minutes the alarm sound automatically switches itself on again. This process can be repeated for a maximum of 1 hour 59 minutes. You can cut short the alarm period by setting the FUNCTION SWITCH ① to OFF.

After the alarm is switched off, if you set the FUNCTION SWITCH ① to AUTO again the alarm will sound on the next day at the same time.

Automatic 24 hour alarm

This setting allows you to go to sleep whilst listening to the radio. With the FUNCTION SWITCH ① in the AUTO or OFF position the radio plays for a maximum of 1 hour 59 minutes.

Going to sleep with the sleep function

1 Press the Sleep button ④ to set the time for which the radio will play. The display shows 0:59
2 If you wish the radio to stop playing earlier just press and hold down the Sleep button ④ whilst pressing the MINUTES ⑧ button until the desired playing time is displayed.

3 If you wish the playing time to be extended to 1:59, press and hold down the Sleep button ④ whilst pressing the HOURS ⑦ button.
4 To switch off the Sleep function ① or to set the sleep time to press the SNOOZE button ③.

NOTE: Pressing the Sleep button ① again after setting the sleep time will automatically reset the sleep time to 0. Press the SNOOZE ③ button to switch off the Sleep function.

Mains power failure

To guard against losing your settings in the event of a mains power failure insert a 9-volt battery into the battery compartment. The battery ensures that the radio alarm clock will function in emergency mode even during a mains power failure. In these circumstances the LED display ② will not be illuminated. Once mains power is restored the correct time will be automatically displayed again.

Note: The alarm, radio and LED ② display do not function during battery operation.

• Insert the battery into the battery compartment (see Fig. ⑬).
• Replace the battery annually.

Bochum, Germany, hereby declare that this product conforms

with the following EC regulations:

Statement of conformity

EC low voltage regulations, Electromagnetic compatibility,

Applicable harmonised standards.

Type/Description: Radio alarm clock KH 2284,

KH 2285, KH 2286, KH 2287

Bochum, 31.05.2003

Hans Kompernaß

• Managing Director -

Mode d'emploi

XPONOIAKO
INTHE ME
PAIOΦΩNO
"SLEEP"

Hpuoian autn eipentnTv akpoad npaoov
Eknouw evw oac naipveo unvoC.
H diapkia aIeitoupyiaoc Tou paoowou avepxetai e y.
1 wpa kai 59 aeT, av yupioe to IAKONTH
AEITOYPIA 工 ortn thc AUTO n OFF.

Somnamed radio,Sleep"