HC5410 - Tondeuse à barbe PHILIPS - Free user manual and instructions

USER MANUAL HC5410 PHILIPS

Always here to help you

Register your product and get support at

Congratulations on your purchase and welcome to Philips! To fully

benet from the support that Philips offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

2 Length setting adjuster

5 Beard comb 1-23mm (HC3410/17 only)

6 Beard comb 1.5mm (HC5410/83 only)

7 Beard comb 3mm (HC5410/83 only)

9 Socket for small plug

11 Case (HC5410/83 only)

12 Scissors (HC3410/13 only)

Read this user manual carefully before you use the appliance and save it for

- Keep the adapter dry.

- The adapter contains a transformer. Do not cut off the adapter to

replace it with another plug, as this causes a hazardous situation.

- This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

- Children should be supervised to ensure that they do not play with the

- Never immerse the appliance in water or rinse it under the tap. Only

the cutting unit can be rinsed under the tap.

- Use, charge and store the appliance at a temperature between 5°C

- Only use the adapter supplied.

- If the adapter is damaged, always have it replaced with one of the

original type in order to avoid a hazard.

- Do not use the appliance if the cutting unit or the trimming comb is

damaged or broken, as this may cause injury.

Electromagnetic elds

This Philips appliance complies with all standards and regulations regarding

exposure to electromagnetic elds (EMF).

- The appliance is equipped with an automatic voltage selector and is

suitable for mains voltages from 100 to 240 volts.

- The adapter transforms 100-240 volts to a safe low voltage of less than

Note: This appliance can only be used directly from the mains.

Preparing the appliance

1 Make sure the appliance is switched off.

2 Insert the appliance plug into the appliance (1) and put the adapter in

the wall socket (2).

The hair length settings are indicated in millimeters, the comb cuts the hair

to a length of 1mm to 23mm. The settings correspond to the remaining

hair length after cutting.

When you trim for the rst time, be careful. Do not move the trimmer

too fast. Make smooth and gentle movements.

Tip: Start trimming at a high length setting and reduce the length setting

gradually until you have reached the desired hair length.

1 Attach the comb onto the appliance.

ENGLISH 72 Turn the length setting adjuster to the desired length setting.

Note: When you trim for the rst time, start at the highest length setting to

familiarise yourself with the appliance.

3 Switch on the appliance.

4 To trim most effectively, move the trimmer against the hair growth

direction. Make sure the surface of the comb always stays in contact

Trimming without comb

Use the trimmer without the trimming comb to clip hair close to the skin

(0.5mm) or to contour the neckline and sideburns.

Be careful when you trim without comb because the cutting

element removes every hair it touches.

1 Push the comb off the appliance.

2 Switch on the appliance.

ENGLISH83 Make well-controlled movements. Touch the hair lightly with the

Using the beard comb (HC5410/83, HC3410/17 only)

- The hair length settings are indicated in millimeters.

HC3410/17: One adjustable beard comb that cuts the hair to a length of

HC5410/83: Two xed lengths beardcombs that cuts the hair to a length of

1 Attach the comb onto the appliance.

2 HC3410/17 only: Turn the length setting adjuster to the

desired length setting.

3 Switch on the appliance.

ENGLISH 94 To trim most effectively, move the trimmer against the hair growth

direction. Make sure the surface of the comb always stays in contact

Never use scouring pads, abrasive cleaning agents or aggressive liquids

such as alcohol, petrol or acetone to clean the appliance.

Never immerse the appliance in water or rinse it under the tap.

Note: Only the cutting element and the comb can be cleaned with water.

1 Make sure the appliance is switched off and disconnected from the

2 Wipe the housing of the appliance with a dry cloth.

3 Remove the comb and clean it with the brush or rinse it under the

4 Press the release button (1). The cutting unit comes off the appliance

5 Clean the cutting unit with the brush or rinse it under the tap.

6 Clean the inside of the appliance with the brush.

Never immerse the appliance in water or rinse it under the tap.

7 Shake off excess water. To reattach the cutting unit, insert the lug of

the cutting unit into the guiding slot.

ENGLISH108 Insert the lug of the cutting unit into the guiding slot (1) and push

the cutting unit back onto the appliance (2).

Only replace a worn or damaged cutting unit with an original Philips cutting

unit, available from authorised Philips service centres.

1 Press the release button (1). The cutting unit comes off the appliance

2 Insert the lug of the new cutting unit into the guiding slot (1) and

push the cutting unit back onto the appliance (2).

Ordering accessories

To buy accessories or spare parts, visit www.shop.philips.com/service

or go to your Philips dealer. You can also contact the Philips Consumer

Care Centre in your country (see the worldwide guarantee leaet for

- Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment.

ENGLISH 11Guarantee and support

If you need information or support, please visit

www.philips.com/support or read the separate worldwide