1171250501 - Lighting BRENNENSTUHL - Free user manual and instructions

USER MANUAL 1171250501 BRENNENSTUHL

LCN130PIRIP44 30W(1x30W) IP44Ja220,5x180,5x4mm

LCN 150 IP65 50 W (1 x 50 W) IP65 Nein 281,5 x 231 x 4 mm

LCN150PIRIP44 50W(1x50W) IP44Ja281,5x231x4mm

LCN 180 IP65 80 W (1 x 80 W) IP65 Nein 303,5 x 225,5 x 5 mm

Please note: Please read these instructions carefully prior to mounting the light and store them in a safe location afterwards!

SPECIFICATIONS

Protection class: I

Nominal voltage: 220 - 240V 50Hz

Model: Output: Type of Motion Protective cover protec-detector dimensions: tion:

L CN 110 IP65	10 W (1 x 10 W)	IP65	no	110.5 x 83 x 4 mm
L CN 110 PIR IP44	10 W (1 x 10 W)	IP44	yes	110.5 x 83 x 4 mm
L CN 130 IP65	30 W (1 x 30 W)	IP65	no	220.5 x 180.5 x 4 mm
L CN 130 PIR IP44	30 W (1 x 30 W)	IP44	yes	220.5 x 180.5 x 4 mm
L CN 150 IP65	50 W (1 x 50 W)	IP65	no	281.5 x 231 x 4 mm
L CN 150 PIR IP44	50 W (1 x 50 W)	IP44	yes	281.5 x 231 x 4 mm
L CN 180 IP65	80 W (1 x 80 W)	IP65	no	303.5 x 225.5 x 5 mm

The heavy-duty LED light is suitable for indoor and outdoor lighting applications and is designed for permanent installation. Do not use this light for any other purposes.

SAFETY NOTES

1. The light must be installed and serviced by a qualified technician.
2. Always turn off the power supply before installing or servicing the light.
3. The light must be properly earthed.
4. Do not use this light without properly attached gaskets!
5. LED lights are extremely bright! Avoid looking straight into an LED light beam, as doing so could result in irreversible eye damage.
6. Damaged protective covers must be replaced with an original Brennenstuhl protective cover before the light can be used again.

1. If the mains supply cable of the light is damaged it must be replaced by a qualified technician in order to avoid risks.

MOUNTING AND CONNECTION TO THE POWER SUPPLY

1. Do not attach the light to a surface that is subject to vibrations.
2. Mounting position: If possible the light should be mounted using the wall bracket. Lights with a motion detector must be mounted as shown in Fig. 1.
3. Mark the position of the bore-holes that are needed to attach the wall bracket and drill the required holes in the wall. Attach the bracket to the wall using suitable screws.
4. Open the light's terminal box.

GB Operating Instructions Chip LED Light

1. Guide the connecting cable through the cable gland and connect it to the light's lustre terminal as shown in Fig. 2 (left image shows 10W version, right image shows 30W version and higher. N = blue cable, earthing symbol = green / yellow cable, L = brown cable).
2. Make sure the cable is securely fastened in the cable gland.
3. Replace the cover of the terminal box. Make sure the gasket is seated correctly.
4. Fasten the light to the wall bracket using the screws and nuts included with the package. Set the light to the desired position and tighten the screws.

DESCRIPTION OF OPERATION

(For Versions with a Motion Detector)

The light is equipped with an infrared sensor. It turns on automatically whenever the sensor detects movement in its vicinity

Try not to aim the motion detector in the direction of swimming pools, heater vents, air conditioners or objects which are subject to large variations in temperature. Avoid pointing the motion detector at trees or shrubs and at areas where pets like to move about.

Make sure when mounting the light that the motion detector is most sensitive to things that move through its detection range from side to side and least sensitive to things that move straight at the device.

ADJUSTING THE MOTION DETECTOR

There are three knobs on the underside of the light (see Fig. 3).

Setting the time (TIME):

Use the TIME knob to set how long the light remains on after the last movement (between 10 seconds and 4 minutes). Turn the TIME knob clockwise to increase the time span.

Sensitivity (SENS):

This knob can be used to adjust the sensitivity of the sensor. Turn the SENS knob clockwise to increase sensitivity.

Light Setting (LUX):

The LUX setting determines how dark it must be before the sensor turns on the light. The sun symbol (丰) shows that the sensor is active during the day and at night. If the knob is set to moon () , the sensor only works at night. To adjust the sensor, wait until the desired level of ambient light has been reached. Turn the knob all the way to the moon symbol () , then turn the knob slowly towards the sun symbol (丰) until the light turns on if movement is detected.

The light will thereafter turn on automatically at the preset level of darkness whenever a movement is detected.

Motion detector: passive infrared sensor

Detection range: up to 12m /up to 180^ (horizontal)

Time setting: approx. 10 sec-4 min

MAINTENANCE AND CLEANING

All maintenance work must be carried out by a qualified electrician.

PLEASE NOTE: The LED light does not contain parts that need servicing. The LED light source cannot be replaced. If necessary, replace the entire light.

Do not use solvents, corrosive cleaners or the like. Use a dry or slightly moist cloth for cleaning ONLY.

Operating Instructions Chip LED Light

Dispose of electrical devices in an environmentally responsible manner!

Do not dispose of electrical devices with household rubbish!

In accordance with Directive 2012/19/EU on waste electrical and electronic equipment, used electrical equipment must be collected separately and reused or recycled in an environmentally responsible manner.

Please contact your local authorities for available disposal options for your worn-out device.

Addresses

BESCHRIJVING VAN DE WERKING

LCN130PIRIP44 30W(1x30W) IP44Ja220,5x180,5x4mm

LCN150IP6550W(1x50W) IP65Nej281,5x231x4mm

LCN150PIRIP44 50W(1x50W) IP44Ja281,5x231x4mm

LCN180IP6580W(1x80W) IP65Nej303,5x225,5x5mm

YKA3AHNIO TEXHnke 6E3OpACHOCTN

1. YctaHOBka n 06cnyKuBaHne JAMnbI DOJKeH npOBoNTb KBaINΦnCnpOBaHHbI CneuaJIInCT.

2. Перед установкови Тхостмотром BCERda OTКлочаite Hanpopжени.

Chip CnД-лamma RyKOBoDCTBO NO 3KcPnyatauIN

RU

3.лamnyселуетзаemлгьпо поядку.
4. Данная Лампа He может 6ыТь ИСПОЛБ3ОВаHA 6e3 Cпeциальных npokладочных кoleц!
5. CnД-лamna CBeTNT OueHЯрko. Hn npu KaKnx 6OCToRteNbCTBax He cMOTpnte B IyU CBeTa OT CnД-лamnbI, TaK KaK 3TO MoXeT npINBeCTN K NOBpeJKeHIO rla3.
6. ClomahHoe 3aHTHOe NOKpbTne cIeDyET 3aMeHnTb Ha opuHaJIbHoe 3aHTHOe NOKpbTne ot Brennenstuhl nepei CLeDyUoIM IcNoJIb3OBaHNem JaMnbl.

1. Ecnn IHHN NOKJIUOeHn K CeTn IaMnbI NOBpeXKeHa, KBaIIuΦnIupoBaHHbI CneuaJIInCT DoJKeH 3aMeHHTb ee BO n36exKaHHe OnaCHOCTn.

MOHTAXI NOIDCOEINHEHNE K 3JEKTPOCHABXEHNIO

1. UcTaHOBnTe IaMny Ha IOBePxHocTb, KOtOpa He 6yJeT Bn6pnpoBaTb.
2. Положения по мontаж: Вideале Ламна дожна 6ытб зakpenлеса по помоши настеного кpenlenия. Лamny сдачимдвожени садует зakpenпь, кak уka3aHO на рис.1.
3. OtmetbTe noloxeHne npocBepnHbIX no3nui dIy 3aKpeJIeHnaCTeHHoro KpeJIeHnI N npocBepnIte COOTBeTCTByIOuIe OTBepCTnB CTeHe. 3aKpeIte Duyry npi NOMOUI NOxOJuxxBnHTOB K CTeHe.
4. OTKpoIte Kopo6ky dny noDcoeINHeHn r npoBOD naMnbl.

69

RU RykoBoDCTBO no 3KcPnyatauim Chip CnД-lanma

1. ПювадиTe coeHHTeHbI npOBOD uepe3 Ka6eHbI BBOI n IOdcoeHHTe erO, KaK yKa3aHO Ha pnc. 2 (KapTnHka cIeBa dIy BepCn 10 W, KapTHKa cnpabaДЯ BepCn 30 W n daJIbSe), K KJIeMMOBoi KOLOdKe IaMnbl (N = cnHni Ka6eJb, ycIOBHOe rpaΦnueckoe o6o3HaueHne 3a3eMHeHnry = 3eJIeHbI / JeNTbI Ka6eJb, L = KopuHBeBII Ka6eJb).
2. y6eIntecb, yTO Ka6eIb HAdEJHo 3aΦnKcnpOBaH npi nOMoUn Ka6eIbHOrO BBOda.
3. CoeHnTe nokpbItne c kopo6kOJ IJIa IODcoEINHeHnI npOBoOB.
   ObpaaTe BnMaHne Ha npaBnIbHoe noloxHne ynpOTHeHnI.
4. YcTaHOBnTe NaMny C COBMeCTHO NOCTaBHeHHbIMN 6oTAMn I raKamn Ha HacteHHoe KpeJIeHne. YcTaHOBnTe JKeJaemoe NpIoXeHne NaMnbl N 3aTAHnTe 6oTbI.

ONICAHNE PUNHUNPA PABOTbl

TEXHNUECKN OCMOTP N OUNCTKA

Texnueckn OCMOTp DOJKeH npOBODtB TOlbKO KBaINΦNUPOBaHHbI ΘJIeKTPNK.

PykoBoDCTBO NO 3KcnpyaTaumn Chip CnД-lanma

BHIMAHHE: CnД Лamпа He copejNT KOMNoHEnTbI, KOToPbIe HJxJaIOrTa B TexHnueCKOM OcMOTpe. CnД nCTOuHNK CBeTa He MoXeT 6bITb 3aMeHeH. B cIyuae Heo6xOДmOCTn, cIeDyET 3aMeHHTb BCIO JAMny.

He nCnoIb3yIte paCTBOpHTeI, eKne YnCTaIe CpeIcTba nn noXoJNc BeIecTBA. IJI OuNCTKn nCnoIb3yIte TOnbKO cyXyIO nn cIeRka BnaJxHyIO caIΦeTKy.

3JIeKTPnueckne np6Opbl noJleKaT yTNIn3aunC yUeTOM 3aunTbI OkpykaIoUeN cpebl! BbI6paCbIBaTb 3JIeKTPnueckne np6Opbl B 6bITOBble OTXoDbI 3anpeucaetc!

B COOTBETCTBnC DnpeKtNBOE NC No 2012/19/EU no OTPa6oTaHHbIM 3JIeKTPoPnp6Opam N 3JIeKTPoHNo annapatype OTPa6oTaHHbIe 3JIeKTPoPnp6Opbl DOJXHbI Co6npaTbcra B OTdJIbHbIe KOHTeINHepbI N OTpAbTbcra Ha IpeDnprnTne dJa BVTopuHOrO nCIOJb3OBaHnA OTXODOB C CO6JIouDeHnEm HOpM 3aunTbI OKpykaIoSei cpebl.

BO3MOxHOCCTaX yTnIIN3aunn npnbopa, Otpa6oTaBwero CBOI pecypc, MOxHO y3HaTb B MeCTHom IIN rOpOdCKOM camOynpabHeHH.

Ampes

LCN130IP65 30W(1x30W) IP65Ei220,5x180,5x4mm

LCN130PIRIP4430W(1x30W) IP44Jah220,5x180,5x4mm

LCN150IP65 50W(1x50W) IP65Ei281,5x231x4mm

LCN150PIRIP4450W(1x50W) IP44Jah281,5x231x4mm

LCN180IP65 80W(1x80W) IP65Ei303,5x225,5x5mm

LCN130PIRIP4430W(1x30W) IP44Ja 220,5x180,5x4mm

LCN150IP65 50W(1x50W) IP65Ne281,5x231x4mm

LCN150PIRIP4450W(1x50W) IP44Ja 281,5x231x4mm

LCN180IP65 80W(1x80W) IP65Ne303,5x225,5x5mm