Q Revo Pro - Robot vacuum ROBOROCK - Free user manual and instructions

USER MANUAL Q Revo Pro ROBOROCK

Robotic Vacuum Cleaner User Manual

Read this user manual with diagrams carefully before using this product and store it properly for future reference.

Battery and Charging International Symbols Explanation FCC/IC Statement

Connecting to the App Instructions for Use

Environmental Protection Description

Safety Information WARNING

+ For use only with roborock EWFD16LRR or EWFD20LRR charger.

+ The product must be switched off and the plug must be removed from socket outlet when not in use, before cleaning or maintaining the product.

+ Connect to a properly grounded outlet only. See Grounding Instructions,

+ Only use the product in accordance with the User Manual. Any loss or damage caused by improper use will be borne by the user.

+ Make sure dustbin, washable filter, dust bag, side brush, mop cloth, main brushes and main brush cover installed in place before cleaning

+ Do not sit or stand on the robot or dock.

+ To prevent corrosion or damage, do not use any disinfectant and only use cleaning solution recommended by Roborock in the solution cartridge

+ Do not put any low objects (such as shoes, mats) near raised areas like stairs. Otherwise, the robot may fall down caused by malfunctional sensors.

+ To prevent water damage, make sure that the floor where the robot operates is free of water.

+ Place the cords from other appliances out of the area to be cleaned

+ Do not operate the vacuum in a room where an infant or child is sleeping

+ Do not operate the vacuum in an area where there are lit candlles or fragile objects on the floor to be cleaned

+ Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into.

+ Do not allow children to sit on the vacuum.

+ Do not carry the robot using vertical bumper, top cover, side brush or bumper. Do not move the dock by lifting dock base, water tank handles or dust container cover.

+ Place the dock on a hard, fiat floor away from fire, heat, and water. Avoid narrow spaces or locations where the robot may be suspended in the air.

+ This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be made by children without supervision.

+ Do not dismantle, repair or modify the battery or charging dock + Ifthe dock is placed in an area susceptible to thunderstorms or with unstable voltage, take protection measures. + Do not rinse the robot and the dock

GROUNDING INSTRUCTIONS This appliance must be grounded. Ifit should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug

The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances

WARNING -improper connection ofthe equipment-grounding conductor can result in a risk of electric shock

Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not ft the outlet, have a proper outlet installed by a qualified electrician

This appliance is for use on a nominal 120-V circuit and has a grounding attachment plug that looks like the plug illustrated in sketch À in Grounding methods. Make sure that the appliance is connected to an outlet having the same configuration as the plug

No adaptor should be used with this appliance

Battery and Charging

+ Keep the charging dock away from heat (such as radiators)

+ Do not wipe the charging contacts with wet cloth or wet hands.

+ If placing the robot into storage, charge it fully and turn it off before placing it in a cool dry place. Recharge it at least every three months to avoid battery overdischarge

+ Do not use the product when the temperature is higher than 40°C (104°F) or lower than 4°C (39°F) or there is any liquid or sticky substance on the floor.

+ Do not discard waste batteries. Leave them with a professional recycling organization.

+ To transport the product, make sure it is powered off and shut down, and empty the remaining fluid in the water tanks. At the same time, empty and rinse the cleaning solution cartridge, leave it air dry completely and then reinstall it. Original packaging is advised

International Symbols Explanation

— - ALTERNATING CURRENT symbol [symbol IEC 60417-5032 (2009-02)] = - DIRECT CURRENT symbol [symbol IEC 60417-5031 (2009-02)] @ - PROTECTIVE EARTH (Protective Ground) symbol [symbol IEC 60417-5019 (2009-02)]

Robotic Vacuum Cleaner with Charging Dock

Robotic Vacuum Cleaner Model: QRIPES Empty Wash Fill Dock: EWFD16LRR Empty Wash Fill Dock Auto: EWFD20LRR Compliance Statement

This device complies with Part 15 ofthe FCC Rules.

Operation is subject to the following two conditions

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada licence-exempt RSS(s). Operation is subject to the following two conditions

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device

Correspondence of the responsible party in USA Company Roborock Technology Co. Address ROOM 1227, 12TH FLOOR, 1000 N. WEST STREET, WILMINGTON, DE 19801 Email support@roborock.com

@ Product Overview Robot (Top View)

(D —-Power/Clean + Press and hold to turn the robot on or off + Press to start cleaning

Power Indicator Light + White: Battery level = 15%

+ Red: Battery level < 15%

+ Breathing: Charging or starting up + Flashing red: Error

© —Dock + Press to return to dock/start empojing + Press and hold to start spot cleaning! mop washing

Note: Press any button to stop the robot during cleaning

Robot (Top Cover Open)

A3-1—Vertical Bumper A3-2—LiDAR Sensor A3-3—WiFi Indicator Light + Off WiFi disabled/Charging + Flashing slow. Waiting for connection + Flashing quickÿ: Connecting + Steady: WiFi connected A3-4—Reset Button A3-5—Dustbin A3-6—Charging Contacts A3-7—Communication Sensor A3-8—Air Outlet A3-9—Positioning Button A3-10—Self-Filling Port A3-11—Automatic Lift and Rotate Mop Modules A3-12—Suction Inlet A3-13—Bumper

A4-1—Hook and Loop Pads A4-2—Mop Axle

Note: Secure the mop claths in place.

Dock —Water Tank Handle Water Tank Latch

—Dirty Water Tank Dust Container Cover —Charging Contacts — Robot Refill Port —Suction Inlet — Clean Water Tank Status Indicator Light + Breathing: Emptying/Mop washing + Red: Dock error + Off Powered off/Charging A10-10—Water Outlet A10-11—Aïr Outlets A10-12—Dock Base A10-13—Filter A10-14—Dust Bag Slot A10-15—Dock Location Beacon A10-16—Clean Water Dispensers

A10-17—Water Level Float A10-18—Cleaning Tank Filter A10-19—Cleaning Tank

@ Power Cord Storage

@ Important Information

B1-1—Tidy cords, hard or sharp objects {such as nails and glass), and loose items from the ground and move any unstable, fragile, precious, ar dangerous items to prevent personal injury or property damage due to items becoming tangled in, struck by, or knocked over by the robot.

B1-2—When using the robot in a raised area, always use a secure physical barrier to prevent accidental falls that may result in personal injury or property damage

Note: Wen using the robot for the first time, fol

it throughout its hole cleaning route and watch for

potential problems, The robot il be able to clean by itselin future uses,

B2-1—Place the dock on a hard and flat floor.

Atrach the base by pressing down both sides ofthe base firmiy, and then pressing the connecting part in the middle until you hear a click.

Note: When moving the dock, secure the water tank to

prevent it from faling of.

82-3—Connect the power cord to the back ofthe dock, and keep the excess card inside the storage slot.

Note: Power cor can ext at either side.

82-4—Align and install the mop axes into the robot in place until you hear aclick’.

Keep a space of clearance about 0.9 m (2.9 D in height, 0.4 m (1.3 ft) in length and 1.2 m (3.9 #0 in width. Place the dock on a hard and flat floor (wood/tile/concrete etc.) flat against a wall. Make sure the location has good Wifi for a better experience with the mobile app, and then plug it in and make sure the dock status indicator light is on

B3-1—About 0.9 m (2.9 ft) B3-2—About 0.4 m (1.3 ft) B3-3—About 1.2 m (3.9 ft)

+ Ifthe power cord hangs vertical to the ground, it may be caught by the robot, causing the dock to be moved or disconnected.

+ The dock status indicator light s on when the dock is pomered on, and off when the robot is charging

+ The dock status indicator light turn red if an error oceurs.

+ Place the dock on à lat floor away from fire, heat, and water. Avoid narrow spaces or locations where the robot may be suspended in the air

+ Placing the dock on a sof surface (carpet/mat) may. cause the dock to tit over and cause problems docking and departing,

+ Keep the dock away from direct sunlight or anything that may block the dack location beacon: othermise; the robot may fall to return to the deck

+ Do notuse the dack without clean water tank dirty water tank, dust container cover, disposable dust bag, er cleaning tank.

+ Maitainthe dock accordingtothe maintenance instructions. Do not clean the dack with a et cloth or tissue.

+ Al docks are subject to water-based tests before leaving the factory. I is normal that a small amount of water remains in {he waterway of the dock

© Powering On & Charging

Press and hold the () button to pawer on the robot. Wait until the power light is steadh, and then place the robot on the dock to charge Make sure the dockis powered on. Press the O button on the robot to make the robot automatically return to the dock for charging. The robot is equipped with a butin high- performance lithium-ion rechargeable battery pack. To maintain battery performance, keep the robot charged. 84-1—Dock Status Indicator Light turns off, Robot Power Indicator Light breathing: Charging

Note: The robot may not be turned an when the battery Is low. In this case, place the rabat to the dock for charging

Connecting to the App 1. Download App

Search for “Roborock" in the App Store or Google Play or scan the QR code to download and install the app.

2. Open the top cover and find the WiFi indicator light.

b. Press and hold the (and © buttons until you hear the “Resetting WiFi” voice message. The reset is complete when the WiFi indicator light flashes slowly. The robot will then wait for a connection.

Note: I you cannot connect to the robot due to your router configuration, a forgotten password, or any other reason, reset the WiFi and add your robot as à new device.

Open the Roborock App, tap the ‘Scan to Connect ar “Search for Device’ button and add the device as instructed in the app

+ The actual process may vary due to angoing app updates. Follow the instructions provided in the app.

+ Only 2.4 GHz Wii is supported.

+ IFthe robot waîts more than 30 minutes for a connection, WiFi will be automaticaly disabled. 1 you want to reconnect reset the \WFi before proceeding,

Q instructions for Use On/off

Press and hold the () button to turn on the robot. The power indicator light will turn on and the robot will enter standby mode Press and hold the () button to turn off the robot and complete the cleaning cycle.

Note: The rabot cannot be turned offwhenit is being charged

Filling the Water Tank

Remove and open the clean water tank and filLthe tank with water to MAX. Close the lid, lockthe latch, and fitthe tank back in place: Notes:

+ To prevent corosion er damage, do notuse any disnfectant and oniyuse deaning sokion recommended Ey Roborcck inthe water tank.

+ De not add too much cleaning solution ta prevent the robot from vorking imprperl due ta sipping

+ To avoid water tank deformation, do not place hot water inthe tank

+ lfwater marks remain on the water tank, wipe them clean before reinstalltion.

Press the () button to start cleaning. The

robot wil plan its cleaning route according to its scan ofthe room. It splits a room into zones, first draws out zone edges, and then fils the zone in a zigzag pattern. In 50 doing, the robot cleans all zones one by one, efficientiy cleaning the house.

C2-1—Zone 1 - Cleaned' C2-2—Zone 2 - Cleaned' C2-3—Zone 3 - In Progress. C2-4—Zone 4 - Next Zone.

+ To allawthe robot to automatically vacuum and return tothe dack start the robot fram the dock. Da not mave the dock during cleaning.

+ Cleaning cannot start ifthe battery level is too lan. Allow the robot ta charge before starting the cleanup.

+ Before cleaning, tidy cord (including the power cord ofthe dock) and valuables from the floor. Loose items may be dragged by the robot, resulting in the disconnection of electrical appliances or damage of cords and property.

If dleaning is completed in less than 10 minutes, the area will be ceaned twice.

+ fthe battery runs low during the cleaning cycle, the robot: wi automaticaly return to the dock. After charging, the robot will resume where it left off.

+ The robot wil retract mop cloth mounts when cleaning the carpet. You can alsa set the carpet as a no-g0 zone in the app to avoid it

+ Before starting each cleaning task, make sure that the mop cloths have been proper) installed

Press and hold the O button to start spot cleaning in pause mode

Cleaning range: The robot deans à 1.5 m (4.9 ft)x 1.5 m (4.9 ft) square area centered on itself.

Note: After spot cleaning, the robot will automatically return to the starting point and be on standby.

When the robot is running, press any button to pause it, press the () button to resume cleaning, and press the © button to send it back ta the dock

Note: Placing a paused robot on the dock manually will end the current cleanup.

Ifthe robot is paused for over 10 minutes, ituill go to sleep, and the power indicator light will flash every few seconds. Press any button to wake the robot up.

+ The robot wil not go ta sleep when it is charging

+ The robot will automaticaly shut dovin ile in sleap mode for more than 12 haurs.

The default Do Not Disturb (DND) period is from 22:00 to 08:00. You can use the app to disable the DND mode or modify the DND period. When DND is on, the robot will not automatically resume cleanup, the power indicator light will dim, and the volume of the voice message will lower.

Washing the Mop Cloths

During cleaning, the robot automatically determines when it should return to

the dock for mop washing and water

tank refilling to maximize its mopping

performance. During cleaning, tap Dock button in the app to send robot back for mop washing. When the robot is charging, press and hold the O button on the robot or tap Wash button in the app to manually start washing. Press any button to stop washing

To low the robot to wash the mop automaricalh, start the robot from the dock and da not moe the dock during cleaning

«Watch out fr hot ter and do nat touch the water out

+ Mopwash frequency and ashing mode an be modified in the app.

Auto-emptying will automatically begin when

the robot returns to the dock after cleaning

To manually emptying, press © button on the

docked robot or tap the corresponding button

in the app. Press any button to stop emptying,

+ When auto-emphying has been left unused for a long period, empty the dustbin manual and make sure the airinlet is cear for aptimal emptying performance.

+ Auto-emptying can be disabled through the app. + Avoid frequent manual emptying,

Drying starts automatically after mop washing or after cleaning is completed. To manually start or stopping drying, tap the corresponding button in the app.

Notes: + Drying duration can be modified in the app. + Auto-drying can be disabled through the app.

After cleaning, the robot will automatically return to the dock to charge. In Pause mode, press the O button to send the robot back to the dock The power indicator light will breath as the robot charges.

automatically return toits starting location. Place the robot on the dock manually ta recharge.

Ifan error oceurs, the power indicator light on the robot will flash red or status indicator light an the dock will be steady red. À pop- up notification will receive in the app and a voice alert may sound.

+ The robot will go te sleep automatically Flef in a mafunctioning state for aver 10 minutes.

+ Placing a malfunctioning robot on the deck manually wilend the current cleanup.

Resetting the System

Ifthe robot does not respond when a button is pressed or cannot be turned off, reset the system. Press the Reset button, and the robot will reset automatically.

Note: After resetting the system, existing settings such

28 scheduled cleaning and WiR vil be restored to factory settings.

Restoring Factory Settings

Ifthe robot does not function property after à system reset, switch it on. Press and hold the O button and at the same time, press the Reset button until you hear the "Restoring factory settings” voice message. The robot will then be restored to factory settings.

@ Routine Maintenance

Note: The frequency of replacement may vary depending on the situation. anormal wear aceurs, replace the parts immediately.

+ Clean every 2 weeks and replace every 6-12 months.

D1-4—Main Brush Caps

D1-5—Main Brush Bearing

D1-6—Turn over the robot and press the main brush latches to remove the main brush cover.

D1-7—Pull out the main brush and remove the main brush bearing. Rotate the main brush caps in the indicated unlock direction to remove the caps, and remove any entangled hair or dirt at both ends of the main brush

D1-8—Reinstall the main brush

D1-9—Reinstall the main brush cover. Make sure that the four teeth are fully seated in the slot, and then press on the main brush cover to lock it until you hear a click.

+ Main brush shouid be wiped doun it ave cloth. the main brush is et, air-dryit away from direct sunlight.

+ Do not use corrosive cleaning fuids or disinfectants to dlean the main brush

+ Clean monthly and replace every 3-6 months. Unscrew the side brush screw. Remove and clean the side brush. Reinstall the brush and tighten the screw.

Omnidirectional Wheel

+ Clean as required.

D3-1—Use a tool, such as a small screwdriver, to pryoutthe axe and take outthe wheel.

Note: The omnidrectionalheel bracket cannot be removed

D3-2—Rinse the wheel and the axle with water to remove any hair and dirt. Dry and reattach the wheel, pressing it firmy in place.

Clean the main wheel with a soft, dry cloth.

D5-1—Open the top cover ofthe robot and press the dustbin latch to take out the dustbin

D5-2—Open the washable filter and empty the dustbin

D5-3—Fil| the dustbin with clean water and reinstall the washable fier. Gentiy Shake the dustbin, and then pour out the dirty water.

Note: To prevent blockage, only use clean water without any cleaning liquid.

DS-4—Leave the dustbin and the washable fier to dry.

+ Clean every Zweaks and replace the ter every 6:12 monts.

D6-1—Remove the filter.

D6-2—Rinse the filter repeatedly and tap it to remove as much dirt as possible

Note: Da not tauch the surface of the filter with yaur handé, brush, or hard objects to avoid potential damage:

D6-3—Allow at least 24 hours for the filter to dry thoroughly and reinstall it.

+ iean as required and replace every 1.3 months.

D7-1—Remove the mop cloth from the mop cloth mount. Clean the map cloth and air-dryit

Note: A dry mop dothwil affect the washing performance.

D7-2—Stick the mop cloth on the mount in position and firmiy.

Use a soft, dry cloth to wipe and clean all sensors, including

Lift up and move the dock. Do not move the dock by lifing the dock base, water tank handles or dust container cover directly to prevent the dock from falling of.

+ Clean as required.

Open the dirty water tank lid and pour out the dirty water. Fill the tank with clean water, close the lid, and shake. Pour out the dirty water. Close the lid and then re-install

Charging Contact Areas

Use a soft dry clath to wipe the charging contacts on the robot and the dock.

Replacing Disposable Dust Bag

+ Replace as require

D12-1—Remove the dust container cover.

D12-2—Remove the disposable dust bag in the

direction of the arrow and discard it.

+ The dust bag hand seals the bag en remaval te prevent leakage.

+ Ars instal a dust bag before csing the dust cantainer cover ta avoid auto-emptying without the bag. You can ako disable auto-empting in the app.

D12-3—Clean around the filter with a dry

cloth. Install a new disposable dust bag in place along the slot and unfold the dust bag to maximize emptying performance.

Note: Make sure the disposable dust bag is proper sealed to avoid waste escaping and damaging the dock.

D12-4—Close the dust container cover and make sure it is securely sealedi

+ Clean as required D13-1—Remove the cleaning tank.

D13-2—Rinse the cleaning tank and the filter with water.

D13-3—Reinstall the cleaning tank.

Model QRIPES Bat 14.4 V/5200 mAh (TYP) artery lithium-ion battery

Rated Input 20V= 1.5A Charging Time Approx 4 hours

Note: Th ofthe robot.

ial number is on a sticker on the underside

Empty Wash Fill Dock

Model EWFDI6LRR Rated Input Voltage 120V- Rated Frequency 60Hz

Rated Input (Hot water washing 12A

mop) Rated Input n (Charging & drying) Rated Output 20V= 1.5A 14,4 V/5200 mAh (TP)

Charging Battery Kihiumion battery

Environmental Protection Description

Removing the battery

+ The folloning information apples only when disposin le br and hou not Le lolo or day Lo 2 perations

The chemical substances contained in the builtin lithium-ion battery of this product can cause environmental pollution. Before disposing of this product, remove the battery. The battery should then be properly recycled either through local authorities

or by providing the batteries to a battery recycling facility.

Hour to remove the battery:

1. Operate the robot without connecting to the dock until it runs out of battery.

2. Turn off the robot.

3. Unscrew the battery cover.

4. Remove the battery cover.

5. Press the latch to pull out the battery connector and remove the battery.

+ Before removing the battery, make sure its full drained and the robot is disconnected from the dock.

+ Remove the entire battery pack Avoid damaging the battery pack casing to avoid short-circuits or leakage of hazardous substances.

In the event of accidental contact with battery fluid, rinse tharoughly with water and seek immediate medical care.

Issue Solution Issue Solution

+ Battery low Put the robot on the charging dock and charge + WiFi disabled. Reset the WiFi and try again. Unable to it before use. + Poor WiFi signal. Move the robot to an area with good power on. + Battery temperature too low or too high. Only use the Unable to WiFi reception.

robot within the range of 4-40°C (32-104%F) connect to *’Abnormal WiFi connection. Reset the WiFi donnload Ve the latest mobile app and retry:

+ Dock not connected to pwer. Check whether both HF + Unable to connect to WiFi abrupth. There may be an Unable ta ends of the power cord are properly connected error with your router settings. Contact Roborack Customer Une + Poor contact. Clean the charging contacts of the dock Service far help with troubleshooting.

and the robot. + Confirm that the dock indicatar ligh is on.

+ When used at high or low temperatures, the robot will automatically reduce its charging speed to extend battery life:

+ Charging contacts dirty. Wipe them with a dry cloth.

+ Too many obstacles near the dock Move to an open area.

+ The robots too far from the charging dock. Place it closer and retry

+ The docklocator may be dirty. Wipe them with à dry coth.

Noise during cleaning.

+ The main brush, side brush, or main wheels may be jammed. Turn offthe robot and clean them.

+ The omnidirectional wheel is jammed. Use a screwdriver to remove it for cleaning.

Is power always being draun when the

robot is on the charging dock?

+ The robot will draw power while it is docked to maintain battery performance, but the poer consumption is extremely low.

Does the rabot need to be charged far at least 16 hours far the first three uses?

+ No. Lithiumion batteries have no memory effect The robot can be used once fully charged.

Cleaning does not resume after recharging.

+ Make sure that the robot is not in DND mode. DND mode will prevent cleanup.

+ The robot will not resume cleaning if users press button to recharge or manuall place the robot back to the dock.

Issue Solution Issue Solution The robot + The wall sensor, cliff sensors, or carpet sensor may be 1 Auro-empyin fs disabled Checkin-app settings suddenly misses + Dock dust container cover is not installed. Check and instal. dirty. Wipe them with a soft dry cloth à certain spot. Unabe + Auto-emprying will not be triggered if the robot returns ta the dock without cleaning] Schedules are auto-empty.

+ Schedules wil only take effect when the battery is higher than 15%.

The LED status indicator light on the dockis

+ Voltage error. Check that the local voltage meets the requirements listed on the dock.

+ Check clean water tank placement or refil as required

+ Check dirty water tank placement or empty as required.

+ The robot will not auto emptying after returning to the dockin the Do Not Disturb (DND) mode. Adijust cleaning or DND duration, or start emptying manual

Unable to wash the mop cloths.

+ The mop will not be washed if not used

+ 1fthe robot does not start from the dock or no dockis found on the app map, it vil not return to the dock for mop washing.

+ Check clean water tank placement or refill as required

+ Check dirty water tank placement or empty as required

+ Check that the cleaning tank or cleaning tank fier has been correctly installed.

Unable to wash the mop cloths th hot water.

+ Check that Map Washing with Hot Water is enabled in the app.

steady red + Check that the cleaning tank or cleaning tank fier has been correctly installed.

emptying + The main brush or main brush cover is not properly

performance installed. Check and install in place

or unusual + The filter, air duct, suction inlet, air nlet, dustbin or dust

noise when bag is blocked. Clean to remove blockages.

Reduced + The mop cloths are not attached properiy. Reinstall.

mop washing + The floar is dirty. Change the mop washing mode in the

performance. app for better cleaning,

Unable ta start auto-drying.

+ Auto-drying is disabled. Check in-app settings. + Auto-drying starts only after mopping ar mop washing.

Unable to extend the mop cloth.

+ Check whether the FlexiArm Extend Cleaning feature is enabled in the app.

+ The mop cloth will only extend along walls and certain obstacles.

+ Please check ifthe mop extension structure is stuck.

Roborock Q Revo Pro Manuel d'utilisation de l'aspirateur robot

— - ALTERNATING CURRENT symbol [symbol IEC 60417-5032 (2009-02)] = DIRECT CURRENT symbol [symbol IEC 60417-5031 (2009-02)] @ - PROTECTIVE EARTH (Protective Ground) symbol [symbol IEC 60417-5019 (2009-02)]

© Placement de la station

Roborock Technology Co.

ROOM 1227, 12TH FLOOR, 1000 N. WEST STREET, WILMINGTON, DE 19801

support@roborock.com

ee el siguiente cédigo QR para ver as comunes.

Robotic Vacuum Cleaner

Product Model QRIPES Manufacturer:Beling Roborock Technology Co, Ltd Address of Manufacturer: Room 1001, Floor 10, Building 3, Yard 17, Anju Road, Changping District, Bejing, PR. China

For more product information, vis our website: www robarock com For aftr-sales suppor, contact our support team at: Supporc@robarack com (United States/Canada/Nan-Europe) 1-855-960.4321 (United States only)

1:832.421-1915 (Canada on)