KSG 239 - Kitchen appliance BOMANN - Free user manual and instructions

USER MANUAL KSG 239 BOMANN

• The appliance is designed exclusively for com- Introduction mercial use and for the envisaged purpose. This Thank you for choosing our product. We hope you appliance is not fit for private use. will enjoy using the appliance.

• The appliance is only to be used as described in the user manual. Do not use the appliance for any Symbols in the these Instructions for Use other purpose. Any other use is not intended and Important information for your safety is specially can result in damages or personal injuries. marked. It is essential to comply with these instruc-

• Do not use it outdoors. Keep it away from sources tions to avoid accidents and prevent damage. of heat, direct sunlight and humidity. WARNING

• When not in use, for cleaning, user maintenance This warns you of dangers to your health and indi- works or with disruption, switch off the appliance cates possible injury risks. and disconnect the plug (pull the plug itself, not the lead) or turn off the fuse. CAUTION: CAUTION:

• The appliance and if possible the mains lead have This refers to possible hazards to the machine or to be checked regularly for signs of damage. If other objects. damage is found the appliance must not be used. NOTE: NOTE: This highlights tips and information.

• For safety reasons, alterations or modifications of the appliance are prohibited. General Notes

• In order to ensure your children’s safety, please Read the operating instructions carefully before put- keep all packaging (plastic bags, boxes, polysty- ting the appliance into operation and keep the in- rene etc.) out of their reach. structions including the warranty and the receipt. If WARNING

NING: you give this appliance to other people, please also Do not allow small children to play with the foil. pass on the operating instructions. There is a danger of suffocation! NOTE: NOTE: The illustrations in this instruction manual can deviate from the original appliance. Special safety Information for this Unit

• This appliance is intended for commercial use only.
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

• Do not use mechanical devices or other means to accelerate the defrosting process (if necessary), except those described in this manual (depending on the model included the scope of delivery).
• Do not damage the refrigerant circuit.
• Do not operate any electrical devices inside the appliance.
• Do not store explosive substances such as aerosol containers with flammable propellant in the appliance.
• Do not try to repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have faulty cable be replaced only by the manufacturer, by our customer service or by qualified person and with a cable of the same type.
• Use the provided collection points of electrical equipment for the disposal of the appliance. Coolant Transport and Unpacking the Appliance WARNING

NING: Transport the appliance The coolant circuit of this appliance contains the Transport the appliance, if possible, only in vertical refrigerant Isobutane (R600a), a natural gas that is position. Otherwise, it is absolutely necessary to flammable and of high environmental compatibility. allow the appliance standing upright for a few hours Make sure no parts of the coolant circuit get dam- before installation ”Prior to first use”. Protect the ap- aged during transport and installation of the appli- pliance during transport against weather influences. ance. NOTE: NOTE: If the coolant circuit is damaged: The appliance has wheels which facilitate the

• avoid any open flames or ignition source, transport and installation of the appliance. Tilt the

• disconnect the plug, appliance back slightly and move it gently.

• thoroughly air the room in which the appliance is Unpacking Unpacking the appliance installed and
• contact an authorized technician.

• Remove the appliance from its packaging.
• Remove all packaging material, such as foils, filler and cardboard packaging.
• To prevent hazards, check the appliance for any transport damage.

• In case of damage, do not put the appliance into

operation. Contact your distributor. Gap to the back and to the side walls each approx. 10 cm by using the spacers;

CAUTION: Transport protection! Place the appliance so that the appliance door can open without being impeded. Remove the Styrofoam part between appliance back

• Only install at a location with an ambient tempera- and condenser (metal grille). ture suitable for the climate class of the appliance. NOTE: NOTE: For information on the climate class, please refer Production residue or dust may have collected on the to the “Product Data Sheet” or to the rating label appliance. We recommend cleaning the appliance located in the interior or on the appliance rear. according to chapter “Cleaning and Maintenance”.

• Place the appliance on a steady and safe surface. If the appliance is not horizontally leveled, adjust Appliance Equipment the feet accordingly.
• Avoid the installation: Appliance overview

1 On/Off switch near heaters, next to a stove, direct sunlight or any other heat sources; interior light

2 Temperature at locations with high humidity (e.g. outdoors, bathroom), as metal parts would be suscepti- control ble to corrosion under such circumstances; 3 Control indication

thermostat position near volatile or flammable materials (e.g. gas, fuel, alcohol, paint, etc.), in rooms which may 4 Control lamp have poor air circulation (e.g. garages). power supply 5 Interior light

6 Circulation fan Do not expose the appliance any weather. Fitting the spacers 7 Grid shelves 8 Door lock Insert the supplied spacers (1) 9 Condenser into the holder (2) on the back of 10 Water collecting the unit. tray 11 Compressor Electrical connection

• The installation to the mains supply must conform 5x Grid shelf, 2x key for door lock, 2x spacers to the local standards and regulations.
• Improper connection may cause to an electric Installation shock! shock
• Do not modify the appliance plug. If the plug does Conditions Conditions for the installation location not fit properly to the outlet, let install a proper

• Good ventilation is required around the appliance, outlet by an authorized specialist. in order to dissipate the heat properly and to guarantee efficient cooling operation at low power consumption. Sufficient clearance is necessary.

Setting 0 Setting 1 Setting 5 Off state Lowest setting Highest setting sured to disconnect the appliance from the power (warmest inside (coldest inside supply in case of emergency. temperature) temperature)

• The accessibility of the power plug must be en-

Make sure that the voltage supply matches the Note that the temperature will change depending on specifications on the rating label before the ambient temperature, frequency of door opening connecting. and the amount of food in the appliance.

• Connect the mains cable to a properly installed During initial operation, turn the temperature control and earthed wall outlet. to the highest setting first, until the appliance has

• If the plug after installation is not accessible, a reached the desired operating temperature. After- corresponding disconnect device must be availa- wards it is recommended to turn the control back to a ble to meet the relevant safety regulations. medium setting; correcting the temperature at a later point would then be easier. Startup / Operation Interior light Prior to first use The indoor light is switched on or off via the on/off CAUTION: CAUTION: switch. After transport, the appliance should be left standing Storing upright for about four hours before connecting to the power supply. Nonobservance could lead to malfunc- The appliance is exclusively suitable for cooling and tion of the cooling system and causes an appliance storing drinks. breakdown. Several storage levels for inserting the grid shelves, Clean the appliance interior including all accessory allows individual storage. Note the maximum loading parts. Consider the instructions which we provide in of each shelf is 50 kg. the chapter “Cleaning and Maintenance”. Capacity / loading: 322 Cans à 330 ml (70 x 120 mm) Starting the appliance 154 Bottles à 500 ml (70 x 170 mm)

• Connect the appliance to the power supply. The Store large bottles horizontally, with the opening control lamp lights up. facing forward on the grid shelves.

• Operate the temperature control. See also the section "Settings". Door lock The appliance has a child safety lock by the lockable Settings door. If necessary, lock the door and keep the keys Setting [ 0 ] means that the appliance is in the off in a safe place, which is inaccessible to children. state. Turn the temperature control clockwise, starting from this setting; the appliance will turn on automatically. The power levels [ 1–5 ] regulate the different values of the internal temperature.

Operating noise Cleaning and Maintenance Type of sound Cause Mumbling Compressor during its operation Liquid sounds Circulation of the refrigerant Click sounds The temperature control turns the

• Always disconnect the appliance from the power supply before cleaning and user maintenance.
• Do not use steam cleaners for cleaning the appli- compressor on or off Disturbing Vibration of the shelves or cooling noises coils ance; moisture could enter electrical components. Risk of electric shock! Hot steam could damage the plastic parts.
• The appliance must be dry before restarting oper- Switching off ation. To switch off the appliance appliance turn turn the temperature concon- CAUTION: trol to the off state.

• Do not use a wire brush or other sharp, abrasive If the appliance is out of use for long periods: items.

• Remove the appliance content.

• Do not use any acidic or abrasive detergents.

• Disconnect the appliance from the power supply.

• Do not damage the refrigerant circuit. The control lamp disappears.
• Clean the appliance thoroughly (see ”Cleaning Cleaning the appliance including interior and Maintenance”).

• Clean the appliance interior, the exterior surfaces,

• Leave open the appliance door to prevent un- the accessories and the door seal regularly with pleasant odours. warm water and mild detergent.
• Remove the appliance content and storage it at a Tips for Energy saving cool location.

• Disconnect the appliance from the power supply,

• Clean the thaw water discharge channel / opening if it isn’t in use. carefully e.g. with a pipe cleaner.

• Do not install the appliance near stoves, heaters

• After everything was thoroughly dried, you can or other heat sources. In case of higher ambient restart the operation. temperatures, the compressor will run more fre-

• Wipe at least once a year the dust that has accu- quently and longer. mulated on the appliance back and condenser

• Ensure sufficient ventilation at the bottom and (metal grille). To do this, use a soft brush or a rear side. Never block ventilation openings. vacuum cleaner.

• Do not adjust the temperature colder than necessary. Defrosting Defrosting

• Do not leave open the door for longer than re- The appliance has an automatic defrosting system. quired. During defrosting water drops drains off at the back

• The appliance should be defrosted regularly (if of the cooling chamber. The thaw water running necessary). through a channel, is collected in a drip tray located

• Switch on the indoor light only if necessary. on the compressor, where it will evaporate. Make

• The seal of the appliance door must be complete- sure the water discharge opening does not get ly intact, so that the door closes properly.

clogged. A light formation of ice on the interior back Technical Data during operation is normal. Electrical connec connection………………...………………….. Power voltage: ………………......….220-240 V~ / 50 Hz Changing the bulb Connection power: ……………………….…..….…230 W CAUTION: Power fuse: ……………………………………………1.7 A Do NOT remove the cover of the LED light. Dimension H x W x D / Weight…..…...……………….. The LED light may be replaced / repaired in case of Appliance size: ……..….…....…..173.0 x 60.0 x 60.0 cm failure / defect only by an authorized specialist. Net weight: …………………………..……approx. 65.0 kg The right to make technical and design modifications Troubleshooting in the course of continuous product development remains reserved. Before you contact an authorized specialist Problem Cause / Action This appliance has been tested according to all rele- Appliance is - Check the power supply / temperature vant current CE guidelines, such as electromagnetic not working properly or at all Loading is too warm setting / ambient temperature. compatibility and low voltage directives, and has - Unblock the ventilation openings, install been constructed in accordance with the latest safety the appliance freely. regulations. - Check the temperature setting / ambient temperature. - Open the door only as long as necessary. Loud noise - Check the appliance position. during oper- - See the section “Operating noise”. Disposal ation Meaning of the “Dustbin” Symbol Water on the Check the temperature setting / water appliance discharge channel or opening. Protect our environment; do not dispose of electrical Light does - Check the power supply. not work - See “Changing the bulb”. Please return any electrical equipment that you will equipment in the domestic waste. bottom no longer use to the collection points provided for NOTE: their disposal. If a problem still persists after following the steps This helps avoid the potential effects of incorrect above, contact your trader or an authorized techni- disposal on the environment and human health. cian. This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment. Information concerning where these can be disposed of can be obtained from your local authority.

Remove or disable any existing snap and bolt locks, if you take the unit out of operation or dispose it.

• Climate class according ISO 23953-2 Climate class Temperature Temperature °C Relative humidity (%)