EQ.6 PLUS S300 TE653501DE - Machine à café automatique SIEMENS - Free user manual and instructions

USER MANUAL EQ.6 PLUS S300 TE653501DE SIEMENS

Fully automatic coffee machine TE65..

Register your product on My Siemens and discover exclusive services and offers. siemens-home.bsh-group.com/welcome The future moving in.

 en Dear Coffee Connoisseur, Congratulations on purchasing this fully automatic coffee machine from Siemens. This instruction manual describes a number of versions of the appliance with minor differences. Please also take note of the enclosed Quick reference guide, which you can then keep in the specially provided compartment 16 until you need it again. How to use these instructions: You can open up the front cover of this instruction manual to see illustrations of the appliance with each part numbered. These numbers will be referred to throughout the text. Example: brewing unit 14 These instructions also show display texts and symbols in a special way so that you can clearly see where we refer to texts displayed by the appliance or symbols that are marked on it. Example of display texts: Espresso

W Warning Risk of electric shock! This appliance is intended for domestic use only. ■ The appliance may only be connected to a power supply Only use the appliance indoors with alternating current via at room temperature and up to a correctly installed socket 2000 m above sea level. with earthing. Ensure that the protective conductor system Important safety information of the domestic supply has Please read and follow the been correctly installed. operating instructions carefully ■ Connect and operate the and keep them for later referappliance only in accordance ence! Enclose these instructions with the specifications on the when you give this appliance to rating plate. someone else. ■ Do not use the appliance if This appliance can be used the power cord and/or appliby children aged from 8 years ance are damaged. and above and by persons with ■ Only our customer service reduced physical, sensory or may repair the appliance, mental capabilities or lack of e.g. by replacing a damaged experience and knowledge if power cord, in order to avoid they have been given supervihazards. sion or instruction concerning ■ Never immerse the appliance use of the appliance in a safe or mains cord in water. way and if they understand the ■ If there is a fault, pull out the hazards involved. Keep children mains plug immediately or under 8 years of age away from switch off the power supply. the appliance and connecting ■ Avoid spillage on the cable and do not allow them connector. to use the appliance. Children ■ Please note the special shall not play with the appliance. information on cleaning in the Cleaning and user maintenance instructions. shall not be made by children unless they are older than 8 years and supervised.

W Warning Hazard due to magnetism! The appliance contains permanent magnets which can affect electronic implants such as pacemakers or insulin pumps. Persons wearing electronic implants must maintain a minimum distance of 10 cm from the appliance and from the following parts upon removal: milk container, milk system, water tank, drip tray and brewing unit.

Important safety information

W Warning Risk of burns! ■ The milk system becomes extremely hot. After use, always let it cool down before you touch it. ■ After use the surfaces of the heating element or hotplate can remain hot for some time. ■ Freshly prepared beverages are very hot. Leave to cool a little if necessary.

W Warning Risk of suffocation! ■ Do not allow children to play with packaging material. ■ Store small parts safely as they can be easily swallowed. W Warning Risk of injury! ■ Do not reach into the grinding unit! ■ Improper use of this appliance may result in injury. W Warning Risk of fire! ■ The appliance gets hot. ■ Never operate the appliance in a cupboard.

Included in delivery

Included in delivery

(Figure A on the fold-out pages) a b c d e

Fully automatic coffee machine User Manual Quick reference guide Milk tube and suction pipe Water hardness testing strip

Measuring spoon Water filter * Milk container with “freshLock” lid * Descaling tablets *

(Figures B, C, D, E, F and G on the fold-out pages) 1 2 3 4

Mains switch J Control panel (see next page) Display Drinks outlet (coffee, milk, hot water), height-adjustable a) Cover b) Milk system /coffee outlet (two-part) c) Milk tube d) Suction pipe e) Milk system holder Removable water tank Lid for water tank Storage compartment for measuring spoon Measuring spoon (insertion aid for water filter) Bean container

10 Aroma cover 11 Dial selector for grinding level 12 Drawer (for ground coffee/cleaning tablet) 13 Door to brewing unit 14 Brewing unit a) Locking mechanism b) Cover 15 Eject lever 16 Storage compartment for quick reference guide 17 Drip tray a) Drip tray panel b) Drip tray (two-section) c) Coffee grounds container d) Floater 18 Compartment for power cord 19 Rating plate (E number, FD) * These user instructions describe a number of appliance versions. Items marked * are not present in all models.

Overview of control elements

Overview of control elements (Figure B on the fold-out pages)

FF The following symbols are visible or backlit depending on the appliance’s current operating mode:

Special beverages (see the section “Special beverages”).

G – Dispense two cups simultaneously

H – Set coffee strength

R – Call up Favourite (touch briefly) and Childproof lock (touch for at least 3 seconds).

Mains switch J The mains switch J is used to switch the appliance on or off. The appliance rinses itself automatically when it is switched on and off. The appliance does not rinse if: ■■ it is still warm when switched on, or ■■ no coffee was dispensed before it was switched off. The appliance is ready for use when the symbols and the display on the control panel are lit. Control panel (touch field) In the control panel you can easily navigate the controls just by touching the symbols and characters. You will hear an audible signal. These audible signals can be switched on or off (see the section “Menu – Key tones”). Drink selection Touching the corresponding symbol selects the desired drink (see the section “Preparing drinks”). Start/stop button Touching C either begins preparing a drink or launches a service programme. If you touch C again while the drink is being prepared, dispensing will be prematurely halted. Menu Touching A calls up the menu, the navigation symbols will be activated and light up. Touch I, B and F to navigate through the menu and call up information or change settings (see the section “Menu”).

Drink options Touching H or D adjusts the strength or size of the drink, touching G prepares two cups simultaneously as soon as you touch C to begin dispensing (see the section “Preparing drinks”). “Favourite” and Childproof lock Briefly touching R calls up personalised beverages (see the section “Own settings Favourite”). Touching R for 3 seconds or more ­activates or deactivates the childproof lock (see the section “Childproof lock”).

The display shows the selected drinks and settings plus messages reporting the ­appliance’s operating status.

Please refill water tank

These messages are cleared as soon as the action has been carried out.

General Fill the appropriate container using only pure, cold, uncarbonated water and solely roasted beans. Do not use coffee beans that have been glazed, caramelised or treated with other additives containing sugar, since they will block the brewing unit. The water hardness setting on the ­appliance can be adjusted. The factory setting for the water hardness is 4. Use the enclosed test strip to determine the hardness of your water supply. If this shows a value other than 4, you will need to programme the appliance appropriately after it has been taken into service (see section “Menu – Water hardness”). Setting up the appliance ■■ Remove any protective plastic film. ■■ Place the fully automatic coffee machine on a level, waterproof surface that is able to support its weight. ■■ The appliance’s ventilation slits must not be covered or obscured.

FF Important: Only use the appliance in a frost-free room. If it has been transported or stored at temperatures below 0°C, wait at least 3 hours before taking it into operation.

■■ Connect the power supply (cable storage compartment 18) to the socket. You can adjust the length of the cable by pulling it further out or pushing it back in. To do this, place the appliance with its back flush with the edge of the work surface and either pull the cable out downwards or push it in upwards. ■■ Flip up the lid of the water tank 6. ■■ Remove the water tank 5, rinse it out and fill it with fresh cold water. Do not fill it past the “max” mark. ■■ Replace the water tank 5, making sure that it is straight, and push it right down into place. ■■ Reclose the lid of the water tank 6. ■■ Fill the bean container 9 with coffee beans.

■■ Use the main switch J 1 to switch on the appliance. The control panel and the display will be activated. The display will show the previously specified language, which will also be used for all subsequent display texts. A number of different languages are available. ■■ Touch I repeatedly until the display indicates the desired language. Deutsch English Français ■■ Touch C to confirm your selection. The chosen language is now stored. The brand logo will light up on the display 3. The appliance will heat up and rinse itself, a small amount of water will run out of the drink outlet 4. The appliance is ready for use when the symbols and the display on the control panel are lit.

FF The factory settings of the fully automatic coffee machine are programmed for optimal performance. The appliances switches off automatically after a configured time (see the section “Menu – Automatic shut-down”).

Own settings “Favourite”

FF When the appliance is used for the first time, after a service program has been run and when it has not been operated for a long period, the first beverage will not have the full aroma and should not be consumed.

This fully automatic coffee machine grinds fresh beans for every brewing. For optimum quality, store the beans in a cool place in sealed containers.

FF FF FF FF When the fully automatic coffee machine is first used, you will achieve a suitably thick and stable “crema” only after the first few cups have been dispensed. If the appliance is in use for a long period of time, water droplets will form on the ventilation slits. This is normal.

Own settings “Favourite”

The number of Favourites depends on the model of the appliance. The menu item “Favourite” can be used to store and change individual (personalised) beverages (see the section “Menu – Favourite”). Call up individual beverage ■■ Briefly touch R. ■■ Select one of the Favourites already stored with your own settings. ■■ Touch C to begin dispensing the beverage.

The appliance can be locked to protect children against scalding and burns. ■■ Touch R for at least 3 seconds. A key symbol appears on the display 3. The childproof lock is now active. It is no longer possible to operate the appliance. ■■ Touch R for at least 3 seconds. The key symbol disappears from the display 3. The childproof lock is now ­deactivated. The appliance can be used in the usual way.

Important: Fill the water tank 5 with fresh clean water every day. The tank 5 should always contain sufficient water for operating the appliance. Cups should be prewarmed, e.g. with hot water. This applies particularly to small thick-walled espresso cups.

FF For a number of settings, coffee is prepared in two stages (see “­aromaDouble Shot”). Please wait until the process is completely finished.

Different beverages can be prepared just by touching a key. Drink selection Touching the appropriate symbol selects the desired drink. Your selection is indicated by lines above and below the symbol. The name of the drink and the currently active values for strength and cup size are shown in display 3. You can choose from the following drinks: Espresso Latte Macchiato Espresso Macch. Caffe Latte Coffee Milk froth Cappuccino Touch the “special beverages” button several times to select different drinks one after the other: Hot water Americano * Warm milk * Flat White * Coffee pot * Cafe Cortado * Kleiner Brauner * Items marked * are not present in all models.

Adjusting the strength, selecting ground coffee Touch H to set the strength of your coffee individually or to specify that ground coffee is to be used. The following settings are possible: very mild very strong mild doubleshot strong regular doubleshot strong+ strong Ground coffee ■■ Touching the appropriate symbol selects the desired drink. ■■ Touch H repeatedly until the desired setting e.g. strong or Ground coffee (see the section “Preparation using ground coffee”) appears on the display. aromaDouble Shot The longer the coffee is brewed, the more bitter substances and undesired aromas are released. This has a negative effect on the taste and makes the coffee less easily digestible. So for extra strong coffee, the appliance has a special aromaDouble Shot function. When half the quantity has been prepared, it grinds and brews fresh coffee beans so that only the pleasant, aromatic scents are released.

FF The aromaDouble Shot function can be selected for any drink containing a proportion of at least 35 ml coffee volume. It is not available for small drinks such as a small espresso or when the G setting is enabled.

Select cup size Touching D individually selects the beverage volume desired. The following settings are possible: small medium large ■■ Touching the appropriate symbol selects the desired drink. ■■ Touch D repeatedly until the display indicates the desired setting.

FF An arrow or multiple arrows next to the setting, e.g. „large ˆ”, ­indicate that the preset capacity (see the section “Menu – Set cup size”) has been changed.

Two cups at once Once you have selected a black coffee or milky coffee drink (for some appliances, this applies only to black coffee), touching G prepares two cups simultaneously as soon as you touch C to begin dispensing. The setting is shown on the display. ■■ Touching the appropriate symbol selects the desired drink. ■■ Touch G. ■■ Place two prewarmed cups at left and right underneath the beverage outlet 4. ■■ Touch C to begin dispensing the beverage. The selected drink will be brewed and will then be dispensed into the two cups.

FF The drink is prepared in two stages (two grinding operations). Please wait until the process is completely finished.

FF Depending on the type of appliance the function “Two cups at once” may be available only for black coffee, not for milky coffee drinks.

Preparing coffee drinks

The appliance must be ready for use. ■■ Place a prewarmed cup underneath the beverage outlet 4. ■■ Touch the appropriate symbol to select the desired drink, Espresso or Coffee. The name of the drink and the currently active values for strength and cup size are shown in display.

FF You can change the cup size and coffee strength by touching D and H. If you select Ground coffee, follow the procedure described under “Preparation using ground coffee”.

For example: ■■ Touch D repeatedly until the display shows large. ■■ Touch H repeatedly until the display shows mild. ■■ Touch C to begin dispensing the beverage. The coffee is brewed and then dispensed into the cup.

FF You can touch C again to prematurely halt dispensing.

Preparation using milk

This fully automatic coffee machine possesses an integrated milk system that enables you to prepare coffee with milk or milk froth or warm milk alone.

FF Tip: It is also possible to use plantbased alternatives to milk, e.g. soya milk.

FF Note: The quality of the milk froth depends on the type of milk or the plant-based alternative used.

BB Risk of burns! The upper and lower sections of the milk system 4b become extremely hot. After use, always let them cool down before you touch them.

FF Caution! Dried milk residues are difficult to remove, therefore always clean (see the section “Cleaning the milk system”).

FF While milk is being prepared you may hear a whistling sound. This is due to the technical nature of the milk system 4b.

FF Touch C again to ­prematurely halt dispensing.

The appliance must be ready for use. The milk tube and suction pipe must be connected. ■■ Insert the suction pipe 4d into the milk container. ■■ Place a prewarmed cup or glass underneath the beverage outlet. Coffee-based drinks with milk ■■ Touch the appropriate symbol to select Espresso Macch., Caffe Latte, Latte Macchiato or Cappuccino. The name of the drink and the previously specified values for strength and cup size are shown in display.

FF You can change the cup size and coffee strength by touching D and H. If you select Ground coffee, follow the procedure described under “Preparation using ground coffee”.

■■ Touch C to begin dispensing the beverage. The milk or milk froth is dispensed into the cup or glass first. Then the coffee is brewed and runs into the cup or glass. You can touch C again to prematurely halt dispensing of the milk or coffee, touching C twice stops the entire dispensing process. Milk froth ■■ Touch the symbol to select Milk froth. ■■ Touch D to select the cup size. ■■ Touch C to begin dispensing the beverage. Milk froth is dispensed from the beverage outlet.

FF Hot water Before hot water is dispensed, the milk system should be cleaned and the milk tube removed (see the section “Cleaning the milk system”). If the milk system is not cleaned, small amounts of milk may be dispensed together with the hot water.

Americano * ■■ Place a prewarmed cup underneath the beverage outlet 4. ■■ Touch the “special beverages” symbol repeatedly until Americano appears on the display. ■■ Select settings such as the cup size and strength as described in the section “Preparing coffee drinks”. ■■ Touch C to begin dispensing the beverage. The coffee is brewed and then dispensed into the cup.

Touch the “special beverages” button several times to select different drinks one after the other. Items marked * are not present in all models.

BB Risk of burns! The milk system 4b becomes extremely hot. After use, always let it cool down before you touch it.

The appliance must be ready for use. ■■ Place a cup or glass underneath the beverage outlet 4. ■■ Touch the “special beverages” symbol repeatedly until Hot water appears on the display. ■■ Touch D to select the cup size. ■■ Touch C to begin dispensing the beverage.

FF If you see the message Please remove suction hose, proceed as follows:

■■ Take off the milk tube 4c and then touch C again. Hot water will flow out of the outlet 4.

FF You can touch C again to prematurely halt dispensing.

Warm milk * Please read through first and take note of the section “Preparation using milk”. Then: ■■ Touch the “special beverages” symbol repeatedly until Warm milk appears on the display. ■■ Touch D to select the cup size. ■■ Touch C to begin dispensing the beverage. Warm milk will flow out of the outlet 4.

You can touch C again to prematurely halt dispensing.

FF You can touch C again to prematurely halt dispensing.

Flat White *, Cafe Cortado * or Kleiner Brauner * Please read through first and take note of the section “Preparation using milk”. Then: ■■ Place a cup or glass underneath the beverage outlet 4. ■■ Touch the “special beverages” symbol repeatedly until Flat White, Cafe Cortado or Kleiner Brauner appears on the display. ■■ Select settings such as the cup size and strength as described in the section “Preparing coffee drinks”. ■■ Touch C to begin dispensing the beverage. The coffee is brewed and runs into the cup or glass. Milk or milk froth is dispensed depending on the beverage. The sequence of coffee/milk depends on the beverage.

FF You can touch C again to prematurely halt dispensing of milk or coffee. Touching C twice stops the entire dispensing process.

Pot function * ■■ Place a pot underneath the beverage outlet 4. ■■ Touch the “special beverages” symbol repeatedly until Pot function appears on the display. ■■ Touch H to select the desired coffee strength. ■■ Touch D to select the desired quantity (4 or 6 cups). ■■ Touch C to begin dispensing the beverage. The coffee is brewed and then dispensed into the pot.

FF You can touch C again to prematurely halt dispensing.

Adjusting the grind setting

You can use the rotary selector 11 to adjust the grind setting from coarse to fine.

FF Caution! Adjust the grind setting only while the grinding unit is running, otherwise you may damage the appliance.

AA Risk of injury! Do not reach into the grinding unit.

■■ With the grinding unit running, adjust the selector 11 from fine (a: turn anticlockwise) to coarse (b: turn clockwise). a

Preparation using ground coffee This fully automatic coffee machine can also be operated using ground coffee (but not instant coffee).

FF When using ground coffee, the setting for the strength of the coffee, dispensing two cups at once and aromaDouble Shot is not available.

The appliance must be ready for use. ■■ Place a prewarmed cup underneath the beverage outlet 4. ■■ Touch the appropriate symbol to select a black or milky coffee drink. ■■ Touch H repeatedly until the display shows Ground coffee. ■■ Open the ground coffee drawer 12. ■■ Place no more than two level measuring spoons of ground coffee in the drawer.

FF Caution! Do not place coffee beans or instant coffee in this drawer.

■■ Close the ground coffee drawer 12. ■■ Touch C to begin dispensing the beverage. The coffee is brewed and then dispensed into the cup.

FF Touch C again to ­prematurely halt dispensing.

FF The new setting will not become apparent until after the second cup of coffee.

FF For dark roast coffee beans, choose a finer grind, for lighter beans a coarser grind.

The menu is used for changing individual settings, accessing information and launching processes. ■■ Touch A to open the menu. In the display you will see the various setting options, the navigation symbols light up. The current setting is marked on the display. Navigating through the menu: I = move down B = confirm / store F = go back A = open the menu / exit from the menu

FF Touching I displays each setting or selection option in order. After you reach the lowest menu item the topmost one is shown again.

For example: Setting the coffee temperature to max. : ■■ Touch A. The menu is opened. ■■ Touch I repeatedly until the display shows Coffee temperature. ■■ Touch B, the display shows e.g. high. ■■ Touch I repeatedly until the display shows max. ■■ Touch B to store the setting. The display shows the confirmation. ■■ The menu item Coffee temperature appears. ■■ Touch F to exit from the menu. You can specify the following settings: Cleaning and care Starting the special service programmes. You can select Rinse the milk system, Descale, Clean or calc’nClean. ■■ Use I to choose the desired programme and touch B to confirm your choice. ■■ Touch C to begin running the programme.

FF Important: Be sure to take note of the section on “Service programmes”.

Info Service programmes (depending on the type of appliance) Display how many beverages can still be prepared before it will be necessary to run one of the service programmes. ■■ Use I to display Clean after --- c or Descale after --- c. ■■ Touch F to exit from the display.

FF For technical reasons the counter does not represent a precise number of cups.

Coffee-milk ratio * The coffee-milk mixing ratio set in the factory can be adjusted in several steps. ■■ Use I to select the beverage (only for coffee drinks with milk) and confirm with B. ■■ Use I to select the desired mixing ratio (setting of milk content in %) and confirm with B. ■■ The setting is saved. Example: If a value of 30% is selected, 30% milk and 70% coffee will be dispensed. Items marked * are not present in all models. Favourite The menu item Favourite can be used to create or change personalised beverages. The number of Favourites depends on the model of the appliance. ■■ Use I to select a new or existing profile and confirm with B ■■ Touch the desired beverage and confirm with B. ■■ Your selection for the beverage settings appears on the display depending on the beverage, e.g. ml or Coffee-milk ratio. ■■ Make your settings and confirm with B each time. ■■ The beverage is now saved in the profile. Set cup size Set up the volume dispensed for each drink and each size of cup. The volumes set up in the factory can be adjusted stepwise. ■■ Use I to choose a drink and touch B to confirm your choice. ■■ Use I to choose the desired volume and touch B to confirm your choice. The setting is then saved. Water hardness Set this to the hardness of the local water supply. Level 1, 2, 3, 4 or Softening system can be selected. The preset level of water hardness is level 4.

■■ Use I to choose the desired water hardness and touch B to confirm your choice.

FF It is important to set the water hardness correctly, so that the appliance indicates accurately when the ­descaling programme should be run.

You can check the water hardness using the enclosed test strip or by asking your local water supplier. If a water softening system is installed in the house, please select the Softening system setting. ■■ Briefly dip the test strip in the water and check the result after one minute. Level Water hardness German (°dH) French (°fH) 1 1-7 1-13 2 8-14 14-25 3 15-21 26-38 4 22-30 39-54

FF A water filter lessens limescale deposits and reduces impurities in water. The appliance also does not need to be descaled so often.

Water filters are available from retail outlets or from customer services (see the section “Accessories”).

FF Important: Before you can use a new water filter it will need to be rinsed.

■■ Immerse the water filter with the opening facing upwards in a container filled with cold water. ■■ Gently compress the sides of the filter until no more air bubbles rise to the surface and the water filter rests on the base of the container. ■■ Use the measuring spoon 8 to press the water filter firmly into the water tank 5.

Automatic shut-down Setting how long the appliance should wait after the last drink was prepared before it automatically switches itself off. You can specify values from 15 minutes to 3 hours. The factory setting is 30 minutes. ■■ Use I to choose the desired interval and touch B to confirm your choice. Coffee temperature Specifying the temperature for coffee drinks and hot water. You can choose normal, high, or max. The setting applies to all types of drink preparation. ■■ Use I to choose the desired temperature level and touch B to confirm your choice. Water filter Specifying whether a water filter should be activated or whether no filter is used. You can choose Activate new filter or No filter.

■■ Fill the water tank with water up to the “max” mark. ■■ Connect the milk tube 4c to the milk system 4b and the suction pipe 4d. ■■ Insert the end of the suction pipe 4d into the drip plate 17b. ■■ Touch A and use I to select Water filter. ■■ Touch B and use I to select Activate new filter. ■■ Empty the drip tray and re-insert. ■■ Touch B to confirm. Water will now flow through the filter to rinse it. ■■ Then empty the drip tray and re-insert. The appliance is ready for use again.

Care and daily cleaning

FF Rinsing the filter simultaneously activates the setting for displaying the message “Please change water filter”. When this message appears, or at the latest after two months, the filter will no longer be effective. It needs to be replaced for reasons of hygiene and to prevent a build-up of limescale (which could damage the appliance).

If you do not intend to insert a new filter, select the setting No filter and touch B to confirm.

FF If the appliance has not been used for a prolonged period (for example, while you are on holiday), the existing filter should be rinsed before the appliance is used again. To do this, simply dispense a cup of hot water.

Languages Setting up the language to be used for display texts. ■■ Use I to choose the desired language and touch B to confirm your choice. Frost protection Service programme to prevent frost damage during transportation and storage. This programme completely empties the appliance.

Beverage statistics (depending on the type of appliance) Shows the volume of drinks dispensed since the appliance was taken into service. ■■ Touch F to exit from the display. Factory settings Resets your own settings to the condition when delivered. ■■ Touch C to clear all your own settings.

Care and daily cleaning

EE Risk of electric shock! Before cleaning the appliance, unplug it from the mains. Never immerse the appliance in water. Do not use a steam cleaner.

■■ Wipe the outside of the appliance with a soft, damp cloth. ■■ Clean the control panel with a microfibre cloth. ■■ Do not use any cleaning agents containing alcohol or spirits. ■■ Do not use abrasive cloths or cleaning agents.

FF The appliance must be ready for use and the water tank 5 must be filled.

■■ Touch C to begin running the programme. ■■ Remove the water tank; the appliance automatically empties all its pipes and then switches itself off. ■■ Empty the water tank 5 and the drip tray 17. Key tones Switches on or off the tones that you hear when you touch the control panel. ■■ Touch B to confirm your choice. ■■ Use I to choose Key tones ON or Key tones OFF and touch B to confirm your choice.

■■ Always immediately remove any limescale, or residues of coffee, milk, cleaning or descaling solution. It is possible for corrosion to form underneath such deposits. ■■ New sponge cloths may contain salts that can cause rust films to form on stainless steel, so such cloths should always be thoroughly rinsed before use.

Care and daily cleaning

■■ Pull the drip tray 17 and coffee grounds container 17c towards the front and remove them. Take off the panel 17a and drip plate 17b. Empty and clean the drip tray and coffee grounds container. ■■ Wipe out the inside of the appliance (holder, trays) and the drawer for ground coffee (this cannot be removed). ■■ Remove the float 17d and clean it with a moist cloth (depends on the type of appliance).

LL Do not put the following parts in the dishwasher: Panel of drip tray 17a, cover 4a, brewing unit 14, water tank 5 and aroma cover 10.

MM The following parts may be cleaned in the dishwasher: Drip tray 17, drip plate 17b, coffee grounds container 17c, measuring spoon 8 and the upper and lower parts of the milk system 4b.

FF Important: The drip tray 17 and coffee grounds container 17c should be emptied and cleaned every day in order to prevent deposits.

Cleaning the milk system

FF The milk system 4b is automatically cleaned with a short jet of steam directly after preparing a milk drink. Clean the milk system manually once a week or more frequently if required. For particularly thorough cleaning, the milk system 4b can be automatically rinsed with the programme “Cleaning the milk system” (see the section “Service programmes – Cleaning the milk system”).

BB Risk of burns! The milk system 4b becomes extremely hot. After use, always let them cool down before you touch them.

Take the milk system 4b apart to clean it: ■■ Push the beverage outlet 4 right down. ■■ Take off the cover 4a towards the front and pull off the milk tube.

FF If the appliance is cold when switched on, or if it is switched off after dispensing coffee, it rinses automatically. The system is therefore self-cleaning.

FF Important: If the appliance is not used for a lengthy period (e.g. while you are on holiday), clean the entire appliance thoroughly, including the beverage dispenser 4, milk system 4b, drip tray 17 and brewing unit 14.

■■ Remove the milk system 4b by pulling it straight forward.

Care and daily cleaning

■■ Clean the milk system holder 4e thoroughly to remove any coffee residues.

Cleaning the brewing unit (Figure G)

FF See also the Quick reference guide in the storage compartment 16.

■■ Take apart the upper and lower parts of the milk system 4b.

In addition to the automatic cleaning programme, the brewing unit 14 should be removed regularly for cleaning. ■■ Use the main switch J 1 to switch the appliance completely off. ■■ Open the door 13 to the brewing unit. ■■ Slide the red latch 14a on the brewing unit 14 all the way to the left. ■■ Press the eject lever 15 right down. The brewing unit will be released. ■■ Take hold of the brewing unit 14 by the recessed grips and carefully remove it.

FF Important: Clean it without using washing-up liquid and do not put it in the dishwasher.

■■ Separate the milk tube from the suction pipe. ■■ Clean the individual parts with washingup liquid and a soft cloth. ■■ Rinse all parts with clean water and dry them.

■■ Remove the cover 14b and thoroughly clean the brewing unit 14 under running water.

FF The upper and lower parts of the milk system 4b, the milk tube 4c and the suction pipe 4d can also be cleaned in a dishwasher.

■■ Reassemble the individual parts. ■■ Thoroughly clean the strainer of the brewing unit under the water jet.

■■ Place the milk system 4b back in the appliance from the front, making sure it is straight. ■■ Replace the cover 4a.

■■ Thoroughly clean the inside of the appliance with a moist cloth, removing any coffee residues. ■■ Allow the brewing unit 14 and the inside of the appliance to dry. ■■ Replace the cover 14b on the brewing unit and then push the brewing unit 14 back into the appliance until it latches into place. ■■ Press the eject lever 15 right up. ■■ Slide the red latch 14a all the way to the right and close the door 13.

FF See also the Quick reference guide in the storage compartment 16.

Following prior notification, either Descaling necessary or Cleaning necessary or calc’nClean necessary. appears in display 3 at certain intervals. The unit should immediately be cleaned or descaled using the appropriate programme. The two processes Descale and Clean can optionally be carried out together using the calc’nClean function (see the section “calc’nClean”). Failure to carry out the service programme according to the instructions may damage the appliance. Using a water filter increases the intervals until a descaling programme needs to be performed.

FF Important: if descaling is not performed on the appliance in good time, then the following appears: Descaling overdue. Appliance will soon be locked --> press menu for 3 sec. Immediately perform the descaling process in accordance with the instructions. If the appliance is locked, it can only be operated again once the descaling process has been carried out.

FF Caution! For each of the service programmes, use descaling and cleaning agents as described in the instructions. Never interrupt a service programme. Do not swallow any cleaning fluids! Never use citric acid, vinegar or any vinegar-based agents. Never place descaling tablets or other descaling materials in the coffee drawer 12!

Before starting the service program (Descale, Clean or calc’nClean) remove the brewing unit, clean it as instructed and replace it. Clean the milk system holder 4e thoroughly to remove any coffee residues. Specially developed suitable descaling and cleaning tablets are available from retail outlets or from customer services (see the section “Accessories”).

Cleaning the milk system

Takes about 1 minute. Touch A to open the menu. ■■ Use I to choose Cleaning and care and touch B to confirm your choice. ■■ Use I to choose Rinse the milk system and touch B to confirm your choice. ■■ Touch C to begin running the programme. The display 3 will indicate the progress of the programme: ■■ Place an empty glass under the beverage outlet 4 and stand the end of the suction pipe 4d in it. ■■ Touch C. The milk system will now clean itself automatically. ■■ Then empty the glass and clean the suction pipe 4d. You should also regularly clean the milk system manually (dishwasher or by hand, see the section “Care and daily cleaning”).

Takes about 30 minutes. The line at the bottom of the display 46

indicates the progress of the descaling process.

FF If there is a water filter in the water tank 5, be sure to remove it before starting the service programme.

■■ Touch A to open the menu. ■■ Use I to choose Cleaning and care and touch B to confirm your choice. ■■ Use I to choose Descale and touch B to confirm your choice. ■■ Touch C to begin running the programme. he display 3 will indicate the progress of the programme: ■■ Empty and re-insert the drip tray 17.

FF The following request appears: Remove water filter if inserted ¢start.

■■ Remove the filter and then touch C again. ■■ Pour lukewarm water into the empty water tank 5 up to the “0.5 l” mark and then dissolve one Siemens descaling tablet TZ80002N in it. ■■ Touch C. ■■ Place a container with a capacity of 0.5 litre under the beverage outlet 4. ■■ Place the end of the suction pipe 4d in the container. ■■ Touch C. The descaling programme will now run for about 20 minutes.

FF If there is not enough descaling solution in the water tank 5, you will see the prompt Refill descaler ¢start.

■■ Add more descaling solution and then touch C again. ■■ Rinse the water tank 5 and refill it with fresh water up to the “max” mark. ■■ If you use a filter, replace it now. ■■ Touch C. The descaling programme will now run for about 1 minute and rinse the appliance. ■■ Empty and re-insert the drip tray 17.

FF Important: Wipe over the appliance with a soft damp cloth to ensure that you immediately remove any traces of descaling solution. It is possible for corrosion to form underneath such deposits. New sponge cloths may contain salts that can cause rust films to form on stainless steel, so such cloths should always be thoroughly rinsed before use. Clean the suction pipe 4d of the drinks outlet particularly carefully.

The appliance has finished descaling and is ready for use again.

Takes about 9 minutes. The line at the bottom of the display indicates the progress of the descaling process. ■■ Touch A to open the menu. ■■ Use I to choose Cleaning and care and touch B to confirm your choice. ■■ Use I to choose Clean and touch B to confirm your choice. ■■ Touch C to begin running the programme. The display 3 will indicate the progress of the programme: ■■ Empty and re-insert the drip tray 17. ■■ Open the ground coffee drawer 12. ■■ Drop one Siemens cleaning tablet in the drawer 12 and close it. ■■ Touch C. The cleaning programme will now run for about 7 minutes. ■■ Empty and re-insert the drip tray 17. The appliance has finished cleaning and is ready for use again.

Takes about 43 minutes. calc’nClean combines the functions Descale and Clean. If both programmes are due to be carried out close together the fully automatic coffee machine will automatically suggest this service programme.

Tips on energy saving

The line at the bottom of the display indicates the progress of the descaling process.

FF If there is a water filter in the water tank 5, be sure to remove it before starting the service programme.

■■ Touch A to open the menu. ■■ Use I to choose Cleaning and care and touch B to confirm your choice. ■■ Use I to choose calc’nClean and touch B to confirm your choice. ■■ Touch C to begin running the programme. The display 3 will indicate the progress of the programme: ■■ Empty and re-insert the drip tray 17. ■■ Open the ground coffee drawer 12. ■■ Drop one Siemens cleaning tablet in the drawer 12 and close it. ■■ Touch C.

FF The following request appears: Remove water filter if inserted ¢start.

■■ Remove the filter and then touch C again. ■■ Pour lukewarm water into the empty water tank 5 up to the “0.5 l” mark and then dissolve one Siemens descaling tablet TZ80002N in it. ■■ Touch C. ■■ Place a container with a capacity of 1 litre under the beverage outlet 4. ■■ Place the end of the suction pipe 4d in the container. ■■ Touch C. The descaling programme will now run for about 28 minutes.

FF If there is not enough descaling solution in the water tank 5, you will see the prompt Refill descaler ¢start.

■■ Add more descaling solution and then touch C again. ■■ Rinse the water tank 5 and refill it with fresh water up to the “max” mark. ■■ If you use a filter, replace it now. ■■ Touch C. The descaling programme will now run for about one more minute, and then the 48

cleaning programme will run for about 7 minutes and rinse the appliance. ■■ Empty and re-insert the drip tray 17.

FF Important: Wipe over the appliance with a soft damp cloth to ensure that you immediately remove any traces of descaling solution. It is possible for corrosion to form underneath such deposits. New sponge cloths may contain salts that can cause rust films to form on stainless steel, so such cloths should always be ­thoroughly rinsed before use. Clean the suction pipe 4d of the drinks outlet particularly carefully.

The appliance has finished descaling and is ready for use again.

FF Important: If any of the service programmes is ever interrupted, for instance by a power failure, please proceed as follows:

■■ Rinse the water tank 5 and refill it with fresh water up to the “max” mark. ■■ Touch C. The appliance will be rinsed for approx. 2 minutes for safety reasons. ■■ Empty and re-insert the drip tray 17. The aborted service programme must be restarted.

Tips on energy saving

■■ When the fully automatic coffee machine is not in use, use the mains switch J 1 on the front of the appliance to switch it off. ■■ In the menu, set the Automatic shut-down period to 15 minutes. ■■ If possible, do not interrupt the dispensing of coffee or milk froth. Stopping a process prematurely results in higher energy consumption and the drip tray fills up more quickly. ■■ Descale the appliance regularly to avoid a build-up of limescale. Limescale residues cause higher energy consumption.

FF Caution! To prevent frost damage during transportation and storage, completely empty the appliance beforehand.

See the section “Menu – Frost protection”.

The fully automatic coffee machine has special compartments to hold the measuring spoon and the Quick reference guide. ■■ To store the measuring spoon 8, lift off the water tank 5 and place the spoon in the preformed recess 7. ■■ To store the Quick reference guide, open the door to the brewing unit 13 and insert the guide into the space provided 16.

The following accessories are available from retailers or from customer service: Accessories

J Dispose of packaging in an environ­ mentally­friendly manner. This appliance is labelled in accordance with European Directive 2012/19/EU concerning used electrical and electronic appliances (waste electrical and electronic equipment – WEEE). The guideline determines the frame­ work for the return and recycling of used appliances as applicable throughout the EU. Please ask your specialist retailer about current disposal facilities.

Guarantee The guarantee conditions for this appliance are as defined by our representative in the country in which it is sold. Details regarding these conditions can be obtained from the dealer from whom the appliance was purchased. The bill of sale or receipt must be produced when making any claim under the terms of this guarantee. Changes reserved.

Simple troubleshooting

Simple troubleshooting Problem The appliance no longer responds. The grinder will not start.

Remedial action Pull out the mains plug, wait 10 seconds, plug it back in. The appliance is too hot. Disconnect the appliance from the mains and leave to cool for one hour. Coffee or milk froth quality Build-up of limescale in the Descale the appliance varies widely. appliance. according to the instructions. Milk froth quality varies The quality of the milk Optimise the result through the widely froth depends on the type selection of the type of milk or of milk or the plant-based plant-based drink. alternative used. No hot water dispensed. The milk system or the Clean the milk system or the intake of the milk system is intake (see the section “Care soiled. and daily cleaning”). Too little milk froth, none The milk system or the Clean the milk system or the at all, or the milk system intake of the milk system is intake (see the section “Care is not taking in any milk. soiled. and daily cleaning”). Milk not suitable. Do not use milk that has been boiled. Use cold milk with a fat content of at least 1.5%. The milk system is assem- Moisten the upper and lower bled incorrectly. sections and fit them together. Build-up of limescale in the Descale the appliance appliance. according to the instructions. The milk/blended milk The milk used is too cold. Use lukewarm milk. drinks are too cold. The personally selected Coffee is ground too finely. Adjust the grinding level to a per-cup quantity is Pre-ground coffee is too coarser setting. Use a coarser not reached. Coffee fine. ground coffee. dispensing slows Heavy build-up of limeDescale the appliance to a trickle or stops scale in the appliance. according to the instructions. completely. Coffee has no “crema”. Unsuitable type of coffee. Use a type of coffee with a higher proportion of robusta beans. The beans are no longer Use fresh beans. fresh. The grinding setting is not Adjust the grinding unit to a finer suitable for the beans. setting. If you are unable to solve the problem, always call the hotline! You will find the telephone numbers at the back of these instructions.

Cause Fault in the appliance

Simple troubleshooting Problem Coffee is too “acidic”.

Coffee is too “bitter”.

The coffee tastes “burnt”.

The appliance is not dispensing drinks The appliance is not dispensing drinks The water filter does not stay in position in the water tank. The coffee grounds are not compact and are too wet. Water dripped onto the inner floor of the appliance when the drip tray was removed. Display shows Please refill bean container although the container is already full, or the grinder is not grinding any beans. Display ­Empty drip tray despite empty drip tray.

Cause The grinding setting is too coarse or the pre-ground coffee is too coarse. Unsuitable type of coffee. The grinding setting is too fine or the pre-ground coffee is too fine. Unsuitable type of coffee. The brewing temperature is too high The grinding setting is too fine or the pre-ground coffee is too fine. Unsuitable type of coffee. Air in the water filter.

Residues of limescale remover are blocking the water tank. The water filter is not fitted correctly. The grinding setting is too fine or too coarse, or not enough ground coffee has been used. Drip tray removed too early.

Remedial action Adjust the grinding unit to a finer setting or use finer pre-ground coffee. Use a darker roast. Adjust the grinding unit to a coarser setting or use coarser pre-ground coffee. Change the type of coffee. Reduce the temperature, see the section “Menu – Coffee temperature”. Adjust the grinding unit to a coarser setting or use coarser pre-ground coffee. Change the type of coffee. Dip the water filter in water until no more air bubbles escape, then replace the filter. Remove the water tank and clean thoroughly. Firmly press the water filter straight down into the tank connection. Adjust the grinding unit to a coarser or finer setting, or use 2 level measuring spoons of ground coffee. Wait a few seconds after the last drink was dispensed before removing the drip tray.

Beans are not falling into Gently tap the bean container. the grinding unit (beans too Possibly change the type of oily). coffee. When the bean container is empty, wipe it with a dry cloth.

Emptying is not detected When the appliance is switched when the appliance is on, remove and re-insert the switched off. drip tray. The drip tray is soiled. Clean the drip tray thoroughly. If you are unable to solve the problem, always call the hotline! You will find the telephone numbers at the back of these instructions.

Simple troubleshooting

Problem Display Fill with uncarbonated water or change filter

Cause Water tank inserted wrongly. Carbonated water in the water tank. Float is stuck in the water tank. New water filter not rinsed according to the instructions. Air in the water filter.

Water filter is old. Very frequent display that Water is too hard. descaling is necessary. Beverage dispenser blocked.

Display Please clean brewing unit, then replace it

Brewing unit is soiled. Too much pre-ground coffee in the brewing unit. The mechanism of the brewing unit is stiff.

Remedial action Insert water tank correctly. Fill the water tank with fresh tap water. Remove the tank and clean thoroughly. Rinse the water filter according to the instructions and switch on. Dip the water filter in water until no more air bubbles escape, then replace the filter. Insert a new water filter. Insert a water filter and activate (see chapter “Menu – Water filter”). Clean the beverage dispenser and the milk system intake (see the section “Care and daily cleaning”). Clean the brewing unit. Clean the brewing unit. Place no more than 2 level measuring spoons of ground coffee in the drawer. Clean the brewing unit (see the section “Care and daily cleaning”). Clean the brewing unit.

Display Brewing unit is soiled. Restart appliance Display Incorrect or insufficient Perform descaling programme Appliance not sufficiently descaler or excessive again descaled. Repeat the scale on appliance. process Display Appliance is too hot. Switch off appliance for 30 Leave the appliance to cool minutes. down Display The appliance has a fault. Please contact the hotline. Error Please contact the hotline If you are unable to solve the problem, always call the hotline! You will find the telephone numbers at the back of these instructions.

Technical specifications

Technical specifications Power connection (voltage – frequency) Power rating Maximum static pump pressure Maximum water tank capacity (without filter) Maximum capacity of the coffee bean container Length of power cable Dimensions (H x B x D) Weight, empty Type of grinding unit

BSH group is a Trademark Licensee of Siemens AG. Manufacturer´s Service for Siemens Home Appliances.

www.siemens-home.bsh-group.fr GB Great Britain BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton Milton Keynes MK12 5PT To arrange an engineer visit, to order spare parts or accessories or for product advice please visit www.siemens-home.bsh-group.com/uk Or call Tel.: 0344 892 8999* * Calls are charged at the basic rate, please check with your telephone service provider for exact charges.

IN India, Bhārat, BSH Household Appliances Mfg. Pvt. Ltd. Arena House, Main Bldg, 2nd Floor, Plot No. 103, Road No. 12, MIDC, Andheri East Mumbai 400 093 Toll Free 1800 209 1850* www.siemens-home.bsh-group.com/in * Mo-Sa: 8.00am to 8.00pm (exclude public holidays)

IS Iceland Smith & Norland hf. Noatuni 4 105 Reykjavik Tel.: 0520 3000 Fax: 0520 3011 www.sminor.is IT Italia, Italy BSH Elettrodomestici S.p.A. Via. M. Nizzoli 1 20147 Milano (MI) Tel.: 02 412 678 200 mailto:info.it@siemens-home. bsh-group.com www.siemens-home.bsh-group.com/it

* Calls are charged at the basic rate, please check with your telephone service provider for exact charges.

IL Israel C/S/B/ Home Appliance Ltd. 1, Hamasger St. North Industrial Park Lod, 7129801 Tel.: 08 9777 222 Fax: 08 9777 245 mailto:csb-serv@csb-ltd.co.il www.siemens-home.bsh-group.com/il

BSH group is a Trademark Licensee of Siemens AG. Manufacturer´s Service for Siemens Home Appliances.

BSH group is a Trademark Licensee of Siemens AG. Manufacturer´s Service for Siemens Home Appliances.

Beratung bei Störungen • Advice on troubleshooting • Conseils sur les problèmes • Consejos sobre problemas de • Consulenza su problemi

Service-Hotlines www.siemens-home.bsh-group.com AE AT

*Calls are charged at the basic rate, please check with your telephone service provider for exact charges

*Calls are charged at the basic rate, please check with your telephone service provider for exact charges

BSH group is a Trademark Licensee of Siemens AG. Manufacturer´s Service for Siemens Home Appliances. 07/18

Garantiebedingungen DEUTSCHLAND (DE)