SP 2003N - Juicer MIA - Free user manual and instructions

USER MANUAL SP 2003N MIA

Black and white photo of a black MJMe juicer with a red lid and orange flame (no visible text or symbols)

Bedienungsanleitung

Instruction manual

Mode d'emploi

Labeled diagram of a coffee maker with numbered parts for identification and assembly reference.

D Beschreibung

1 Sicherheitsbügel

2 Saftauslauf

4 Stainless steel sieve

5 ON/OFF switch P-0-1-2

6 Transparent lid

7 Filling opening

I Descrizione

Important safeguards....11

Scope of delivery....13

Tipps for using the juicer.... 13

Before the first use....13

Assembling the juicer....13

Operating the juicer....14

Cleaning and care.... 14

Remove blockage.... 15

Trouble shooting guide.... 16

Technical Data....16

Disposal....16

Warranty claims.... 16

IMPORTANT SAFEGUARDS

Carefully read and follow all instructions and safeguards before operating. Save the instructions for further reference. Keep this instruction together with the receipt and the guarantee card. If the appliance is handed over to other persons, also supply them with the instructions for use. When using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/or injury to persons.

Intended use: This appliance is suited for preparing juice. Only use the appliance for domestic purpose. The appliance is not suited for commercial or outdoor use. The safeguards must be followed closely and the appliance has to be used in the way indicated in these instructions. Any other use, especially misuse, can cause injuries or damage by electrical shock, fire, moving mechanical parts. In case of damage and accidents caused by not following this instruction for use the manufacturer assumes no liability.

• Ensure that the mains voltage rating of your power supply corresponds to the voltage requirements of the appliance (220-240 V\~, 50 Hz, AC). Always connect the appliance to a grounded wall socket.
• Always handle the power cord with care. Do not pull or strain the power cord. The power cord may never be folded or pinched. Always pull the plug to disconnect the power cord, never pull on the cord to disconnect it
• Do not leave the appliance unattended while it is connected to the power supply. Always switch OFF ('0' position) and unplug the appliance if it is not in use and before moving, cleaning and/or assembling or disassembling it.
• Additional protection may be obtained by fitting an earth-leakage circuit-breaker (IF=30mA) into your home installation. Please consult a qualified electrician.

• Do not operate any appliance if:

- power cord is damaged

- In case of malfunction or if it has been dropped or damaged in any manner.

Should the cord be damaged, it must be replaced by a competent qualified electrician(*) to avoid any danger. All repairs should be made by a competent qualified electrician(*).

Special tools are required to repair the appliance. In any case ask a (*) competent qualified electrician to check and repair it.

• Unplug the cord from the mains

• when malfunction occurs during use
• before cleaning
• after use and for storing.

- Do not operate the appliance with a damaged cord, if it is malfunctioning or has been dropped or damaged in any manner. Ask a (*) competent qualified electrician to check and repair it. Do never try to repair yourself.

(*) Competent qualified electrician : after sales department of the producer or importer or any person who is qualified, approved and competent to perform this kind of repairs in order to avoid all danger.

• Caution! An electric appliance is no toy! Never leave the appliance unsupervised when in use. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

• Explain to your children all risks which can be caused by electric current:

• Danger caused by hot parts of the appliance

• Danger by moving and / or sharp-edged parts

• Danger caused by electric current

• Keep the appliance at any time out of reach of children or persons who can not handle electric appliances properly. The appliance must be stored at a place which is unapproachable for children.

• Do not leave packaging components (plastic bags, cardboard, polystyrene, etc.) within the reach of children, as it could be dangerous - danger of suffocation!

NOTE: The appliance does only operate when the safety bail is locked properly! (Safety cut off when safety bail is unlocked).

• Caution risk of electric shock! Never immerse the appliance, cord or plug into water or any other liquid. Never place the appliance in a dishwasher.
• Do not use the appliance while standing on a wet ground or if your hands or appliance are wet. Do not pour or drip any liquids at the motor base or cord. When liquids are spilled on the motor base or under it, immediately switch OFF ('0' position), unplug and dry the motor base thoroughly.
• To avoid the risk of electric shock or damage of the appliance do not operate or store the appliance outdoors or in damp or wet areas. Always place the appliance on a clean, dry and frost-free surface where it is protected from excessive strain (i.e. mechanical or electrical shock, overheating, moisture).
• Additional protection may be obtained by fitting an earth-leakage circuit-breaker (IF=30mA) into your home installation. Please consult a qualified electrician.

• Caution risk of injuries to person! Moving parts, rotating blades - Extra wide filling opening!
• Never insert your fingers or any other objects (hair, clothes, cooking utensils, knives, screw drivers etc.) when the appliance is connected to the power supply.
• Always switch OFF ('0' position) wait for the motor to stop completely and unplug the appliance before removing the juicer lid or other attachments.
• Do not attempt to use other utensils but the food pusher provided to push down the food in the filling opening.
• Do not hold your face over the open filling hole during operation, juice and hard parts of the processed food could splash out of the filling opening.
• Do not touch the small cutting blades in the base of the filter basket. The blades are very sharp! Caution while handling the filter basket, always take the filter basket on the rim to remove, empty or clean. Clean the filter basket with caution and use a fine nylon brush for cleaning, do not use any force. Always assemble the appliance completely for storage. This guarantees that the blades cannot be touched unintentionally.
  • Always wait until the motor has stopped completely before disassembling, moving or cleaning the appliance.

• Caution risk of accidents, injury and damage!
- Before use always make sure that the appliance is properly and completely assembled.
- Do not operate the appliance when the appliance or any parts of it are damaged to avoid all risks. The appliance is damaged when there are any cracks, excessively broken or frayed parts, distortions or leaks, or when the gear on the motor base stalls or sticks. In this case, immediately stop using the appliance pull the plug and return the appliance (including any parts and accessories) to an authorized service centre for check and repair.
- Do not attempt to use the appliance by using any parts or accessories not recommended by the manufacturer. This is dangerous and can cause injury to user and damage to the appliance.
- Place the appliance on a stable, flat and dry surface which is large enough to work without any trouble to eliminate the risk of falling down. Do not place the appliance near edges of table or counter. Place it as closed as possible to the power socket. Take care that the cord never hangs over the edges of furniture and nobody can smash the appliance down by pulling the cord.
- Do not place the appliance on or near a hot gas or electric burner or on a heated oven and take care that the cord also never touches hot surfaces or sharp-edged objects. Do not place any kind of tissues or cloth under or on the appliance to avoid the risk of electrical shock or fire.

- Caution! Always switch off (power switch position "0") the appliance immediately and unplug after each use.

SCOPE OF DELIVERY

• Juicer
• Stainless steel sieve
• Sieve holder
  • Transparent splash protection lid
• Pusher
• Pulp container
• Instruction manual

TIPS FOR USING THE JUICER

The juicer makes it easy to prepare reshly made vegetable and fruit drinks efficiently. Some fruit and vegetables (e.g. apples, carrots) will not need to be cut, thanks to the extra wide feed opening of the juicer. Simply remove all uneatable parts: Seeds, stalks, stones, or hard paring etc. After juicing you may use the pulp (residues of processed fruit or vegetables) for delicious sauces, soups, desserts or just for the compost in your garden. The appliance is designed for a quick and easy cleaning after juicing fresh fruit, vegetables and herbs.

Do not leave any food residues dry on the surfaces of the appliance. If pulp is left to dry on the filter basket, it may clog the filter mesh. This will decrease the performance of the juicer. In this case soak the filter basket in hot soapy water to remove any dried pulp before using again (see care and cleaning). Do not use any abrasive cleaners or cleaning pads to avoid damage.

BEFORE THE FIRST USE

Carefully read and follow all instructions and safeguards before operating.

Remove all packaging, foils etc.

Place the appliance on a stable, flat and dry surface which is large enough to work without any trouble to eliminate the risk of falling down. Make sure before you assemble any parts that the appliance is not connected to the power supply and the switch is switched OFF (switch position '0'). Before the first use clean all removable parts which come in touch with food in slightly warm and soapy water, rinse and dry. Caution with the filter basket, the blades in the base are extremely sharp! Risk of injury! (See care and cleaning)

Note: Do not use the appliance for chopping, slicing, or shredding of hard foods and nutrients (i.e. nuts or chocolate). Do not use for mincing meat or pureeing.

ASSEMBLING THE JUICER

See the picture at 'list of parts' to get to know your juicer. For assembling refer to picture and following instruction.

Note: Treat your juicer and all parts with care and without using violence. Caution! Risk of injury! the blade inside of the sieve is very sharp! Assemble the appliance correctly and completely before each use!

Caution! Ensure that the item is switched OFF before connecting the appliance to the mains, to avoid accident by accidentally switching on. The blue lamp indicates connection to mains as long as plugged in.

• Place the sieve holder on top of the motor base. Press slightly down to fix it properly.
• Place the pulp container under the pulp outlet. The pulp container has to be positioned exactly under the outlet to guarantee splash protection. Place a juice container under the spout.

• Insert the stainless steel sieve centered in to the sieve holder. Always take the stainless steel sieve at the rim, to avoid the risk of injury by touching the sharp blades. Rotate the stainless steel sieve until it is seated properly on the gear. Caution! Make sure that the filter basket is mounted properly by rotating it slightly. The basket may not wobble or tilt. The filter basket must rotate easily and without rubbing on the filterbase.

• Place the pulp container into position. Place the pulp container under the juicer lid so that it fits into the cut out of the motorbase (see picture of list of parts). Push the pulp container into the guidance at the rim of the sieve holder. Position the pulp container before you close the juicer lid.

• Place the transparent lid over the sieve holder. The lid can only be mounted in one correct position. The filling opening must be centered above the stainless steel sieve. The juicer lid must be placed exactly on the sieve holder to avoid splashing.
• Close bothsafety bails. They have to be engaged properly - otherwise the appliance will not operate!
• Align the food pusher into the guiding of the filling opening. The appliance is now ready for use.

• Wash your fruit and vegetables and remove all uneatable parts. Remove any hard and uneatable parts of the fruit and vegetables before juicing (i.e. stalks, hard paring, stones and seeds).
  TIP: Most fruit and vegetables such as apples, carrots and cucumbers will not need to be cut into small pieces, as they will fit into the extra wide filling opening of the juicer. Extereme hard and uneatable parts should be removed. When juicing carrots, put the strait end first into the filling opening.
• Ensure that the juicer is assembled correctly and the power switch is in the OFF (position '0', see assembling the juicer). Make sure that the juice container is placed direct under the spout and the pulp container is fixed correctly under the juicer lid (see assembling the juicer).
• Plug the mains plug into the next socket.
• Switch the power switch to the ON position (I) to start the motor.

CAUTION: If the motor begins to stall or stick during the operation, immediately switch OFF (position '0') and unplug the appliance (please refer to trouble shoting guide).

WARNING: Always use the food pusher provided to push the food down. Do never insert your hand or other objects into the open filling opening and always keep your face away during operation and when the appliance is connected to the power supply.

• With the motor running, remove the food pusher and put the prepared food into the filling opening. Do not overfill the filling opening. Gently push down the food. To extract the maximum amount of juice, push down the food slowly without any force.
• The juice will flow into the juice container and the pulp will concentrate in the pulp container.

CAUTION: Do not allow the pulp or juice container to overfill because this may cause overflow danger of electric current. To avoid overflow interrupt the extraction and empty the container before it is completely full. (See disassembling the juicer). Switch OFF the appliance (position '0') and wait until the motor has stopped completely. Unplug the appliance and put the container aside.

If you want to start extraction again, replace the pulp container and the juice container under the spout.

After juicing is complete: switch OFF (position '0') and wait until the motor has stopped completely. Always unplug the appliance after having finished the juicing process.

Always clean all removable parts immediately after juicing is complete. (See cleaning and maintenance). Never let food residues dry on the unit or the filter basket or other parts of the unit.

CLEANING AND CARE

Caution! Always switch OFF and unplug the appliance and wait for the motor standstill before cleaning or disassembling. Clean the appliance immediately after each use to avoid tack-drying of food residues.

To avoid any risk of electrical shock do not immerse cord, plug or appliance in water or other liquid. Do not pour or drip any liquids at the motor base or cord and do never place the motor base or power cord in an automatic dishwasher.

Disassembling the juicer

• Put the juice container and the pulp container aside.
• Unlock the safety bails, open the juicer lid. Remove the pulp container and juice cover.

WARNING: To avoid damage never use force to remove any parts of the juicer. Follow the instructions carefully to disassemble the unit.

WARNING: Beware of the sharp blades in the base of the stainless steel sieve. Do not touch the inner side of the sieve. Only take the sieve on its rim. Never let young children unattended, while the appliance or any part of it is reachable for them.

- Take the sieve holder with both hands and lift to remove it together with the filter basket inside. It needs a little power to remove the filter holder because for safety reason the sieve holder is well engaged. But do not use extreme violence to remove. After removing the sieve in the sieve holder can easily be removed and emptied out by taking it on the rim and turning it upside down.

Cleaning the juicer

Note: Discoloration of plastic parts may occur when processing strongly coloured fruit and vegetables.

Discoloration is harmless. To avoid it, rinse all removable parts after each use immediately under clear water and clean in warm soapy water by using a fine plastic brush.

- Disassemble the unit following the instructions ‘Dissassembling the juicer’.

CAUTION: To avoid damaging the surface of the unit never use abrasive cleaners, cleaning pads or any sharp objects (i.e. metal scouring pads). Use fine plastic brushes, and warm soapy water. Always handle the appliance and the parts with care and without any force.

• Place the sieve in hot soapy water for a few minutes. Clean all removable parts (sieve, sieve holder, juicer lid, food pusher and pulp container) in warm soapy water. Caution with the filter basket! Always take it on the rim and rinse under clear water. Take a fine plastic brush and brush carefully inside out until all residues are removed. Clean all plastic parts with a soft cloth.
  • After cleaning rinse under clear water and let dry all parts.

TIP: All removable parts except the motor base can be cleaned in the dishwasher.

Never attempt to clean the motor base and powercord in the dishwasher.

• Wipe the motor base with a slightly damp soft cloth or sponge. Take care that water or other liquids can not drip or spill on the motor base.
• Thoroughly dry the motor base and all parts of the appliance after each cleaning and, for some minutes, leave all parts dry naturally before storage. Always keep the appliance and all parts of it out of the reach of young children.
• To prevent the parts of the appliance from damage and being lost, re-assemble the appliance for storage (see assembling the juicer)

Storage:

Always clean the appliance before storing (see cleaning and maintenance). Make sure to store the appliance on a dry clean place, safe from frost, excessive strain (mechanical or electrical shock, heat, moisture) and out of the reach of children.

REMOVE BLOCKAGE

When juicing hard and fibrous food or working too fast or pushing the food pusher too firmly down, excessive wet pulp may build up in the filter basket and block the filter mesh.

• Immediately switch OFF (position '0'), wait until the motor has stopped completely and unplug the appliance.
• Put the juice container aside and remove the juicer lid (see disassembling the juicer)

WARNING: Beware of the sharp blades in the filter basket. Only take the filter basket on its rim.

- Use a little wooden oor plastic spoon to remove all pulp residues from the filter basket.

TROUBLE SHOOTING GUIDE

On any problems accuring, that are not described in the following instructions, please contact your authorized service center or the retailer.

The problem	The easy solution
The motor does not work when switched ON	The appliance is possibly not assembled properly.Refer to Assembling the juicer
The motor begins to stick or stall	Immediately switch OFF the juicer and unplug from the socket. Refer to Remove blockage.
Excessive pulp build-up in the filter basket	Immediately switch OFF the juicer and unplug from the socket. Refer to Remove blockage.
The pulp is too wet and the amount of juice you get is insufficient	Try to work slower. Remove the filter basket (See disassembling the juicer and cleaning and maintenance) and clean the filter basket from excessive residues built up in the fine mesh and blocking it. Brush the filter basket under running water. Caution with the sharp blades!
Juice leaks between the rim of the filter basket and the juicer lid	Try to work slower. Push the food pusher down gently and slowly. If necessary empty the pulp container (see disassembling the juicer and cleaning and maintenance)
Juice sprays out of the spout	Try to work slower. Push the food pusher down gently and slowly.
Juice overflows the brim of motor base	Immediately switch OFF the juicer and unplug from the socket. Possibly the juicer attachment and/or the spout are blocked. Clean the juicer attachment (see Cleaning and maintenance).

• If the mesh is still blocked: Remove the filter basket (see disassembling the juicer) and thoroughly clean the mesh under running water using a fine brush. Brush from the inside of the filter basket out.
• Assemble the unit properly and completely (see assembling the juicer) and continue juicing.
• If the mesh is blocked again, clean the appliance completely. Refer to Cleaning and Maintenance.

TECHNICAL DATA

Model: SP 2009

Power supply 220-240V\~50Hz

Power output: 250W

class: II

This appliance is tested according to GS regulations and corresponds to CE directives.

DISPOSAL

Notice for environmental: If at any time in the future you should need to dispose of this product please note that waste electrical products should not be disposed of with household waste. The symbol (on the right) on the packing is indicating it. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive)

WARRANTY CLAIMS

The guarantee period for this appliance is 24 months. The guarantee starts from the date of purchase (cash receipt). In case of malfunction you may send the appliance to your dealer, please add information about the malfunction and the original purchase receipt (which is obligatory for a repair free of charge)

Within the guarantee period we repair defects of the appliance, which are based on material or manufacturing faults, in our choice by repair or exchange. These obligations do not extend the period of guarantee. No claim on a new period of guarantee results from it.

An exact description of the complaint reduces the processing time.

We apologise for any inconvenience, that any claims of good-will are excluded:

• after expiry of the lifetime due to the construction and especially for batteries, accumulators, electric lamps etc.
• for consumption accessories and wear parts such as driving belts, motor coals, tooth brushes, grinding attachments, dough hooks, beaters, mixer attachments, round cutters etc.
• in case of breakage, as e.g. glass, porcelain or plastic
• in case of damages in transport, misuse, as well as
• in case of lack of care, cleaning and maintenance and in case of non observance of operation or mounting instructions
• in case of chemical and/or electrochemical effects
• in case of operation with wrong type of current respectively voltage and in case of connecting to unsuitable power sources
• in case of abnormal environmental conditions and in case of strange operation conditions
• as well as then, if repairs or illegal abortions are made by persons, who are not authorised by us or
• if our appliances are equipped with spare parts, supplementary parts or accessories, which are not original parts or
• if contact with unsuitable material have caused the damage

Subject to technical alterations