65HL15W64 - TV HITACHI - Free user manual and instructions

USER MANUAL 65HL15W64 HITACHI

Class 1 Laser Product: This product contains Class 1 laser source that is safe under reasonably foreseeable conditions of operation. Caution, See Operating Instructions: The marked area(s) contain(s) user replaceable coin or button cell batteries.

Hazardous Live Terminal: The marked terminal(s) is/are hazardous live under normal operating conditions. Protective Earth Connection: The marked terminal is intended for connection of the protective earthing conductor associated with the supply wiring. Class II Equipment With Functional Earthing: This appliance is designed in such a way that it does not require a safety connection to electrical earth, the earth connection is used for functional purposes. Class II Equipment: This appliance is designed in such a way that it does not require a safety connection to electrical earth. The following symbols are used on the product as a marker for restrictions and precautions and safety instructions. Each explanation shall be considered where the product bears related marking only. Note such information for security reasons. Markings on the Product Maintenance Risk of electric shock Caution

Warning: Batteries must not be exposed to excessive

KHDWVXFKDVVXQVKLQH¿UHRUWKHOLNH ‡Do not place any heat sources such as electric heaters, radiators, etc. near the TV set. ‡Do not place the TV on the floor and inclined surfaces. ‡To avoid danger of suffocation, keep plastic bags out of the reach of the babies, children and domestic animals. ‡Carefully attach the stand to the TV. If the stand is

SURYLGHGZLWKVFUHZVWLJKWHQWKHVFUHZV¿UPO\WR

prevent the TV from tilting. Do not over-tighten the screws and mount the stand rubbers properly. ‡Do not dispose of the batteries in fire or with

WARNING: Never let people (including

children) with reduced physical, sensory or mental capabilities or lack of experience and / or knowledge use electrical devices unsupervised. ‡Use this TV set at an altitude of less than 2000 meters above the sea level, in dry locations and in regions with moderate or tropical climates. ‡The TV set is intended for household and similar general use but may also be used in public places. ‡For ventilation purposes, leave at least 5cm of free space around the TV. ‡The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains, etc. ‡The power cord plug should be easily accessible. Do not place the TV, furniture, etc. on the power cord. $GDPDJHGSRZHUFRUGSOXJFDQFDXVH¿UHRUJLYH you an electric shock. Handle the power cord by the plug, do not unplug the TV by pulling the power cord. Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock. Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced,

WKLVVKRXOGRQO\EHGRQHE\TXDOL¿HGSHUVRQQHO

‡Do not expose the TV to dripping or splashing of OLTXLGVDQGGRQRWSODFHREMHFWV¿OOHGZLWKOLTXLGV such as vases, cups, etc. on or over the TV (e.g., on shelves above the unit). ‡Do not expose the TV to direct sunlight or do not SODFHRSHQÀDPHVVXFKDVOLWFDQGOHVRQWKHWRSRI or near the TV. IMPORTANT - Please read these instructions fully before installing or operating Note: Follow the on screen instructions for operating the related features. The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable. If the TV set is not disconnected electrically from the mains, the device will still draw power for all situations even if the TV is in standby mode or switched off. In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).

CAUTION Safety Information WARNING

WALL MOUNTING WARNINGS

Apparatus connected to the protective earthing of the building installation through the MAINS connection or through other apparatus with a connection to protective earthing – and to a television distribution system using coaxial cable,

PD\LQVRPHFLUFXPVWDQFHVFUHDWHD¿UHKD]DUG

Connection to a television distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11) WARNING

‡7LJKWHQWKHZDOOPRXQWLQJVFUHZV¿UPO\WRSUHYHQW

the TV from fall. Do not over-tighten the screws. ‡8VHWKHVSHFL¿HGZDOOPRXQWLQJVFUHZVDQGRWKHU accessories. ‡Do not install the TV on a ceiling or on an inclined wall. ‡The wall mount kit is optional. You can obtain from your local dealer, if not supplied with your TV. ‡Read the instructions before mounting your TV on the wall. English - 3 - ‡Educating children about the dangers of climbing on furniture to reach the television set or its controls. If your existing television set is being retained and relocated, the same considerations as above should be applied. ‡Not standing the television set on cloth or other materials placed between the television and supporting furniture. ‡Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support. ‡Ensuring the television set is not overhanging the edge of the supporting furniture. ‡Only using furniture that can safely support the television set. ‡Using cabinets or stands recommended by the manufacturer of the television set. Never place a television set in unstable or inclined locations. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as; WARNING If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. If the battery compartment does not close securely, stop using the product and keep it away from children. Keep new and used batteries away from children. This product or the accessories supplied with the product may contain a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Do not ingest the battery, Chemical Burn Hazard Features 1RWL¿FDWLRQ(depending on the model) This product contains technology subject to certain intellectual property rights of Microsoft. Use or distribution of this technology outside of this product is prohibited without the appropriate license(s) from Microsoft. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS 2.0+Digital Out is a trademark of DTS, Inc.© DTS, Inc. All Rights Reserved. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS or DTS-HD and the Symbol together are registered trademarks of DTS, Inc.© DTS, Inc. All Rights Reserved. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks, and DTS TruSurround is a trademark of DTS, Inc.© DTS, Inc. All Rights Reserved. YouTube and the YouTube logo are trademarks of Google Inc. The terms HDMI and High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, inc. in the United States and other countries. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. TRADEMARK ACKNOWLEDGMENT Content owners use Microsoft PlayReady™ content access technology to protect their intellectual property, including copyrighted content. This device uses PlayReady technology to access PlayReadyprotected content and/or WMDRM-protected content. If the device fails to properly enforce restrictions on English - 4 - Functions and features may vary in accordance with the model. ‡Audio Video Sharing

‡79VXSSRUWV8OWUD+' 8OWUD+LJK'H¿QLWLRQDOVR

known as 4K) which provides resolution of 3840 x 2160 (4K:2K). It equals 4 times the resolution of Full HD TV by doubling the pixel count of the Full HD TV both horizontally and vertically. Ultra HD contents are supported from HDMI, USB inputs and over DVB-T2 and DVB-S2 broadcasts. ‡Remote controlled colour TV ‡Fully integrated digital terrestrial/cable/satellite TV (DVB-T-T2/C/S-S2) ‡HDMI inputs to connect other devices with HDMI sockets ‡USB input ‡OSD menu system ‡Scart socket for external devices (such as DVD Players, PVR, video games, etc.) ‡Stereo sound system ‡Teletext ‡Headphone connection ‡Automatic programming system ‡Manual tuning ‡Automatic power down after up to eight hours. ‡Sleep timer ‡Child lock ‡Automatic sound mute when no transmission. ‡NTSC playback ‡AVL (Automatic Volume Limiting) ‡PLL (Frequency Search) ‡PC input ‡Game Mode (Optional) ‡Picture off function ‡Programme recording ‡Programme timeshifting ‡Ethernet (LAN) for Internet connectivity and service ‡802.11n WIFI Support via USB dongle 75 Ohm (unbalanced) 220-240V AC, 50Hz. Operating Voltage 0ºC up to 40ºC, 85% humidity max Operation temperature and operation humidity < 200 mW 5470 - 5725 MHz (CH100 - CH140) If used outside of own premises, general authorization is required In-door use only for 5470 MHz to 5725 MHz band General authorization required for network and service supply(not for spectrum) Italy Greece Luxembourg Radio transmission is prohibited for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Restriction 0.004% Lead. The mark shown on the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries as unsorted municipal waste, but use the return and collection systems available. If the batteries or accumulators included with this equipment display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury, or more than 0.002% Cadmium or more than, Information for Users in European Union Countries

‡'RQ¶WWU\WRUHFKDUJHEDWWHULHV'DQJHURIH[SORVLRQ

Replace batteries only with the same or equivalent type. Packaging and packaging aids are recyclable and should principally be recycled. Packaging materials, such as foil bag, must be kept away from children. Batteries, including those which are heavy metal-free, should not be disposed of with household waste. Please dispose of used battery in an environmentally friendly manner. Find out about the legal regulations which apply in your area. Instructions for waste Disposal: Disposal information The requirements for any country may change at any time. It’s recommended that user checks with local authorities for the current status of their national regulations for both 2.4 GHz and 5 GHz wireless LAN’s. Russian FedIn-door use only eration Norway Country English - 5 - General authorization required for outdoor use and public service In-door use only for 2454-2483.5 MHz France Restriction Bulgaria Country 7KLV GHYLFH LV LQWHQGHG IRU KRPH DQG RI¿FH XVH LQ all EU countries (and other countries following the relevant EU directive) without any limitation except for the countries mentioned below. Country Restrictions < 200 mW < 200 mW 5250 - 5350 MHz (CH52 - CH64) 2400 - 2483,5 MHz (CH1-CH13) 5150 - 5250 MHz (CH36 - CH48) Max Output Power < 100 mW Frequency Ranges (depending on the model)

:LUHOHVV/$17UDQVPLWWHU6SHFL¿FDWLRQV

Refer to back cover label Power Consumption (W) DTS TruSurround (depends on model) SRS TruSurround (depends on model) German Nicam On Screen Display RF Aerial Input Audio 10000 (with satellite) Channel Indicator 1000 (without satellite)

Number of Preset Channels Receiving Channels TV Broadcasting 6SHFL¿FDWLRQ content usage, content owners may require Microsoft to revoke the device’s ability to consume PlayReadyprotected content. Revocation should not affect unprotected content or content protected by other content access technologies. Content owners may require you to upgrade PlayReady to access their content. If you decline an upgrade, you will not be able to access content that requires the upgrade.

Note: Functional button indications on some menu screens may vary in accordance with the remote control of your TV. Follow the button functions located at the bottom of the screen. Note that if you perform First Time Installation, MY BUTTON 1&2 will return to their default function. These buttons may have default functions depending on the model. However you can set a special function to these

EXWWRQVE\SUHVVLQJRQWKHPIRU¿YHVHFRQGVZKHQRQD

GHVLUHGVRXUFHRUFKDQQHO$FRQ¿UPDWLRQPHVVDJHZLOOEH

displayed on the screen. Now the selected MY BUTTON is associated with the selected function. English - 6 - (61 QXPEHU LV DQ XQLTXH ,' QXPEHU IRU 1HWÀL[ FUHDWHG especially to identify your TV. \RXU(61 1HWÀL[If this feature is supported by your TV, you can view

2. 1HWÀL[/DXQFKHVWKH1HWÀL[DSSOLFDWLRQ

3. Numeric buttons: Switches the channel, enters a

number or a letter in the text box on the screen.

4. TV: Displays channel list / Switches to TV Source

5. Volume +/6. Internet: Opens the portal page, where you can

reach many web based applications

7. Menu: Displays TV menu

8. 2.&RQ¿UPVXVHUVHOHFWLRQVKROGVWKHSDJH LQ

TXT mode), views channel list (DTV mode)

9. Back/Return: Returns to previous screen, opens

index page (in TXT mode)

10. Info: Displays information about on-screen

content, shows hidden information (reveal - in TXT mode)

11. Media browser: Opens the media browsing screen

13. Coloured Buttons: Follow the on-screen

instructions for coloured button functions

14. Language: Switches among sound modes

(analogue TV), displays and changes audio/ subtitle language (digital TV, where available)

17. Pause: Pauses the media being played, starts

18. Play: Starts to play selected media

19. Stop: Stops the media being played

20. Rapid advance: Moves frames forward in media

21. Screen: Changes the aspect ratio of the screen

22. Subtitles: Turns subtitles on and off (where

again to superimpose the teletext over a normal broadcast picture (mix)

electronic programme guide

returns to previous screen

29. Programme +/30. Mute: Completely turns off the volume of the TV

31. Swap: Quickly cycles between previous and

current channels or sources

32. Source: Shows all available broadcast and

content sources Type LAN Subwoofer Connection (back)(*) Ethernet Connection (back)

Connection (side) USB Connection (side) YPbPr Video Connection (back) Headphone Connection (side) HEADPHONE YPBPR Side AV (Audio/Video) Connection (side) Side AV (Audio/Video) Connection (side) SPDIF (Optical Out) Connection (back) SPDIF (Coaxial Out) Connection (back) HDMI Connection (back) PC/YPbPr Audio Connection (side) PC/YPbPr Audio Connection (side) VGA Connection (back) Scart Connection (back) SIDE AV SIDE AV SPDIF AUDIO IN AUDIO IN Connector Cables YPbPr/PC Audio Cable (not supplied) Audio/Video Cable (not supplied) English - 7 - LAN / Ethernet Cable (not supplied) (not supplied) PC to YPbPr Connection Cable Side Audio/Video Connection Cable (supplied) Side AV Connection Cable ( not supplied) Side Audio/Video Connection Cable (supplied) PC/YPbPr Audio Cables (not supplied) Connections (depending on the model) CAM module Device (*))RUH[WHUQDOVXEZRRIHUFRQQHFWLRQ If you want to connect a device to the TV, make sure that both the TV and the device are turned off before making any connection. After the connection is done, you can turn on the units and use them. NOTE: When connecting a device via the YPbPr or Side AV input, you must use the connection cables to enable connection. See the illustrations on the left side. | You can use YPbPr to VGA cable to enable YPbPr signal via VGA input. | You cannot use VGA and YPbPr at the same time. | To enable PC/YPbPr DXGLR\RXZLOOQHHGWRXVHWKHVLGHDXGLR inputs with a YPbPr/PC audio cable for audio connection. | To enable PC/ <3E3U DXGLR \RX ZLOO QHHG WR XVH WKH Side AV input with a YPbPr/PC audio FDEOH IRU DXGLR FRQQHFWLRQ using the Side AV connection cable’s RED and WHITE inputs_,IDQH[WHUQDOGHYLFHLV

FRQQHFWHG YLD WKH 6&$57 VRFNHW WKH

TV will automatically switch to AV mode.| When receiving DTV channels (Mpeg4

+ RUZKLOHLQ0HGLD%URZVHUPRGH

output will not be available via the scart socket. | When using the wall mounting kit (available from third party in the PDUNHWLIQRWVXSSOLHG ZHUHFRPPHQG that you plug all your cables into the back of the TV before mounting on the wall. | Insert or remove the CI module only when the TV is SWITCHED OFF. You should refer to the module instruction manual for details of the settings. | The/Each USB input of your TV supports devices up to 500mA. Connecting devices that have current value above 500mA may damage your TV. | By connecting an HDMI cable to

\RXU79\RXKDYHWRXVHRQO\DVKLHOGHG

(high grade) HDMI cable to guarantee

-or- Rear side of the TV aerial cable satellite Connect the aerial or cable TV plug to the AERIAL INPUT (ANT) socket or satellite plug to the SATELLITE INPUT (LNB) socket located on the rear side of the TV. Antenna Connection (depending on the model) IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. Plug the power cable to the mains socket outlet. Connect Power To turn the TV off: Press the centre of the joystick in and hold it down for a few seconds, the TV will turn into standby mode. To turn on the TV: Press the centre of the joystick in, the TV will turn on. Note: Main menu OSD cannot be displayed via control button. To change source: Press the centre of the joystick in, the sources list will appear on the screen. Scroll through the available sources by pushing the joystick up or down. English - 8 - Note: You can move WKHVZLWFKXSZDUGRU downward to change the volume. If you want

press the middle of the switch once (Position 3) and then move upward or downward. If you press WKHPLGGOHRIWKHVZLWFKRQFHPRUHVRXUFH26' will be displayed. If you press the middle of the VZLWFKDQGKROGDERXWDIHZVHFRQGVWKH79ZLOO switch to standby mode. Main menu OSD cannot be displayed via control buttons. To change channel: Scroll through the stored channels by pushing the joystick up or down. To change volume: Increase the volume by pushing the joystick right. Decrease the volume by pushing the joystick left.

Note: The position of the joystick may differ depending on The joystick allows you to control the Volume / Programme / Source and Standby-On functions of the TV.

the model. ” buttons at the

-or- Note: Press “ ” and “ same time to view main menu. Volume +/- Programme +/- Source Standby/On TV and Operating Buttons (depending on the model) USB Connection ‡ Press the Standby button on the remote control or press the Standby button on the TV or press and hold the control switch on the TV until shut down, so the TV switches into standby mode (depends on the model). ‡Press the Standby button on the remote control or press the centre of the joystick on the TV in and hold it down for a few seconds, the TV will switch into standby mode. To Switch the TV Off (depending on model) ‡ Connect the power cord to the 220-240V AC, 50 Hz. ‡ Then the standby LED lights up. To switch on the TV from standby mode either: ‡ Press the Standby button, Programme +/- or a numeric button on the remote control. Control buttons on the TV (depending on model) ‡ Press the Standby button or Programme +/- button on the TV. The TV will then switch on. -or‡Press and hold the middle of the control switch on the left side of the TV until the TV comes on from standby. The TV will then switch on. -or‡Press the centre of the joystick on the TV in or push it up/down until the TV comes on from standby. To Switch the TV On Switching On/Off (depending on the model) The Auto TV OFF option(in the System>Settings>More menu) may be set to a value between 1 and 8 hours by default. If this setting is not set as Off and the TV has been left on and not been operated during the set time, it will switch into standby mode after the set time has expired. When you next switch-on the TV, the following message will be displayed. “TV switched to stand-by mode automatically because no operation was made for a long time.” Press OK to continue. If the TV does not receive any input signal (e.g. from an aerial or HDMI source) for 5 minutes, it will go into standby. When you next switch-on, the following message will be displayed: “TV switched to stand-by mode automatically because there was no signal for a long time.” Press OK to continue.

When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce energy consumption. Note: Screen Off option is not available if the Mode is set to Game. any button on the remote or on the TV to turn the screen on again. If pressed Right button while Auto option is selected or Left button while Custom option is selected, “Screen will be off in 15 seconds.” message will be displayed on the screen. Select Proceed and press OK to turn the screen off immediately. If you don’t press any ‡ To power down the TV completely, unplug the power cord from the mains socket. button, the screen will be off in 15 seconds. Press English - 9 - The Energy Saving settings can be found in the System>Picture menu. Note that some picture settings will be unavailable to be changed. Note: Available Energy Saving options may differ depending on the selected Mode in the System>Picture menu. If you set the Energy Saving to Minimum, Medium, Maximum or Auto the TV will reduce the energy consumption accordingly. If you like to set the BacklightWRD¿[HGYDOXHVHWDVCustom and adjust the Backlight (located under the Energy Saving setting) manually using Left or Right buttons on the remote. Set as Off to turn this setting off. This television is designed to be environment friendly. To reduce energy consumption, you can follow these steps: Environmental Information Remove the screw that secure the battery compartment FRYHU RQ WKH EDFN VLGH RI WKH UHPRWH FRQWURO ¿UVW Remove the cover gently. Insert two AAA batteries. Make sure the (+) and (-) signs match (observe correct polarity). Do not mix old and new batteries. Replace only with same or equivalent type. Place the cover back on. Then screw the cover back on again. Inserting the Batteries into the Remote CAUTION: Quickly plugging and unplugging USB devices, is a very hazardous operation. Especially, do not repeatedly quickly plug and unplug the drive. This may cause physical damage to the USB player and especially the USB device itself. You can connect USB devices to your TV by using the USB inputs of the TV. This feature allows you to

GLVSOD\SOD\-3*03DQGYLGHR¿OHVVWRUHGLQD86%

stick. It is possi ble that certain types of USB devices (e.g. MP3 Players) may not be compatible with this 79 <RX VKRXOG EDFN XS \RXU ¿OHV EHIRUH PDNLQJ any connections to the TV set in order to avoid any possible data loss. Note that manufacturer will not be UHVSRQVLEOHIRUDQ\¿OHGDPDJHRUGDWDORVV'RQRW

SXOORXW86%PRGXOHZKLOHSOD\LQJD¿OH

Using SatcoDX Feature (depending on the model) You can perform SatcoDX operations using the Installation>Satelite Settings menu. In the SatcoDX menu, there are two options regarding to the SatcoDx. You can download or upload SatcoDX data. In order to perform these functions a USB device must be connected to the TV. Note: 'R QRW WXUQ RII WKH 79 ZKLOH LQLWLDOL]LQJ ¿UVW

WLPHLQVWDOODWLRQ1RWHWKDWVRPHRSWLRQVPD\QRWEH

available depending on the country selection. (*) LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel number sequence (if available). While the search continues a message may appear, asking whether you want to sort channels according to the LCN(*). Select Yes and press OK WRFRQ¿UP. After the initial settings are completed TV will start to search for available broadcasts of the selected broadcast types. After all the available stations are stored, scan results will be displayed. Press OK to continue. The Edit Channel List menu will be displayed next. You can edit the channel list according to your preferences or press the Menu button to quit and watch TV. Press OK button on the remote control to continue and the Network/Internet Settings menu will be GLVSOD\HG LI \RX FRQ¿UP WKH SUHYLRXVO\ GLVSOD\HG message asking whether you want to do the network settings. Please refer to Connectivity section to

FRQ¿JXUHDZLUHGRUDZLUHOHVVFRQQHFWLRQ$IWHUWKH

settings are completed press OK button to continue. To skip to the next step without doing anything select No and press the OK button when the message is displayed asking whether you want to do the network settings. You can activate Store Mode option at this point.

7KLVRSWLRQZLOOFRQ¿JXUH\RXU79¶VVHWWLQJVIRUVWRUH

environment and depending on the TV model being used, the supported features of it may be displayed on the top of the screen as an info banner. This option is intended only for store use. It is recommended to select Home Mode for home use. This option will be available in System>Settings>More menu and can be turned off/on later. Additionally you can set a broadcast type as your favourite one. Priority will be given to the selected broadcast type during the search process and the channels of it will be listed on the top of the Channel List:KHQ¿QLVKHGSUHVVOK to continue. Analogue: If Analogue broadcast search option is turned on, the TV will search for analogue broadcasts after other initial settings are completed. English - 10 - ‡DiSEqC switch: If you have multiple satellite dishes and a DiSEqC switch, select this antenna type. Press OK to continue. You can set four DiSEqC options (if available) on the next screen. Press OK EXWWRQWRVFDQWKH¿UVWVDWHOOLWHLQWKHOLVW ‡Single Satellite Cable: If you have multiple receivers and a single satellite cable system, select this antenna type. Press OKWRFRQWLQXH&RQ¿JXUH settings by following instructions on the next screen. Press OK to scan for services. ‡Direct: If you have a single receiver and a direct satellite dish, select this antenna type. Press OK to continue. Select an available satellite on the next screen and press OK to scan for services. Satellite: If Satellite broadcast search option is turned on, the TV will search for digital satellite broadcasts after other initial settings are completed. Before satellite search is performed some settings should be made. Antenna Type menu will be GLVSOD\HG ¿UVW <RX FDQ VHOHFW Antenna Type as Direct, Single Satellite Cable or DiSEqC switch by using “ ” or “ ” buttons. Note: Searching duration will change depending on the selected Search Step. Digital Cable: If Digital Cable broadcast search option is turned on, the TV will search for digital cable broadcasts after other initial settings are completed.

$FFRUGLQJWR\RXURWKHUSUHIHUHQFHVDFRQ¿UPDWLRQ

message may be displayed before starting to search. Select YES and press OK to proceed. To cancel operation, select NO and press OK. You can select Network or set values such as Frequency, Network ID and Search Step.:KHQ¿QLVKHGSUHVVOK button. Digital Aerial: If Digital Aerial broadcast search option is turned on, the TV will search for digital terrestrial broadcasts after other initial settings are completed. About Selecting Broadcast Type Note: Depending on the Country selection you may be asked

WRVHWDQGFRQ¿UPD3,1DWWKLVSRLQW7KHVHOHFWHG3,1FDQQRW

be 0000. You have to enter it if you are asked to enter a PIN for any menu operation later. On the next screen, set your preferences using the directional buttons. When turned on for the first time, the language selection screen is displayed. Select the desired language and press OK. First Time Installation (depending on the model) Note: When the TV is switched into VWDQGE\ PRGH standby LED can blink to indicate that features such as

6WDQGE\6HDUFK2YHU$LU'RZQORDGRU7LPHULVDFWLYH

The LED can also blink when you switch on the TV from standby mode. Press Record button to start recording an event instantly while watching a programme. You can press Record button on the remote control again to record the next event after selecting the next programme Press Pause button while watching a broadcast to activate timeshifting mode. In timeshifting mode, the programme is paused and simultaneously recorded to the connected USB disk. Press Play button again to resume the paused programme from where you stopped. Press the Stop button to stop timeshift recording and return to the live broadcast. Timeshift cannot be used while in radio mode. You cannot use the timeshift fast reverse feature before advancing the playback with the fast forward option. Instant Recording (depending on the model) To use recording your USB drive should have 2 GB free space and be USB 2.0 compatible. If the USB drive is not compatible an error message will be displayed. To record long duration programmes such as movies, it is recommended to use USB Hard disk drives (HDD’s). Recorded programmes are saved into the connected USB disk. If desired, you can store/copy recordings RQWR D FRPSXWHU KRZHYHU WKHVH ¿OHV ZLOO QRW EH available to be played on a computer. You can play the recordings only via your TV. Lip Sync delay may occur during the timeshifting. Radio record is supported. The TV can record programmes up to ten hours. Recorded programmes are split into 4GB partitions. If the writing speed of the connected USB disk is not

VXI¿FLHQWWKHUHFRUGLQJPD\IDLODQGWKHWLPHVKLIWLQJ

feature may not be available. It is recommended to use USB hard disk drives for recording HD programmes. Do not pull out the USB/HDD during a recording. This may harm the connected USB/HDD. If the AC cord is unplugged while there is an active USB-recording timer setting, it will be cancelled. Multipartition support is available. A maximum of two

GLIIHUHQWSDUWLWLRQVDUHVXSSRUWHG7KH¿UVWSDUWLWLRQRI

the USB disk is used for PVR ready features. It also must be formatted as the primary partition to be used for the PVR ready features. Some stream packets may not be recorded because of signal problems, as a result sometimes videos may freeze during playback. Record, Play, Pause, Display (for PlayListDialog) keys can not be used when teletext is on. If a recording starts from timer when teletext is on, teletext is automatically turned off. Also teletext usage is disabled when there is an ongoing recording playback. Timeshift Recording (depending on the model) English - 11 - Recording a Programme (depending on the model) IMPORTANT: When using a new USB hard disk

using your TV’s Format Disk option in the Media Browser>Settings>Recording Settings menu.

USB disk to your TV while the TV is switched off. You should then switch on the TV to enable the recording feature. Note:KHQYLHZLQJLPDJH¿OHVWKH0HGLD%URZVHU

PHQXFDQRQO\GLVSOD\LPDJH¿OHVVWRUHGRQWKH

connected USB device. It is recommended to use the TV’s USB input(s) directly, if you are going to connect a USB hard disk. You can use USB hubs with your TV’s USB inputs. External power supplied USB hubs are recommended in such a case. Wait a little while before each plugging and unplugging

DVWKHSOD\HUPD\VWLOOEHUHDGLQJ¿OHV)DLOXUHWRGR

so may cause physical damage to the USB player and the USB device itself. Do not pull out your drive

While formatting USB hard drives which have more than 1TB (Tera Byte) storage space you may experience some problems in the formatting process.

IMPORTANT!%DFNXSWKH¿OHVRQ\RXUVWRUDJHGHYLFHV

before connecting them to the TV. Manufacturer will QRWEHUHVSRQVLEOHIRUDQ\¿OHGDPDJHRUGDWDORVV Certain types of USB devices (e.g. MP3 Players) or USB hard disk drives/memory sticks may not be compatible with this TV. The TV supports FAT32 and NTFS disk formatting but recording will not be available with NTFS formatted disks.

<RXFDQFRQQHFW´DQG´LQFK KGGZLWKH[WHUQDO

SRZHU VXSSO\ H[WHUQDO KDUG GLVN GULYHV RU 86% memory stick to your TV by using the USB inputs of the TV. Media Playback via USB Input (depending on the model) You can upload current services and related satellites & transponders in TV, to a USB device. Additionally you can download one of the SatcoDx ¿OHVVWRUHGLQ86%GHYLFHWRWKH79

:KHQ\RXVHOHFWRQHRIWKHVH¿OHVDOOVHUYLFHVDQG

related satellites and transponders in the selected

¿OHZLOOEHVWRUHGLQWKH79,IWKHUHDUHDQ\LQVWDOOHG

terrestrial, cable and/or analog services, they will be kept and only satellite services will be removed. Afterwards, check your antenna settings and make changes if necessary. An error message stating “No Signal” may be displayed if the antenna settings are QRWFRQ¿JXUHGSURSHUO\ The TV supports also ARC(Audio Return Channel) feature. This feature is an audio link meant to replace other cables between the TV and the audio system (A/V receiver or speaker system). To terminate this operation and control the TV via the remote again, press Quick Menu button on the remote, highlight the CEC RC Passthrough and set as Off by pressing Left or Right button. This feature can also be enabled or disabled under the System>Settings>More menu. The TV remote is automatically able to perform the main functions after the connected HDMI source has been selected. The CEC option in the System>Settings>More menu should be set as EnabledDW¿UVW3UHVVWKHSource button and select the HDMI input of the connected CEC device from the Sources List menu. When new CEC source device is connected, it will be listed in source menu with its own name instead of the connected HDMI ports name(such as DVD Player, Recorder 1 etc.). This function allows to control the CEC-enabled devices, that are connected through HDMI ports by using the remote control of the TV. CEC and CEC RC Passthrough (depending on the model) FollowMe TV (depending on the model) With your mobile device you can stream the current broadcast from your smart TV using the FollowMe TV feature. Install the appropriate Smart Center application to your mobile device. Start the application. For further information on using this feature refer to the instructions of the application you use. Note: This application may not be compatible with all mobile devices. HD channels are not supported and both of the devices must be connected to the same network. Start playback with the Play button and activate $OO¿OHVLQWKHOLVWZLOOEH continuously played in the same random order. $OO¿OHVLQWKHOLVWZLOOEH played once in random order Start playback with the Play button and activate

7KHVDPH¿OHZLOOEHSOD\HG

continuously (repeat) $OO¿OHVLQWKHOLVWZLOOEH continuously played in original order Start playback with the OK button and activate button and activate Start playback with the Play /oop/ShufÀe Mode Operation can set your Media Browser preferences by using the Settings Menu. When ARC is active, TV does not mute its other audio outputs automatically. So you need to decrease TV volume to zero manually, if you want to hear audio from connected audio device only (same as other optical or co-axial digital audio outputs). If you want English - 12 - <RX FDQ SOD\ SKRWR PXVLF DQG PRYLH ¿OHV VWRUHG on a USB disk by connecting it to your TV. Connect a USB disk to one of the USB inputs located on the side of the TV. Pressing the Menu button while in the Media Browser mode will access the Picture, Sound and Settings menu options. Pressing the Menu button again will exit from this screen. You IMPORTANT: Formatting your USB drive will erase

$//WKHGDWDRQLWDQGLW¶V¿OHV\VWHPZLOOEHFRQYHUWHG

WR)$7,QPRVWFDVHVRSHUDWLRQHUURUVZLOOEH¿[HG

after a format but you will lose ALL your data. If “USB disk writing speed too slow to record” message is displayed on the screen while starting a recording, try restarting the recording. If you still get the same error, it is possible that your USB disk does not meet the speed requirements. Try connecting another USB disk. Media Browser Menu (depending on the model) Note: Default PIN can be set to 0000 or 1234. If you have GH¿QHG WKH 3,1 LV UHTXHVWHG GHSHQGLQJ RQ WKH FRXQWU\ selection) during the First Time Installation use the PIN

Select the Recording Settings item in the Media Browser>SettingsPHQXWRFRQ¿JXUHWKHUHFRUGLQJ settings. Format Disk: You can use the Format Disk feature for formatting the connected USB disk. Your PIN is required to use the Format Disk feature.

5HFRUGLQJ&RQ¿JXUDWLRQ GHSHQGLQJRQWKH

model) If you press Pause button while watching recorded programmes, the slow forward feature will be available. You can use Rapid advance button to slow forward. Pressing Rapid advance button consecutively will change slow forwarding speed. Slow Forward Select Recordings from the Media Browser menu. Select a recorded item from the list (if previously recorded). Press the OK button to view the Play Options. Select an option then press OK button. Note: Viewing main menu and menu items will not be available during the playback. Press the Stop button to stop a playback and return to the Recordings. Watching Recorded Programmes (depending on the model) from within the EPG. Press Stop button to cancel instant recording. You can not switch broadcasts or view the media browser during the recording mode. While recording a programme or during the timeshifting, a warning message appears on the screen if your USB device VSHHGLVQRWVXI¿FLHQW Some options may not be available depending on the model and/or on the country selection in the First Time Installation. Note: Default PIN can be set to 0000 or 1234. If you

KDYHGH¿QHGWKH3,1 LVUHTXHVWHGGHSHQGLQJRQWKH

country selection) during the First Time Installation

XVHWKH3,1WKDW\RXKDYHGH¿QHG

Default CICAM PIN: This option will appear as greyed out if no CI module is inserted into the CI slot of the TV. You can change the default PIN of the CI CAM using this option. Set PIN:'H¿QHVDQHZ3,1QXPEHU Internet Lock: If this option is set to ON, the open browser application in the portal will be disabled. Set to OFF to release the application again. Child Lock: If this option is set to ON, the TV can only be controlled by the remote control. In this case the control buttons on the TV will not work. Note: If the country option in the First Time InstallationLVVHWDV)UDQFH,WDO\RU$XVWULDMaturity Lock’s value will be set to 18 as default. Maturity Lock: If this option is set, TV gets the maturity information from the broadcast and if this maturity level is disabled, disables access to the broadcast. Menu Lock: This setting enables or disables access to all menus or installation menus of the TV. To display parental lock menu options, a PIN number should be entered. After coding the correct PIN number, Parental Settings menu will be displayed. The Parental Settings menu options can be used to prohibit users from viewing of certain programmes, channels and using of menus. These settings are located in the System>Settings>Parental menu.

&RQ¿JXULQJ3DUHQWDO6HWWLQJV

You can use the Filter function in the Edit Channel ListPHQXWR¿OWHUWKHFKDQQHOVLQWKHChannel list permanently according to your preferences. Using this Filter option, you can set one of your four favourite lists to be displayed everytime the Channel list is RSHQHG 7KH ¿OWHULQJ IXQFWLRQ LQ WKH Channel list PHQXZLOORQO\¿OWHUWKHFXUUHQWO\GLVSOD\HGChannel listLQRUGHUWR¿QGDFKDQQHODQGWXQHLQWRLW7KLV changes will not remain the next time the Channel list is opened. the Channel Edit Options menu and select Add/ Remove Favourites option. Press the OK button again. Set the desired list option to On. The selected channel/s will be added to the list. In order to remove a channel or channels from a favourite list follow the same steps and set the desired list option to Off. English - 13 - You can create four different lists of your favourite channels. Enter the Channel List in the main menu or press the Green button while the Channel List is displayed on the screen in order to open the Edit Channel List menu. Select the desired channel on the list. You can make multiple choices by pressing the Yellow button. Then press the OK button to open Managing the Favourite Lists The TV sorts all stored stations in the Channel List. You can edit this channel list, set favourites or set active stations to be listed by using the Channel List options. Press the OK/TV button to open the Channel List<RXFDQ¿OWHUWKHOLVWHGFKDQQHOVE\SUHVVLQJWKH Blue button or open the Edit Channel List menu by pressing the Green button in order to make advanced changes in the current list. Using the Channel List General TV Operation E-Manual (depending on the model) <RX FDQ ¿QG LQVWUXFWLRQV IRU \RXU 79¶V IHDWXUHV LQ the E-Manual. To use E-Manual, press to the Info button while main menu is displayed on the screen or press Quick Menu button, select Information Booklet and press OK. By using the directional buttons select a desired category. Every category includes different topics. Select a topic and press OK to read instructions. To close the E-Manual screen press the Exit or Menu button. Note: The contents of the E-Manual may vary according to the model. Note: The audio device should support System Audio Control feature and CEC option should be set as Enabled.

$OORZVDQ$XGLR$PSOL¿HU5HFHLYHUWREHXVHGZLWK

the TV. The volume can be controlled using the remote control of the TV. To activate this feature set the Speakers option in the System>Settings>More menu as $PSOL¿HU. The TV speakers will be muted and the sound of the watched source will be provided from the connected sound system. System Audio Control Note: ARC is supported only via the HDMI1 input. to change connected device’s volume level, you should select that device from the source list. In that case volume control keys are directed to connected audio device. Note: Do not unplug the power cord while led is blinking during the reboot process. If the TV fails WR FRPH RQ DIWHU WKH XSJUDGH XQSOXJ ZDLW IRU WZR minutes then plug it back in. Your TV will search for new upgrades at 3:00 o’clock if Automatic scanning option in the Upgrade Options menu is Enabled and if the TV is connected to an aerial signal or to Internet. If a new software is found and downloaded successfully, it will be installed at the next power on. 3 AM search and upgrade mode If a new upgrade is found, it starts to download the

XSJUDGH$IWHUWKHGRZQORDGLVFRPSOHWHGFRQ¿UPWKH

question asking about rebooting the TV by pressing the OK to continue with the reboot operation. On the main menu select System and then More. Navigate to Software Upgrade and press OK button. In Upgrade Options menu select Scan for upgrade and press OK button to check for a new software upgrade. Software upgrade search via user interface

via the broadcast signal or via Internet. Software Upgrade It is not possible to set timer or record timer for two or more individual events at the same time interval. Notes: You cannot switch to any other channel while there is an active recording or timer on the current channel. Select Channel: Using this option, you can switch to the selected channel. Record / Delete Rec. Timer: Select the Record option and press the OK button. If the programme is going to be broadcasted at a future time, it will be added to Timers list to be recorded. If the selected programme is being broadcasted at the moment, recording will start immediately. To cancel an already set recording, highlight that programme and press the OK button and select the option Delete Rec. Timer. The recording will be cancelled. Set Timer on Event / Delete Timer on Event: After you have selected a programme in the EPG menu, press the OK button. Select Set Timer on Event option and press the OK button. You can set a timer for future programmes. To cancel an already set timer, highlight that programme and press the OK button. Then select Delete Timer on Event option. The timer will be cancelled. IMPORTANT: Connect a USB disk to your TV while the TV is switched off. You should then switch on the TV to enable the recording feature. English - 14 - Use the directional buttons to highlight a programme and press OK button to display Event Options menu. The following options are available. Programme Options Options (OK button): Displays event options. Event Details (Info button): Displays detailed information about selected programmes. Filter (Blue button): 9LHZV¿OWHULQJRSWLRQV Rec./Stop (Record button): The TV will start to record the selected programme. You can press again to stop the recording. Now/Next Schedule (*) ,Q WKLV OD\RXW RSWLRQ RQO\ the events of the highlighted channel will be listed. Prev. Time Slice (Red button): Displays the programmes of previous time slice. Next/Prev Day (Programme +/- buttons): Displays the programmes of previous or next day. Event Details (Info button): Displays detailed information about selected programmes. Filter (Text button): 9LHZV¿OWHULQJRSWLRQV Next Time Slice (Green button): Displays the programmes of next time slice. Options (OK button): Displays event options. List Schedule(*) Zoom (Yellow button): Press the Yellow button to see events in a wider time interval. Filter (Blue button): 9LHZV¿OWHULQJRSWLRQV Highlight Genre (Subtitles button): Displays Highlight Genre menu. Using this feature, you can search the programme guide database in accordance with the genre. Info available in the programme guide will be searched and results matching your criteria will be highlighted. Options (OK button): Displays event options. Event Details (Info button): Displays detailed information about selected programmes. Next/Prev Day (Programme +/- buttons): Displays the programmes of previous or next day. Search (Text button): Displays Guide Search menu. Now (Source button): Displays current event of the highlighted channel. Rec./Stop (Record button): The TV will start to record the selected programme. You can press again to stop the recording. Timeline Schedule Electronic Programme Guide (EPG) Some channels send information about their broadcast schedules. Press the Epg button to view the Programme Guide menu. There are 3 different types of schedule layouts available, Timeline Schedule, List Schedule and Now/Next Schedule. To switch between them follow the instructions on the bottom of the screen. Troubleshooting & Tips Connectivity Functions (depending on the model)

To connect the TV to the home network wirelessly just select Network Type as Wireless Device in Network Settings menu. The TV will search for available networks. Select the desired network and press OK. If the TV has a built-in WLAN system there is no need for additional devices to connect to a wireless network. For models with built-in WLAN system:

IMPORTANT,I\RXU79GRHVQRWKDYHEXLOWLQZL¿

feature, USB dongle is required to use wireless network features. Wireless connection

Connectivity feature allows the TV to connect to the home network wired or wirelessly. You can use this networking system to connect to the Internet Portal RU WR DFFHVV SKRWR YLGHR DQG DXGLR ¿OHV WKDW DUH stored on a media server connected to the network and play/display them on the TV. Wired connection Connect the TV to the modem/router via a LAN cable (not supplied). Select Network Type as Wired Device in Network Settings menu. Connecting TV to a Home Network To configure wired/wireless settings please refer to the Network Settings section in the System>Options Menu. English - 15 - If a “USB disk writing speed too slow to record” message is displayed on the screen while starting a recording, try restarting the recording. If you still get the same error, it is possible that your USB disk does not meet the speed requirements. Try connecting another USB disk. USB is too slow

7RUHFRUGDSURJUDPPH\RXVKRXOG¿UVWFRQQHFWD

USB disk to your TV while the TV is switched off. You should then switch on the TV to enable recording feature. If you cannot record, try switching off the TV and then re-inserting the USB device. Recording unavailable ‡Check the AV cables and connections if you have tried to connect a device. ‡If you cannot select an input source, it is possible that no device is connected. If not; Input sources - can not be selected ‡The batteries may be exhausted. Replace the batteries. Remote control - no operation ‡Sound may be coming from only one speaker. Check the balance settings from sound menu. ‡Check if the TV is muted. Press the Mute button or increase the volume to check. No sound ‡If you are in doubt, consult your dealer. ‡Are suitable plugs used to connect the antenna? ‡Is the antenna cable damaged? ‡Is the antenna connected properly? ‡This means your TV is not receiving any transmission. Make sure the correct source has been selected. No picture ‡The picture quality may degrade when two devices are connected to the TV at the same time. In such a case, disconnect one of the devices. ‡Check if you have entered the correct channel frequency if you have done manual tuning. ‡Low signal level can cause picture distortion. Please check antenna access. ‡Check if you have selected the correct TV system. Poor picture Make sure the power cord is plugged in securely to wall outlet. Check if batteries are exhausted. Press the Power button on the TV. Tv will not turn on

Audio Video Sharing Select Media Browser by using the directional buttons from the main menu and press OK. The media browser will then be displayed.

2. Play Shared Files via Media Browser

See the Wired/Wireless connection chapters for GHWDLOHGFRQ¿JXUDWLRQLQIRUPDWLRQ

1. Connect to a Wired or Wireless Network

Audio Video Sharing feature uses a standard that eases the viewing process of digital electronics and makes them more convenient to use on a home network. This standard allows you to view and play photos, music and videos stored in the media server connected to your home network. Using Audio Video Sharing Network Service Note: This feature may not be supported on all mobile devices. If available, you can download a virtual remote controller application from the server of your mobile device application provider. You can control the TV via your wireless handheld device using this application. To do this enable the Virtual Remote feature from the System>Options>More menu by pressing Left or Right button. Connect the TV and the mobile device to the same network and start the application. Enter the Media Browser menu and the playback device selection OSD will be displayed. Select your mobile device and press the OK button to continue. If the connection is established correctly, you will be

DEOHWRDFFHVVWKHVKDUHG¿OHVIURP\RXUPRELOHGHYLFH

via the Media Browser of your TV. Connect your mobile device to the router/modem and then activate the sharing software on your mobile

GHYLFH7KHQVHOHFW¿OHVWKDW\RXZDQWWRVKDUHZLWK

your TV. If your mobile device has WiFi feature, you can connect it to your TV via a router, in order to access the content in your device. For this, your mobile device must have an appropriate sharing software. Connecting to your mobile device via WiFi To disconnect from a network, you should highlight Network Type, press Left or Right button and set as Disabled. Audio Video Sharing support is only available in the Media Browser Folder mode. To enable folder mode, go to the Settings tab in the main media browser screen If the selected network is protected with a password, and press OK. Highlight View Style and set to Folder using the Left or Right buttons. Select the desired media enter the correct key by using the virtual keyboard. type and press OK. Wait until the IP the address is shown on the screen. If sharing configurations are set properly, Device This means that the connection is now established. Selection screen will be displayed after selecting the desired media type. If available networks are found, they will be listed on this screen. Select media server or English - 16 - You can press OK button to scan available networks for wireless connection. Afterwards, a list of networks will be displayed. Select your network from the list and press OK. Your TV’s network settings include wired and wireless connection options. If you are connecting the TV via ethernet input, select Network Type as Wired Device. Select Wireless Device option if you are going to connect the TV to your network wirelessly.

&RQ¿JXULQJ1HWZRUN6HWWLQJV

While using the wireless connection type, consider that the TV cannot connect to the networks with hidden SSID.

)RUPRGHOVZLWKRXWEXLOWLQZL¿V\VWHPFRQQHFWWKH

wireless adaptor to one of the USB inputs of the TV. PC/HDD/Media Player or any other devices that are compatible should be used with wired connection for higher playback quality. About Using Connectivity Feature

For models without built-in WLAN system:

Connecting Other Wireless Devices (depending on the model) Note: Possible application dependent problems may be caused by the content service provider. Press “Internet” button on the remote to open internet portal page. You will see icons of the available applications and services on the portal screen. Use the navigaiton buttons on your remote to select the desired one. You may view the desired content by pressing OK after selecting. Press BACK/RETURN button to return back to the previous screen or EXIT to quit internet portal mode Portal feature adds your TV a feature that allows you to connect to a server on the Internet and view the content provided by this server over your Internet connection. Portal feature allows you to view the music, video, clip or web content with defined shortcuts. Whether you can view this content without interruption depends on the connection speed provided by your internet service provider. Internet Portal Note: Wireless devices may operate within the same radio frequency range and may interfere with one another. To improve the performance of your wireless device place it at least 1 meter away from any other wireless devices. Note: Refer to the user manual of the wireless device to learn how to set the device to pairing mode. You can connect audio devices or remote controllers wirelessly to your TV. Unplug or switch off any other connected audio device in order for wireless connection feature to work correctly. For audio devices you should use the Audio Link option in the System>Sound menu, for remote controllers the Smart Remote option in the System>Settings>More menu. Select the menu option and press the OK button to open the related menu. Using this menu you can discover and connect the devices that use the same wireless technology and start to use them. Follow the on-screen instructions. Start the device discovery. A list of available wireless devices will be displayed. Select the device you want to connect from the list and press the OK button to connect. If “Device connected” message is displayed, the connection is successfully established. If the connection fails try it again. ‡Start device discovery on the TV ‡Set the device to pairing mode Your TV supports another short range wireless connection technology too. A pairing is required before using these kind of wireless devices with the TV set. You should do the followings to pair your device with the TV: English - 17 - There are different standards which enable sharing of screens including graphical, video and audio content between your mobile device and TV. 3OXJ WKH ZLUHOHVV 86% GRQJOH WR79 ¿UVW LI WKH79 doesn’t have internal WiFi feature. Then press the Source button on the remote and switch to Wireless Display source. A screen appears stating that the TV is ready for connection. Open the sharing application on your mobile device. These applications are named differently for each brand, please refer to the instruction manual of your mobile device for detailed information. Scan for devices. After you select your TV and connect, the screen of your device will be displayed on your TV. Note: This feature can be used only if the mobile device supports this feature. Scanning and connecting processes differ according to the programme you use. Android based mobile devices should have the software version V4.2.2 and above. Using with mobile devices Wireless Display is a standard for streaming video and sound content by Wi-Fi Alliance. This feature provides the ability to use your TV as wireless display device. Wireless Display (depending on the model) Note: There may be some PC’s which may not be able to utilize the Audio Video Sharing feature due to administrator and security settings (such as business PC’s). You can connect only one television to the same network. If a problem occurs with the network, please switch your television off at the wall socket and back on again. Trick mode and jump are not supported with the Audio Video Sharing feature. 6XEWLWOH ¿OHV GR QRW ZRUN LI \RX ZDWFK YLGHRV IURP your network through Audio Video Sharing feature. To play other media types from this screen, you must go back to main Media Browser screen and select the media type as desired and then perform the network selection again. Refer to the Media Browser menu

VHFWLRQIRUIXUWKHULQIRUPDWLRQRQ¿OHSOD\EDFN

If you select the media type as Videos and choose a device from the selection menu. Then select the

IROGHUZLWKYLGHR¿OHVLQLWRQWKHQH[WVFUHHQDQGDOO

WKHDYDLODEOHYLGHR¿OHVZLOOEHOLVWHG network that you want to connect to using the Up or Down buttons and press OK. If you want to refresh the device list, press the Green button. You can press Menu to exit.

PAL SECAM NTSC3.58 Available Supported Signals In some cases a signal on the TV may not be displayed properly. The problem may be an inconsistency with standards from the source equipment (DVD, Set-top box, etc. ). If you do experience such a problem please contact your dealer and also the manufacturer of the source equipment. (X: Not Available, O: Available) HDMI YPbPr Back AV (SCART) EXT Source AV and HDMI Signal Compatibility English - 18 - Note: Being able to use all functions of this application depends on the features of your TV. Download the appropriate Smart Center application onto your mobile device from the application store on the web and launch it to start to use. For media sharing feature Audio Video Sharing option in the System>Options>More menu of your TV should be enabled. To use Smart Center features, connections have to be done properly. Make sure the TV and mobile device are connected to the same network. Smart Center is a mobile application running on iOS and Android platforms. With your tablet or phone, you can easily stream your favourite live shows and programmes from your smart TV using its FollowMe TV technology. Also; you can launch your portal applications, use your tablet as a remote control for

\RXU79DQGVKDUHPHGLD¿OHV

Smart Center (depending on the model) Open Browser function is one of the applications on the portal that provides access to internet. Select the internet browser logo on the portal page and press

English - 19 - The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions. 720P@30fps 1080P@30fps 4K2K@60fps 4K2K@30fps Motion JPEG VP8 HEVC VP9

1400x1050 1600x900 English - 22 -

(3* (OHNWURQLVFKHU3URJUDPPIKUHU =HLJWGHQ

PLWJHOLHIHUW HPSIHKOHQ ZLU ,KQHQ EHYRU

FRP3URGXVVXEOLFHQĠD'76/LFHQVLQJ/LPLWHG'76

FRP3URGXVVXEOLFHQĠD'76/LFHQVLQJ/LPLWHG'76

DXWRPDW OD PRGXO $9_ $WXQFL FkQG

DXGLR UHFHSWRU$9VDXVLVWHPGHGLIX]RDUH

&RQHFWDĠLWHOHYL]RUXOODXQPRGHPURXWHUFXDMXWRUXO

03 PSPRY *33 JSSJS $9, DYL 0.9 PNY

$9, DYL *33 JSSJS 03 PSPRY 0.9 PNY

1400x1050 1400x1050 1400x1050

1600x1200 1680x1050 1680x1050

0ESV 0ESV 0ESV 0ESV 0ESV 0ESV

$9, DYL *33 JSSJS 03 PSPRY 0.9

03 PSPRY *33 JSSJS $9, DYL 0.9

$$& DDF $9, DYL 0DWURVND PNYPND 'LY; GLY[

3URL]YHGHQRSRGOLFHQFLMRP'76/LFHQVLQJ/LPLWHG

3URL]YHGHQRSRGOLFHQFLMRP'76/LFHQVLQJ/LPLWHG

3URL]YHGHQRSRGOLFHQFLMRP'76/LFHQVLQJ/LPLWHG

3&DXGLRNDEHORP]DDXGLRYH]X_=D

DNWLYLUDQMH 3&<3E3U ]YXND WUHEDWH

NRULVWLWLERþQL$9XOD]V<3E3U3&DXGLR NDEHORP]DDXGLRYH]XNRULVWHüLSULWRPH &59(1( L %,-(/( XOD]H SULNOMXþQRJ NDEHOD]DERþQL$9XOD]_$NRMHYDQMVNL XUHÿDM VSRMHQ SUHNR 6&$57 XWLþQLFH

WHOHYL]RU VH DXWRPDWVNL SUHEDFXMH X $9

/DJDQR SRGLJQLWH SRNORSDF 8PHWQLWH GYLMH AAA

.RPSDWLELOQRVW$9L+'0,6LJQDOD

$9, DYL *33 JSSJS 03 PSPRY 0.9

03 PSPRY *33 JSSJS $9, DYL 0.9 PNY

$$& DDF $9, DYL 0DWURVND PNYPND 'LY; GLY[

*33 JSSJS 03 PSPRYPD 03(*SULMHQRVQL

WRNSRGDWDND WVWUSWS 03(*SURJUDPVNLWRNSRGDWDND

WVWUSWS 03(*SURJUDPVNLWRNSRGDWDND '$792%

MH EH]EHGDQ SRG UD]XPQR

1HPRMWH JXWDWL EDWHULMX RSDVQRVW RG KHPLMVNLK

SRWUHEQDMHRSãWDGR]YROD

LOLYDGLWH&,PRGXOVDPRNDGDMHWHOHYL]RU

3RQRYR SULWLVQLWH 5HSURGXNXM GD ELVWH JOHGDOL

.RPSDWLELOQRVW$9L+'0,6LJQDOD

$9, DYL *33 JSSJS 03 PSPRY 0.9

03 PSPRY *33 JSSJS $9, DYL 0.9

.ODVD/DVHUVNLSURL]YRG

O M X G L X N O M X þ X M X ü L G M H F X V D I L ] L þ N L P L O L

NRPSDQLMH +'0, /LFHQVLQJ $GPLQLVWUDWRU LQF X

WUHQXWQLVWDWXVQMLKRYHQDFLRQDOQHUHJXODWLYH]D/$1QD

6PDUW&HQWHU ]DYLVQRRGPRGHOD

$9, DYL *33 JSSJS 03 PSPRY 0.9

03 PSPRY *33 JSSJS $9, DYL 0.9

PSPRY *33 JSSJS $9, DYL 0.9

03 PSPRY *33 JSSJS $9, DYL 0.9

+(9& VP8 3RNUHWQL-3(*