VALBERG CYCLOMAX-01 - CYCLOMAX-01 - Vacuum Cleaner

CYCLOMAX-01 - CYCLOMAX-01 - Vacuum Cleaner VALBERG - Free user manual and instructions

Find the device manual for free CYCLOMAX-01 - CYCLOMAX-01 VALBERG in PDF.

📄 34 pages English EN ⬇ Download 💬 AI Question ❓ 15 questions ⚙️ Specs
Notice VALBERG CYCLOMAX-01 - CYCLOMAX-01 - page 15
15 / 34
View the manual : Français FR English EN Español ES Nederlands NL
Pick your language and provide your email: we'll send you a specifically translated version.
Product type Bagless canister vacuum cleaner
Brand VALBERG
Model CYCLOMAX-01
Reference 970400
Maximum power 700 W
Suction power 130 W
Vacuum pressure 13 kPa
Dust tank capacity 1.4 L
Noise level 79 dB(A)
Supply voltage 220-240 V ~
Frequency 50/60 Hz
Protection class II
Filter type Washable HEPA filter
Included accessories Floor brush, mini turbo brush, crevice tool
Electronic power adjustment Yes (+/- buttons)
Cord rewinder Yes
Intended use Household use only
Maintenance Regular cleaning of dust compartment and filters
Spare parts Replacement HEPA filter

Frequently Asked Questions - CYCLOMAX-01 - CYCLOMAX-01 VALBERG

How to empty the dust compartment?
Press the two dust compartment release buttons together and remove the compartment. Unscrew the lid, remove the filter, then unscrew the base to empty the dust into a trash can. Clean with a dry cloth.
How to clean the HEPA filter?
The HEPA filter is located in the air outlet. Press the push button to open the flap, then remove the filter. It can be cleaned under running water. Let it dry completely before replacing it.
What to do if suction weakens?
Check that the dust compartment is not full. Clean the HEPA filter and the central filter. Make sure the accessories are not blocked. If the problem persists, the filter may be damaged and must be replaced.
How to use the floor brush on carpet?
The floor brush has a pedal. Press it to retract the brush when vacuuming on carpet, and to extend it on hard floors.
How to adjust the suction power?
Use the Plus and Minus buttons on the vacuum cleaner body to increase or decrease the suction power as needed.
What to do if the power cord does not retract?
Make sure the cord is not twisted and is straightened. Press the cord rewinder button. If the problem persists, check that you have not exceeded the red mark (pulled too far).
How to clean the mini turbo brush?
Disconnect the brush from the tube, remove the locking system, lift the transparent cover, then remove the roller. Clean the bristles with a dry cloth or water, let dry, then reassemble.
Where to store the vacuum cleaner?
Unplug the appliance. Store it in a cool, dry and clean place, out of reach of children. Use the storage slot at the back to attach the floor brush.
The vacuum cleaner does not start, what to do?
Check that the plug is properly connected to a power outlet. Press the On/Off button. If the appliance still does not turn on, contact a qualified technician.
Can I use the vacuum cleaner to vacuum water?
No, this vacuum cleaner is designed only for vacuuming dry waste. Never vacuum liquids or damp materials, as this would damage the appliance and present an electrical risk.

User questions about CYCLOMAX-01 - CYCLOMAX-01 VALBERG

5 questions about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

How to properly close and clip the dust compartment lid of the VALBERG CYCLOMAX-01?
Frequently Asked Questions - 11 j
Response Notice-Facile

The dust compartment lid of the VALBERG CYCLOMAX-01 uses a button and clipping locking system. Here’s how to close it correctly:

  • Align the compartment - Position the dust compartment so that the two unlocking buttons are facing you and can easily fit into the grooves.
  • Press firmly - Press both unlocking buttons of the dust compartment firmly at the same time to bring them closer together and engage the clipping.
  • Wait for the click - Continue pressing until you hear a distinct locking click. This sound confirms that the lid is properly closed and secured.
  • Check the closure - Once you hear the click, gently try to lift or shake the compartment to ensure it doesn’t move. If it holds firmly, the closure is correct.

The secret is to press firmly and simultaneously on both buttons until the click. Many users underestimate the pressure needed - don’t be afraid to press hard.

Respond (be the first)
How to properly clip and secure the brush to the tube of the VALBERG CYCLOMAX-01?
Frequently Asked Questions - 17 j
Response Notice-Facile

If you are having trouble clipping the brush to the tube of the VALBERG CYCLOMAX-01, it is important to check that you are using the correct assembly technique. Here’s how to proceed:

Steps to properly secure the brush to the tube

  • First, check your setup: The VALBERG CYCLOMAX-01 offers two tube options - the flexible tube and the metal tube. Make sure that the brush you are trying to attach is compatible with the one you have in hand.
  • Correctly align the brush: Before clipping, precisely align the brush with the end of the tube (metal or flexible depending on your choice).
  • Insert and press firmly: Push the brush into the tube with constant and firm pressure. The clipping mechanism will automatically lock when it is fully engaged.
  • Check the clipping: Gently pull on the brush to ensure that it is securely locked and does not slip.

Practical tip: If clipping remains difficult, check that the metal tube is correctly inserted into the flexible tube (as indicated in the manual), as this can affect the alignment of the brush's attachment points.

Respond (be the first)
Is the filter of the VALBERG CYCLOMAX-01 washable and how should it be maintained?
Frequently Asked Questions - 27/01/2026
Response Notice-Facile

Yes, the filter of the VALBERG CYCLOMAX-01 is washable, which helps to extend the lifespan of the device and ensure optimal performance.

Maintenance of the washable filter:

  • Removal: Carefully remove the filter from the device according to the provided instructions.
  • Cleaning: Rinse the filter with lukewarm water to remove dust and impurities. Avoid using harsh chemicals that could damage it.
  • Drying: Allow the filter to dry completely in the open air before reinserting it. Do not reinsert it while damp to avoid any risk of mold or malfunction.
  • Frequency: Clean the filter regularly, depending on the usage of the device, to maintain good filtration quality.

Regular maintenance of the filter ensures optimal efficiency and contributes to the longevity of your VALBERG CYCLOMAX-01 device.

Respond (be the first)
How to check and replace the power cord of the VALBERG CYCLOMAX-01?
Frequently Asked Questions - 27/11/2025
Response Notice-Facile

The power cord of your VALBERG CYCLOMAX-01 is a critical component for the safety of the device. While visual inspection is straightforward, replacing the cord should be entrusted to a qualified professional.

Checking the condition of the cord:

  • Always unplug the device from the electrical outlet before any inspection.
  • Visually examine the cord along its entire length for signs of wear: cuts, cracks, abrasions, flattened or discolored areas.
  • Ensure that the insulating sheath (outer covering) is not damaged and that no wires are exposed.
  • Also inspect the plug to see if it shows signs of damage, burning, or melting.
  • Test the cord by bending it slightly at different points: if you feel a stiff or crackling area, or notice a loss of insulation, the cord is damaged.

Risks associated with a damaged cord:

  • Risk of severe or fatal electric shock, especially in humid conditions.
  • Risk of fire or electric shock to the device.
  • Never use a vacuum cleaner with a defective cord, even partially.

Replacing the cord: Replacing the power cord of the VALBERG CYCLOMAX-01 is an electrical intervention that requires specific technical skills. It should never be performed by a domestic user. If you need to replace the cord, contact the VALBERG/ELECTRO DEPOT customer service or a qualified appliance technician. Provide them with the electrical specifications of your device (220-240 V ~, 50/60 Hz, Class II) to ensure compatibility.

Safe use of the cord: When in use, remember that the cord can be stretched up to the visible yellow mark on it. If you see the red mark, it means the cord is excessively taut and should be released immediately to avoid damage. Use the cord reel button (located at the back of the device) to store the cord after use.

Respond (be the first)
How do I remove the wheel from the VALBERG CYCLOMAX-01?
Frequently Asked Questions - 27/11/2025
Response Notice-Facile

The VALBERG CYCLOMAX-01 does not have any mobility wheels. If you want to remove the roller wheel from the mini turbo brush, follow these exact steps from the manual:

Preparation: First, unplug the device from the power outlet and ensure it is turned off.

Accessing the roller: Detach the mini turbo brush from the tube by twisting and pulling it. Then remove the locking system of the brush. Lift the transparent cover to access the roller.

Removing the roller: Gently remove the roller before completely taking out the brush. This roller can be easily cleaned under running water to remove accumulated hair and dust.

Cleaning and drying: Clean the bristles of the brush and the roller under running water. Allow all parts to dry completely before reassembling.

Reassembly: Reinstall the roller into the mini turbo brush, then close the locking system. Reinsert the brush into the tube until you hear a click. The CYCLOMAX-01 has no other wheel to disassemble: the floor brushes simply detach by twisting and pulling.

Respond (be the first)

Download the instructions for your Vacuum Cleaner in PDF format for free! Find your manual CYCLOMAX-01 - CYCLOMAX-01 - VALBERG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CYCLOMAX-01 - CYCLOMAX-01 by VALBERG.

USER MANUAL CYCLOMAX-01 - CYCLOMAX-01 VALBERG

Thank you for choosing this VALBERG product. VALBERG products are chosen, tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a top-quality, easy-to-use product that won't let you down. We're confident your new device will be a pleasure to use every day!

Welcome to ELECTRO DEPOT.

Table of Contents

VALBERG CYCLOMAX-01 - CYCLOMAX-01 - Table of Contents - 1

Parts

Product overview

Intended use

Specifications

VALBERG CYCLOMAX-01 - CYCLOMAX-01 - Table of Contents - 2

Assembly/Disassembly

Operation

VALBERG CYCLOMAX-01 - CYCLOMAX-01 - Table of Contents - 3

Cleaning and maintenance

Troubleshooting

Storage

Parts

Dust cup release button
B Handle
C Power cable rewind button
+/- buttons to increase or decrease the suction.
E ON/OFF button
F Air vent
Floor brush storage slot
Dust cup

Hose-connecting inlet
J Flexible hose
Metal extension tube (telescopic)
Floor brush (smooth floors and carpets)
M Pedal (to extend and retract the brush)
Long crevice tool (for hard-to-reach places)
Mini turbo brush (to remove
0 stubborn dirt from furniture, smooth floors and carpets]

Product overview

  • Unpack and remove all labels from the unit. Please check that all of the unit's parts are included and intact. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.
  • Keep all packaging out of the reach of children. There is a risk of accidents if children play with packaging materials.

Intended use

This vacuum cleaner is for household use only. It has not been designed for industrial or professional use by cleaning companies.
Any other use may damage the unit or cause injury.

Specifications

Model:970400 - CYCLOMAX
Vacuum cleaner
Power:700 W max.
Dust cup capacity:1.4 L
Noise level:79 dB
Suction power:130 W
Pressure:13 kPa
Operating voltage:220-240 V ~, 50/60 Hz
Protection class:Class II

Assembly/Disassembly

To assemble

1 Connect the dust cup lid to the unit's body by pushing until it clicks into place.
Insert the flexible hose into the hose-connecting inlet on the unit's body until it clicks into place.
3 Insert the metal tube into the flexible hose.
To adjust the length of the metal tube, push the pushbutton backwards and extend the tube.
5 Attach one of the following accessories by inserting it into the metal tube or flexible hose.

  • Floor brush for various types of flooring.
  • Press the pedal to retract the brush (for carpets) or extend it (for smooth floors).
  • Mini turbo brush for furniture.
  • Long crevice tool for hard-to-reach places.

Insert the plug into the mains socket.

  • The power cable can be extended up to the yellow mark. If the red mark is visible, then you have pulled the cable out too far.

To disassemble

  • Make sure the unit is turned off and disconnect the plug from the mains socket.
  • Detach the brushes, crevice tool and metal tube by twisting to pull them apart.

To remove the flexible hose, press the hose release button and pull out the hose.
Press the cable rewind button to store the cable away.
8 Insert the floor brush into the back of the unit for easy storage.

Operation

  • Once the unit is assembled and plugged in, it is ready for use.

9 Press the ON/OFF button to turn the unit on or off.
10 Press the + or - button to increase or decrease the level of suction.
11 Use the handle to carry the vacuum.

Cleaning and maintenance

VALBERG CYCLOMAX-01 - CYCLOMAX-01 - Cleaning and maintenance - 1

WARNING!

  • Always unplug the USB connector from the power supply before cleaning.

  • Never immerse the unit in water or any other liquid.

  • Detach all accessories from the main unit.

  • Remove any blockages from the accessories.
  • Clean the unit with a soft, slightly damp cloth. Make sure that no liquid enters the unit.
  • When cleaning the unit, never use abrasive products, metal brushes, scourers, wire sponges or sharp utensils.
  • After cleaning, dry the unit thoroughly.

Cleaning the dust cup and filters

  • Empty the dust cup whenever it is full or there is a loss of suction.

Press the two dust cup release buttons to attach or detach the cup.
13 ① Detach the dust cup lid.
(2) Remove the filter.
14 Remove the central part of the filter over a bin.
15 Detach the base of the dust cup to empty the contents.

  • Wipe the dust cup and the central part of the filter with a dry cloth.
  • The filter can be cleaned under running water.

Cleaning the air outlet filter

16 ① Press the air outlet pushbutton to open it.
(2) Press the pushbutton to remove the HEPA filter.

  • The HEPA filter can be cleaned under running water.
  • Let all the parts dry.

VALBERG CYCLOMAX-01 - CYCLOMAX-01 - Cleaning the air outlet filter - 1

WARNING!

  • To avoid damaging the unit, only use and insert dry filters!

  • Reassemble all the parts in reverse order.

Disassembling and cleaning the brushes

Floor brush:

17 Detach the brush from the tube.

Mini turbo brush:

18 ① Detach the brush from the tube and remove the locking system.

(2) Lift up the transparent cover.
③ Remove the roller and gently pull the brush out.

  • Clean the brush bristles. Let them dry completely.
  • Reposition the brush and re-attach the locking system.

Troubleshooting

ProblemPossible CauseSolution
The unit does not work.·The unit is not connected to the mains socket.·Securely insert the plug into the mains socket. Press the Power button. If the unit is still not working, get it checked by a qualified technician.
·The dust cup is full.·Empty the dust cup.
The suction power is weak, there is no suction or the motor vibrates.·The nozzle is blocked.·Remove the blockage.
·The filter is blocked, dirty or broken.·Clean the filter. ·If necessary, replace the filter with a new one.

Storage

  • Always unplug the unit before storing it.
  • Store the unit in a fresh, dry and dust-free place, out of the reach of children and pets.
  • Please retain the packaging and use it to store your unit when it is not in use for an extended period of time.

Bedankt!

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : VALBERG

Model : CYCLOMAX-01 - CYCLOMAX-01

Category : Vacuum Cleaner