TEG-S16DG - Ethernet Switch TRENDNET - Free user manual and instructions

Product Type	Unmanaged Gigabit Ethernet Switch
Model	TEG-S16DG
Brand	TRENDNET
Number of Ports	16 RJ-45 10/100/1000 Mbps Auto-MDIX Ports
Supported Speeds	10/20 Mbps (half/full-duplex), 100/200 Mbps (half/full-duplex), 2000 Mbps (full-duplex)
Network Standards	IEEE 802.3 10Base-T, 802.3u 100Base-TX, 802.3ab 1000Base-T, 802.3x Flow Control
Switching Capacity	32 Gbps
Buffer Memory	2 Mbit
Filtering Table	8,000 entries
Jumbo Frame Support	Up to 9,216 bytes
Power Supply	100-240 VAC, 50/60 Hz, universal internal switching power supply
Max Power Consumption	7.2 watts
Dimensions (W x D x H)	440 x 140 x 45 mm
Weight	1.6 kg
LED Indicators	Power, 10M/LINK/ACT, 100M/1000M
Fan Type	Built-in fan (active cooling)
Mounting	19-inch rack mount (kit included)
Operating Temperature	0° to 40°C
Operating Humidity	Max. 90% (non-condensing)
Certifications	CE, FCC
Maintenance and Cleaning	Unplug the device before cleaning. Use a soft, dry cloth. Do not use chemical or abrasive products.
Safety	Do not expose to water or moisture. Ensure adequate ventilation. Do not place heavy objects on it.
Spare Parts and Repairability	This device contains no user-serviceable parts. In case of failure, contact TRENDNET support.

Frequently Asked Questions - TEG-S16DG TRENDNET

How to install the TEG-S16DG switch?

Unpack the switch and power cord. Place it on a flat surface or mount it in a rack using the provided kit. Plug the power cord into a nearby electrical outlet (max 1.8 m). Connect your devices via Cat.5e or higher Ethernet cables. The switch is ready to use, no configuration is needed.

What do the LEDs on the front panel mean?

The Power LED indicates power on. For each port, the 10M/LINK/ACT LED is solid green when a device is connected, blinking during activity, off otherwise. The 100M/1000M LED is green for a 2000 Mbps (Gigabit full-duplex) link, amber for 100/200 Mbps, off for 10/20 Mbps or no link.

Which cables to use for optimal performance?

For 10/100 Mbps, use Cat.5 cable. For Gigabit (1000 Mbps), use Cat.5e or Cat.6. The maximum segment length is 100 meters.

Does the switch support VLAN?

No, the TEG-S16DG is an unmanaged switch. It does not allow VLAN configuration or other management features. It simply switches packets based on MAC addresses.

How to reduce power consumption?

This switch incorporates GREENnet technology which detects cable length and automatically reduces power consumption on inactive or underutilized ports. No manual action is required.

Can I connect different types of cables (straight/crossover)?

Yes, all ports have Auto-MDIX function. They automatically detect the cable type (straight or crossover) and adjust. You can use any standard Ethernet cable.

What to do if the switch does not power on?

Check that the power cord is properly plugged in and the outlet works. Test with another cord if possible. If the Power LED remains off, contact TRENDNET support.

Is this switch compatible with PoE standard?

No, the TEG-S16DG is not a PoE switch. It does not provide power over Ethernet cables. For PoE devices, use an injector or a dedicated PoE switch.

How to mount the switch in a rack?

Use the provided mounting kit. Attach the brackets to each side of the switch using the included screws. Position the switch in the rack and screw the brackets to the rack rails. Ensure the switch is well supported (max weight 1.6 kg).

Where to find the latest firmware version?

This unmanaged switch does not require firmware updates. However, for technical information, visit the official TRENDNET website (www.trendnet.com) and search for model TEG-S16DG.

USER MANUAL TEG-S16DG TRENDNET

Technical Specifications 4

Troubleshooting 5

100/200Mbps (Half/Full)

1. After connecting the Switch to a power outlet, the LEDs do not turn on.

2. Check the connection of the power cord to the TEG-S16g/TEG-S24g and the power outlet.

3. Check that the power outlet is receiving power.

4. When I connect a computer to one of the ports on the Switch, the 10M/LINK/ACT LED turns on, but I am not getting Gigabit speeds.

5. Check the LEDs. If the 100M/1000M LED is green, the computer's connection speed is 1000Mbps. If the 100M/1000M LED is amber, the computer's connection speed is 100Mbps. If the 100M/1000M LED is off, the computer's connection speed is 10Mbps.

6. Check the Ethernet Cable. Make sure you are using CAT-5e or CAT-6 Ethernet Cables. Some CAT-5 cables are not rated to run in Gigabit.

7. Make sure that you have a Gigabit Ethernet Adapter installed on your computer.

8. After I connect my PCs to the Switch, I am unable to share files.

9. Check the LEDs on the Switch. Make sure the 10M/LINK/ACT LED is on.

10. Check the network cable. The minimum length of the cable is 1.5 meters and the maximum length of the cable is 100 meters.
11. Disable any software firewall program.

12. Verify that you have file sharing enabled. Please contact your Operating System support for more information.

13. After I connect my PCs to the Switch, I can only get onto the Internet from one computer.

The Switch was not designed to share Internet between multiple computers. You need to get an Internet router such as the TEW-652BRP.

1. Where is the uplink port located on the Switch?

Since all the ports on the Switch are Auto-MDIX, any of the ports can be used as an uplink port.

If you still encounter problems or have any questions regarding the

TEG-S16g/TEG-S24g please contact TRENDnet's Technical Support Department.

Limited Warranty

TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.

TEG-S16g/TEG-S24g - 3 Years Limited Warranty

AC/DC Power Adapter, Cooling Fan and Power Supply carry a 1 year limited warranty

If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. All products that are replaced become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies.

TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty.

There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual.

Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees.

WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDNET'S OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTY AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTYES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTYES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF TRENDNET'S PRODUCTS.

TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALGEGD DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCULES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ASING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

Governing Law: This Limited Warranty shall be governed by the laws of the state of California.

Some TRENDnet products include software code written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL").

Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license.

PWP05202009v2

Detalls standard applicable:

EN 55022:2006 +A1:2007 Class A

EN 61000-3-2:2006

EN 61000-3-3 : 2008

Director of Technology

Position / Title

Signature

Certifications

This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may cause undesired operation.

Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

ADVERTENCIA

Product Warranty Registration

Please take a moment to register your product online. Go to TRENDnet's website at http://www.trendnet.com/register