VH-120 - VHF wireless system GEMINI - Free user manual and instructions

USER MANUAL VH-120 GEMINI

Parts of the design of this product may be protected by worldwide patents.

Information in this manual is subject to change without notice and does not represent a commitment on the part of the vendor. Gemini Sound Products shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual.

No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording, for any purpose without the express written permission of Gemini Sound Products.

It is recommended that all maintenance and service on the product should be carried out by Gemini Sound Products or it's authorized agents. Gemini Sound Products cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorized personnel.

In the U.S.A., if you have any problems with this unit, call 1-732-738-9003 for customer service. Do not return equipment to your dealer.

Worldwide Headquarters • 120 Clover Place, Edison, NJ 08818 • USA
Tel: [phone] • Fax: [phone]

France • G.S.L. France • 11, Avenue Leon Harmel, Z.I. Antony, 92160 Antony, France
Tel [phone] • Fax [phone]

Germany • Gemini Sound Products GmbH • Ottosrasse 6, 85757 Karlsfeld, Germany
Tel: 08131 - 39171-0 • Fax: 08131 - 39171-9

UK • Gemini Sound Products • Unit C4 Hazleton Industrial Estate, Waterlooville, UK P08 9JU Tel: [phone] • Fax: [phone]

Spain • Gemini Sound Products S.A. • Mino, 112, Nave 1, 08223 Terrassa, Barcelona, Spain
Tel: [phone] • Fax: [phone]

gemini

Owners Manual

VH Series

VH-101 Single Channel

VH-120 Dual Channel

VHF Wireless System

INTRODUCTION

Congratulations on purchasing a Gemini wireless system. This state of the art unit includes the latest features backed by a three year limited warranty. Prior to use, we suggest that you carefully read all the instructions. This book includes instructions for both the VH-101 and the VH-120 systems.

CAUTIONS

1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. Dust, dirt and debris can interfere with the performance of this unit. Make an effort to keep the unit away from dusty, dirty environments, and cover the unit when it is not in use. Dust it regularly with a soft, clean brush.
5. When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.

FCC RULES AND REGULATIONS

Gemini wireless systems are the type accepted under FCC rules parts 74 and 15. Licensing of Gemini equipment is the user's responsibility and licensability depends on the user's classification and application.

NOTE

This equipment has been tested and found to comply with the limits set forth under part 15 and 74 of FCC rules. This equipment operates at a frequency that has been authorized by the FCC. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, try one or more of the following suggestions:

1. Repoint or relocate the receiving antenna.
2. Plug the equipment into a socket on a different circuit.
3. Call your dealer to arrange to exchange the unit for one with a different frequency.

Remember, any changes made to the unit without authorization from Gemini will void your warranty.

The VH-101 single channel VH series wireless system is a high quality audio product that provides excellent performance under most operating conditions.

Four different models are available and all operate on a VHF high band frequency between 174.60 MHz to 204.60 MHz.

THE MODELS AVAILABLE ARE:

VH-101M - which comes equipped with a hand held microphone transmitter.

VH-101L - which comes equipped with a belt pack and lavalier transmitter.

VH-101H - which comes equipped with a belt pack and a headset transmitter.

ALL MODELS ARE AVAILABLE IN SIX DIFFERENT FREQUENCIES:

Frequency Conversion Chart:

Channel	Frequency
1	174.60 MHz
2	177.60 MHz
3	180.60 MHz
4	186.60 MHz
5	192.60 MHz
6	198.60 MHz
7	201.60 MHz
8	204.60 MHz

Note: Effective range between the transmitter and receiver is up to 150 feet.

1. Remove all packing materials. Save the box and packing material to transport the unit, and in case the unit ever requires service.
2. Plug the AC adaptor into the rear of the receiver where the jack is labeled DC 12V. Then plug the adaptor into an appropriate AC outlet. Switch the power to the ON position. Note: The adaptor is available in 120V AC or 230V AC.
3. Extend the antenna fully vertical and point it toward the direction you will be speaking from.
4. Insert the 1/4" phone cable into the jack labeled AUDIO OUT on the rear of the receiver, and connect the other end of the cable to your amp, effects or mixer mic jack.

5. Adjust the volume using the level control on the front panel.

6. To adjust the squelch, place the small plastic tool (included with the unit) in the hole marked SQUELCH at the back of the unit, and slowly turn the tool to adjust the output level to just above the level of background noise. Setting the squelch too high will reduce the range of the system. Setting the squelch too low will increase the level of unwanted noise.

VH-120 DUAL CHANNEL WIRELESS SYSTEM

The VH-120 dual channel VH series wireless system is two separate single channel transmitters of different frequencies transmitting to one unit that houses both frequency receivers. One output carries both frequency signals to your mixer simultaneously through one cable.

Four different models are available and all operate on a VHF high band frequency between 174.60 MHz to 204.60 MHz.

THE MODELS AVAILABLE ARE:

VH-120M - which comes equipped with two hand held microphone transmitters.
VH-120L - which comes equipped with two belt packs and two lavalier transmitters.
VH-120H - which comes equipped with two belt packs and two headset transmitters.

ALL MODELS ARE AVAILABLE IN THREE SETS OF DIFFERENT FREQUENCIES:

Frequency Conversion Chart:

System	Channels	Frequencies
1	1 & 5	174.60 MHZ/192.60 MHZ
2	2 & 6	177.60 MHZ/198.60 MHZ
3	3 & 7	180.60 MHZ/201.60 MHZ
4	4 & 8	186.60 MHZ/204.60 MHZ

Note: Effective range between the transmitter and receiver is up to 150 feet each side.

1. Remove all packing materials. Save the box and packing material to transport the unit, and in case the unit ever requires service.
2. Plug the AC adaptor into the rear of the receiver where the jack is labeled DC 12V. Then plug the adaptor into an appropriate AC outlet. Switch the power to the ON position. Note: The adaptor is available in 120V AC or 230V AC.
3. Extend the antennas fully vertical and point them toward the direction you will be speaking from.
4. Insert the 1/4" phone cable into the jack labeled AUDIO OUT on the rear of the receiver, and connect the other end of the cable to your amp, effects or mixer mic jack.
5. Adjust the volume using the level controls on the front panel.
6. To adjust the squelch, place the small plastic tool (included with the unit) in the hole marked SQUELCH at the back of the unit, and slowly turn the tool to adjust the output level to just above the level of background noise. Setting the squelch too high will reduce the range of the system. Setting the squelch too low will increase the level of unwanted noise.

HAND HELD TRANSMITTER FEATURES

High sensitivity cardiod capsule for professional use
- Special noise absorption parts inside the barrels eliminating switch shock and handling noise
Frequency with quartz locked control

CAUTIONS

1. Do not drop the microphone onto a hard surface.
2. Do not strike the microphone head front with fist or fingers, and do not blow strongly into the microphone head front.
3. Do not use the microphone in areas of high humidity and/or high temperature as this could lead to damage of the microphone.

1. Open the battery holder by turning it counterclockwise. Insert a 9V battery into the battery holder according to the polarity indication marked on the battery housing. Close the battery holder.
2. Push the power switch to the ON position. The BATT indicator should flash once briefly as you turn on the mic indicating that the mic has sufficient power. If the BATT stays on, it indicates that the battery has insufficient power and should be changed. If the BATT does not light at all and the mic does not work, it indicates that the battery is dead, and you should change the battery. If the microphone is not going to be used for any length of time, push the power switch to OFF and remove the battery. Do not switch the mic on and off rapidly, because you won't get a true indication from the BATT indicator.

LAVALIER BELT PACK TRANSMITTER FEATURES

Heavy duty strain relief
Foam wind screen
- Tie clip

1. Open the battery door by sliding towards the arrow. Insert a 9V battery into the battery holder according to the polarity indication marked on the battery housing. Close the battery door.
2. Push the power switch to the ON position. The LOW BATT indicator should flash once as the switch passes MUTE indicating that the transmitter has sufficient power. If the LOW BATT stays on, it indicates that the battery has insufficient power and should be changed. If the LOW BATT does not light at all, it indicates that the battery is either dead or not positioned correctly, and you should correct the positioning or change the battery. If the microphone is not going to be used for any length of time, push the power switch to OFF and remove the battery.
3. The lavalier mic clip should be placed as high as possible in a vertical line with your mouth.
4. To adjust the gain (input sensitivity), remove the battery door and place the small plastic tool (included with the unit) in the hole marked mic adj and slowly turn the tool and speak into the mic until the volume is adjusted. Use of any other tool to adjust the gain will void the warranty.
5. The lavalier wire is the transmit antenna. Do not roll up, coil or shorten during use. This wire must be kept as straight as possible.

HEADSET BELT PACK TRANSMITTER FEATURES

Heavy duty strain relief
- Headset
Cable

1. Open the battery door by sliding towards the arrow. Insert a 9V battery into the battery holder according to the polarity indication marked on the battery housing. Close the battery door.
2. Push the power switch to the ON position. The LOW BATT indicator should flash once as the switch passes MUTE indicating that the transmitter has sufficient power. If the LOW BATT stays on, it indicates that the battery has insufficient power and should be changed. If the LOW BATT does not light at all, it indicates that the battery is either dead or not positioned correctly, and you should correct the positioning or change the battery. If the unit is not going to be used for any length of time, push the power switch to OFF and remove the battery.
3. To adjust the gain (input sensitivity), remove the battery door and place the small plastic tool (included with the unit) in the hole marked mic adj and slowly turn the tool and speak into the mic until the volume is adjusted. Use of any other tool to adjust the gain will void the warranty.

SPECIFICATIONS

RECEIVER (VH-101 AND VH-120):

Signal to Noise Ratio. Greater than 60 dB

Modulation Mode.. FM

IF Frequency. 10.7 MHz

AF Response. .50 Hz to 20KHz, 1 kHz (±3 dB)

T.H.D. Less than 1%

Power Supply. D.C. 12 Volts 500 max

Dimensions (VH-101) 37 x 160 x 135 mm

Dimensions (VH-120) 37 x 270 x 135 mm

TRANSMITTER (ALL MODELS):

RF Power Output. .50 mW Max.
Spurious Emission. >55 dBuV
Frequency Stability. ±0.005% with quartz control
AF Response. .50 Hz to 20KHz, 1 kHz (±3 dB)
Battery Type. 9 Volt Alkaline
Battery Life. 6-8 hours

TRANSMITTER (HAND HELD):

Microphone Element. Unidirectional Condenser Mic

Dimensions. 62 x 245 mm

TRANSMITTER (LAVALIER):

Microphone ElementCondenser Mic

Dimensions. 87 x 63 x 23 mm

TRANSMITTER (HEADSET):

Microphone ElementCondenser Mic

Polar Pattern. Cardiod

Dimensions. 87 x 63 x 23 mm

EINFUHRUNG

TRANSMISOR (MANUAL):

Dimensions. 87 x 63 x 23.5 mm

INTRODUZIONE