TA-T19 (cage Sony A7C) - Camera accessory Tilta - Free user manual and instructions

USER MANUAL TA-T19 (cage Sony A7C) Tilta

[全笼解说]

将手柄对准到笼子侧臂的1/4定位孔上。

对应后拧紧螺丝即可完成装配。

[安装快装板/底座]

Each of the following accessories can be attached to and used with the cage.

No.	PRODUCT NAME	SKU
CECM01	Full Camera Cage for Sony A7C	TA-T19-FCC
CECM02	Tiltaing Lightweight Quick Release Top Handle	TA-QRTH3
CECM03	15mm Bottom Single Rod Holder	TA-BSRA-15
CECM04	EF Mount Lens Adapter Support for Sony A7C	TA-T19-LAS
CECM05	15mm Side Single Rod Holder	TA-SRA-15
CECM06	Manfrotto Quick Release Plate for Sony A7C	TA-T19-QRBP1
CECM07	15mm LWS Baseplate	TA-T08-BSP
CECM08	Tiltaing Advanced Side Handle Attachment Type VII	TA-AHA7-LR
CECM09	Tiltaing Left Side Advanced Focus Handle (F570 Battery)	TA-LFH-57
CECM10	Tiltaing Left Side Wooden Handle	TA-LWH
CECM11	Tiltaing Cold Shoe Receiver Attachment	TA-CSR-GD

TOP

BOTTOM

RIGHT SIDE

LEFT SIDE

1 Mounting hole for 15mm bottom single rod holder
2 Lens adapter support screw hole
3 Mounting hole for 15mm side single rod holder
4 Right side wrist strap holder
5 1/4"-20 screw hole (for installing NATO rail and side handle.)
6 Left side strap holder
7 1/4"-20 screw holes with locating points (for HDMI clamp attachment.)
8 1/4"-20 screw hole

9 Cold shoe mount (for installing top handle.)
10 Cold shoe mount (for installing microphone, additional light, etc.)
11 1/4"-20 screw hole
12 1/4"-20 screw hole (for installing Manfrotto and ARCA plate.)
13 Camera security screw hole
14 1/4"-20 screw hole (for installing Manfrotto and ARCA plate.)
15 ARCA standard 38mm mount (can mount onto RS 2 directly.)

INSTALLING THE CAGE

ASSEMBLY

1. Take out the 1/4"-20 screw from the bottom of the cage. Place the Sony A7C in the camera cage.
2. Insert the 1/4"-20 screw into the screw hole and tighten the screw.

INSTALLING TOP HANDLE

Quick Release Top Handle

(OPTIONAL)

1. Slide the top handle into the cold shoe mount on top of the cage.
2. Tighten the tie down screw.

INSTALLING SIDE HANDLE & SIDE HANDLE ATTACHMENT

To install the side handle attachment, align the M3 screw holes on the focus handle with the left side handle attachment. Tighten the screws.

The focus handle has USB-C 8v and DC 12v outputs. Please check and connect your equipment accordingly. Tiltta is not responsible for any user errors.

Align the focus handle with the 1/4"-20 screw hole on the side of the cage.

Align the locating points and tighten the tie down screw.

INSTALLING WOODEN HANDLE & COLD SHOE MOUNT

Align the wooden handle with the 1/4"-20 screw hole on the side of the cage.

Align the locating points and tighten the tie down screw.

Align the cold shoe mount with the 1/4"-20 screw hole on top of the wooden handle.

Tighten the screw.

INSTALLING QUICK RELEASE PLATE & BASEPLATE

Align the 1/4"-20 screw holes on the bottom of the cage with the bottom plate.

Tighten the tie down screws.

Slide the bottom plate onto the baseplate until the safety lock bounces up, then tighten the locking toggle.

TILTA

版权由深圳市铁头科技有限公司所有

需授权方可转载

All copyrights belong to Tilta Technology Co. Ltd.

Written permission is needed for any reproductions.

Tilta has the right to adjust product specification without notice.

All measurements are for reference only. Please see the actual products for more details.

TILTA are registered trademarks owned by Tiltta Technology Co., Ltd.

Website: www.tilta.com

US Address: 2801 W Magnolia Blvd, Burbank, CA 91505

US Contact Number: [phone]

关注微信公众号

扫码进入官网