SWZU - Lawn mower Scag - Free user manual and instructions

USER MANUAL SWZU Scag

THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMATION FOR YOUR SCAG MOWER. READING THIS MANUAL CAN PROVIDE YOU WITH ASSISTANCE IN MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR MOWER PERFORMING TO MAXIMUM EFFICIENCY. THE SPECIFIC MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER. BEFORE OPERATING YOUR MACHINE, PLEASE READ ALL THE INFORMATION ENCLOSED.

OPERA TO R'S MANUAL

WARNING:

FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.

* Keep all shields in place, especially the grass discharge chute.
* Before performing any maintenance or service, stop the machine and remove the spark plug wire and ignition key.
* If a mechanism becomes clogged, stop the engine before cleaning.
* Keep hands, feet and clothing away from power-driven parts.
* Read this manual completely as well as other manuals that came with your mower.
* Keep others off the tractor (only one person at a time)

Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the equipment.

This manual covers the operating instructions and illustrated parts list for:

SWZU36A-15KA	with a serial number of	A2300001 to A2399999
SWZU48A-17KA	with a serial number of	A2500001 to A2599999
SWZU48A-18HN	with a serial number of	A2600001 to A2699999
SWZU52A-17KA	with a serial number of	A2700001 to A2799999
SWZU52A-18HN	with a serial number of	A2800001 to A2899999
SWZU52A-18KH	with a serial number of	A2900001 to A2999999
SWZU52A-19KAI	with a serial number of	A3000001 to A3099999
SWZU-21KAE	with a serial number of	A3600001 to A3699999
SWMU-52A	with a serial number of	A3700001 to A3799999
SWMU-61A	with a serial number of	A3800001 to A3899999

Always use the entire serial number listed on the serial number tag when referring to this product.

SCAG®

POWER EQUIPMENT

TABLE OF CONTENTS

SUBJECT

PAGE

Introduction 1

Direction Reference....1

Servicing the Engine and Drive Train Components 1

Symbols.... 2-3

General Safety Instructions 4

Signal Words 4

Before Operating Considerations 4-6

Operation Considerations 6-7

Maintenance and Storage 7-8

Initial Run-In Procedures 8

Mower Operation 8-9

Belt Tension 10

Cutter Deck Adjustments 10-11

Cutter Blades 11

Custom-Cut Baffle Adjustment 11-12

Neutral Adjustment 12-13

Steering Control Rod Adjustment 13

Tracking Adjustment 13-14

Parking Brake 14

Lubrication and Maintenance Chart 15

Checking Hydraulic Oil Level 16

Changing Hydraulic Oil 16

TABLE OF CONTENTS

(CONTINUED)

SUBJECT

PAGE

Changing Hydraulic Oil Filter Element....16-17

Engine Oil Maintenance 17

Engine Air Cleaner Maintenance .... 17

Checking Electrolyte Level and Cleaning Battery 17

Charging the Battery 18

Jump Starting 18

Cleaning The Machine 18

Troubleshooting Cutting Conditions 19-21

Technical Specifications 22-23

Illustrated Parts List

SWMU-36"A Cutter Deck....24-25

SWMU-48"A, 52"A, & 61"A Cutter Decks 26-27

Cutter Deck Frame 36"....28-29

Cutter Deck Frame 48" & 52" Small Frame 30-31

Cutter Deck Frame 52" & 61" Large Frame 32-33

Engine Deck - Manual Start 34-35

Engine Deck - Electric Start (SWZU-21KAE) 36-37

Drive And Brake Components 38-39

Notes 40

Serial Number Breakdown 41

Handle Assembly - Small Frame (16") - Refer to Serial Breakdown on Page 41 ...... 42-43

Notes 44

Serial Number Breakdown 45

Handle Assembly - Small Frame (16") - Refer to Serial Breakdown on Page 45...... 46-47

Handle Assembly - Large Frame (SWZU-21KAE) 48-49

Hydraulic Assembly 50-51

Hydraulic Pump Assembly 52-53

Engine Deck Wire Harness (Manual Start) 54

Handle Wire Harness (Manual Start) 54

Engine Deck Wire Harness - Kawasaki (Electric Start) 55

Handle Wire Harness - Kawasaki (Electric Start) 55

Wire Harness Adaptor - Honda 56

Wire Harness Adaptor - Kawasaki (15HP, 17HP & 19HP) 56

Replacement Decals 57-58

Warranty Statement ...... Inside Back Cover

GENERAL INFORMATION

INTRODUCTION

Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual.

If additional information or service is needed, contact your Scag Power Equipment Dealer.

We encourage you to contact your dealer for repairs. All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts.

USE OF OTHER THAN ORIGINAL SCAG REPLACEMENT PARTS WILL VOID THE WARRANTY.

For pictorial clarity, some illustrations and figures in this manual may show shields, guards or plates open or removed. Under no circumstances should your mower be operated without these devices in place.

All information is based upon product information available at the time of approval for printing. Scag Power Equipment reserves the right to make changes at any time without notice and without incurring any obligation.

WARNING

FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109

USE ONLY SCAG APPROVED ATTACHMENTS AND ACCESSORIES.

Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine. Using unapproved attachments, (especially "stand-up" riding attachments) may be hazardous.

SCAG APPROVED ATTACHMENTS AND ACCESSORIES:

GC-F4 (p/n 9002)

GC-4D (p/n 9001)

Mulch Plate (p/n 9258, 9259, 9260, 9261)

Hurricane Mulch System™(p/n 9263, 9264, 9265, 9266)

Cup Holder (p/n 9240)

Hour Meter (p/n 48023)

Turbo Baffle (p/n 423955, 423956, 423957)

Blade Buddy (p/n 9212)

Flat-Free Caster Tires (9276)

DIRECTION REFERENCE

The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s right and left when standing in the normal operating position and facing the forward travel direction.

SERVICING THE ENGINE AND DRIVE TRAIN COMPONENTS

The detailed servicing and repair of the engine and hydraulic pumps are not covered in this manual; only routine maintenance and general service instructions are provided. For service of these components during the limited warranty period, it is important to contact your Scag dealer or find a local authorized servicing agent of the component manufacturer. Any unauthorized work done on these components during the warranty period may void your warranty.

ISO Symbols

CE

CE Mark

SYMBOL	DESCRIPTION	SYMBOL	DESCRIPTION
	Choke		Transmission
	Parking Brake		Spinning Blade
	On/Start		Spring Tension on Idler
	Off/Stop		Oil
Falling Hazard
	Fast		Slow
	Continuously Variable - Linear		Cutting Element - Basic Symbol
	Pinch Point		Cutting Element - Engage
[z3c5]	Hourmeter/Elapsed Operating Hours		Cutting Element - Disengage
	Thrown Object HazardKeep Bystanders Away		Read Operator's Manual

SAFETY INFORMATION

GENERAL SAFETY INFORMATION

Your mower is only as safe as the operator.

Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance and storage of the equipment. Make sure every operator is properly trained and thoroughly familiar with all of the controls before operating the mower. The owner/user can prevent and is responsible for accidents or injuries occurring to themselves, other people or property.

READ THIS OPERATOR'S MANUAL BEFORE ATTEMPTING TO START YOUR MOWER.

If the operator(s) or mechanic(s) cannot read English or Spanish, it is the owner's responsibility to explain this material to them.

A replacement manual is available from your authorized Scag Service Dealer or by contacting Scag Power Equipment, Service Department at P.O. Box 152, Mayville, WI 53050 or contact us via the Internet at www.scag.com. The manual for your machine can be downloaded by using the model and serial number or use the contact form to make your request. Please indicate the complete model and serial number of your Scag product when requesting replacement manuals.

SIGNAL WORDS

This symbol means “Attention! Become Alert! Your Safety is Involved!” The symbol is used with the following signal words to attract your attention to safety messages found on the decals on the machine and throughout this manual. The message that follows the symbol contains important information about safety. To avoid injury and possible death, carefully read the message! Be sure to fully understand the causes of possible injury or death.

Signal Word:

The signal word is a distinctive word found on the safety decals on the machine and throughout this manual that alerts the viewer to the existence and relative degree of the hazard.

DANGER:

The signal word “DANGER” denotes that an extremely hazardous situation exists on or near the machine that could result in high probability of death or irreparable injury if proper precautions are not taken.

WARNING:

The signal word “WARNING” denotes that a hazard exists on or near the machine that can result in injury or death if proper precautions are not taken.

CAUTION:

The signal word “CAUTION” is a reminder of safety practices on or near the machine that could result in personal injury if proper precautions are not taken.

Your safety and the safety of others depends significantly upon your knowledge and understanding of all correct operating practices and procedures of this machine.

BEFORE OPERATION CONSIDERATIONS

1. Become familiar with the safe operation of the equipment, operator controls, and safety signs.
2. NEVER allow children or untrained people to operate or service this machine.
3. Clear the area to be mowed of objects that could be picked up and thrown by the cutter blades.

BEFORE OPERATION CONSIDERATIONS (CONT'D)

1. Always wear appropriate clothing, loose fitting clothing, long hair or jewelry could get tangled in moving parts. Do not operate the machine wearing shorts; always wear adequate protective clothing including long pants. Wearing safety glasses, safety shoes and a helmet is advisable and is required by some local ordinances and insurance regulations.
2. Operator hearing protection is recommended, particularly for continuous operation of the mower. Wear suitable hearing protection. Prolonged exposure to loud noise can cause hearing impairment or hearing loss.
3. Keep the machine and attachments in good operating condition. Keep all shields and safety devices in place. If a shield, safety device or decal is defective or damaged, repair or replace it before operating the machine.

WARNING:

This machine is equipped with an interlock system intended to protect the operator and others from injury. This is accomplished by preventing the engine from starting unless the deck drive is disengaged, the parking brake is on, and the speed adjustment lever is in the neutral position. The system shuts off the engine if the operator releases the operator presence levers with the deck drive engaged and/or the speed adjustment lever not in the neutral position, or the parking brake disengaged. Never operate equipment with the interlock system disconnected or malfunctioning.

1. Fill the fuel tank with clean, fresh gasoline, with a minimum octane rating of 87. To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

A. Extinguish all cigarettes, cigars, pipes and other sources of ignition.
B. Use only an approved gasoline container.

C. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before fueling.
D. Never fuel the machine indoors or in an enclosed trailer.
E. Never store the machine or fuel container where there is an open flame, spark or pilot light such as on a water heater or other appliances.
F. Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

G. Remove the machine from the truck or trailer and fuel on the ground. If this is not possible, then refuel the machine with a portable container, rather than from a gasoline dispenser nozzle.

H. Keep the nozzle in contact with the rim of fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

I. If fuel is spilled on clothing, change clothing immediately

J. Replace gas cap and tighten securely.

1. Before attempting to start the engine, move the speed adjustment lever into the neutral position, move the blade engagement switch to the OFF position, apply the parking brake, and move the neutral latches to neutral.

WARNING

DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING KIT, OR ENTIRE GRASS CATCHER INSTALLED

1. The discharge chute must always be installed and in the down position on the side discharge cutter deck except when the Scag optional grass catcher or mulching plate are properly installed.

BEFORE OPERATION CONSIDERATIONS (CONT'D)

DANGER:

ROTATING BLADES

NEVER PUT YOUR HANDS INTO THE DISCHARGE CHUTE FOR ANY REASON! Shut off the engine and remove the key and only then use a stick or similar object to remove material if clogging has occurred.

1. If the mower discharge ever plugs, shut off the engine, remove the ignition key, and wait for all movement to stop before removing the obstruction. Do not use your hand to dislodge the clogged discharge chute. Use a stick or other device to remove clogged material.
2. Check the blade mounting bolts at frequent intervals for proper tightness.
3. Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before starting the machine.

1. Before operating the mower, familiarize yourself with all mower and engine controls. Knowing the location, function and operation of these controls is important for safe and efficient operation of the mower.
2. Start the engine when the neutral latches are in the neutral lock position, the cutter blades are disengaged, the parking brake is on and the speed adjustment lever is in the neutral position.
3. Be sure the interlock switches are functioning correctly.
4. DO NOT mow when children and/or others are present. Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator. Be alert and turn the machine off if a child enters the area.

5. DO NOT carry passengers.

6. Using the machine demands attention. To prevent loss of control:

A. Mow only in daylight or when there is good artificial light.
B. Be alert for holes, rocks, roots and other hidden hazards in the terrain. Keep away from any dropoff. Beware of overhead obstructions (low limbs, etc), underground obstacles (sprinklers, pipes, tree roots, etc.). Cautiously enter a new area. Be alert for hidden hazards.
C. Do not drive close to a drop-off, ditch, creek bank, or other hazard.
D. Reduce speed and exercise extreme caution on slopes and in sharp turns to prevent tipping or loss of control. Be especially cautious when changing directions on slopes.
E. Always be sure of your footing. Keep a firm hold on the handles and walk---never run.
F. Do not operate where conditions are slippery

WARNING:

DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. ALWAYS FOLLOW OSHA APPROVED OPERATION.

1. Disengage power to the cutter deck before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.
2. Disengage power to the cutter deck before crossing roads, walks or gravel drives. Stop blades if not mowing.
3. Shut the engine off and wait until the blades come to a complete stop before removing the grass catcher container.
4. Never raise the cutter deck while the blades are rotating.

OPERATION CONSIDERATIONS (CONT'D)

DANGER:

ROTATING BLADES

NEVER PUT YOUR HANDS INTO THE DISCHARGE CHUTE FOR ANY REASON!

1. Keep hands and feet away from cutter blades and moving parts. Contact can injure.
2. DO NOT operate without the side discharge chute installed and in the down position.
3. DO NOT direct the discharge of material toward bystanders or allow anyone near the machine while in operation.
4. If the cutting blades should strike a solid object or the equipment should start to vibrate abnormally, stop the engine, disconnect the spark plug wire, and check immediately for the cause. Vibration is generally a warning of trouble. Check the machine for damaged or defective parts. Repair any damage before starting the engine or operating the cutter deck. Be sure the blades are in good condition and the blade bolts are tight.
5. Take all possible precautions when leaving the machine unattended, such as disengaging the mower, stopping the engine, and removing the key.

CAUTION:

DO NOT touch the engine or the muffler while the engine is running or immediately after stopping. These areas may be hot enough to cause a burn.

WARNING:

DO NOT run the engine inside a building or a confined area without proper ventilation. Exhaust fumes are hazardous and could cause death.

1. DO NOT operate the machine under the influence of alcohol or drugs.
2. Use care when loading or unloading the machine onto a truck or trailer.
3. Use care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.
4. Do not change the engine governor settings or overspeed the engine. See the engine operator's manual for information on engine settings.

MAINTENANCE AND STORAGE

1. Allow only trained personnel to service the machine.
2. Park the machine on level ground.
3. Never make adjustments to the machine with the engine running unless specifically instructed to do so. If the engine is running, keep hands, feet, and clothing away from moving parts.
4. Disengage drives, lower implement, stop engine and remove key or disconnect spark plug wire(s) to prevent accidental starting of the engine when servicing or adjusting the machine. Wait for all movement to stop before adjusting, cleaning or repairing.
5. If the mower must be tipped to perform maintenance or adjustment, remove the battery, drain the gasoline from the fuel tank and the oil from the crankcase.
6. Keep all nuts, bolts and screws tight, to ensure the machine is in safe working condition. Check the blade mounting bolts frequently to be sure they are tight. Replace all worn or damaged decals.
7. Clean grass and debris from cutting units, drives, mufflers, and engine to help prevent fires. Clean up oil or fuel spillage.
8. The engine must be shut off before checking the oil or adding oil to the crankcase.

MAINTENANCE AND STORAGE (CONT'D)

1. Let the engine cool before storing.
2. DO NOT store the machine near an open flame.
3. Shut off fuel while storing or transporting.
4. Always store gasoline in a safety-approved, red container.
5. Use jack stands to support components when required.
6. Carefully release pressure from components with stored energy.
7. Use care when checking blades. Wrap the blade(s) or wear gloves and use caution when servicing blades. Only replace blades. NEVER straighten or weld blades.
8. Be careful when servicing the battery as it contains acid, which is corrosive and could cause burns to skin and clothing.

WARNING:

Battery post, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

WARNING:

Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. Keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.

1. Disconnect the battery or remove sparkplug wire(s) before making any repairs. Disconnect the negative terminal first and the positive last. When finished with repair, reconnect the positive first and the negative last.

INITIAL RUN-IN PROCEDURES (FIRST DAY OF USE OR APPROXIMATELY 10 HOURS)

1. Check the belts for proper tension at 2, 4 and 8 hours. Adjust as needed.
2. Check the steering control rods for neutral adjustment (See Adjustments, page 13).
3. Check the tires for proper pressure.

Caster Wheels 25 psi.

Drive Wheels 12 psi.

1. Check for loose hardware. Tighten as needed.
2. Check the safety switches for proper adjustment:

* On electric start machines the engine should crank and start if the machine is in neutral, the PTO engagement switch is OFF and the parking brake is ON.

1. Apply lubricant to all the grease fittings.

Lubricant was applied at the factory. This is just a precautionary check to make sure that all the fittings have been lubricated.

MOWER OPERATION

1. Read and understand the safety instructions before attempting to operate this machine.
2. Before starting the engine:

* Check the oil level in the engine and the hydraulic reservoir
* Fill the fuel tank with clean, fresh, lead-free gasoline.
* Open the fuel valve on the bottom of the fuel tank.

-NOTE-

Use gasoline with an octane rating no less than 87.

* The speed adjustment lever must be in NEUTRAL.
* The blade clutch switch must be in the OFF position.
* The operator's presence levers must be released.

* The neutral latches must be in the neutral lock position.
* The key switch must be on.
* The parking brake must be on.

1. Start the engine:

* Choke as required. If the engine is cold, pull the choke knob out. When the engine starts, slowly push the choke in. If the engine stalls, repeat the above operation. When the engine is warm, choking may not be necessary.

1. Engage the cutter blades by depressing the operator presence levers and pulling the blade clutch switch into the ON position. Push the switch to the OFF position to disengage the cutter blades.

* Cold starting. In the spring and fall when the morning temperatures are cool it may be difficult to start the machine due to the parastatic load from the hydraulic drive. To relieve this load, pull out and up on the de-clutch chain located on the right side of the machine behind the tire. This will allow you to start the engine easily. When the engine is warmed up, slowly release the de-clutch chain to engage the hydraulic system.

1. Engage the cutter blades by pulling the blade clutch switch into the ON position. Push the switch to the OFF position to disengage the cutter blades.

-NOTE-

When PTO is engaged or (possibly) disengaged, a squealing sound from the underside of the machine is normal. It is caused by the electric clutch plates meshing as the mower comes up to speed. For best equipment life, engage the clutch with the engine at 3/4 throttle, not under full load.

WARNING:

If you are not familiar with the operation of the hydrostatic drive and zero turn feature, practice turning and maneuvering with the hand controls before engaging the cutter blades.

1. Release the parking brake. Move the speed adjustment lever to the desired mowing speed.

-NOTE-

Top speed is suggested only for transport!

1. While squeezing the steering brake levers with both hands, release both neutral latches.
2. When the steering brake levers are released, the machine will travel straight. To make a right turn, squeeze the RH lever. To turn left, squeeze the LH lever.
3. TO STOP, squeeze both levers, lock the neutral latches, and move the speed adjustment lever to neutral.
4. To move the machine in reverse, squeeze up on both steering control levers.
5. To "freewheel" or move the machine around without the engine running, turn the dump valve levers located at the back of the pumps to the "freewheel" positions (see Figure 1). To operate the machine, the dump valve levers must be returned to the closed positions.

Dump Valve Levers
(closed position)
SWZ05DMPVLV

Figure 1. Dump Valves

BELT TENSION

CAUTION:

Stop engine and remove the key from the ignition before making any adjustments. Wait for all moving parts to come to a complete stop before beginning work.

-NOTE-

All the belts on the SWZU are spring loaded and do not require adjustment. Check the belts for excessive wear or damage daily for the first week. After the first week, check the belts monthly.

1. Remove the belt covers.
2. Inspect the belts for wear, cracking, or glazing. Contact your Scag dealer if any unusual wear is noted.
3. Replace the belt covers.

CUTTER DECK ADJUSTMENTS

Due to the many cutting conditions that exist, it is difficult to suggest a cutter deck setting that will work for every lawn. There are two adjustments that can be made on these decks, pitch and height.

PITCH is the angle of the blades (comparing front to rear). A 1/4" downward pitch (front of deck down) is recommended for best cutting performance.

HEIGHT is the nominal distance the blade is off of the ground. This measurement is made with the blades pointed side to side and distance is measured between cutting tip and ground.

Changes to the cutting height can be achieved by repositioning the cutter deck. There are eight available positions from 1" to 4-1/2" (See Figure 2).

WARNING:

Do not adjust the cutting height with the mower blades rotating. Shut off the engine and remove the ignition key. Bodily injury could occur from the rotating blades.

1. Shut off the engine and remove the ignition key.
2. While holding up on the deck support handle, remove the two hairpins from the adjusting pins on one side of the cutter deck (See Figure 2).
3. Lift or lower the deck to the desired cutting height and reinstall the hairpins. A deck height decal is located on the deck mounting frame as an aid in adjusting the deck to the desired height.
4. Repeat the above process on the opposite side of the cutter deck.

Figure 2. Cutting Height Adjustment

CUTTER DECK PITCH ADJUSTMENTS

The cutter deck pitch adjustment has been set at the factory and normally will not need to be changed.

However, if the pitch needs to be adjusted due to service work performed on the deck, follow the procedure below (see Figure 3, Page 11).

1. Shut off the engine and remove the key.
2. Support the cutter deck with four blocks (you will be removing the hair pins to make this adjustment).
3. Remove the front hair pins from the front deck support pins.
4. Loosen the jam nuts on the deck support pins.

CUTTER DECK ADJUSTMENTS (CONT'D)

1. Turn the deck support pins to lengthen or shorten the pins to reach the desired result.
2. Tighten the jam nut, replace the hair pin, and remove the blocks. Check that the desired deck pitch is achieved.

Figure 3. Deck Pitch Adjustment

CUTTER BLADES

Do not sharpen beyond 1/3 of the width of the blade. (See Figure 4).

WARNING:

Blades have a sharp cutting edge. Wear proper eye protection and protective gloves or wrap blades with protective material when removing, sharpening and installing blades.

-NOTE-

Dress the blade with a file. Using a wheel grinder may burn the blade. Check the balance of the blade. If blades are out of balance, vibration and premature wear of spindle assembly can occur. See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades.

Figure 4. Blade Sharpening

Custom-Cut Baffle Adjustment

The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut. The baffle can be set in three (3) different positions for optimum performance.

A. 3" Position - baffle is installed using the top set of holes on the front baffle welded inside the cutter deck. (See Figure 6, Page 12). The Advantage cutter deck will deliver the best quality-of-cut in very tall, wiry, tough to cut grass.
B. 3-1/2" Position (factory setting) - baffle is installed using the middle set of holes on the front baffle welded inside the cutter deck. (See Figure 7, Page 12). For general purpose cutting, place the Custom Cut Baffle in the 3-1/2" position. This gives the best mix of cutting performance in all types of grass.
C. 4" Position - baffle is installed using the bottom set of holes on the front baffle welded inside the cutter deck. (See Figure 8, Page 12). Placing the baffle in the 4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

To Adjust the Custom-Cut Baffle height:

1. Remove the hardware securing the Custom-Cut Baffle to the cutter deck (See Figure 5, Page 12).

CUSTOM-CUT BAFFLE ADJUSTMENT (CONT'D)

-NOTE-

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on the cutter deck size.

Figure 5. Custom-Cut Baffle

1. Move the Custom-Cut Baffle to desired position. (See Figures 6 through 8 for position)
2. Reinstall the mounting hardware as shown. (See Figures 6 though 8). Torque hardware to 39ft.lbs.

Figure 6. 3" Custom-Cut Baffle Position

Figure 7. 3-1/2" Custom-Cut Baffle Position

Figure 8. 4" Custom-Cut Baffle Position

NEUTRAL ADJUSTMENT

-NOTE-

Neutral has been set by your Scag dealer at the time of setup and normally does not need to be adjusted. If, however, you find that the neutral has come out of adjustment, follow the procedure below.

1. Raise the drive wheels off the ground and block the caster wheels to prevent the machine from moving.
2. Make sure the speed control lever is in neutral, the steering control levers are in the neutral latch position, and the parking brake is on. Start the engine.
3. Release the parking brake and note if the tires are rotating.
4. Starting on the left side of the machine, using the adjustment wrench located on the left side of the machine. Rotate the tracking adjustment nut counter clockwise just until the LH wheel starts to creep forward. Make a note of the position of the adjustment nut. (See Figure 9, Page 13).
5. Turn the adjustment nut clockwise just until the wheel turns rearward. Make a note of the position of the adjustment nut. To adjust neutral, split the difference between the two noted positions of the adjustment nut. Repeat on the right side as needed.
6. Place the wrench in the holder on the left side of the machine and turn the engine off.

NEUTRAL ADJUSTMENT (CONT'D)

Figure 9. Neutral Adjustment

STEERING CONTROL ROD ADJUSTMENT

-NOTE-

This adjustment is made to allow the steering control levers to be moved out of the neutral latch without engaging reverse.

Before making this adjustment be sure that the speed control bearing is just touching the speed control cam and that the bellcrank bearing is resting in the center groove of the neutral cam.

1. Remove the speed control spring. Remove the steering control rod swivel hair pin. Check the location of the swivel in the slotted hole in the bell crank.
2. Turn the swivel joint on the steering control rods until the swivel joint is centered in the slot in the bellcrank.

Figure 10. Control Rod Adjustment

1. Reinstall the speed control spring onto the swivel. Install the hair pin onto the swivel. (See Figure 10).

TRACKING ADJUSTMENT

-NOTE-

Before proceeding with this adjustment, be sure that the tire pressures are correct, (see page 8) and that the neutral adjustment and the steering control rod adjustment have been completed.

1. With the machine on a flat level surface, start the engine and place the speed adjustment lever into the speed that will most often be used.
2. Squeeze the steering control levers and release the neutral latch. Slowly release the steering control levers, allowing the machine to move forward.

WARNING:

BEFORE ATTEMPTING TO MAKE ANY TRACKING ADJUSTMENTS:

1. Move the speed adjustment lever to the neutral position.
2. Place the blade engagement switch in the OFF position.
3. Apply the parking brake.

4. Move the steering control levers into the neutral position.

5. If the machine pulls to one side. Stop the mower by placing the steering control levers in the neutral position. Using the adjustment wrench located on the left side of the machine, turn the tracking adjustment nut on the slower side counter clockwise until the machine tracks straight. (See Figure 11, Page 14).

6. Bring the steering control levers back to the neutral lock position and check to see that the machine does not creep forward on the adjusted wheel.
7. If the machine creeps in neutral you have moved out of the neutral band and will have to turn the tracking adjustment nut clockwise until the machine does not creep.

TRACKING ADJUSTMENT (CONT'D)

1. Repeat steps 1 and 2. If the machine continues to pull to one side, stop the mower by placing the steering control levers in the neutral position. Turn the tracking adjustment nut on the faster side clockwise until the machine tracks straight.
2. If tracking cannot be achieved, contact your Scag servicing dealer.

Figure 11. Tracking Adjustment

PARKING BRAKE

1. Adjust the parking brake so that when the brake hand lever is against the stop on the handle bar, the brake levers on the brake shaft weldment are against the stops on the engine deck.

CAUTION:

Adjust the brake only enough to hold the machine. Excessive force may cause damage to the machine or brake components.

1. Adjust the brake actuator rod on either side of the machine to obtain proper brake adjustment.

BREAK-IN			+ Grease spindle until grease comes out the relief valveCompatible Greases: Lidok EP #2 (found at industrial shops)Ronex MP (Exxon service stations)Shell Alvania (Shell service stations)Mobilux #2 (Mobil service stations)Super Lub M EP #2 (Conoco service stations)
X X		500 HRS OR ANNUALLY	PROCEDURE	COMMENTS
			Check all hardware for proper tightnessChange engine oil and filter at 5 hours
	X		Check engine oilRemove debris from under belt coverSharpen cutter bladesGrease spindle bearingsClean air filterCheck belt tensionCheck tire pressureCheck battery level	Do not over fillMore often if neededMore often if needed+ US Lithium MP White Grease 2125More often if neededAdjust as neededAdd or adjust as requiredAdjust as needed
	X
		X	Replace air filterGrease caster wheel bearingsGrease caster wheel pivot shaftsGrease idler pulley bracket on cutter deckChange hydrostatic oil filterChange engine oil and filterGrease idler arm pivotsGrease brake hand leverGrease brake actuator levers	More often if neededChassis greaseChassis greaseChassis greaseClean area before removing the filterSee engine manufacturer informationChassis greaseChassis greaseChassis grease
		X	Check all hardware for proper tightnessAdjust air gap on electric clutchDrain hydraulic system and replace oil	Contact your Scag dealer for information about making this adjustment.

HYDRAULIC SYSTEM

Checking Hydraulic Oil Level

The hydraulic oil level should be checked after the first 10 hours of operation. Thereafter, check the oil every 200 hours of machine operation or monthly, whichever occurs first.

-IMPORTANT-

If the oil level is consistently low, check for leaks and correct immediately.

1. Wipe dirt and contaminants from around the reservoir cap. Remove the cap from the hydraulic oil reservoir.

2. Visually check the level of hydraulic oil. Hydraulic oil must be at least 2" inches from top of the filler neck. If the level cannot be determined visually, use a clean tape measure to check the level. If the fluid is low, add 20W50 motor oil. DO NOT overfill; (overfilling the oil reservoir may cause oil seepage around the cap area).

3. Clean the fill cap and install it onto the reservoir.

Changing Hydraulic Oil

The hydraulic oil should be changed after every 500 hours or annually, whichever occurs first. The oil should also be changed if the color of the fluid has become black or milky. A black color and/or a rancid odor usually indicates possible overheating of the oil, and a milky color usually indicates water in the hydraulic oil.

-NOTE-

The hydraulic oil should be changed if you notice the presence of water or a rancid odor to the hydraulic oil.

1. Park the mower on a level surface and stop the engine.

2. Place a suitable container under the hydraulic oil drain. Remove the fill cap from the reservoir. Remove the drain cap from the T-Fitting located on the hydraulic system filter head. (See Figure 12). Allow the fluid to drain into the container and properly discard it.

Figure 12 Hydraulic Oil Drain Cap

1. Reinstall the drain cap onto the T-Fitting and be sure it is tight.

-NOTE-

Before refilling the hydraulic oil reservoir the hydraulic oil filter should be changed as well. See instructions outlined below.

1. Fill the reservoir to 2" inches from the top of the filler neck with 20W50 motor oil.
2. Replace the reservoir fill cap. Start the engine and drive forward and backward for two minutes. Check the oil level in the reservoir. If necessary, add oil to the reservoir.

Changing Hydraulic Oil Filter Element

The hydraulic oil filter should be changed after every 500 hours of operation or annually, whichever occurs first.

1. Remove the oil filter element (Figure 12) and properly discard it. Fill the new filter with clean oil and install the filter. Hand tighten only.

2. Run the engine at idle speed with the speed control lever in neutral for five minutes.

3. Check the oil level in the hydraulic tank. It must be 2" inches from the top of the filler neck. If necessary, add SAE 20W50 motor oil.

Checking Engine Crankcase Oil Level

The engine oil level should be checked after every 8 hours of operation or daily as instructed in the Engine Operator's Manual furnished with this mower.

Changing Engine Crankcase Oil

After the first 5 hours of operation, change the engine crankcase oil and replace the oil filter. Thereafter, change the engine crankcase oil after every 100 hours of operation or bi-weekly, whichever occurs first. Refer to the Engine Operator's Manual furnished with this mower for instructions.

Changing Engine Oil Filter

After the first 5 hours of operation, replace the engine oil filter. Thereafter, replace the oil filter every 200 hours of operation or every month, whichever occurs first. Refer to Engine Operator's Manual for instructions.

Engine Air Cleaner

For any air cleaner, the operating environment dictates how often the air cleaner should be serviced. Refer to the Engine Operator's Manual furnished with this mower for instructions.

-NOTE-

In extremely dusty conditions it may be necessary to service the air cleaner daily to prevent engine damage.

BATTERY (ELECTRIC START UNITS ONLY)

Checking Electrolyte Level and Cleaning Battery

This machine was equipped from the factory with a sealed battery. Maintenance is not required to maintain the electrolyte level. Dirt and fluid on the top of the battery can cause the battery to discharge. Corrosion of the battery terminals or loose connections will cause poor battery performance.

WARNING:

Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. Keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.

WARNING:

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer and reproductive harm. Wash hands after handling.

1. Loosen the two plastic wing nuts and then remove the battery cover.
2. Clean the cable ends and battery posts with steel wool. Use a solution of baking soda and water to clean the battery. Do not allow the solution to enter the battery cells.
3. Tighten the cable connections securely and apply a light coat of silicone dielectric grease to the terminal connections to prevent corrosion.
4. Install the battery cover.

WARNING:

Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEVERE CHEMICAL BURNS. Avoid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NOT tip any battery beyond 45° angle in any direction. If fluid contact does occur, follow first aid suggestions below.

BATTERY ELECTROLYTE FIRST AID

EXTERNAL CONTACT - Flush with water.

EYES - Flush with water for at least 15 minutes and get medical attention immediately.

INTERNAL - Drink large quantities of water. Follow with Milk Of Magnesia, beaten egg, or vegetable oil. Get medical attention immediately. In case of internal contact, DO NOT give fluids that would induce vomiting.

Charging the Battery

Unplug charger before connecting or disconnecting from the battery. Refer to the battery charger's manual for specific instructions.

Under normal conditions the engine's alternator will have no problem keeping a charge on the battery. If the battery has been completely discharged for a long period of time, the alternator may not be able to recharge the battery, and a battery charger will be required.

DO NOT charge a frozen battery. It may explode and cause injury. Let the battery warm before attaching a charger.

Whenever possible, remove the battery from the mower before charging.

Wear protective clothing and use insulated tools

WARNING:

BATTERIES PRODUCE EXPLOSIVE GASES. Charge the battery in a well ventilated space so gases produced while charging can dissipate.

Charging rates between 3 and 50 amperes are satisfactory if excessive gassing or spewing of electrolyte does not occur or the battery does not feel excessively hot (over 125° F). If spewing or gassing occurs or the temperature exceeds 125° F, the charging rate must be reduced or temporarily stopped to permit cooling.

Jump Starting

1. The booster battery must be a 12 volt type. If a vehicle is used for jump starting, it must have a negative ground system.
2. When connecting the jumper cables, connect the positive cable to the positive battery post, then connect the negative cable to the negative battery post.

CLEANING THE MACHINE

CAUTION:

Do not wash any portion of the equipment while it is hot. Do not wash the engine; use compressed air.

1. After each use, wash the mower and cutter deck. Use cold water and automotive cleaners. Do not use pressure cleaners.
2. Do not spray electrical components.
3. Repair damaged metal surfaces using Scag touch-up paint (P/N 48521) available from your authorized Scag dealer. Wax the mower with an automotive paint wax for maximum paint protection.

TROUBLESHOOTING CUTTING CONDITIONS

CONDITION	CAUSE	CURE
Stringers - Occasional Blades of Uncut Grass	Low engine RPM	Run engine at full 3600 RPM
	Ground speed too fast	Slow speed to adjust for conditions
	Wet grass	Cut grass after it has dried out
	Dull blades, incorrect sharpening	Sharpen blades
	Deck plugged, grass accumulation	Clean underside of deck
	Belts slipping	Adjust belt tensions
Streaking - Strips of Uncut Grass in Cutting Path	Dull, worn blades	Sharpen blades
	Incorrect blade sharpening	Sharpen blades
	Low engine RPM	Run engine at full 3600 RPM
	Belt slipping	Adjust belt tension
	Deck plugged, grass accumulation	Clean underside of deck
	Ground speed too fast	Slow speed to adjust for conditions
	Wet grass	Cut grass after it has dried out
	Bent blades	Replace blades
Streaking - Strips of Uncut Grass Between Cutting Paths	Not enough overlapping between rows	Increase the overlap of each pass

TROUBLESHOOTING CUTTING CONDITIONS

CONDITION	CAUSE	CURE
Uneven Cut on Flat Ground - Wavy High-Low Appearance, Scalloped Cut, or Rough Contour	Lift worn off of blade	Replace blade
	Blade upside down	Mount with cutting edge toward ground
	Deck plugged, grass accumulation	Clean underside of deck
	Too much blade angle (deck pitch)	Adjust pitch and level
	Deck mounted improperly	See your authorized SCAG dealer
	Bent spindle area	See your authorized SCAG dealer
	Dull blade	Sharpen blade
Uneven Cut on Uneven Ground - Wavy Appearance, High-Low Scalloped Cut, or Rough Contour	Uneven ground	May need to reduce ground speed, raise cutting height, and/or change direction of cut
Width of Deck SGB021
Sloping Ridge Across Width of Cutting Path	Tire pressures not equal	Check and adjust tire pressure
	Wheels uneven	Check and adjust tire pressure
	Deck mounted incorrectly	See your authorized SCAG dealer
Width of Deck SGB023

TROUBLESHOOTING CUTTING CONDITIONS

CONDITION	CAUSE	CURE
Scalping - BladesHitting Dirt orCutting Very Close tothe Ground	Low tire pressures	Check and adjust pressures
	Ground speed too fast	Slow speed to adjust for conditions
	Cutting too low	May need to reduce ground speed,raise cutting height, change directionof cut, and/or change pitch and level
	Rough terrain	May need to reduce ground speed,raise cutting height, and/or changedirection of cut
	Ground speed too fast	Slow speed to adjust for conditions
	Wet grass	Cut grass after it has dried out
Step CutRidge in Center ofCutting Path	Blades not mounted evenly	Adjust pitch and level
	Bent blade	Replace blade
	Internal spindle failure	See your authorized SCAG dealer
	Mounting of spindle incorrect	See your authorized SCAG dealer
Slope Cut - SlopingRidges Across Widthof Cutting Path	Bent spindle mounting area	See your authorized SCAG dealer
	Internal spindle failure	See your authorized SCAG dealer
	Bent deck housing	See your authorized SCAG dealer

TECHNICAL SPECIFICATIONS

ENGINES

General Type:

Brand:

Models:

Horsepower:

Type:

Displacement:

Cylinders:

Governor:

Exhaust Group:

Fuel Pump Group:

Oil Pump Group:

Valve Group:

Starter/Electrical:

Charging System:

ENGINE DECK

Thickness:

Fuel Tank:

Drive Wheels/Tires:

Brakes:

Parking Brakes:

Axles:

Handle Bars:

DRIVE SYSTEM

Type:

Hydro Pumps:

Drive Wheel Motors:

Hydro Fluid Cooling Group:

Steering / Travel Control::

Dump Valves:

Axles:

Wire Harness:

Safety Group:

Forward Speed Range:

Reverse Speed Range:

Date of Issue: July, 2004

Specifications Subject to Change Without Notice

Heavy duty industrial/commercial

Kohler, Kawasaki, Honda

Kohler CV493T, Kawasaki FH451V (15HP), FH500V (17HP)

FH580V (19HP), FH641V (21HP), Honda GXV610QAF (18HP)

Kohler 18HP; Kaw. 15HP; Kaw. 17HP; Kaw. 19HP; Kaw. 21HP; Honda 18HP

4 cycle gas, vertical shaft engines

Kohler: 18HP=490cc

Kawasaki: 15HP=494cc, 17HP=494cc, 19HP=585cc, 21HP=675cc

Honda: 18HP=615cc

Varied - see manufacturer's specifications

Mechanical type governor with variable speed control. Settings:

Kawasaki 15HP=3600 rpm (+/-75 rpm), idle set at 1200 rpm

(+/-75 rpm), 17HP & 21HP=3600 rpm (+/-75 rpm), idle set at

1550 rpm (+/-75 rpm), 19HP=3600 rpm (+/-100 rpm), idle set at

1550 rpm (+/-150 rpm), Kohler 18HP=3600 rpm (+/-50 rpm), idle

set at 1500 rpm (+/-75 rpm), Honda 18HP=3600 rpm (+/-150 rpm), idle set at 1700 rpm (+/-150 rpm).

Single & dual exhaust canister muffler

Varied - See manufacturer's specifications

Varied - See manufacturer's specifications

Varied - See manufacturer's specifications

Electronic Ignition with recoil starter or 12 volt battery with

alternator, solid state ignition with key start

Varied - See manufacturers specifications

7 gauge steel

6 gallon (19.0 litres) seamless polyethylene with integral cup holder.

SWZU36A - 16 x 6.50-8 four-ply pneumatic tubeless

SWZU48A & 52A - 18 x 8.50-8 four-ply pneumatic tubeless

Dynamic braking through hydro drive system

7.5" drum, band brake, one on each wheel

1" tapered

1-1/4" diameter

Hydro drive with two variable displacement pumps and two cast-iron high torque motors

Two Hydro-Gear Model BDP 10A pumps with dump valves for movement without running the engine

Two 12 cu. inch cast-iron high torque motors

4qt. capacity nylon cooling reservoir, uses, SAE 20W50 fluid and

10 micron filter

Independent handle controls for each wheel, squeeze to move

from forward to neutral to reverse, neutral lock lever, speed range controlled with single lever (patented design), in-field tracking adjustment with tool provided

Allows for movement without engine running

1" tapered motor shafts

14 gauge wire

Handle actuated operator presence system (patented design),

blade / clutch and transmission interlock to engine kill

0 to 7.4 mph

0 to 3.0 mph

TECHNICAL SPECIFICATIONS (CON'T)

CUTTER DECKS
	SWMU 36 Advantage, SWMU 48 Advantage, SWMU 52 Advantage, SWMU 61 Advantage.
Type:	Out-front design with anti-scalp rollers
Construction:	SWMU36A, 48A: 7-gauge steel with 7-gauge (3/16") steel skirtSWMU52A, 61A:10-gauge steel with 7-gauge (3/16") steel skirt
Cutting Width:	35.5" (90.2 cm), 48.0 (122.0 cm), 52.0 " (132.0 cm), 61.0 " (155.0 cm).
Cutting Height Adjustment:	Adjustable from 1-3/4" to 4-1/4" in 1/4" increments
Cutter Blades:	MarbainTM, .197 thicknessSWMU 36: Two (2) 18"; SWMU 48: Three (3) 16.5"SWMU 52: Three (3) 18"; SWMU 61: Three (3) 21"
Blade Engagement:	Electric blade brake clutch with instrument panel switch
Discharge Opening:	Extra wide 11.5", 13.75 " discharge opening with hinged chute
Caster Wheels:	11 x 4.5-5 smooth tread flotation, inner tubes, split rims, roller bearings, with quick pin removal
Spindles:	Cast housing, taper roller bearing, low maintenance with top access grease fitting and grease overfill relief poppet
Spindle Pulleys:	Split steel with easily removed taper hubs
Idler Pulley:	5" diameter pulley, welded and riveted construction, 1-3/8" O.D. Bearings
Idler Arm:	Heavy duty dual ball bearing mounting
Cutter Deck Belts:	B-section with Kevlar cord

ADDITIONAL SPECIFICATIONS

OPTIONAL ITEMS/ATTACHMENTS

Fabric Grass Catcher:	GC-F4 Grass Catcher with 4 cubic ft. capacity
Metal Grass Catcher:	GC-4D Grass Catcher with 4 cubic ft. capacity and rope pull dump or pick-up and dump
Turbo-Baffle	High velocity discharge baffle. Improves quality-of-cut, and discharge disbursement.
Hurricane Mulch Kit:	The unique Hurricane Mulch SystemTM employs "eye of the hurricane" mulching plates combined with bolt-in v-baffles, flow directors, Eliminator blades, and a side discharge close-off plate.
Cup Holder:	Enable operator to safely and conveniently carry a beverage with them.

APPROXIMATE DIMENSIONS	SWZU36A	SWZU48A	SWZU52A	SWZU61A
Length:	77.5"	78"	79"	79.0"
Length with Grass Catcher:	77.5"	78"	79"	79.0"
Tracking Width:	36.0"	37.0"	37.0"	41.0"
Width:	46.5"	59.0"	60"	70.0"
Width (with discharge chute up):	37.5"	49.0"	53"	62.0"
With with grass catcher:	55.0"	68.0"	71"	80.0"
Height:	43"	41"	40.5"	40.5"
Height with grass catcher:	43"	41"	40.5"	40.5"
Weight	575 lbs.	650 lbs	655 lbs	665 lbs.
Weight with grass catcher:	615 lbs.	690 lbs	695 lbs.	705 lbs.
Turning Radius:	Zero	Zero	Zero	Zero

36"A CUTTER DECKS

36"A CUTTER DECKS

Ref. No.	Part Number	Description	Ref. No.	Part Number	Description
1	461784	Cutter Deck (Includes Decals)	37	04021-07	Nut, 1/2-13 Elastic Stop
2	04017-27	Capscrew, 3/8-16 x 1.0" Serrated Flange Hex Hd	38	48038	Guide, Roller
3	422478	Bracket, Anti-Scalp Wheel	39	04001-09	Bolt, Hex Head 5/16-18 x 1"
4	04021-05	Lock Nut, 3/8-16 Center Lock	40	451118	Roller Shaft
5	48100-15	Bushing, .376" ID Oilite	41	48926	Tapered Hub
6	481632	Wheel, Anti-Scalp (Incl. Item 5)	42	482744	Pulley
7	04003-26	Bolt, Carriage 3/8-16 x 4"	43	481880	Belt, Cutter Deck
8	481838	Pin Assy., Deck Adj. (Incl. Items 10 & 11)	44	04001-172	Bolt, Hex Head 1/4-20 x 1" Gr. 8
9	43512	Spacer, Deck Adjustment Pin	45	04020-09	Hex Nut, 5/8-11
10	481539	Rod End, Male 3/8-24 RH Thread	46	482245	Spring, Chute Return
11	04020-25	Nut, 3/8-24 Jam	47	04021-22	Lock Nut, 5/16-18 Elastic Stop Grade 8
12	461663	Spindle Assembly	48	04043-04	Flatwasher, 3/8" (.938 x .391 x .105)
13	04019-03	Nut, 5/16-18 Serrated Flange	49	04019-04	Nut, 3/8-16 Serrated Flange
14	04063-08	Key,1/4" x 1/4" x 2"	50	461295	Discharge Chute
15	04030-03	Lock Washer 5/16"	51	04001-54	Capscrew, Hex Head 3/8-16 x 3"
16	43590	Spacer, Spindle	52	04001-136	Capscrew, Hex Head 3/8-16 x 1-1/2"
17	04043-06	Flatwasher, 5/8 W	53	43657	Pivot, Idler
18	04001-41	Bolt, Hex Head 5/8-11 x 9-1/2"	54	04001-62	Capscrew, Hex Head 38/16 x 3-1/4"
19	481707	Cutter Blade, 18"	55	422713	Base, Idler Pivot
19A	481711	Cutter Blade, 18" Hi Lift	56	04003-04	Bolt, Carriage 5/16-18 x 1"
20	43589	Spindle Shaft	57	461174	Idler Arm Weldment (Includes Item 58)
21	481024	Seal, Cutter Spindle Top	58	48224	Ball Bearing
22	481022	Tapered Bearing Set (Two Bearings W/Race)	59	04001-154	Bolt, Hex Head 5/16-18 x 4-3/4"
23	48114-04	Grease Fitting	60	422763	Belt Cover, RH
24	48677	Relief Fitting, Cutter Spindle	61	481597	Spring, Deck Idler
25	43644	Spindle Housing	62	482783	Pulley, Idler
26	43312	Spacer, Outside	63	04001-175	Bolt, Hex Head 5/16-18 x 1-1/2" Grade 8
27	43296	Spacer, Inside	64	04001-12	Bolt, Hex Head 5/16-18 x 1-3/4"
28	481025	Seal, Cutter Spindle Bottom	65	423783	Baffle Weldment
29	43297	Spindle Bushing	66	04019-03	Nut, 5/16-18 Serrated Flange
30	481035	Nut, Spindle	67	04003-23	Bolt, Carriage 3/8-16 x 1"
31	422762	Belt Cover, LH	68	461755	Push Arm - LH (Includes Items 36, 69 & 70)
32	481625-01	Wing Nut, 3/8-16	68A	461756	Push Arm - RH (Includes Items 36, 69 & 70)
33	04021-09	Nut, 3/8-16 Elastic Stop	69	48542	Rod End, Male 1/2-20 RH Thread
34	04110-03	U-Nut, 3/8-16	70	04020-08	Nut, 1/2-20 Jam
35	04001-31	Bolt, Hex Head 3/8-16 x 2-1/2"	71	451724	Push Arm Shaft
36	48114-08	Grease Fitting, 90 Degree	72	04001-74	Bolt, Hex Head 1/2-13 x 3"

48"A, 52"A & 61"A CUTTER DECKS

SWZU05CD48A,52A&61A

48"A, 52"A & 61"A CUTTER DECKS

Ref. No.	Part No.	Description	48	52	61	Ref. No.	Part No.	Description	48	52	61
1	461785	Cutter Deck W/ Decals	x			51	04001-74	Bolt, Hex Head 1/2-13 x 3"	x	x	x
	461786*	Cutter Deck W/ Decals (small frame)		x		52	04020-09	Hex Nut, 5/8-11	x	x	x
	461787*	Cutter Deck W/ Decals (large frame)		x		53	04021-07	Hex Nut, 1/2-13 Elastic Stop	x
	461788	Cutter Deck W/ Decals			x	54	422745	Belt Cover, RH	x	x
2	04017-27	Capscrew, 3/8-16 x 1" Serr. Flng.	x	x	x		422911	Belt Cover, RH			x
3	04021-05	Lock Nut, 3/8-16 Center Lock	x	x	x	55	04003-23	Bolt, Carriage 3/8-16 x 1"	x	x	x
4	48100-15	Bushing, .376" ID Oilite	x	x	x	56	461632	Idler Arm Weldment (Incl. Item 10)	x	x	x
5	481632	Wheel, Anti-Scalp	x	x	x	57	04001-54	Capscrew, Hex Head 3/8-16 x 3"	x	x	x
6	422478	Bracket, Anti-Scalp Wheel	x	x	x	58	461295	Discharge Chute	x	x
7	04003-26	Bolt, Carriage 3/8-16 x 4"	x	x	x		461296	Discharge Chute			x
8	04021-09	Hex Nut, 3/8-16 Elastic Stop	x	x	x	59	04019-03	Nut, 5/16-18 Serrated Flange	x	x	x
9	04043-04	Flatwasher, 3/8" (.938 x .391 x .105)	x	x	x	60	482797	Spring, Deck Idler	x	x	x
10	48224	Ball Bearings	x	x	x	61	04001-154	Bolt, Hex Head 5/16-18 x 4-1/4"	x	x	x
11	04110-03	U-Nut, 3/8-16	x	x	x	62	482245	Spring, Chute Return	x	x	x
12	43660	Pivot, Idler	x	x	x	63	04021-09	Nut, 3/8-16 Elastic Stop	x	x	x
13	48542	Rod End, Male 1/2-20 RH Thread	x	x	x	64	423786	Baffle Weldment 48A	x
14	482416	Pulley, Idler	x	x	x	64A	423803	Baffle Weldment 52A		x
15	461755	Push Arm - LH (Incl. 13, 19 & 49)	x	x	x	64B	423792	Baffle Weldment 61A			x
16	461766	Push Arm - RH (Incl. 13, 19 & 49)	x	x	x	65	04001-31	Bolt, Hex Head 3/8-16 x 2-1/2"	x	x	x
17	04001-136	Capscrew, Hex Head 3/8-16 x 1-1/2"	x	x	x	66	04063-08	Key, 1/4" x 1/4" x 2"	x	x	x
18	04019-04	Nut, 3/8-16 Serrated Flange	x	x	x	67	482783	Pulley, Idler	x	x	x
19	04020-08	Nut, 1/2-20 Jam	x	x	x	68	451724	Push Arm Shaft	x	x	x
20	481838	Pin Assembly (Incl. 21 & 23)	x	x	x	69	422744	Belt Cover LH	x	x
21	04020-25	Nut, 3/8-24 Jam	x	x	x		422910	Belt Cover LH			x
22	43512	Spacer, Deck Adjustment Pin	x	x	x	70	04021-10	Hex Nut, 5/16-18 Elastic Stop	x	x	x
23	481539	Rod End, Male 3/8-24	x	x	x	71	04001-172	Bolt, Hex Head 1/4-20 x 1" Gr. 8	x	x	x
24	461663	Spindle Assembly	x	x	x	72	04001-11	Bolt, Hex Head 5/16-18 x 1-1/2"	x	x	x
25	43590	Spacer, Spindle	x	x	x	73	04001-12	Bolt, Hex Head 5/16-18 x 1-3/4"	x	x	x
26	04001-41	Bolt,Hex Head 5/8-11 x 9-1/2"	x	x	x
27	04043-06	Flatwasher, 5/8 W	x	x	x
28	481706	Cutter Blade 16-1/2"	x
28	481707	Cutter Blade 18"		x
28	481708	Cutter Blade 21"			x
28A	481710	Cutter Blade 16-1/2" Hi Lift	x
28A	481711	Cutter Blade 18" Hi Lift		x
28A	481712	Cutter Blade 21" Hi Lift			x
29	04001-176	Bolt, Hex Head 5/16-18 x 1-3/4" Gr 8	x	x	x
30	43589	Spindle Shaft	x	x	x
31	481024	Seal, Cutter Spindle - Top	x	x	x
32	481022	Tapered Bearings (Two)	x	x	x
33	48114-04	Grease Fitting	x	x	x
34	43644	Spindle Housing	x	x	x
35	48677	Relief Fitting, Cutter Spindle	x	x	x
36	43312	Spacer Outside	x	x	x
37	43296	Spacer, Inside	x	x	x
38	481025	Seal, Cutter Spindle - Bottom	x	x	x
39	43297	Spindle Bushing	x	x	x
40	481035	Nut, Spindle	x	x	x
41	481625-01	Wing Nut, 3/8-16	x	x	x
42	451118	Roller Shaft (small frame)	x	x
	45944	Roller Shaft (large frame)		x	x
43	04001-09	Bolt, Hex Head 5/16-18 x 1"	x	x	x
44	04021-22	Hex Nut, 5/16-18 Elastic Stop Gr. 8	x	x	x
45	04030-03	Lock Washer 5/16"	x	x	x
46	48926	Tapered Hub	x	x	x
47	48038	Guide, Roller	x	x	x
48	482744	Pulley, 5.75 O.D.	x	x
48A	482745	Puley, 6.35 O.D.			x
49	481104-08	Grease Fitting, 90 Degree	x	x	x
50	482281	Belt, Deck Drive	x
	483012	Belt, Deck Drive		x
	483011	Belt, Deck Drive			x

* Measure the engine deck to determine frame size. 461786 is for small frame (16") & 461787 is for large frame (20")

36"A DECK FRAME

SWZU05DF36

36"A DECK FRAME

Ref. No.	Part No.	Description
1	461170	Belt Cover With Decal
2	481625-01	Knob With Stud
3	04029-03	Knob, Deck Cover Mounting
4	48100-08	Bushing, Caster
5	461790	Frame Weldment, Deck Mounting - 36" (Includes Item #28)
6	04062-04	Hair Pin Cotter, .177" x 3-1/4"
7	48114-04	Grease Fitting Str. 1/4-28 Self Tap
8	04066-01	Quick Pin, .438" Dia.
9	04024-02	Nut, Push-On - 3/8" Dia.
10	04041-07	Flatwasher, 3/8" (.391 x .938 x .105)
11	04019-04	Nut, 3/8-16 Serrated Flange Hex Head
12	45325	Yoke, Caster Wheel
13	04001-80	Capscrew, Hex Head 1/2-13 x 6-1/2"
14	04021-07	Locknut, 1/2-13 Elastic Stop
15	481843	Wheel Assembly, Caster
16	481845	Tire, 11 x 4.00-5
17	481770	Retainer
18	481846	Roller Bearing
19	481844	Rim, 5.0" x 2.75" (Includes #20 & 23)
20	48114-05	Grease Fitting Str. 1/4-28
21	481769	Roller Bearing .625 x 3.25"
22	04001-46	Capscrew, Hex Head 3/8-16 x 2-1/4"
23	*	Tire Valve, Purchase Locally
24	43511	Sleeve, Caster Wheel
25	04040-10	Flatwasher, 5/8" - (.688 x 1.75 x .134)
26	04017-36	Capscrew, 1/2-13 x 1" Serrated Flange Hex Head
27	04112-05	Nut, 1/2-13 Spiralock
28	04110-03	U-Nut, 3/8-16

48"A AND 52"A - DECK FRAME (SMALL FRAME)

SWZU05DF48-52

48"A AND 52"A - DECK FRAME (*SMALL FRAME)

Ref. No.	Part No.	Description
1	461753	48" Belt Cover With Decal
	461754	52" Belt Cover With Decal
2	481625-01	Knob With Stud
3	04029-03	Knob, Deck Cover Mounting
4	48100-08	Bushing, Caster
5	461791	Frame Weldment, Deck Mounting - 48" (Includes Item #27)
	461792	Frame Weldment, Deck Mounting - 52" (Includes Item #27)
6	48114-04	Grease Fitting Str. 1/4-28 Self Tap
7	04066-01	Quick Pin, .438" Dia.
8	04024-02	Nut, Push-On - 3/8" Dia.
9	04041-07	Flatwasher, 3/8" (.391 x .938 x .105)
10	04019-04	Nut, 3/8-16 Serrated Flange Hex Head
11	45325	Yoke, Caster Wheel
12	04001-80	Capscrew, Hex Head 1/2-13 x 6-1/2"
13	04021-07	Locknut, 1/2-13 Elastic Stop
14	481843	Wheel Assembly, Caster
15	481845	Tire, 11 x 4.00-5
16	481770	Retainer
17	481846	Roller Bearing
18	481844	Rim, 5" x 2-3/4" (Includes #19 & 21)
19	48114-05	Grease Fitting Str.1/4-28
20	481769	Roller Bearing .625 x 3.25"
21	**	Tire Valve, Purchase Locally
22	04062-04	Hair Pin Cotter, .177 x 3-1/4"
23	43511	Sleeve, Caster Wheel
24	04040-10	Flatwasher, 5/8" - (.688 x 1.75 x .134)
25	04017-36	Capscrew, 1/2-13 x 1" Serrated Flange Hex Head
26	04112-05	Nut, 1/2-13 Spiralock
27	04110-03	U-Nut, 3/8-16
28	04001-46	Capscrew, Hex Head 3/8-16 x 2-1/4"

* Measure the width of the engine deck to determine frame size. "Small Frame" is 16" wide.

52"A & 61"A - DECK FRAME (LARGE FRAME)

SWZU05DF48-52

52"A & 61"A - DECK FRAME (*LARGE FRAME)

Ref. No.	Part No.	Description	52A	61A
1	461280	Belt Cover With Decals	x
	461281	Belt Cover With Decals		x
2	481625-01	Knob With Stud	x	x
3	04029-03	Knob, Deck Cover Mounting	x	x
4	48100-08	Bushing, Caster	x	x
5	461793	Frame Weldment, Deck Mounting (Includes Item #27)	x
	461794	Frame Weldment, Deck Mounting (Includes Item #27)		x
6	48114-04	Grease Fitting Str. 1/4-28 Self Tap	x	x
7	04066-01	Quick Pin, .438" Dia.	x	x
8	04024-02	Nut, Push-On - 3/8" Dia.	x	x
9	04041-07	Flatwasher, 3/8" (.391 x .938 x .105)	x	x
10	04019-04	Nut, 3/8-16 Serrated Flange Hex Head	x	x
11	45325	Yoke, Caster Wheel	x	x
12	04001-80	Capscrew, Hex Head 1/2-13 x 6-1/2"	x	x
13	04021-07	Locknut, 1/2-13 Elastic Stop	x	x
14	481843	Wheel Assembly, Caster	x	x
15	481845	Tire, 11 x 4.00-5	x	x
16	481770	Retainer	x	x
17	481846	Roller Bearing	x	x
18	481844	Rim, 5.0" x 2-3/4" (Incl. #19 & 21)	x	x
19	48114-05	Grease Fitting Str. 1/4-28	x	x
20	481769	Roller Bearing .625 x 3.25"	x	x
21	**	Tire Valve, Purchase Locally	x	x
22	04062-04	Hair Pin Cotter, .177 x 3-1/4"	x	x
23	43511	Sleeve, Caster Wheel	x	x
24	04040-10	Flatwasher, 5/8" - (.688 x 1.75 x .134)	x	x
25	04017-36	Capscrew, 1/2-13 x 1" Serrated Flange Hex Head	x	x
26	04112-05	Nut, 1/2-13 Spiralock	x	x
27	04110-03	U-Nut, 3/8-16	x	x
28	04001-46	Capscrew, Hex Head 3/8-16 x 2-1/4"	x	x

* Measure the width of the engine deck to determine frame size. "Large Frame" is 20" wide.

ENGINE DECK - MANUAL START

SWZU 05 EDMAN

ENGINE DECK - MANUAL START

Ref. No.	Part No.	Description	15KA	17KA	19KAI	18KH	18HN
1	482804	Engine, 15KA Kawasaki	x
	482805	Engine, 17KA Kawasaki		x
	482928	Engine, 19KAI Kawasaki			x
	482854	Engine, 18KH Kohler				x
	482705	Engine, 18HN Honda					x
2	04040-15	Flatwasher, 5/16 (.375 x .875 x .083)	x	x	x	x	x
3	04001-09	Capscrew, 5/16-18 x 1" Hex Head	x	x	x	x	x
4	482547	Cap, Fuel Tank	x	x	x	x	x
5	461729	Fuel Tank Assy. (incl. 8, 9)	x	x	x	x	x
6	48309	Bushing	x	x	x	x	x
7	48308	Valve, Fuel Shut-off	x	x	x	x	x
8	48059-01	Clamp, Fuel Hose	x	x	x	x	x
9	48058	Fuel Hose, 1/4 ID x 23"	x	x
	48058	Fuel Hose, 1/4 ID x 18"			x
	48058	Fuel Hose, 1/4 ID x 11"				x
	48058	Fuel Hose, 1/4 ID x 26"					x
10	48028-05	Cable Tie	x	x	x	x	x
11	04003-11	Carriage Bolt, 3/8-16 X 1-1/4"	x	x	x	x	x
12	423748	Brace	x	x	x	x	x
13	04043-04	Flat Washer .391 x .938 x .105	x	x	x	x	x
14	04021-09	Nut, 3/8-16 Elastic Stop	x	x	x	x	x
15	04021-08	Nut, 1/4-20 Elastic Stop	x	x	x	x	x
16	461745	Engine Deck, 16" Wide, w/decals	x	x	x	x	x
17	04003-09	Bolt, 1/4-20 x 1-1/4" Carriage	x	x	x	x	x
18	04001-17	Bolt, 5/16-18 x 2" Hex Head	x	x	x	x	x
19	04019-03	Nut, 5/16-18 Serr. Flange	x	x	x	x	x
20	482902	Manifold, Exhaust					x
21	482903	Clamp, Muffler					x
22	04021-10	Nut, 5/16-18 Elastic Stop	x	x	x	x	x
23	04003-04	Carriage Bolt, 5/16-18 x 1"	x	x	x	x	x
24	48030-09	Clamp	x	x	x	x	x
25	421370	Clutch Bracket	x	x	x	x	x
26	04017-19	CapScrw, 5/16-18 x 1.50" Sr. Flg	x	x	x	x	x
27	481717	Wire Hrns. Adapter, 15KA, 17KA & 19 KAI	x	x	x
28	45418	Pulley Guard, 16" Frame	x	x	x	x	x
29	423476	Heatshield	x
29A	424125	Heatshield		x	x	x	x
30	04017-19	Bolt, 5/16-18 x 1" Serrated Flange Hex Head	x	x	x	x	x
31	04030-03	Lock Washer 5/16"	x	x	x	x	x
32	***	Rectifier (Purchase from Honda, p/n 31750-769-751)					x
33	423943	Mounting Bracket, Rectifier					x
34	04003-06	Bolt, 1/4-20 x 1" Carriage					x
35	482901	Muffler					x

ENGINE DECK - ELECTRIC START (SWZU-21KAE)

SWZU 05 EDELCT

ENGINE DECK - ELECTRIC START (SWZU-21KAE)

Ref. No.	Part No.	Description
1	481964	Engine, 21KAE Kawasaki
2	04040-15	Flatwasher, 5/16 (.375 x 875 x .083)
3	04001-09	Capscrew, 5/16-18 x 1" Hex Head
4	482547	Cap, Fuel Tank
5	461729	Fuel Tank Assy. (incl. 6, 7)
6	48309	Bushing
7	48308	Valve, Fuel Shut-off
8	48059-01	Clamp, Fuel Hose
9	48058	Fuel Hose, 1/4 ID x 20"
10	48028-05	Cable Tie
11	**	Battery (Not Available Through Scag)
12	04001-44	Bolt, 1/4-20 x .50"
13	04020-02	Nut, 1/4-20
14	48099	Pad
15	42392	Battery Cover
16	04029-01	Wing Nut, 1/4-20
17	423746	Battery Support
18	48661	Pad, Rubber
19	04003-01	Bolt, 1/4-20 x 6" Carriage
20	04003-11	Carriage Bolt, 3/8-16 X 1-1/4"
21	424009	Brace
22	04043-04	Flat Washer .391 x .938 x .105
23	04021-09	Nut, 3/8-16 Elastic Stop
24	461748	Engine Deck, w/decals
25	04001-17	Bolt, 5/16-18 x 2" Hex Head
26	04019-03	Nut, 5/16-18 Serr. Flange
27	04030-03	Lock Washer 5/16"
28	04021-10	Nut, 5/16-18 Elastic Stop
29	04003-04	Carriage Bolt, 5/16-18 x 1"
30	48030-09	Clamp
31	421370	Clutch Bracket
32	04017-19	CapScrw, 5/16-18 x 1.50" Sr. Flg.
33	45419	Pulley Guard
34	48029-02	Battery Cable, 31.5" Red
35	48029-14	Battery Cable, 31.5" Black
36	423308	Battery Box
37	48126	Rubber Boot
38	04003-12	Carriage Bolt, 5/16-18 x .75"
39	422882	Heatshield
40	04017-19	Bolt, 5/16-18 x 1" Sr. Flg. Hex Head

DRIVE AND BRAKE COMPONENTS

SWZ05D&BC

DRIVE AND BRAKE COMPONENTS

Ref. No.	Part. No.	Description	17KA
			15KA	19KAI	21KAE	18KH	18HN
1	481876	Ring, Split	x	x	x	x	x
2	04001-19	Bolt, 3/8-16 x 1" Hex Head	x	x	x	x	x
3	45842	Brake Shaft Assembly Weldment (16" Small Frame)	x	x		x	x
3A	45854	Brake Shaft Assembly Weldment (20" Large Frame)			x
4	04062-01	Hair Pin Cotter, .094 x 1.62	x	x	x	x	x
5	04003-12	Carrage Bolt, 5/16-18 x .75"	x	x	x	x	x
6	44126	Rod, Brake Lower	x	x	x	x	x
7	04019-04	Nut, 3/8-16 Serr. Flange	x	x	x	x	x
8	43415	Bushing, Brake	x	x	x	x	x
9	48114-05	Grease Fitting	x	x	x	x	x
10	45860	Brake Actuator Wlmt., LH	x	x	x	x	x
10A	45861	Brake Actuator Wlmt., RH	x	x	x	x	x
11	04001-46	Bolt, 3/8-16 x 2-1/4"	x	x	x	x	x
12	481871	Tire, 18 x 6.50, 4 ply	x
	481869	Tire, 18 x 8.50, 4 ply		x	x	x	x
13	481890	Rim Assy	x
	481868	Rim Assy		x	x	x	x
14	422214	Lock Washer, Wheel Motor	x	x	x	x	x
15	48679	Hex Castle Nut, 3/4-28 UNEF	x	x	x	x	x
16	04028-02	Nut, Lug	x	x	x	x	x
17	481870	Wheel Assy., (incl. #12 & 13)	x
	481867	Wheel Assy., (incl. #12 & 13)		x	x	x	x
18	422215	Brake Drum	x	x	x	x	x
19	04008-01	1/2-20 Serrated Bolt	x	x	x	x	x
20	46928	Hub, Wheel	x	x	x	x	x
21	481470	Brake Band, 7.5"	x	x	x	x	x
22	04063-07	Key, 3/16 X .75 Woodruff	x	x	x	x	x
23	481416	Wheel Motor	x	x	x	x	x
24	481837	Belt, Pump Drive (16" Small Frame)	x	x		x	x
24A	481864	Belt, Pump Drive (20" Large Frame)			x
25	461397	Electric Clutch	x	x	x	x	x
26	04041-28	Flat Washer .469 x 1.75 x .25	x	x	x	x	x
27	04030-05	Lock Washer, 7/16	x	x	x	x	x
28	04102-05	Hex Head Bolt, 7/16-20 x 2-3/4"	x	x	x	x	x
29	422534	Plate, Backing	x	x	x	x	x
30	48030-09	Clamp	x	x	x	x	x
31	04021-10	Nut, 5/16-18 Elastic Stop	x	x	x	x	x
32	481716	Rubber Pad, Clutch Stop	x	x	x	x	x
33	422533	Retainer, Clutch Stop	x	x	x	x	x
34	04001-12	Hex Head Bolt, 5/16-18 x 1.75"	x	x	x	x	x
35	482754	Pulley, Pump Drive Engine	x	x	x	x	x
36	04001-13	Hex Head Bolt, 5/16-18 x 2.75"	x	x	x	x	x
37	04021-05	Nut, 3/8-16 Center Lock	x	x	x	x	x
38	48224	Ball Bearings	x	x	x	x	x
39	461783	Idler Arm Weldment, Pump (incl. 38)	x	x	x	x	x
40	04001-172	Bolt, Hex Head 1/4-20 x 1" Grd 8	x	x	x	x	x
41	481835	Spring, Pump Belt Idler	x	x	x	x	x
42	04019-03	Nut, 5/16-18 Serr. Flange	x	x	x	x	x
43	04050-02	Retaining Ring, 3/4" Ext. "E"	x	x	x	x	x
44	04063-29	Key, 1/4x1/4 x 3.75"	x	x	x	x	x
45	04041-07	Flat Washer, 3/8	x	x	x	x	x
46	482306	Pulley, Idler 4.5"	x	x	x	x	x
47	482649	Pulley, Pump Shaft	x	x	x	x	x
48	482085	Tapered Hub	x	x	x	x	x
49	04030-04	Lockwasher, 3/8	x	x	x	x	x
50	04063-14	Key, 5.0 x 5.0 x 25mm	x	x	x	x	x
51	43504	Pivot, Idler (Long)	x	x	x	x	x
52	43032	Swivel Joint	x	x	x	x	x
53	422713	Base, Idler Pivot	x	x	x	x	x
54	04001-54	Bolt, Hex Head 3/8-16 x 3"	x	x	x	x	x
55	04001-161	Bolt, Hex Head 3/8-16 x 2.75"	x	x	x	x	x
56	04043-04	Flatwasher 3/8"	x	x	x	x	x
57	481873	Chain	x	x	x	x	x
58	04001-59	Bolt, Hex Head 1/4-20 x 1.25"	x	x	x	x	x
59	04021-09	Nut, Hex Elastic Stop 3/8-16	x	x	x	x	x
60	04019-02	Nut, Serrated Flange 1/4-20	x	x	x	x	x
61	04001-151	Bolt, Hex Head 3/8-16 x 2.63"	x	x	x	x	x

NOTES

- NOTE -

THE FOLLOWING 2 PAGES CONTAIN THE ILLUSTRATED PARTS BREAKDOWN FOR THE HANDLE ASSEMBLY INSTALLED ON MACHINES IN THE FOLLOWING SERIAL NUMBER RANGES.

SWZU48A-17KA with a serial number of A2500001 to A2500100

SWZU52A-17KA with a serial number of A2700001 to A2700100

HANDLE ASSEMBLY

SMALL FRAME (16")

HANDLE ASSEMBLY
*SMALL FRAME (16")

Ref. No.	Part No.	Description	Ref. No.	Part No.	Description
1	461781	Upper Handle Wlmt. W/Decals	56	43415	Bushing, Brake
2	42675	Quadrant, Speed Control	57	04050-02	Clip, Retaining .750 diameter
3	04062-02	Hairpin, .094 x 1.19	58	48224	Bearing, Ball Neutral Return
4	45282	Lever, Speed Adjustment	59	46747	Cam, Neutral (incl. grease ftng.)
5	43086	Bushing, Speed Adjustment Lever	60	48114-05	Grease Fitting, 1/4-28 UNF
6	04001-20	Hex Head Bolt, 3/8-16 x 1.5"	61	04050-01	Retaining Ring, 5/8"
7	48493-01	Ball Plunger	62	04001-09	Hex Head Bolt, 5/16-18 x 1"
8	48092	Knob, Speed Adjustment	63	482146	Lever, Speed Control
9	04014-01	Capscrew, 1/4-20 x 3/4" FHHS	64	04017-05	Bolt, Hex Head 1/4-20 x.75"
10	04021-08	Nut, 1/4-20 Elastic Stop	65	482431	Linkage Assembly
11	04021-10	Nut, 5/16-18 Elastic Stop	66	04041-07	Flat Wshr., 15/16 x .3906 x 12 ga
12	04010-01	Screw, #10-32 x 1/2" PW HD	67	461745	Deck, Engine 16" Wide
13	48946	Throttle Control	68	04001-10	Hex Head Bolt, 5/16-18 x 1.25"
14	04019-01	Nut, #10-32 Serr. Flange	69	482314	Choke Control
15	48312	Bushing	70	04001-152	Bolt, Hex Head 3/8-16 x 4.25"
16	451691	Handle, Oper. Presence-RH	71	422373	Plate, Threaded
	451689	Handle, Oper. Presence-LH	72	43520	Swivel Joint, Steering Rod
17	481687	Switch,Elec.Clutch Eng. (incl.Nut)	73	48100-06	Bushing
18	482686	Wire Harness	74	44144	Rod, Offset
19	48609	Key Switch	75	481545	Switch, Parking Brake
20	461242	Neutral Latch-RH	76	461481	Control, LH (inc. bush. & decal)
	461241	Neutral Latch-LH		461482	Control, RH (inc. bush. & decal)
21	48717	Switch, Neutral Interlock	77	04030-02	Lockwasher, 1/4"
22	483041	Plug, Handlebar	78	43032	Swivel Joint
23	04032-01	Washer, Curved Spring	79	44143	Rod, Brake Lever
24	04040-15	Flat Washer	80	04001-45	Hex Hd. Bolt, 3/8-16 x 2.00"
25	04021-10	Nut, 5/16-18 Elastic Stop	81	48464	Ball Joint, RH Thread
26	04001-17	Hex Head Bolt, 5/16-18 x 2"	82	04021-09	Nut, 3/8-16 Elastic Stop
27	04001-53	Hex Hd. Bolt, 5/16-18 x 2.5"	83	04010-12	Screw #10-32 Sld Hex Wshr Hd
28	483042	Lever, Steering Control	84	04001-01	Bolt, 1/4-20 x .75"
29	04030-04	Lockwasher, 3/8 Spring	85	43286	Spacer
30	44141	Rod, Steering Control	86	461605	Parking Brake Lever with Grip
31	483040	Spring, Operator Presence	87	48717	Switch, Safety
32	04017-27	Capscr., 3/8-16 x 1" Ser. Flange	88	04020-14	Nut, 3/8-24
33	482348	Spring	89	423876	Mounting Bracket, Wrench
34	04019-04	Nut, 3/8-16 Serr. Flange	90	423875	Wrench
35	44142	Rod Speed Control	91	48342	Grip, Parking Brake
36	451562	Bellcrank, Speed Control	92	421203	Plate, Threaded
37	04012-02	Setscrew, 1/4-28 x .25"	93	04062-01	Hairpin, .094 x 1.62"
38	46335	Cam, Speed Control (incl. SS)	94	424113	Bracket, Choke Mtg.
39	43166	Jackshaft, Speed Control	95	44126	Rod, Lower Brake
40	04063-13	Key, 1/8 x 1/2" Woodruff	96	422273	Plate, Coupler
41	04060-06	Roll Pin, 3/16-.75	97	451113	Shaft, Pump Control
42	04021-10	Nut, Elastic Stop 3/8-16	98	481879	Spring
43	48223	Flange, Bearing	99	04021-09	Nut, 3/8-16 Elastic Stop
44	04017-17	Capscrew, 5/16-18 x 1" Serr. Flg.	100	48829	Block, Pump Control
45	04019-03	Nut, 5/16-18 Serrated Flange
46	422795	Plate, Side
47	43536	Spacer, Neutral Bearing
48	48409	Bearing, Speed Ctrl. Bellcrank
49	04001-69	Hex Head Bolt, 5/16-18 x 1-3/4"
50	48494-02	Spring, Return
51	43522	Spacer, Side Plate
52	04041-08S	Flat Wshr., .766 x 1.25 x .035
53	04063-07	Key, Woodruff, 3/16 x .75"
54	04001-59	Bolt, Hex Head, 1/4-20 x 1.25
55	04001-19	Bolt, Hex Head 3/8-16 x 1"

* Measure the width of the engine deck to determine frame size. "Small Frame" is 16" wide.

NOTES

- NOTE -

THE FOLLOWING PAGES CONTAIN THE ILLUSTRATED PARTS BREAKDOWN FOR THE HANDLE ASSEMBLY INSTALLED ON MACHINES IN THE FOLLOWING SERIAL NUMBER RANGES.

SWZU36A-15KA with a serial number of A2300001 to A2399999

SWZU48A-17KA with a serial number of A2500101 to A2599999

SWZU48A-18HN with a serial number of A2600001 to A2699999

SWZU52A-17KA with a serial number of A2700101 to A2799999

SWZU52A-18HN with a serial number of A2800001 to A2899999

SWZU52A-18KH with a serial number of A2900001 to A2999999

SWZU52A-19KAI with a serial number of A3000001 to A3099999

SWZU-21KAE with a serial number of A3600001 to A3699999

HANDLE ASSEMBLY

SMALL FRAME (16")

HANDLE ASSEMBLY
*SMALL FRAME (16")

Ref. No.	Part No.	Description	15KA 19KAI			Ref. No.	Part No.	Description	15KA 19KAI
			17KA	18HN	18KH				17KA	18HN	18KH
1	461839	Upper Handle Wlmt. W/Decals	x	x	x	56	43415	Bushing, Brake	x	x	x
2	42675	Quadrant, Speed Control	x	x	x	57	04050-02	Clip, Retaining .750 diameter	x	x	x
3	04062-02	Hairpin, .094 x 1.19	x	x	x	58	48224	Bearing, Ball Neutral Return	x	x	x
4	45282	Lever, Speed Adjustment	x	x	x	59	46747	Cam, Neutral (incl. grease ftng.)	x	x	x
5	43086	Bushing, Speed Adjustment Lever	x	x	x	60	48114-05	Grease Fitting, 1/4-28 UNF	x	x	x
6	04001-20	Hex Head Bolt, 3/8-16 x 1.5"	x	x	x	61	04050-01	Retaining Ring, 5/8"	x	x	x
7	48493-01	Ball Plunger	x	x	x	62	04001-09	Hex Head Bolt, 5/16-18 x 1"	x	x	x
8	48092	Knob, Speed Adjustment	x	x	x	63	482146	Lever, Speed Control	x	x	x
9	04014-01	Capscrew, 1/4-20 x 3/4" FHHS	x	x	x	64	04017-05	Bolt, Hex Head 1/4-20 x.75"	x	x	x
10	04021-08	Nut, 1/4-20 Elastic Stop	x	x	x	65	482431	Linkage Assembly	x	x	x
11	04021-10	Nut, 5/16-18 Elastic Stop	x	x	x	66	04041-07	Flat Wshr., 15/16 x .3906 x 12 ga	x	x	x
12	04010-01	Screw, #10-32 x 1/2" PW HD	x	x	x	67	461745	Deck, Engine 16" Wide	x	x	x
13	48946	Throttle Control	x	x		68	04001-10	Hex Head Bolt, 5/16-18 x 1.25"	x	x	x
	482814	Throttle Control			x	69	482314	Choke Control	x	x
14	04019-01	Nut, #10-32 Serr. Flange	x	x	x	70	04001-152	Bolt, Hex Head 3/8-16 x 4.25"	x	x	x
15	483142	Bushing	x	x	x	71	422373	Plate, Threaded	x	x	x
16	451759	Handle, Oper. Presence-RH	x	x	x	72	43520	Swivel Joint, Steering Rod	x	x	x
	451757	Handle, Oper. Presence-LH	x	x	x	73	48100-06	Bushing	x	x	x
17	481687	Switch,Elec.Clutch Eng. (incl.Nut)	x	x	x	74	44144	Rod, Offset	x	x	x
18	482686	Wire Harness	x	x	x	75	481545	Switch, Parking Brake	x	x	x
19	48609	Key Switch	x	x	x	76	461481	Control, LH (inc. bush. & decal)	x	x	x
20	461242	Neutral Latch-RH	x	x	x		461482	Control, RH (inc. bush. & decal)	x	x	x
	461241	Neutral Latch-LH	x	x	x	77	04030-02	Lockwasher, 1/4"	x	x	x
21	48717	Switch, Neutral Interlock	x	x	x	78	43032	Swivel Joint	x	x	x
22	483161	Plug, Handlebar	x	x	x	79	44143	Rod, Brake Lever	x	x	x
23	04032-01	Washer, Curved Spring	x	x	x	80	04001-45	Hex Hd. Bolt, 3/8-16 x 2.00"	x	x	x
24	04040-15	Flat Washer	x	x	x	81	48464	Ball Joint, RH Thread	x	x	x
25	04021-10	Nut, 5/16-18 Elastic Stop	x	x	x	82	04021-09	Nut, 3/8-16 Elastic Stop	x	x	x
26	04001-17	Hex Head Bolt, 5/16-18 x 2"	x	x	x	83	04010-12	Screw #10-32 Sltd Hex Wshr Hd	x	x	x
27	04001-53	Hex Hd. Bolt, 5/16-18 x 2.5"	x	x	x	84	04001-01	Bolt, 1/4-20 x .75"	x	x	x
28	483042	Lever, Steering Control	x	x	x	85	43286	Spacer	x	x	x
29	04030-04	Lockwasher, 3/8 Spring	x	x	x	86	461605	Parking Brake Lever with Grip	x	x	x
30	44141	Rod, Steering Control	x	x	x	87	48717	Switch, Safety	x	x	x
31	483040	Spring, Operator Presence	x	x	x	88	04020-14	Nut, 3/8-24	x	x	x
32	04017-27	Capscr., 3/8-16 x 1" Ser. Flange	x	x	x	89	423876	Mounting Bracket, Wrench	x	x	x
33	482348	Spring	x	x	x	90	423875	Wrench	x	x	x
34	04019-04	Nut, 3/8-16 Serr. Flange	x	x	x	91	48342	Grip, Parking Brake	x	x	x
35	44142	Rod Speed Control	x	x	x	92	421203	Plate, Threaded	x	x	x
36	451562	Bellcrank, Speed Control	x	x	x	93	04062-01	Hairpin, .094 x 1.62"	x	x	x
37	04012-02	Setscrew, 1/4-28 x .25"	x	x	x	94	424113	Bracket, Choke Mtg.	x	x
38	46335	Cam, Speed Control (incl. SS)	x	x	x	95	44126	Rod, Lower Brake	x	x	x
39	43166	Jackshaft, Speed Control	x	x	x	96	422273	Plate, Coupler	x	x	x
40	04063-13	Key, 1/8 x 1/2" Woodruff	x	x	x	97	451113	Shaft, Pump Control	x	x	x
41	04060-06	Roll Pin, 3/16-.75	x	x	x	98	481879	Spring	x	x	x
42	04021-10	Nut, Elastic Stop 3/8-16	x	x	x	99	04021-09	Nut, 3/8-16 Elastic Stop	x	x	x
43	48223	Flange, Bearing	x	x	x	100	48829	Block, Pump Control	x	x	x
44	04017-17	Capscrew, 5/16-18 x 1" Serr. Flg.	x	x	x
45	04019-03	Nut, 5/16-18 Serrated Flange	x	x	x
46	422795	Plate, Side	x	x	x
47	43536	Spacer, Neutral Bearing	x	x	x
48	48409	Bearing, Speed Ctrl. Bellcrank	x	x	x
49	04001-69	Hex Head Bolt, 5/16-18 x 1-3/4"	x	x	x
50	48494-02	Spring, Return	x	x	x
51	43522	Spacer, Side Plate	x	x	x
52	04041-08S	Flat Wshr., .766 x 1.25 x .035	x	x	x
53	04063-07	Key, Woodruff, 3/16 x .75"	x	x	x
54	04001-59	Bolt, Hex Head, 1/4-20 x 1.25	x	x	x
55	04001-19	Bolt, Hex Head 3/8-16 x 1"	x	x	x

* Measure the width of the engine deck to determine frame size. "Small Frame" is 16" wide.

HANDLE ASSEMBLY

LARGE FRAME (SWZU-21KAE)

HANDLE ASSEMBLY
LARGE FRAME (SWZU-21KAE)

Ref. No.	Part No.	Description	Ref. No.	Part No.	Description
1	461840	Upper Handle Wlmt. W/Decals	52	04041-08S	Flat Wshr., .766 x 1.25 x .035
2	42675	Quadrant, Speed Control	53	04063-07	Key, Woodruff, 3/16 x .75"
3	04062-02	Hairpin, .094 x 1.19	54	04001-59	Bolt, Hex Head, 1/4-20 x 1.25
4	45282	Lever, Speed Adjustment	55	04001-19	Bolt, Hex Head 3/8-16 x 1"
5	43086	Bushing, Speed Adjustment Lever	56	43415	Bushing, Brake
6	04001-20	Hex Head Bolt, 3/8-16 x 1.5"	57	04050-02	Clip, Retaining .750 diameter
7	48493-01	Ball Plunger	58	48224	Bearing, Ball Neutral Return
8	48092	Knob, Speed Adjustment	59	46747	Cam, Neutral (incl. grease ftng.)
9	04014-01	Capscrew, 1/4-20 x 3/4" FHHS	60	48114-05	Grease Fitting, 1/4-28 UNF
10	04021-08	Nut, 1/4-20 Elastic Stop	61	04050-01	Retaining Ring, 5/8"
11	04021-10	Nut, 5/16-18 Elastic Stop	62	04001-09	Hex Head Bolt, 5/16-18 x 1"
12	04010-01	Screw, #10-32 x 1/2" PW HD	63	482146	Lever, Speed Control
13	48946	Throttle Control	64	04017-05	Bolt, Hex Head 1/4-20 x.75"
14	04019-01	Nut, #10-32 Serr. Flange	65	482431	Linkage Assembly
15	483142	Bushing	66	04041-07	Flat Wshr., 15/16 x .3906 x 12 ga
16	451759	Handle, Oper. Presence-RH	67	461748	Deck, Engine 20" Wide
	451758	Handle, Oper. Presence-LH	68	04001-10	Hex Head Bolt, 5/16-18 x 1.25"
17	481687	Switch,Elec.Clutch Eng. (incl.Nut)	69	482314	Choke Control
18	482687	Wire Harness, Electric Start	70	04001-152	Bolt, Hex Head 3/8-16 x 4.25"
19	48798	Key Switch, Electric Srt. (inc. Hdw)	71	42413	Fuse Holder
20	461242	Neutral Latch-RH	72	43520	Swivel Joint, Steering Rod
	461241	Neutral Latch-LH	73	48100-06	Bushing
21	48717	Switch, Neutral Interlock	74	48298	Blade Fuse, 20A
22	483161	Plug, Handlebar	75	04021-01	Nut, #10-32 Elastic Stop
23	04032-01	Washer, Curved Spring	76	04010-03	Screw, #10-32 x 1.5" Phillips
24	04040-15	Flat Washer	77	04030-02	Lockwasher, 1/4"
25	04021-10	Nut, 5/16-18 Elastic Stop	78	43032	Swivel Joint
26	04001-17	Hex Head Bolt, 5/16-18 x 2"	79	44143	Rod, Brake Lever
27	04001-53	Hex Hd. Bolt, 5/16-18 x 2.5"	80	04001-45	Hex Hd. Bolt, 3/8-16 x 2.00"
28	483042	Lever, Steering Control	81	48464	Ball Joint, RH Thread
29	04030-04	Lockwasher, 3/8 Spring	82	04021-09	Nut, 3/8-16 Elastic Stop
30	44141	Rod, Steering Control	83	04010-12	Screw #10-32 Sltd Hex Wshr Hd
31	483040	Spring, Handle Return	84	04001-01	Bolt, 1/4-20 x .75"
32	04017-27	Capscr., 3/8-16 x 1" Ser. Flange	85	43286	Spacer
33	482348	Spring	86	461605	Parking Brake Lever with Grip
34	04019-04	Nut, 3/8-16 Serr. Flange	87	48717	Switch, Safety
35	44142	Rod Speed Control	88	04020-14	Nut, 3/8-24
36	451562	Bellcrank, Speed Control	89	423876	Mounting Bracket, Wrench
37	04012-02	Setscrew, 1/4-28 x .25"	90	423875	Wrench
38	46335	Cam, Speed Control (incl. SS)	91	48342	Grip, Parking Brake
39	43155	Jackshaft, Speed Control	92	421203	Plate, Threaded
40	04063-13	Key, 1/8 x 1/2" Woodruff	93	04062-01	Hairpin, .094 x 1.62"
41	04060-06	Roll Pin, 3/16-.75	94	44126	Rod, Lower Brake
42	04021-10	Nut, Elastic Stop 3/8-16	95	422273	Plate, Coupler
43	48223	Flange, Bearing	96	451113	Shaft, Pump Control
44	04017-17	Capscrew, 5/16-18 x 1" Serr. Flg.	97	481879	Spring
45	04019-03	Nut, 5/16-18 Serrated Flange	98	04021-09	Nut, 3/8-16 Elastic Stop
46	422795	Plate, Side	99	48829	Block, Pump Control
47	43536	Spacer, Neutral Bearing	100	461481	Control, LH (inc. bush. & decal)
48	48409	Bearing, Speed Ctrl. Bellcrank		461482	Control, RH (inc. bush. & decal)
49	04001-69	Hex Head Bolt, 5/16-18 x 1-3/4"	101	481545	Switch, Parking Brake
50	48494-02	Spring, Return	102	44144	Rod, Offset
51	43522	Spacer, Side Plate	103	422373	Plate, Threaded

* Measure the width of the engine deck to determine frame size. "Large Frame" is 20" wide.

HYDRAULIC ASSEMBLY

2005SWZ-HA

HYDRAULIC ASSEMBLY

Ref. No.	Part Number	Description
1	481164	Cap, Oil Reservoir
2	461428	Oil Reservoir (With Fittings)
3	482266-01	Elbow, 9/16 O-Ring x 3/8 Hose
4	48811	Hose, 3/8" ID - 10-1/4" Long (Order By The Inch)
5	48811	Hose, 3/8" ID - 7" Long (Order By The Inch)
6	48603-06	O-Ring
7	483097	Pump, PG-1JQQ-DY1X-XXXX (R.H.)
8	483098	Pump, PG-1GQQ-DY1X-XXXX (L.H.)
9	04003-11	Bolt, Carriage, 3/8-16 x 1.25"
10	481265	Hose, Pump to Wheel Motor
11	48603-02	O-Ring
12	482266-03	Elbow, 7/16-20 O-Ring x 3/8 Hose
13	48811	Hose, 3/8" ID - 8-1/4" Long (Order By The Inch)
14	482417	Oil Filter Base
15	482477	Tee, 3/8 O-Ring x JIC x 1/2 Hose
16	422794	Strap, Hydraulic Tank
17	422793	Bracket, Hydraulic Tank
18	04017-16	Capscrew, 5/16-18 x .75" Serr. Flange
19	48603-04	O-Ring
20	482266-01	Elbow, 9/16 O-Ring x 3/8 Hose
21	04019-03	Nut, 5/16-18 Serr. Flange
22	482305	Hose, Formed 1/2" ID
23	48136-13	Clamp, .69 max dia.
24	481507	Tube, Filler Neck
25	461745	Engine Deck (16" Wide) W/Decals - Small Frame
	461748	Engine Deck (20" Wide) W/Decals - Large Frame
26	04019-04	Nut, 3/8-16 Serr. Flange
27	48462-01	Oil Filter
28	48485-01	Elbow, 45 Deg.-3/4-16 JIC Male x Male 3/4-16 O-Ring
29	48136-05	Clamp, .87 max di.
30	04021-08	Nut, 1/4-20
31	482202	Elbow, 3/4-16 O-Ring x 1/2 Hose
32	48571-02	Cap, 3/4-16
33	04010-10	Screw, 1/4-20 x 2.0" Round Head Phillips

HYDRAULIC PUMP ASSEMBLY

HYDRAULIC PUMP ASSEMBLY

Ref. No.	Part Number	Description
1	HG 70516	Housing Kit
2	HG 70573	End Cap Kit
3	HG 50641	Straight Headless Pin
4	HG 50969	Hex Flange Bolt, M8-1.25 x 60mm
5	HG 51232	Housing O-Ring
6	HG 2513027	Charge Pump Kit
7	HG 50273	Gerotor Assembly
8	HG 9004101-1340	O-Ring
9	HG 50095	Socket Head Screw, M6 x 1.0-20mm
10	HG 2513030	Bypass Valve Kit
11	HG 70521	Pumpshaft Kit
12	HG 50315	Ball Bearing, 17 x 40 x 12
13	HG 51161	Lip Seal
14	HG 50329	Retaining Ring
15	HG 50951	Spacer
16	HG 70331	Cylinder Block Kit
17	HG 2003014	Block Spring
18	HG 2003017	Block Thrust Washer
19	HG 51444	Valve Plate
20	HG 2003087	Swash Plate
21	HG 50551	Ball Thrust Bearing
22	HG 2003005	Trunnion Arm
23	HG 2000015	Slot Guide
24	HG 2510062	Check Valve Kit (.024" Orifice) port “A” on Left Hand Pump, port “B” on Right Hand Pump
25	HG 70403	Charge Relief Kit
26	HG 2513043	Trunnion Seal with Retainer
27	HG 9005110-4400	Straight Thread Plug
28	HG 50408	Straight Headless Pin
29	HG 70525	Overhaul Seal Kit

ENGINE DECK
WIRE HARNESS
KOHLER (18 HP)
KAWASAKI (15 HP, 17 HP & 19 HP)
HONDA (18 HP)
PART NO. 483075
INSTRUMENT PANEL HARNESS
SWZ05WH483075

ENGINE DECK

WIRING HARNESS

REPLACEMENT DECALS & INFORMATION

481971

52 Advantage

36"A - 482297

48"A - 481953

52"A - 481954

61"A - 481955

482285

482286

481039

483044

482284

48404

481109

482165

REPLACEMENT DECALS & INFORMATION

481906

481863

481438 - SWZU 15KA, 17KA, 19KAI & 18HN

481414 - SWZU 18KH

481423 - SWZU 21 KAE

Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. This warranty is limited to the original purchaser and is not transferable. Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an Authorized Scag Service Dealer.

This warranty is limited to the following specified periods from the date of the original retail purchase for defects in materials or workmanship:

* Wear items including drive belts, blades, hydraulic hoses and tires are warranted for ninety (90) days.
* Batteries are covered for ninety (90) days.
* Frame and structural components including oil reservoir, fittings, and oil coolers are warranted for 2 years (Parts and labor 1st year; Parts only 2nd year).
* Cutter decks are warranted against cracking for a period of three (3) years. (Parts and labor 1st year; Parts only 2nd and 3rd year) The repair or replacement of the cutter deck will be at the option of Scag Power Equipment. We reserve the right to request components for evaluation. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual.
* Engines and electric starters are covered by the engine manufacturer's warranty period.
* Major drive system components are warranted for two (2) years by Scag Power Equipment. (Parts and labor 1st year; Parts only 2nd year) (Two year warranty exclude fittings, hoses, drive belts). The repair or replacement of the hydraulic pump or hydraulic motor will be at the option of Scag Power Equipment. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual.
* Electric clutches have a Limited Warranty for 2 year (Parts and labor 1st year; Parts only 2nd year).
* Cutter Spindle Assemblies 461663 have a Limited Warranty for three years (Parts and labor 1st year; Parts only 2nd and 3rd year).
* Any Scag product used for rental purposes is covered by a 90 day warranty.

The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner. Scag's responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.

This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual. The warranty does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have not been assembled or installed as specified in the Operator's Manual and Assembly Manual. The warranty does not cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability.

Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obligation to modify any mower previously manufactured. All other implied warranties are limited in duration to the two (2) year warranty period or ninety (90) days for mowers used for rental purpose. Accordingly, any such implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate two year or ninety day warranty period. Scag's obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner, mechanic's travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

DIMENSIONES APROXIMADAS SWU36A SWU48A SWU52A SWU61A

SWMU 52: Tres (3) 18"; SWMU 61: Tres (3) 21"

SWMU 36: Dos (2): 18"; SWMU 48: Tres (3) 16.5"

Marbin, epesor 0.197

35.5" (90.2 cm), 48.0 (122.0 cm), 52.0 " (132.0 cm),

SWM52A, 61A: acero calibre 10 con faldon calibre 7 (3/16")

SWMU36A, 48A: Acero calibre 7 con faldon de calibre 7 (3/16")

SWMU 36 Advantage, SWMU 48 Advantage,

0 a 3.0 mph (4.8 Kph)

0 a 7.4 mph (11.8 Kph)

AUSTE NEUTRAL (CONTINUATION)

manipular batteries.

OPERATION (CONTINUATION)

CONSIDERACIONES PREVIAIS A LA

OPERATION (CONTINUATION)

CONSIDERACIONES PREVIAIS A LA

MODELOSZWU

POWER EQUIPMENT SCAG