SW 03023 - Lawn mower Scag - Free user manual and instructions
Find the device manual for free SW 03023 Scag in PDF.
User questions about SW 03023 Scag
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Lawn mower in PDF format for free! Find your manual SW 03023 - Scag and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SW 03023 by Scag.
USER MANUAL SW 03023 Scag
SCAC®
POWER EQUIPMENT
OPERATOR'S MANUAL
MODEL SW
FROM SERIAL NUMBER 60001 TO 69999
PART 03023
WARNING:
FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY.
* Keep all shields in place, especially the grass discharge chute.
* Before performing any maintenance or service, stop the machine and remove the spark plug wire and ignition key.
* If a mechanism becomes clogged, stop the engine before cleaning.
* Keep hands, feet and clothing away from power-driven parts.
* Read this manual completely as well as other manuals that came with your mower.
REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the equipment.
This manual covers the operating instructions and illustrated parts list for:
All SW Machines with a serial number of xxx60001- xxx69999
Always use the entire serial number listed on the serial number tag when referring to this product.
Your mower was built to the highest standards in the industry. However, your mower is only as safe as the operator! Carelessness or operator error may result in serious bodily injury or death. Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the equipment. Make sure every operator is properly trained and thoroughly familiar with all of the controls before operating the equipment.
- Scag Power Equipment -
GENERAL SAFETY INSTRUCTIONS
- READ THIS OPERATOR'S MANUAL and instructions furnished with attachments.
- A replacement Operator's Manual is available from your Scag Servicing Dealer or by contacting Scag Power Equipment, Service Department at P.O. Box 152, Mayville WI 53050. Please indicate the complete model and serial number of your Scag product.
- Perform only those maintenance instructions described in this manual. If major repairs are ever needed or assistance is desired, contact an Authorized Scag Dealer. To ensure optimum performance and safety, always purchase genuine SCAG replacement parts and accessories.
NEVER use “WILL-FIT” replacement parts and accessories made by other manufacturers. THE USE OF UNAPPROVED REPLACEMENT PARTS AND ACCESSORIES WILL VOID THE WARRANTY.
EQUIPMENT SAFETY
BEFORE OPERATING
- Know the controls and how to stop quickly.
- Before attempting to start engine, shift transmission into neutral, move blade engagement switch to OFF position and move neutral latches to neutral.
- Do not allow children to operate the machine. Do not allow adults to operate the machine without proper instruction.
- Remove all debris or other objects that might be picked up and thrown by the cutter blades. Keep all bystanders away from the mowing area.
- Keep all shields, safety devices, and decals in place. If a shield, safety device or decal is defective or damaged, repair or replace it before operating. Also, tighten all loose nuts, bolts and screws to assure machine is in safe operating condition.
- Do not operate the machine while wearing sandals, tennis shoes, sneakers or shorts. Also, do not wear loose fitting clothing which could get caught in moving parts. Always wear long pants and substantial shoes. Wearing safety glasses and safety shoes is advisable and required by some local ordinances and insurance regulations.
- Fill fuel tank with clean, fresh gasoline, with a minimum octane rating of 87, before starting the engine. Avoid spilling gasoline. Since gasoline is flammable, handle it carefully.
A. Use an approved gasoline container.
B. Do not fill tank while engine is hot or running.
C. Do not smoke while handling gasoline.
D. Fill fuel tank outdoors and up to approximately 1" (25 mm) below the bottom of the filler neck.
E. Wipe up any spilled gasoline.
EQUIPMENT SAFETY CONT'D
WHILE OPERATING
- Start the engine when neutral latches are in the neutral lock position, the cutter blades are disengaged, and the transmission is in neutral.
- Do not run the engine in a confined area without adequate ventilation. Exhaust fumes are hazardous and could possibly be deadly.
- Using the machine demands attention. To prevent loss of control:
A. Mow only in daylight or when there is good artificial light.
B. Watch for holes or other hidden hazards.
C. Do not drive close to a drop-off, ditch or creek bank or other hazard.
D. Reduce speed when making sharp turns and when turning on hillsides.
E. Always be sure of your footing. Keep a firm hold on the handles and walk---never run.
F. Do not operate where conditions are slippery.
- The discharge chute must always be installed and in the down position on the side discharge cutter deck except when the Scag optional grass catcher or mulching plate are completely installed. If the discharge area should plug, shut the engine off and wait for all movement to stop before removing the obstruction.
- Disengage the blades and wait for them to stop before crossing gravel drives, walks or roads.
- Shut the engine off and wait until the blades come to a complete stop before removing the grass catcher container.
-
Never raise the cutting unit while the blades are rotating.
-
If the cutting blades should strike a solid object or the equipment should start to vibrate abnormally, stop the engine, disconnect the spark plug wire, and check immediately for the cause. Vibration is generally a warning of trouble. Check the cutting unit and traction unit for damaged or defective parts. Repair any damage before starting the engine or operating the cutter unit. Be sure blades are in good condition and blade bolts are tight.
- Always park the mower and/or start the engine on a level surface. If this is not possible, block the wheels to prevent the mower from moving when you are not in the operator's position.
- Cut grass slopes carefully. Do not start, stop or turn suddenly. When operating on a slope, start at the bottom of the slope and travel across the grade whenever possible. Never travel up and down the grade. Do not mow excessively steep slopes.
WARNING:
Reduce speed and be very careful when operating on slopes to prevent tipping. If you need to turn on a hill, always turn uphill.
- Do not touch engine or muffler while the engine is running or soon after it is stopped. These areas could be hot enough to cause a burn.
- Before leaving the operator's position or leaving the mower unattended, shift the transmission into neutral, place the neutral latches in the neutral lock position, and move the blade engagement switch to OFF. Shut the engine OFF and remove the key.
- Do not pass or stand on the grass discharge side of any mower with the engine running. Stop operation when another person approaches.
EQUIPMENT SAFETY CONT'D
- Only use Scag approved riding attachments.
Scag Approved Riding Attachments:
RS-2
RS-ZT
Using unapproved attachments, (especially "stand-up" riding attachments) may be hazardous.
MAINTENANCE AND STORAGE
- Disconnect high tension wire from spark plug to prevent accidental starting of the engine when servicing, adjusting or storing the machine.
- If the mower must be tipped to perform maintenance or adjustment, remove the battery, drain the gasoline from the fuel tank and oil from the crankcase.
- To reduce potential fire hazard, keep the engine free of excessive grease, grass, leaves and accumulations of dirt.
- Be sure the machine is in safe operating condition by keeping nuts, bolts, and screws tight. Check the blade mounting bolts and nuts frequently to be sure they are tightened.
- If the engine must be running to perform a maintenance adjustment, keep hands, feet, clothing and other parts of the body away from the cutter deck blades and other moving parts.
-
Do not overspeed the engine by changing governor settings. To be sure of safety and accuracy, have an authorized dealer check maximum engine speed with a tachometer.
-
The engine must be shut off before checking the oil or adding oil to the crankcase.
- Allow the engine to cool before storing the mower in any enclosure such as a garage or storage shed. Make sure the fuel tank is empty if the machine is to be stored in excess of 30 days. Do not store the mower near any open flame or where gasoline fumes may be ignited by a spark.
- Always store gasoline in a safety-approved, red container.
- Keep the mower and fuel container in a locked storage area to prevent children from playing and tampering with them.
- Perform only those maintenance instructions described in this manual. If major repairs are ever needed or assistance is desired, contact an Authorized Scag Dealer. To ensure optimum performance and safety, always purchase genuine SCAG replacement parts and accessories. NEVER USE “WILL-FIT” replacement parts and accessories made by other manufacturers. Using unapproved replacement parts and accessories may void the warranty.
- Be careful when servicing the battery as it contains acid, which is corrosive and could cause burns to skin and clothing.
- Batteries release explosive gases when being charged or discharged. Keep batteries away from any source of sparks and/or flame.
OPERATION
INITIAL RUN-IN
First day of use or approximately 10 hours.
- Check belts for proper tension at 2, 4 and 8 hours. Adjust as needed.
OPERATION CONT'D
- Check steering control rods for neutral adjustment. (See Adjustments, page 6)
- Check tires for proper pressure.
Caster Wheels 25 psi.
Drive Wheels 15 psi.
- Check for loose hardware. Tighten as needed.
- Check safety switches for proper adjustment:
* Engine will crank, but not start if machine is not in neutral.
* On electric start, engine will not crank if PTO switch is on.
* Engine should crank and start if machine is in neutral and PTO engagement switch is OFF.
- Grease machine fittings:
Spindle Bearings - 2 or 3
Transmission Couplers - 2
Drive Wheel Bearings - 2
Caster Wheel Bearings - 2
Caster Pivot Yoke - 2
Idler Pivot Bracket - 2
Cutter Deck Idler - 1 or 2
MOWER OPERATION
-
Read and understand the safety instructions before attempting to operate this machine.
-
Before starting engine:
* Check oil levels in engine.
* Fill tank with clean, fresh, lead-free gasoline.
* The fuel valve must be opened.
NOTE: Use gasoline with an octane rating no less than 87.
* Transmission must be in NEUTRAL.
* Blade clutch switch must be in OFF position.
* Operator's presence levers must be released.
* Neutral latches must be in neutral lock position.
* Key switch must be on.
- Start engine:
* Choke as required. If the engine is cold, pull the choke knob out. When the engine starts, slowly push choke in. If the engine stalls, repeat the above operation. When the engine is warm, choking may not be necessary.
- Engage cutter blades by lifting and pushing the blade cluch switch into the ON position. Pull the switch to the OFF position to disengage the cutter blades.
NOTE: When PTO is engaged or (possibly) disengaged, a squealing sound from the underside of the machine is normal. It is caused by the electric clutch plates meshing as the mower comes up to speed. For best equipment life, engage the clutch with the engine at 1/2 throttle, not under full load.
- Shift the transmission into gear for desired mowing speed.
NOTE: Top speed is suggested only for transport!
- While squeezing steering brake levers with both hands, release both neutral latches.
OPERATION CONT'D
- When steering brake levers are released, machine will travel straight. To make a right turn, squeeze RH lever. To turn left, squeeze LH lever.
- TO STOP wheel drive, squeeze both levers, lock neutral latches, and shift transmission into neutral.
WARNING:
To avoid serious bodily injury and damage to transmission, machine must be at full stop before shifting from forward to reverse or from reverse to forward.
- Only use Scag Approved Riding Attachments.
Scag approved riding attachments:
RS-2
RS-ZT
Using unapproved attachments, (especially
"stand-up" riding attachments) may be hazardous.
- To adjust the cutter deck drive belt: adjust the nut so that the belt moves 1/2" with 10 pounds of pressure. (See figure 1)
NOTE: Due to initial belt stretch and to prevent the belt from slipping, check this adjustment after the first 2 hours, 4 hours and 8 hours.
Figure 1
- To adjust the blade drive belt: Using a belt tension gauge, check the belt tension so the belt moves 1/2" with 10 lbs. pressure. Adjust the tension by tightening or loosening the J-bolt. (See figure 2 & 3)
ADJUSTMENTS
CUTTER DECK BELT ADJUSTMENTS
- Remove belt cover.
Figure 2
ADJUSTMENTS CONT'D
Figure 3
DRIVE CONTROLS
- Traction Plus (Accessory Option): With the hand controls released, adjust the swivels by holding the bail 2" (+/- 1/2") from the dash panel. Adjust so that the swivels just touch the bottom of the slots in the traction levers. (See figure 4)
NOTE: The key to proper operation of Traction Plus is that both swivels are touching the bottom of the traction lever slots at the same time when the bail is pulled back.
Figure 4
- Steering Control Rods: There should be approximately 3/4" clearance from the bottom of the rod to the bottom of the neutral latch slot when in the drive position. (See figure 5)
Figure 5
- Brake Rods: Adjust so that the brakes do not apply until the steering levers are pulled tight to the handles. When the steering levers are locked in the neutral position, the unit may be pushed around. (See figure 5)
TRANSMISSION DRIVE BELT
Adjust the transmission drive belt so that there is about a 3/16" deflection with 10 lbs. of pressure. Adjust by loosening idler pulley mounting bolt and sliding the idler left or right to change belt tension.
CUTTER DECK ADJUSTMENTS
Due to the many cutting conditions that exist, it is difficult to suggest a cutter deck setting that will work for every lawn. There are two adjustments that can be made on these decks, pitch and height.
ADJUSTMENTS CONT'D
PITCH is the angle of the blades (comparing front to rear). A 1/4" downward pitch (front of deck down) is recommended for best cutting performance.
HEIGHT is the nominal distance the blade is off of the ground. This measurement is made with the blades pointed side to side and distance is measured between cutting tip and ground. (Also see Blade Height Adjustment, next page)
Changes to the cutting height can also be achieved by repositioning the cutter deck. (This adjustment will also effect the pitch of the deck). There are three available positions (see figure 6).
Caster spacers also can be repositioned to change cutting heights and to change the pitch of the deck. (See figure 7)
Figure 7
Figure 6
ADJUSTMENTS CONT'D
BLADE HEIGHT ADJUSTMENT
Adjusting the blade height can be done by moving any number of the four smaller 1/4" spacers on the blade mounting bolts to the top of the spindle shaft or below the spindle shaft.
NOTE: All blades should be positioned equally.
For best cut and discharge, a minimum of three spacers should be installed between the blade and spindle. (See figure 8).
Figure 8
CUTTER BLADES
Do not sharpen beyond 1/3 of the width of the blade. (See figure 9)
NOTE: Dress the blade with a file. Using a wheel grinder may burn the blade. Check the balance of the blade. If blades are out of balance, vibration and premature wear of spindle assembly can occur. See your authorized Scag dealer for blade balancing or special tools if you choose to balance your own blades.
Figure 9
LUBRICATION & MAINTENANCE
| BREAK-IN | ||
| 8 HOURS (DAILY) | + Grease spindle until grease comes out the relief valve Compatible Greases: Lidok EP #2 (found at industrial shops) Ronex MP (Exxon service stations) Shell Alvania (Shell service stations) Mobilux #2 (Mobil service stations) Super Lub M EP #2 (Conoco service stations) | |
| 40 HOURS (WEEKLY) | ||
| 100 HOURS (BIWEEKLY) | ||
| 500 HRS OR ANNUALLY | ||
| PROCEDURE | COMMENTS | |
| Check all hardware for proper tightness Change engine oil and filter at 5 hours | ||
| Check engine oil Remove debris from under belt cover Sharpen cutter blades Grease spindle bearings Clean air filter Check belt tension Check tire pressure | Do not over fill More often if needed More often if needed + US Lithium MP White Grease 2125 More often if needed Add or adjust as required | |
| Change engine oil | See engine mfg. information | |
| Replace air filter Grease caster wheel bearings Grease caster wheel pivot shafts Grease idler pulley bracket on cutter deck Grease drive wheel bearings Grease transmission couplers Grease idler bracket LH & RH | More often if needed Chassis grease Chassis grease Chassis grease Chassis grease Chassis grease | |
| Check all hardware for proper tightness Adjust air gap on electric clutch | Contact your Scag dealer for information about making this adjustment | |
REPLACEMENT PARTS
For your convenience, we are providing a list of common replacement parts for your SCAG Product.
| Part | Description | 32 | 36 | 48 | 52 | 61 | 72 |
| 48110 | Cutter Blade 16-1/2" | x | x | ||||
| 48184 | Cutter Blade 16-1/2" High Lift | x | x | ||||
| 48108 | Cutter Blade 18" | x | x | ||||
| 48185 | Cutter Blade 18" High Lift | x | x | ||||
| 48111 | Cutter Blade 21" | x | |||||
| 48304 | Cutter Blade 21" High Lift | x | |||||
| 48112 | Cutter Blade 24" | x | |||||
| 48278 | Belt, Blade Drive | x | |||||
| 48204 | Belt, Blade Drive | x | |||||
| 48087 | Belt, RH Blade Drive | x | |||||
| 48089 | Belt, Blade Drive | x | |||||
| 48285 | Belt, RH Blade Drive | x | |||||
| 48286 | Belt, Blade Drive | x | |||||
| 48265 | Belt, RH Blade Drive | x | |||||
| 48088 | Belt, Blade Drive | x | |||||
| 48295 | Belt, RH Blade Drive | x | |||||
| 48296 | Belt, Blade Drive | x | |||||
| 48203 | Belt, Transmission Drive | x | x | x | x | x | x |
| 48202A | Belt, Wheel Drive | x | x | x | x | x | x |
| 04029-03 | Wing Nut, Belt Cover | x | x | x | x | x | x |
LUBRICATION & MAINTENANCE
| BREAK-IN 8 HOURS (DAILY) 40 HOURS (WEEKLY) 100 HOURS (BIWEEKLY) 500 HRS OR ANNUALLY | + Grease spindle until grease comes out the relief valve Compatible Greases: Lidok EP #2 (found at industrial shops) Ronex MP (Exxon service stations) Shell Alvania (Shell service stations) Mobilux #2 (Mobil service stations) Super Lub M EP #2 (Conoco service stations) | |
| PROCEDURE | COMMENTS | |
| Check all hardware for proper tightness Change engine oil and filter at 5 hours | ||
| Check engine oil Remove debris from under belt cover Sharpen cutter blades Grease spindle bearings Clean air filter Check belt tension Check tire pressure | Do not over fill More often if needed More often if needed + US Lithium MP White Grease 2125 More often if needed Add or adjust as required | |
| Change engine oil | See engine mfg. information | |
| Replace air filter Grease caster wheel bearings Grease caster wheel pivot shafts Grease idler pulley bracket on cutter deck Grease drive wheel bearings Grease transmission couplers Grease idler bracket LH & RH | More often if needed Chassis grease Chassis grease Chassis grease Chassis grease Chassis grease | |
| Check all hardware for proper tightness Adjust air gap on electric clutch | Contact your Scag dealer for information about making this adjustment | |
REPLACEMENT PARTS
For your convenience, we are providing a list of common replacement parts for your SCAG Product.
| Part | Description | 32 | 36 | 48 | 52 | 61 | 72 |
| 48110 | Cutter Blade 16-1/2" | x | x | ||||
| 48184 | Cutter Blade 16-1/2" High Lift | x | x | ||||
| 48108 | Cutter Blade 18" | x | x | ||||
| 48185 | Cutter Blade 18" High Lift | x | x | ||||
| 48111 | Cutter Blade 21" | x | |||||
| 48304 | Cutter Blade 21" High Lift | x | |||||
| 48112 | Cutter Blade 24" | x | |||||
| 48278 | Belt, Blade Drive | x | |||||
| 48204 | Belt, Blade Drive | x | |||||
| 48087 | Belt, RH Blade Drive | x | |||||
| 48089 | Belt, Blade Drive | x | |||||
| 48285 | Belt, RH Blade Drive | x | |||||
| 48286 | Belt, Blade Drive | x | |||||
| 48265 | Belt, RH Blade Drive | x | |||||
| 48088 | Belt, Blade Drive | x | |||||
| 48295 | Belt, RH Blade Drive | x | |||||
| 48296 | Belt, Blade Drive | x | |||||
| 48203 | Belt, Transmission Drive | x | x | x | x | x | x |
| 48202A | Belt, Wheel Drive | x | x | x | x | x | x |
| 04029-03 | Wing Nut, Belt Cover | x | x | x | x | x | x |
32" & 36" CUTTER DECKS
32" & 36" CUTTER DECKS
| Ref. No. | Part Number | Description | 32 | 36 | Ref. No. | Part Number | Description | 32 | 36 |
| 1 | 46849 | Cutter Deck (Includes Decals) | x | 42 | 48924 | Pulley | x | x | |
| 1A | 46850 | Cutter Deck (Includes Decals) | x | 43 | 48926 | Tapered Hub | x | x | |
| 2 | 46631 | Cutter Spindle Assy. | x | x | 44 | 04001-01 | Hex Hd. Bolt, 1/4-20 x 3/4" | x | x |
| 3 | 43312 | Spacer, Outside | x | x | 45 | 04020-09 | Hex Nut, 5/8-11 | x | x |
| 4 | 48307-08 | Tapered Nut, 5/16-24 | x | x | 46 | 48278 | Belt, Blade Drive | x | |
| 5 | 481022 | Tapered Bearing (Two) | x | x | 46A | 48204 | Belt, Blade Drive | x | |
| 6 | 43294 | Spindle Housing | x | x | 47 | 43077 | Spacer | x | x |
| 7 | 04001-108 | Bolt, 5/16-18 x 4-1/4" Hex Head | x | x | 48 | 04021-05 | Hex Nut, 3/8-16 Center Locknut | x | x |
| 8 | 43298 | Spindle Shaft | x | x | 49 | 04019-04 | Nut, 3/8-16 Serrated Flange | x | x |
| 9 | 04001-77 | Bolt, 3/8-16 x 3-1/2" Hex Head | x | x | 50 | 04004-02 | Support, Belt Cover | x | x |
| 10 | 04063-08 | Key, 1/4 x 1/4 x 2" | x | x | 51 | 04017-42 | Cpscrw, 7/16-14 x 1"Ser.Flg. HH | x | x |
| 11 | 43278 | Spacer, Cutter Blade - Small | x | x | 52 | 04019-05 | Nut, 7/16-14 Serrated Flange | x | x |
| 12 | 04001-10 | Bolt,5/16-18 x 1-1/4" Hex Head | x | x | 53 | 43277 | Spacer, J-Hook | x | x |
| 13 | 481050 | Spring, Chutte Return | x | x | 54 | 04041-12 | Washer, 3/8 x 1-1/2 x 16 GA | x | x |
| 14 | 04019-03 | Nut 5/16-18 Serrated Flange | x | x | 55 | 04021-09 | Elastic Stop Nut, 3/8-16 | x | x |
| 15 | 48110 | Cutter Blade 16-1/2" | x | 56 | 45423 | Idler Pivot | x | x | |
| 15 | 48108 | Cutter Blade, 18" | x | 57 | 46748 | Idler Arm Assy. (Inc. 22 & 58) | x | x | |
| 15A | 48184 | Cutter Blade 16-1/2 Hi Lift | x | 58 | 48100-02 | Bronze Bearing | x | x | |
| 15A | 48185 | Cutter Blade, 18 Hi Lift | x | 59 | 04050-05 | Retaining Ring, 1-1/8" Ext. "E" | x | x | |
| 16 | 04040-10 | Flatwasher, 5/8 W | x | x | 60 | 44078 | J-Hook | x | x |
| 17 | 04001-41 | Hex Hd. Bolt, 5/8-11 x 9-1/2" | x | x | 61 | 48269 | Idler Pulley, Belt Clutch | x | x |
| 18 | 46079 | Caster Assembly (Inc.19-28) | x | x | 62 | 481024 | Seal, Cutter Spindle | x | x |
| 19 | 04066-01 | Quick Pin | x | x | 63 | 43297 | Spindle Bushing | x | x |
| 20 | 43037-01 | Spacer, Caster Yoke, 1/2" long | x | x | 64 | 43296 | Spacer, Inside | x | x |
| 21 | 48100-01 | Bronze Bearing | x | x | 65 | 481035 | Nut, | x | x |
| 22 | 48114-04 | Grease Fitting | x | x | 66 | 48677 | Relief Fitting, Cutter Spindle | x | x |
| 23 | 46082 | Support Assembly (Inc. 21-23) | x | x | 67 | 481025 | Seal, Cutter Spindle | x | x |
| 24 | 45006 | Caster Yoke | x | x | 68 | 48098 | Spindle Shield | x | x |
| 25 | 43022 | Sleeve, Caster Wheel Bearing | x | x | |||||
| 26 | 04001-37 | Hex Hd. Bolt, 1/2-13 x 5-1/2" | x | x | |||||
| 27 | 04021-07 | Elastic Stop Nut, 1/2-13 | x | x | |||||
| 28 | 48307 | Wheel Assy. (Inc.4, 29-34) | x | x | |||||
| 29 | 48307-02 | Tire only, Caster Wheel | x | x | |||||
| NS | 48006-03 | Inner Tube only | x | x | |||||
| 30 | 48307-04 | Rim Pair, Caster Wheel | x | x | |||||
| 31 | 48006-07 | Retainer, Bearing, Caster Wheel | x | x | |||||
| 32 | 48006-06 | Roller Bearing, Caster Wheel | x | x | |||||
| 33 | 48114-03 | Grease Fitting, 45 degree 1/4-28 | x | x | |||||
| 34 | 48006-05 | Hub Assembly | x | x | |||||
| 35 | 04017-16 | Cpscrw,5/16-18 x 3/4" Ser.Flg. Hex Head | x | x | |||||
| 36 | 461054 | Discharge Chute | x | x | |||||
| 37 | 04021-10 | Hex Nut, 5/16-18 Elastic Stop | x | x | |||||
| 38 | 04001-09 | Hex Hd Bolt, 5/16-18 x 1" | x | x | |||||
| 39 | 46853 | Belt Cover Assy (Includes Decal) | x | ||||||
| 39A | 46797 | Belt Cover Assy (Includes Decal) | x | ||||||
| 40 | 04041-07 | Flat Washer, 3/8" Special | x | x | |||||
| 41 | 04029-03 | Wing Nut, 3/8-16 | x | x |
* Common hardware which should be purchased locally. All bolts are Grade 5 plated, all other fasteners zinc plated.
48", 52", 61", & 72" CUTTER DECKS
48, 52, 61, & 72" CUTTER DECKS
| Ref. No. | Part No. | Description | 48 52 61 72 | Ref. No. | Part No. | Description | 48 52 61 72 | ||||||
| 1 | 46851 | Cutter Deck (Includes decals) | x | 45 | 04020-09 | Nut, 5/8-11 Hex | x | x | x | x | |||
| 1 | 46751 | Cutter Deck (Includes decals) | x | 46 | 48923 | Pulley, Double | x | x | |||||
| 1 | 46752 | Cutter Deck (Includes decals) | x | 46A | 48940 | Pulley, Double | x | ||||||
| 1 | 46608 | Cutter Deck (Includes decals) | x | 46B | 48966 | Pulley, Double | x | ||||||
| 2 | 46631 | Spindle Assembly | x | x | x | x | 47 | 48087 | Belt, RH Blade Drive | x | |||
| 3 | 43312 | Spacer, Inside | x | x | x | x | 47 | 48285 | Belt, RH Blade Drive | x | |||
| 4 | 48924 | Pulley | x | x | x | x | 47 | 48265 | Belt, RH Blade Drive | x | |||
| 5 | 481022 | Tapered Bearing (Two) | x | x | x | x | 47 | 48295 | Belt, RH Blade Drive | x | |||
| 6 | 43294 | Spindle Housing | x | x | x | x | 48 | 48089 | Belt, Blade Drive | x | |||
| 7 | 48114-04 | Grease Fitting Str. 5/16 | x | x | x | x | 48 | 48286 | Belt, Blade Drive | x | |||
| 8 | 43298 | Spindle Shaft, Tapered Brng | x | x | x | x | 48 | 48088 | Belt, Blade Drive | x | |||
| 9 | 45037 | Idler Pivot | x | x | x | x | 48 | 48296 | Belt, Blade Drive | x | |||
| 10 | 04063-08 | Key, 1/4 x 1/4 x 2" | x | x | x | x | 49 | 04021-05 | Nut, 3/8-16, Nut Centerlock | x | x | x | x |
| 11 | 43278 | Spacer, Cutter Blade - Small | x | x | x | x | 50 | 04019-04 | Nut, 3/8-16, Serrated Flange | x | x | x | x |
| 12 | 04001-10 | Bolt, 5/16-18 x 1-1/4" Hex Head | x | x | x | x | 51 | 04021-09 | Nut, 3/8-16 Elastic Stop | x | x | x | x |
| 13 | 04001-108 | Bolt, 5/16-18 x 4-1/4" Hex Head | x | x | x | x | 52 | 04004-02 | Support, Belt Cover | x | x | x | x |
| 14 | 04019-03 | Serrated Flange Nut, 5/16-18 | x | x | x | x | 53 | 04001-08 | Bolt, 5/16-18 x 1/2" Hex Head | x | x | x | x |
| 15 | 48110 | Cutter Blade 16-1/2" | x | 54 | 04017-42 | Cpscrw,7/16-14 x 1"Ser Fing H Hd | x | x | x | x | |||
| 15 | 48108 | Cutter Blade 18" | x | 55 | 04019-05 | Nut, 7/16-14 Serrated Flange | x | x | x | x | |||
| 15 | 48111 | Cutter Blade 21" | x | 56 | 04041-08 | Flat Washer 3/4" Special | x | x | x | x | |||
| 15 | 48112 | Cutter Blade 24" | x | 56A | 04041-08S | Flat Washer 3/4" Special | x | x | x | x | |||
| 15A | 48184 | Cutter Blade 16-1/2 Hi Lift | x | 57 | 44078 | J-Hook | x | x | x | x | |||
| 15A | 48185 | Cutter Blade 18 Hi Lift | x | 58 | 48181 | Idler Pulley, "V" Groove | x | x | x | x | |||
| 15A | 48304 | Cutter Blade 21 Hi Lift | x | 59 | 04050-02 | Retaining Ring, 3/4" Ext."E" | x | x | x | x | |||
| 16 | 04040-10 | Flatwasher, 5/8" (.688 x 1.75 x .134) | x | x | x | x | 60 | 46081 | Idler Arm Assy. (Incl. 22 & 61) | x | x | x | x |
| 17 | 04001-41 | Hex Head Bolt, 5/8-11 x 9-1/2" | x | x | x | x | 61 | 48100-05 | Bronze Bearing | x | x | x | x |
| 18 | 46079 | Caster Assembly, (incl. 19-28) | x | x | x | x | 62 | 43028 | J-Rod, Idler Pulley | x | x | x | |
| 19 | 04066-01 | Quick Pin | x | x | x | x | 62A | 44078 | J-Rod, Idler Pulley | x | |||
| 20 | 43037-01 | Spacer, Caster Yoke, 1/2" thick | x | x | x | x | 63 | 43077 | Spacer, J-Rod | x | x | x | x |
| 21 | 48100-01 | Bronze Bearing | x | x | x | x | 64 | 04041-12 | Washer, 3/8 x 1-1/2 x 16 ga. | x | x | x | x |
| 22 | 04030-03 | Lock Wshr, 5/16" (.317 x .586 x .078) | x | x | x | x | 65 | 04001-46 | Bolt, 3/8-16 x 2-1/4" Hex Head | x | x | x | x |
| 23 | 46082 | Support Assembly, (incl. 21-23) | x | x | x | x | 66 | 481024 | Seal, Cutter Spindle | x | x | x | x |
| 24 | 45006 | Caster Yoke | x | x | x | x | 67 | 46748 | Idler Arm Assy (Includes 22&77) | x | x | x | x |
| 25 | 43022 | Sleeve, Caster Wheel Bearing | x | x | x | x | 68 | 43277 | Spacer, J-Rod | x | x | x | x |
| 26 | 04001-37 | Hex Hd Bolt, 1/2-13 x 5-1/2" | x | x | x | x | 69 | 48677 | Reiief Fitting, Cutter Spindle | x | x | x | x |
| 27 | 04021-07 | Elastic Stop Nut, 1/2-13 | x | x | x | x | 70 | 43312 | Spacer, Outside, Cutter Spindle | x | x | x | x |
| 28 | 48307 | Wheel Assy. (incl. 29-34,81) | x | x | x | x | 71 | 43297 | Spindle Bushing | x | x | x | x |
| 29 | 48307-02 | Tire only, Caster Wheel | x | x | x | x | 72 | 481035 | Nut, Cutter Spindle | x | x | x | x |
| NS | 48006-03 | Inner Tube only, Caster Wheel | x | x | x | x | 73 | 04040-15 | Flat Wash., 5/16" (.375 x .875 x .083) | x | x | x | |
| 30 | 48307-04 | Rim Pair, Caster Wheel | x | x | x | x | 74 | 04001-77 | Bolt, 3/8-16 x 3-1/2" Hex Head | x | x | x | x |
| 31 | 48006-07 | Bearing Retainer, Caster Wheel | x | x | x | x | 75 | 45329 | Idler Pivot | x | x | x | x |
| 32 | 48006-06 | Roller Bearing, Caster Wheel | x | x | x | x | 76 | 48269 | Idler Pulley, Belt Clutch | x | x | x | x |
| 33 | 48114-03 | Grease Fitting 45 deg., 1/4-28 | x | x | x | x | 77 | 48100-02 | Bronze Bearing | x | x | x | x |
| 34 | 48006-05 | Hub Assembly, (incl. bolts) | x | x | x | x | 78 | 04050-05 | Retaining Ring | x | x | x | x |
| 35 | 04017-16 | Capscrew, 5/16-18 x 3/4" | x | x | x | x | 79 | 48038 | Guide Roller | x | x | x | x |
| 36 | 461055 | Discharge Chute | x | x | 80 | 45944 | Roller Shaft | x | x | x | x | ||
| 36A | 461054 | Discharge Chute | x | x | 81 | 481025 | Seal, Cutter Spindle | x | x | x | x | ||
| 37 | 04021-04 | Nut, 5/16-18 Elastic Elastic Stop | x | x | x | x | 82 | 43277 | Spacer, J-Hook | x | x | x | x |
| 38 | 04001-09 | Bolt, 5/16-18 x 1" Hex Head | x | x | x | x | 83 | 48307-08 | Nut, 3/8-24 Tapered | x | x | x | x |
| 39 | 46798 | Belt Cover (Includes decals) | x | 84 | 481050 | Spring, Chute Return | x | x | x | x | |||
| 39 | 46804 | Belt Cover (Includes decals) | x | 85 | 48098 | Spindle Shield | x | x | x | x | |||
| 39 | 46805 | Belt Cover (Includes decals) | x | ||||||||||
| 39 | 46848 | Belt Cover (Includes decals) | x | ||||||||||
| 40 | 04041-07 | Flat Washer, 3/8" Special | x | x | x | x | |||||||
| 41 | 04029-03 | Wing Nut, 3/8-16 | x | x | x | x | |||||||
| 42 | 48924 | Pulley | x | x | |||||||||
| 42A | 48753 | Pulley | x | ||||||||||
| 42B | 48967 | Pulley | x | ||||||||||
| 43 | 48926 | Tapered Hub | x | x | x | x | |||||||
| 44 | 04001-01 | Bolt, 1/4-20 x 3/4" Hex Head | x | x | x | x | |||||||
ENGINE DECK
| Ref. No. | Part No. | Description | 13KH 13KA 16BV | Ref. No. | Part No. | Description | 13KH 13KA 16BV | ||||||
| 14KH 14KA 18BV 18CVE | 14KH 14KA 18BV 18CVE | ||||||||||||
| 14KAE | 14KAE | ||||||||||||
| 1A | 48843 | Engine, 12.5HP Kohler (PS-1256) | x | 38B | 48193-03 | Rim & Bearing Assembly (incl. 39) (fits SW36,48,52,61 & 72) | x | x | x | x | |||
| 1A | 48844 | Engine, 14HP Kohler (CV 12.5T PS-1413) | x | 38C | 48253-02 | Tire, 13 x 5.00-6 2-ply (SW32 only) | x | ||||||
| 1B | 48841 | Engine 12.5HP Kawasaki (FB460-ES05) | x | 38D | 48253-03 | Rim Assembly (incl. 39) (SW32 only) | x | ||||||
| 39 | 48193-02 | Wheel Brng. NWC (OD 1.984-1.980) | x | x | x | x | |||||||
| 1B | 48842 | Engine, 14HP Kawasaki (FC420V) | x | 40 | 04042-05 | Washer, 1-1/16 x 1-3/4 x 12 ga | x | x | x | x | |||
| 1B | 481052 | Engine, 14HP Kawasaki Elec. Start | x | 40A | 04041-14 | Washer, 1-1/16 x 1-1/2 x 18 ga | x | x | x | x | |||
| 1C | 481065 | Engine, 16HP Briggs Vanguard (303772 0345 02) | x | 41 | 04050-08 | Retaining Ring, 1" Ext.- "E" | x | x | x | x | |||
| 42 | 48200 | Pulley, Wheel Drive | x | x | x | x | |||||||
| 1C | 48766 | Engine, 16HP BVE | x | 43 | 43088 | Spacer, Wheel Pulley | x | x | x | x | |||
| 1C | 481066 | Engine, 18HP Briggs Vanguard | x | 44 | 48209 | Brake Drum | x | x | x | x | |||
| 1D | 48969 | Engine, 18HP Kohler (Electric Start V-Twin) | x | 45 | 04017-19 | Bolt, 5/16-18 x 1-1/2" Serrated Flange | x | x | |||||
| 46 | 04003-03 | Bolt, 3/8-16 x 2" Carriage | x | x | x | x | |||||||
| 2 | 48030-09 | Cable Clamp | x | x | x | x | 47 | 04021-10 | Nut, 5/16-18 Elastic Stop | x | x | x | x |
| 3 | 481580 | Transmission, 5-speed (Peerless 700-070, 9 tooth spline) | x | x | x | x | 48 | 04003-11 | Bolt, 3/8-16 x 1-1/4" Carriage | x | |||
| 49 | 421703 | Battery Box | x | x | x | ||||||||
| 4 | 48231 | Neutral Safety Switch | x | x | x | x | 50 | 42330 | Bracket, Idler Pulley | x | |||
| 5 | 48122-01 | Fibre Washer, thin | x | x | x | x | 51 | 48814 | Rubber Pad, Clutch Stop | x | x | x | x |
| 5A | 48122-02 | Fibre Washer, thick | x | x | x | x | 52 | 04041-11 | Washer, 13/32 x 1-1/2 x 7 ga | x | |||
| 6 | 481581 | Coupler, Jackshaft | x | x | x | x | 53 | 45685 | Battery Support Weldment | x | x | x | |
| 7 | 48114-05 | Grease Fitting, straight 1/4-28 | x | x | x | x | 54 | 421564 | Backing Plate | x | x | x | x |
| 8 | 481582 | Jackshaft (fits SW32,36 & 48) | x | x | 55 | 48099 | Battery Cover Pad | x | |||||
| 8A | 481583 | Jackshaft (fits SW52,61 & 72) | x | x | 56 | 04003-01 | Bolt, 1/4-20 x 6" carriage | x | |||||
| 9 | 04063-09 | Key, Hi-Pro #9 | x | x | x | x | 57 | 04001-21 | Bolt, 3/8-16 x 1-3/4" Hex Head | x | |||
| 10 | 04003-12 | Bolt, 5/16-18 X 3/4" Carriage | x | x | x | x | 58 | 421370 | Anti Rotation Bracket | x | x | x | x |
| 11 | 421408 | Battery Cover | x | x | x | 59 | 04003-04 | Bolt, 5/16-18 x 1" Carriage | x | x | x | x | |
| 12 | 48402-03 | Oil Drain Extention 5-1/4" | x | 60 | 48257 | Pipe Cap | x | x | |||||
| 12A | 48402-04 | Oil Drain Extention 4-3/4" | x | 61 | 04029-01 | Wing Nut, 1/4-20 | x | x | x | ||||
| 13 | 04001-08 | Bolt, 5/16-18 X 3/4" Hex Head | x | x | x | x | 62 | 48015 | Battery | x | x | x | |
| 14 | 04040-14 | Flat Washer 1/4" (.312 X .75 X .065) | x | x | x | x | 63 | 04001-44 | Bolt, 1/4-20 x 1/2" Hex Head | x | x | x | |
| 15 | 04030-03 | Lock Wshr. 5/16" | x | x | x | x | 64 | 04020-02 | Nut, 1/4-20 | x | x | x | |
| 16 | 04019-04 | Nut, 3/8-16 Serrated Flange | x | x | x | x | 65 | 04021-08 | Nut, 1/4-20 Elastic Stop | x | x | x | x |
| 17 | 46764 | Engine Deck (fits SW32) | x | 66 | 04031-09 | Lock Washer Internal Tooth | x | x | x | x | |||
| 17A | 46765 | Engine Deck (fits SW36 &48) | x | x | 67 | 481077 | Wire Harness Adapter, Man. Start | x | |||||
| 17B | 46766 | Engine Deck (fits SW52,61 & 72) | x | x | 67 | 481054 | Wire Harness Adapter, Elec. Start | x | |||||
| 18 | 48661 | Rubber Pad | x | 68 | 04001-59 | Bolt, 1/4-20 x 1-1/4" | x | x | |||||
| 19 | 04019-03 | Nut, 5/16-18 Serrated Flange | x | x | x | 69 | 21066-2071 | Rectifier (order from Kawasaki) | x | ||||
| 20 | 04001-51 | Bolt, 3/8-16 x 3-3/4" Hex Head | x | x | x | x | 70 | 04003-02 | Bolt, 1/4-20 x 3/4" Carriage | x | x | x | x |
| 21 | 461073 | Electric Clutch (Ogura) | x | x | x | x | 71 | 04001-09 | Bolt, 5/16-18 x 1" Hex Head | x | x | x | x |
| 22 | 04041-07 | Washer, 3/8" (.391 x .938 x .105) | x | x | x | x | 72 | 421390 | Bracket, Capacitor | x | |||
| 23 | 48197 | Pulley, Transmission Input | x | x | x | x | 73 | 21013-2064 | Condenser (order from Kawasaki) | x | |||
| 24 | 04063-07 | Key, Woodruff #9 | x | x | x | x | 74 | 48029-06 | Battery Cable, 18" Red | x | |||
| 25 | 04050-09 | Retaining Ring, 5/8" Ext, Basic | x | x | x | x | 75 | 48029-11 | Battery Cable, 27" Black | x | |||
| 26 | 48203 | Belt, Transmission Drive | x | x | x | x | 75 | 48029-15 | Battery Cable, 36" Black | x | |||
| 27 | 481048 | Idler Pulley, Transmission | x | x | x | x | 75 | 48029-14 | Battery Cable, 31" Black | x | |||
| 28 | 48945 | Pulley, Traction Drive | x | x | x | x | 76 | 48029-02 | Battery Cable, 31.5" Red | x | x | x | |
| 29 | 04063-19 | Key, 1/4 x 1/4 x 3/4" | x | x | x | x | 77 | 48016 | Starter Solenoid | x | |||
| 30 | 04041-28 | Flat Washer, 7/16" Special | x | x | x | x | 78 | 04002-07 | Bolt, M8-1.25 x 1.0 | x | |||
| 31 | 04030-05 | Lock Washer,7/16" | x | x | x | x | 79 | 04021-08 | Nut, 1/4-20 Elastic Stop | x | x | x | x |
| 32A | 04001-101 | Bolt, 7/16-20 x2-1/2" Hex Head | x | 80 | 48126 | Rubber Boot | x | x | x | ||||
| 32B | 04001-102 | Bolt, 7/16-20 x 1-3/4" Hex Head | x | 81A | 43100 | Wheel Axle (SW 52,61,72) * | x | x | x | ||||
| 32C | 04002-15 | Cpsrw, M10-1.5 x55 Metric Hex Hd | x | x | 81B | 43085 | Wheel Axle (SW36,48) * | x | x | x | |||
| 33 | 04001-10 | Bolt, 5/16-18 x 1-1/4" Hex Head | x | x | x | x | 81C | 43104 | Wheel Axle (SW 32) * | x | |||
| 34 | 04030-04 | Lockwasher, Spring 3/8" | x | ||||||||||
| 35 | 04021-09 | Nut, 3/8-16 Elastic Stop | x | x | x | x | |||||||
| 36 | 04040-15 | Flat Washer, 5/16" | x | x | x | x | |||||||
| 37 | 04018-01 | Bolt, M8-1.25 x M25 Metric Hex Hd | x | x | |||||||||
| 38 | 48192 | Wheel Assembly (incl. 38A-38B) (fits SW36,48,52,61,72) | x | x | x | x | |||||||
| 38 | 48253 | Wheel Assembly (incl. 38C-38D) (SW32) | x | x | |||||||||
| 38A | 48192-02 | Tire, 13 x 6.50-6, 2-ply (fits SW36,48,52,61 & 72) | x | x | x | x | |||||||
HANDLE ASSEMBLY
390S0010A
HANDLE ASSEMBLY
| Ref. No. | Part No. | Description | 13KH 13KA 16BV | Ref. No. | Part No. | Description | 13KH 13KA 16BV | ||||||
| 14KH 14KA 18BV 18BVE | 14KH 14KA 18BV 18BVE | ||||||||||||
| 14KAE | 14KAE | ||||||||||||
| 1 | 46801 | Handle Assembly (Fits SW 36,48) | x | x | 54 | 04050-09 | Retaining Ring, 5/8 Ext. Basic | x | x | x | x | ||
| 1 | 46856 | Handle Assembly (Fits SW52,61,72) | x | x | x | x | 55 | 04017-06 | Capscrew, 1/4-20 x 1" Ser. Flange | x | x | x | x |
| 2 | 421360 | Belt Guard | x | x | x | x | 56 | 04003-01 | Bolt, 1/4-20 x 6" Carriage | x | |||
| 3 | 04017-27 | Capscrew, 3/8-16 x 1" Ser. Flange | x | x | x | x | 57 | 48030-09 | Clamp | x | x | x | x |
| 4 | 04041-07 | Washer, 3/8" (.391 x .938 x .105) | x | x | x | x | 58 | 04001-17 | Bolt, 5/16-18 x 2" Hex Head | x | x | x | x |
| 5 | 04021-09 | Nut, 3/8-16 Elastic Stop | x | x | x | x | 59 | 04019-02 | Nut, 1/4-20 Serrated Flange | x | x | x | x |
| 6 | 48755 | Spring, Idler | x | x | x | x | 60 | 04040-15 | Flatwasher, 5/16 (.375 x .875 x .083) | x | x | x | |
| 7 | 04001-10 | Bolt, 5/16-18 x 1-1/4" Hex Head | x | x | x | x | x | ||||||
| 8 | 04021-10 | Nut, 5/16-18 Elastic Stop | x | x | x | x | 61 | 04021-02 | Nut, 1/4-20 Elastic Stop | x | x | x | x |
| 9 | 04017-05 | Capscrew, 1/4-20 x 3/4" Hex Head | x | x | x | x | 62 | 48179 | Fuel Hose (Kawasaki Only) | x | |||
| 10 | 44004 | Control Rod, Steering | x | x | x | x | 63 | 48059-02 | Fuel Hose Clamp (Kaw. Only) | x | |||
| 11 | 04062-02 | Hair Pin, Small | x | x | x | x | 64 | 48057-02 | Fuel Filter (Kawasaki Only) | x | |||
| 12 | 04001-23 | Bolt, 3/8-16 x 4-1/2" Hex Head | x | x | x | x | 65 | 48058 | Fuel Hose, 1/4"ID, 10" (Kohler Only) x | ||||
| 13 | 43032 | Swivel Joint | x | x | x | x | 65A | 48058 | Fuel Hose, 1/4"ID, 20" (KAW & Brigs) | x | x | ||
| 14 | 04062-01 | Hair Pin, Large .094 Diameter | x | x | x | x | 65B | 48058 | Fuel Hose, 1/4"ID, 23" (Kohler 18CVE) | x | |||
| 15 | 45847 | Idler Bracket, RH | x | x | x | x | 66 | 48059-01 | Clamp, Fuel Hose | x | x | x | x |
| 15A | 45846 | Idler Bracket, LH | x | x | x | x | 67 | 481072 | Choke Control | x | |||
| 16 | 43092 | Idler Sleeve | x | x | x | x | 67 | 48780 | Choke Control | x | |||
| 17 | 04001-62 | Bolt, 3/8-16 x 3/4" Hex Head | x | x | x | x | 68 | 48159 | Grip, Handle | x | x | x | x |
| 18 | 04004-17 | Support Belt Guard | x | x | x | x | 69 | 48308 | Valve, Fuel Shut Off | x | x | x | x |
| 19 | 04019-04 | Nut, 3/8-16 Serrated Flange | x | x | x | x | 70 | 46174 | Fuel Tank Assy. (Incl. Bush. & Valve)x | x | x | x | |
| 20 | 04019-03 | Nut, 5/16-18 Serrated Flange | x | x | x | x | 71 | 481603 | Fuel Tank Cap | x | x | x | x |
| 21 | 04017-28 | Cpscrew, 3/16-18 x 1-1/4" Ser. Flng. | x | x | x | x | 72 | 421239 | Strap, Fuel Tank | x | x | x | x |
| 22 | 43286 | Spacer | x | x | x | x | 73 | 04010-10 | Screw, 1/4-20 x 2" Round Hd Slotted x | x | x | x | |
| 23 | 48309 | Bushing | x | x | x | x | 74 | 422279 | Shift Lever | x | x | x | x |
| 24 | 48292 | Rubber Pad, (Upper) | x | x | x | x | 75 | 421241 | Shift Lever Extention | x | x | x | x |
| 25 | 46089 | Steering Lever | x | x | x | x | 76 | 48144 | Grip, Steering Lever | x | x | x | x |
| 26 | 04017-17 | Capscrew, 5/16-18 x 1" Ser. Flng. | x | x | x | x | 77 | 04041-07 | Washer, 3/8 (.391x .938 x .105) | x | x | x | x |
| 27 | 48312 | Bushing | x | x | x | x | 78 | 04020-14 | Nut, 3/8-24 UNF | x | x | x | x |
| 28 | 04040-15 | Washer, 5/16 (.375 x .875 x .083) | x | x | x | x | 79 | 48028-05 | Cable Tie | x | x | x | x |
| 29 | 48951 | Spring, Operator Presence | x | x | x | x | 80 | 04001-53 | Bolt, 5/16-18 x 2-1/2" | x | x | x | |
| 30 | 45573 | Operator Presence Lever, LH (Small Frame) | x | x | 81 | 481411 | Bushing, Bearing Retainer | x | x | x | |||
| 82 | 481420 | Bearing | x | x | x | ||||||||
| 30A | 45571 | Operator Presence Lever, LH (Large Frame) | x | x | x | x | 83 | 04041-23 | Washer, #8-.170 x .375 x .032 | x | x | x | |
| 31 | 45572 | Operator Presence Lever, RH | x | x | x | x | |||||||
| 32 | 44005 | Brake Rod | x | x | x | x | |||||||
| 33 | 45092 | Brake Lever | x | x | x | x | |||||||
| 34 | 45093 | Brake Link | x | x | x | x | |||||||
| 35 | 42254 | Brake Link Plate | x | x | x | x | |||||||
| 36 | 04024-01 | Nut, 3/8 Push-on | x | x | x | x | |||||||
| 37 | 48114-05 | Greese Fitting, Straight 1/4-28 | x | x | x | x | |||||||
| 38 | 04050-01 | Retaining Ring, 5/8 Ext. "E" | x | x | x | x | |||||||
| 39 | 48210 | Brake Band | x | x | x | x | |||||||
| 40 | 04001-45 | Bolt, 3/8-16 x 2" Hex Head | x | x | x | x | |||||||
| 41 | 04031-08 | 1/4" Internal Tooth Lockwasher | x | x | x | x | |||||||
| 42 | 04032-01 | Curved Spring Washer | x | x | x | x | |||||||
| 43 | 04015-13 | Socket Head Capscrew #8-32 x 1/2" | x | x | x | x | |||||||
| 44 | 04020-02 | Nut, 1/4-20 Hex | x | x | x | x | |||||||
| 45 | 46942 | Neutral Latch, RH | x | x | x | x | |||||||
| 45A | 46941 | Neutral Latch, LH | x | x | x | x | |||||||
| 46 | 48205 | Rubber Pad (Lower) | x | x | x | x | |||||||
| 47 | 48202A | Belt, Wheel Drive | x | x | x | x | |||||||
| 48 | 48198 | Idler Pulley, Wheel Drive | x | x | x | x | |||||||
| 49 | 48199 | Pulley, Jackshaft (Inc. 50) | x | x | x | x | |||||||
| 50 | 04012-04 | Setscrew, Hex Socket Knurl Cup Pt. 5/16-18 (nylock) | x | x | x | x | |||||||
| 51 | 43098 | Spacer, Jackshaft Pulley | x | x | x | x | |||||||
| 52 | 48223 | Flange, Jackshaft Bearing | x | x | x | x | |||||||
| 53 | 48224 | Bearing, Jackshaft | x | x | x | x | |||||||
INSTRUMENT PANEL
SC413GB
| REF. NO. | PART NO. | DESCRIPTION | 13KH 13KA 16BV | |||
| 14KH 14KA 18BV | 18CVE | |||||
| 1 | 48717 | Switch, Neutral Interlock | x | x | x | x |
| 2A | 481071 | Throttle Control | x | x | ||
| 2B | 48946 | Throttle Control | x | x | ||
| 3 | 48787 | Engagement Switch, Electric Clutch (Inc. hardware) | x | x | x | x |
| 4A | 48609 | Key Switch (Includes hardware) | x | x | x | |
| 4B | 48798 | Key Switch (Includes hardware) | x | |||
| 5 | 48023 | Hour Meter (dealer installed) | x | x | x | x |
| 6 | * | Screw, #10-32 x .50 Phillips Washer Head | x | x | x | x |
| 7 | 04019-01 | Nut, #10-32 Serrated Flange Hex Head | x | x | x | x |
| 8 | 42413 | Bracket, Fuse Holder | x | x | x | |
| 9 | 48298 | Blade Fuse, 20A | x | x | x | |
| 10 | * | Screw, #10-32 x 1-1/2" | x | x | x | |
| 11 | 04021-01 | Nut, #10-32 Elastic Stop | x | x | x | |
| 12 | 48951 | Spring, Operator Presence | x | x | x | x |
| 13A | 481267 | Handle Wire Harness, Electric Start | x | x | ||
| 13B | 481266 | Handle Wire Harness, Manual Start | x | x | x | |
| NS | 48030-09 | Clamp, Wire Harness | x | x | x | x |
| 14 | 48788 | Relay (Electric Start Only) | x | |||
* Common hardware which should be purchased locally. All bolts grade 5 plated, all other fasteners zinc plated.
PEERLESS 700-070
FOR REFERENCE
ONLY
ORDER PARTS FROM
PEERLESS / TECUMSEH
| REF. PARTNO. NO. | DESCRIPTION | REF. PARTNO. NO. | DESCRIPTION | ||
| 1 | 772083A | Case, Transmisson | 50 | 778125 | Spur Rear (35 teeth) |
| 2 | 780086A | Needle Bearing Grease Spec | 51 | 778239A | Spur Gear (32 teeth-steel) |
| 2A | 780142 | Needle Bearing | 52 | 778124A | Spur Gear (30 teeth) |
| 3 | 770061A | Case, Transmission | 53 | 778123A | Spur Gear (25 teeth) |
| 8 | 792089A | Shift Key | 56 | 778145 | Spur Gear (12 teeth-steel) |
| 9 | 784266 | Shift Collar | 57 | 778151 | Spur Gear (15 teeth) |
| 10 | 784376 | Shift Rod & Fork | 58 | 778240 | Spur Gear (18 teeth-steel) |
| 11 | 778154 | Bevel Gear (42 teeth) | 59 | 778126A | Spur Gear (20 teeth) |
| 12 | 778176 | Bevel Pinion (14 teeth-steel) | 60 | 778127A | Spur Gear (25 teeth) |
| 20 | 792077 | Steel Ball, 5/16" dia. | 65 | 780139 | Washer |
| 21 | 792078 | Set Screw, 3/8-16 x 3/8" | 66 | 776135 | Input Shaft (3-11/16" long) |
| 22 | 792079 | Spring | 67 | 776402 | Shifter & Brake Shaft |
| 24 | 780071 | Thrust Bearing | 71 | 788069 | Square Cut Ring |
| 25 | 792073 | Screw, 1/4-20 x 1-1/4" (6) | 72 | 792074 | Threaded Plug (Shipping only, not used) |
| 27 | 792035 | Retaining Ring | 81 | 786081 | Roller Chain (No. 41 chain, 24 links) |
| 28 | 788040 | Retaining Ring | 82 | 786082 | Sprocket (9 teeth) |
| 29 | 780072 | Washer (6) | 83 | 786083 | Sprocket (18 teeth) |
| 30 | 780108 | Washer (5) | 90 | 788067B | Grease (32 oz. bottle Bentonite grease) |
| 32 | 792001 | "O" Ring | 150 | 510334 | Gasket Eliminator (Loctite #515) |
| 34 | 780105A | Flanged Bushing | 178 | 786176 | Coupling (Not used on Scag) |
| 49 | 778146A | Spur Gear (37 teeth) | 179 | 776401 | Connector Shaft (Not used on Scag) |
HANDLE WIRE HARNESS - ELECTRIC START
WIRE HARNESS WITH RELAY
PART NO. 481275
HANDLE WIRE HARNESS -
MANUAL START
PART NO. 481266
ENGINE DECK WIRE HARNESS - SW48-14KAE
PART NO. 481051
SC419G
PART NO. 481014
ENGINE DECK WRITE HARNESS - 16HP-BV ELECTRIC START
SC4206
ENGINE DECK
WIRE HARNESS -
KOHLER COMMAND
V-TWIN
PART NO. 481075
481121
481122
481270
481271
481483
DANGER
SPINNING BLADE
KEEP CLEAR
CONTACT CAN INJURE
48071
48071
48404
WARNING
INSTALL BELT COVER BEFORE OPERATING MACHINE
READ OPERATOR'S MANUAL
481039
481039
HEAVY DUTY COMMERCIAL
48072
MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS:
4,487,006
4,991,382
4,885,903
4,998,948
4,920,733
4,118,617
4,967,543
PATENTS PENDING
WARNING
ROTATING BLADES AND BELTS
- KEEP HANDS, FEET & CLOTHING CLEAR
- KEEP ALL GUARDS IN PLACE
- SHUT OFF ENGINE & DISENGAGE BLADE CLUTCH BEFORE SERVICING
- CLEAR AREA OF DEBRIS BEFORE MOWING
- USE CAUTION IN DIRECTING DISCHARGE
- KEEP BYSTANDERS, CHILDREN & PETS AWAY
- READ INSTRUCTION MANUAL BEFORE OPERATING
DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING KIT, OR ENTIRE GRASS CATCHER INSTALLED 4810
481040
481040
48
32" - 48315
36" - 48316
48" - 48318
52" - 48319
61" - 48320
72" - 48327
WARNING
FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109
481109
R N 1 2 3 4 5
48332
If incorrectly used, this machine can cause severe injury. Those who use and maintain the machine should be trained in its proper use, warned of its dangers, and should read the entire manual before attempting to set up, operate, adjust or service the machine.
LIMITED WARRANTY-COMMERCIAL EQUIPMENT
Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. This warranty is limited to the original purchaser and is not transferable. Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an Authorized Scag Service Dealer.
This warranty is limited to the following specified periods from the date of the original retail purchase for defects in materials or workmanship:
* Wear items including drive belts, blades, hoses and tires are warranted for 90 days.
* Batteries are covered for 90 days.
* Frame, deck, and structural components including oil reservoir, fittings, and oil cooler are warranted for 1 year.
* Engines and electric starters are covered by the manufacturer's warranty period.
* Drive system components are warranted for 1 year by the component manufacturer, in conjunction with Scag Power Equipment. (Excluding fittings, hoses, cooling system, oil reservoir, drive belts).
* Electric clutch components are warranted for 1 year.
Any Scag product used for rental purposes is covered by a 90 day warranty.
The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner. Scag's responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower.
This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operator's Manual. The warranty does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have not been assembled or installed as specified in the Operator's Manual and Assembly Manual. The warranty does not cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability.
Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obligation to modify any mower previously manufactured.
All other implied warranties are limited in duration to the one (1) year warranty period or ninety (90) days for mowers used for rental purpose. Accordingly, any such implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate one year or ninety day warranty period. Scag's obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner, mechanic's travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
- SCAC®
- POWER EQUIPMENT
- OPERATOR'S MANUAL
- MODEL SW
- WARNING
- FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY
- REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR
- GENERAL SAFETY INSTRUCTIONS
- EQUIPMENT SAFETY
- BEFORE OPERATING
- EQUIPMENT SAFETY CONT'D
- WHILE OPERATING
- MAINTENANCE AND STORAGE
- OPERATION
- INITIAL RUN-IN
- OPERATION CONT'D
- MOWER OPERATION
- ADJUSTMENTS
- CUTTER DECK BELT ADJUSTMENTS
- ADJUSTMENTS CONT'D
- DRIVE CONTROLS
- TRANSMISSION DRIVE BELT
- CUTTER DECK ADJUSTMENTS
- BLADE HEIGHT ADJUSTMENT
- CUTTER BLADES
- LUBRICATION & MAINTENANCE
- REPLACEMENT PARTS
- PEERLESS
- FOR REFERENCE
- ONLY
- ORDER PARTS FROM
- PEERLESS / TECUMSEH
- HANDLE WIRE HARNESS
- MANUAL START
- PART NO
- DANGER
- ROTATING BLADES AND BELTS
- LIMITED WARRANTY-COMMERCIAL EQUIPMENT
Brand : Scag
Model : SW 03023
Category : Lawn mower