PRO-LOCK-FP - Access Control System AccessPRO - Free user manual and instructions
Find the device manual for free PRO-LOCK-FP AccessPRO in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Fingerprint Access Control System |
| Brand | AccessPRO |
| Model | PRO-LOCK-FP |
| Material | Zinc Alloy & Stainless Steel |
| Dimensions (W x H x D) | 120 mm x 200 mm x 50 mm |
| Weight | 1.5 kg |
| Power Supply | 4 x AA batteries (6V DC) |
| Battery Life | Up to 12 months under normal use |
| Fingerprint Capacity | Up to 200 fingerprints |
| Fingerprint Sensor | Capacitive semiconductor sensor |
| Authentication Methods | Fingerprint, PIN code, RFID card |
| PIN Code Length | 4-12 digits |
| RFID Card Compatibility | Mifare Classic 13.56 MHz |
| RFID Reading Range | 2-5 cm |
| Door Thickness Compatibility | 35-80 mm |
| Backlit Display | LED display with touch keypad |
| User Management | Admin and user modes, up to 300 users |
| Security Features | Anti-tamper alarm, auto-lock, mechanical key override |
| Emergency Power | Micro-USB emergency power port |
| Installation | Mounts on door with included screws and template |
| Maintenance and Cleaning | Wipe with dry cloth; avoid solvents |
| Spare Parts Availability | Batteries, screws, RFID cards, and mounting plate available |
| Repair Capability | Modular design; user-replaceable battery and sensor |
| General Information | Certified CE, FCC; warranty 2 years |
Frequently Asked Questions - PRO-LOCK-FP AccessPRO
How do I install the PRO-LOCK-FP on my door?
First, measure your door thickness to ensure it is between 35-80 mm. Then use the included mounting template to mark screw holes. Drill pilot holes, attach the mounting plate, and secure the lock with the provided screws. Connect the cable from the exterior keypad to the interior unit, then insert batteries and complete the setup.
How do I enroll a new fingerprint?
Enter the admin mode by pressing the Admin button on the keypad and entering your master PIN. Navigate to 'Add User' and select 'Fingerprint'. Follow the prompts to place your finger on the sensor twice until the system confirms successful enrollment. The fingerprint will be stored with a unique ID.
What should I do if my fingerprint is not recognized?
Ensure your finger is clean and dry. Position it flat on the sensor, covering the entire reading area. Avoid using too much pressure. If the issue persists, delete the fingerprint and re-enroll it. Also check that the sensor is not scratched or covered. In an emergency, use the PIN code or mechanical key.
How do I change the batteries?
Open the interior battery compartment using a screwdriver. Replace all four AA batteries with fresh ones, observing the correct polarity. Press any key after installation to wake the lock. It is recommended to use high-quality alkaline batteries for optimal performance.
Can I use the lock with RFID cards?
Yes, the PRO-LOCK-FP supports Mifare Classic RFID cards. To add a card, go to admin mode, select 'Add User', then 'RFID card'. Hold the card near the reader area until you hear a beep. The card will be linked to a user ID and can be used for quick unlock.
What is the battery life and how do I get a low battery warning?
Under normal usage (10 unlocks per day), the batteries last up to 12 months. When batteries are low, the lock will emit intermittent beeps and display a low battery icon on the LED screen. After the first warning, you have approximately 200 unlocks before full discharge. Use the emergency power port if needed.
Is the lock waterproof?
The PRO-LOCK-FP is designed for indoor use and is not fully waterproof. It is weather-resistant when installed under a rainproof canopy, but prolonged exposure to rain or humidity can damage the electronics. We recommend installing a weather shield for outdoor applications.
How do I reset the lock to factory settings?
To reset the lock, remove the batteries and disconnect any external power. Wait for 10 minutes, then reinsert batteries. Press and hold the Reset button (located near the battery compartment) for 5 seconds until you hear a long beep. All user data will be erased and the master PIN will return to the default.
What should I do if the keypad becomes unresponsive?
First, check if the batteries are fully inserted and have adequate charge. If the issue persists, perform a soft reset by removing and reinserting the batteries. Ensure no debris is blocking the keys. If none of these work, use the mechanical key to unlock and contact support.
How many users can I store in the system?
The lock can store up to 300 users combined across fingerprints, PIN codes, and RFID cards. Each user can have multiple credentials, but the total unique credentials is limited to 300. This is ideal for small offices or residential buildings with multiple family members.
User questions about PRO-LOCK-FP AccessPRO
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Control System in PDF format for free! Find your manual PRO-LOCK-FP - AccessPRO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PRO-LOCK-FP by AccessPRO.
USER MANUAL PRO-LOCK-FP AccessPRO
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : AccessPRO
Model : PRO-LOCK-FP
Category : Access Control System